mediatek: update openembed som7981 support
The board has been redesigned due to previous hardware bugs (with other reasons maybe). Changes in new board: - Added a gpio beeper - Added a Atmel i2c eeprom - Added a Atmel i2c ECC accelerator - Added a Philips RTC module - Added two RS485 - Removed WPS button - Replaced USB3 port with M.2 B-key for LTE modules Also replace broken 'phy*tpt' trigger with uci netdev configuration. Keeping compatibility for old version is not necessary here as only few samples were sent to those interested in it. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
This commit is contained in:
Tianling Shen
parent
6222e84b7e
commit
8b3c05f087
@ -12,9 +12,9 @@
|
||||
compatible = "openembed,som7981", "mediatek,mt7981";
|
||||
|
||||
aliases {
|
||||
led-boot = &wlan2g_led;
|
||||
led-failsafe = &wlan2g_led;
|
||||
led-upgrade = &wlan2g_led;
|
||||
led-boot = &wlan5g_led;
|
||||
led-failsafe = &wlan5g_led;
|
||||
led-upgrade = &wlan5g_led;
|
||||
serial0 = &uart0;
|
||||
};
|
||||
|
||||
@ -26,6 +26,11 @@
|
||||
reg = <0 0x40000000 0 0x40000000>;
|
||||
};
|
||||
|
||||
beeper {
|
||||
compatible = "gpio-beeper";
|
||||
gpios = <&pio 2 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
@ -34,12 +39,6 @@
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
button-wps {
|
||||
label = "wps";
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
gpios = <&pio 0 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
@ -57,18 +56,16 @@
|
||||
gpios = <&pio 13 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wlan2g_led: led-2 {
|
||||
led-2 {
|
||||
function = LED_FUNCTION_WLAN_2GHZ;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&pio 34 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
led-3 {
|
||||
wlan5g_led: led-3 {
|
||||
function = LED_FUNCTION_WLAN_5GHZ;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
gpios = <&pio 35 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
};
|
||||
};
|
||||
@ -97,6 +94,30 @@
|
||||
};
|
||||
};
|
||||
|
||||
&i2c0 {
|
||||
clock-frequency = <400000>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&i2c0_pins>;
|
||||
status = "okay";
|
||||
|
||||
eeprom@50 {
|
||||
compatible = "atmel,24c64";
|
||||
reg = <0x50>;
|
||||
page-size = <32>;
|
||||
};
|
||||
|
||||
rtc@51 {
|
||||
compatible = "nxp,pcf8563";
|
||||
reg = <0x51>;
|
||||
#clock-cells = <0>;
|
||||
};
|
||||
|
||||
crypto@60 {
|
||||
compatible = "atmel,atecc508a";
|
||||
reg = <0x60>;
|
||||
};
|
||||
};
|
||||
|
||||
&mdio_bus {
|
||||
phy0: ethernet-phy@5 {
|
||||
reg = <5>;
|
||||
@ -107,7 +128,8 @@
|
||||
reset-deassert-us = <50000>;
|
||||
realtek,aldps-enable;
|
||||
realtek,led-link-select = <0x0 0xa7 0xa7>;
|
||||
realtek,led-act-select = <0x2>;
|
||||
realtek,led-act-select = <0x2612>;
|
||||
realtek,led-polarity-select = <0x63>;
|
||||
};
|
||||
};
|
||||
|
||||
@ -186,6 +208,13 @@
|
||||
};
|
||||
|
||||
&pio {
|
||||
i2c0_pins: i2c0-pins {
|
||||
mux {
|
||||
function = "i2c";
|
||||
groups = "i2c0_1";
|
||||
};
|
||||
};
|
||||
|
||||
spi0_flash_pins: spi0-pins {
|
||||
mux {
|
||||
function = "spi";
|
||||
@ -204,12 +233,45 @@
|
||||
mediatek,pull-down-adv = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
uart1_pins: uart1-pins {
|
||||
mux {
|
||||
function = "uart1";
|
||||
groups = "uart1_1_tx_rx";
|
||||
};
|
||||
};
|
||||
|
||||
uart2_pins: uart2-pins {
|
||||
mux {
|
||||
function = "uart2";
|
||||
groups = "uart2_0_tx_rx";
|
||||
};
|
||||
};
|
||||
|
||||
wwan_rst_h: wwan-rst-h {
|
||||
pins = "GPIO_WPS";
|
||||
drive-strength = <8>;
|
||||
mediatek,pull-down-adv = <0>;
|
||||
output-low;
|
||||
};
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart1 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart1_pins>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart2 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart2_pins>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_phy {
|
||||
status = "okay";
|
||||
};
|
||||
@ -225,5 +287,7 @@
|
||||
};
|
||||
|
||||
&xhci {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&wwan_rst_h>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
@ -75,6 +75,8 @@ netgear,wax220)
|
||||
openembed,som7981)
|
||||
ucidef_set_led_netdev "lanact" "LANACT" "green:lan" "eth1" "rx tx"
|
||||
ucidef_set_led_netdev "lanlink" "LANLINK" "amber:lan" "eth1" "link"
|
||||
ucidef_set_led_netdev "wlan2g" "WLAN2G" "green:wlan-2ghz" "phy0-ap0"
|
||||
ucidef_set_led_netdev "wlan5g" "WLAN5G" "red:wlan-5ghz" "phy1-ap0"
|
||||
;;
|
||||
openwrt,one)
|
||||
ucidef_set_led_netdev "wanact" "WANACT" "mdio-bus:0f:green:wan" "eth0" "rx tx"
|
||||
|
||||
@ -1232,7 +1232,10 @@ define Device/openembed_som7981
|
||||
DEVICE_MODEL := SOM7981
|
||||
DEVICE_DTS := mt7981b-openembed-som7981
|
||||
DEVICE_DTS_DIR := ../dts
|
||||
DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware kmod-usb3
|
||||
DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware \
|
||||
kmod-crypto-hw-atmel kmod-eeprom-at24 kmod-gpio-beeper kmod-rtc-pcf8563 \
|
||||
kmod-usb-net-cdc-mbim kmod-usb-net-qmi-wwan kmod-usb-serial-option \
|
||||
kmod-usb3 automount uqmi
|
||||
UBINIZE_OPTS := -E 5
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
|
||||
Loading…
Reference in New Issue
Block a user