diff --git a/target/linux/mediatek/dts/mt7981b-jcg-q30-ubootmod.dts b/target/linux/mediatek/dts/mt7981b-jcg-q30-ubootmod.dts new file mode 100644 index 0000000000..952f81fe75 --- /dev/null +++ b/target/linux/mediatek/dts/mt7981b-jcg-q30-ubootmod.dts @@ -0,0 +1,238 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Copyright (C) Tianling Shen + */ + +/dts-v1/; +#include +#include + +#include "mt7981.dtsi" + +/ { + model = "JCG Q30 (custom U-Boot layout)"; + compatible = "jcg,q30-ubootmod", "mediatek,mt7981"; + + aliases { + led-boot = &status_red_led; + led-failsafe = &status_red_led; + led-running = &status_blue_led; + led-upgrade = &status_blue_led; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + gpio-keys { + compatible = "gpio-keys"; + + button-reset { + label = "reset"; + linux,code = ; + gpios = <&pio 1 GPIO_ACTIVE_LOW>; + }; + + button-wps { + label = "wps"; + linux,code = ; + gpios = <&pio 0 GPIO_ACTIVE_HIGH>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + status_red_led: led-0 { + label = "red:status"; + gpios = <&pio 8 GPIO_ACTIVE_HIGH>; + }; + + status_blue_led: led-1 { + label = "blue:status"; + gpios = <&pio 13 GPIO_ACTIVE_LOW>; + }; + }; +}; + +ð { + pinctrl-names = "default"; + pinctrl-0 = <&mdio_pins>; + + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + + nvmem-cells = <&macaddr_factory_a002a>; + nvmem-cell-names = "mac-address"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; +}; + +&mdio_bus { + switch: switch@0 { + compatible = "mediatek,mt7531"; + reg = <31>; + reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&pio>; + interrupts = <38 IRQ_TYPE_LEVEL_HIGH>; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_flash_pins>; + status = "okay"; + + spi_nand: flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spi-nand"; + reg = <0>; + spi-max-frequency = <52000000>; + + spi-cal-enable; + spi-cal-mode = "read-data"; + spi-cal-datalen = <7>; + spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4E 0x41 0x4E 0x44>; + spi-cal-addrlen = <5>; + spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>; + + spi-tx-buswidth = <4>; + spi-rx-buswidth = <4>; + mediatek,nmbm; + mediatek,bmt-max-ratio = <1>; + mediatek,bmt-max-reserved-blocks = <64>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "BL2"; + reg = <0x00000 0x100000>; + }; + + partition@100000 { + label = "u-boot-env"; + reg = <0x100000 0x80000>; + }; + + factory: partition@180000 { + label = "Factory"; + reg = <0x180000 0x200000>; + + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_factory_a002a: macaddr@a002a { + reg = <0xa002a 0x6>; + }; + + macaddr_factory_a0024: macaddr@a0024 { + reg = <0xa0024 0x6>; + }; + }; + + partition@380000 { + label = "FIP"; + reg = <0x380000 0x200000>; + }; + + partition@580000 { + label = "ubi"; + reg = <0x580000 0x6e80000>; + }; + }; + }; +}; + +&switch { + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "wan"; + + nvmem-cells = <&macaddr_factory_a0024>; + nvmem-cell-names = "mac-address"; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; +}; + +&pio { + spi0_flash_pins: spi0-pins { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + + conf-pu { + pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP"; + drive-strength = <8>; + bias-pull-up = <103>; + }; + + conf-pd { + pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO"; + drive-strength = <8>; + bias-pull-down = <103>; + }; + }; +}; + +&uart0 { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&wifi { + status = "okay"; + + mediatek,mtd-eeprom = <&factory 0x0>; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index fc39457a25..0707d267a7 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -15,6 +15,7 @@ mediatek_setup_interfaces() ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 sfp2" "eth1 wan" ;; cudy,wr3000-v1|\ + jcg,q30-ubootmod|\ livinet,zr-3020|\ livinet,zr-3020-ubootmod|\ qihoo,360t7|\ diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac index cd15cd0afa..08efe03d1b 100644 --- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac +++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac @@ -31,7 +31,11 @@ case "$board" in # mac-address instead. [ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress [ "$PHYNBR" = "1" ] && macaddr_setbit_la $(macaddr_add $addr 1) > /sys${DEVPATH}/macaddress - ;; + ;; + jcg,q30-ubootmod) + [ "$PHYNBR" = "1" ] && \ + macaddr_setbit_la "$(mtd_get_mac_binary Factory 0x4)" > /sys${DEVPATH}/macaddress + ;; livinet,zr-3020|\ livinet,zr-3020-ubootmod) addr=$(mtd_get_mac_ascii config2 wifi5gmac) diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index c706ccd41b..f87035384a 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -176,6 +176,27 @@ define Device/glinet_gl-mt3000 endef TARGET_DEVICES += glinet_gl-mt3000 +define Device/jcg_q30-ubootmod + DEVICE_VENDOR := JCG + DEVICE_MODEL := Q30 (custom U-Boot layout) + DEVICE_DTS := mt7981b-jcg-q30-ubootmod + DEVICE_DTS_DIR := ../dts + DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 128k + PAGESIZE := 2048 + IMAGE_SIZE := 113152k + KERNEL_IN_UBI := 1 + IMAGES += factory.bin + IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE) + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata + KERNEL = kernel-bin | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb + KERNEL_INITRAMFS = kernel-bin | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd +endef +TARGET_DEVICES += jcg_q30-ubootmod + define Device/livinet_zr-3020-common DEVICE_VENDOR := Livinet DEVICE_DTS_DIR := ../dts