ath79: add support for Ditel DT-ACU100
Ditel DT-ACU100 is a ceiling mount Router with PoE support, based on Qualcomm/Atheros QCA9531@650MHz SoC. Short specification: - QCA9531 650 MHz SoC - 1x 10/100/1000 Mbps Ethernet (wan/eth1) - 1x 10/100/1000 Mbps Ethernet (lan/eth0) - 128MB of DDR2 RAM (Winbond W971GG6SB) - 16 MB of FLASH (Winbond W25Q128FV) - 2T2R 2.4 GHz, 802.11b/g/n (wlan2g) - 1x RGB LED, 1x button - UART header on PCB with proper labelling Initial flashing instructions: Original firmware is based on OpenWrt. a) Use sysupgrade image directly in vendor GUI. b) Or via tftp: ipaddr=192.168.1.1 serverip=192.168.1.10 bootfile="firmware.bin" c) Or possibly via u-boot's `httpd` command. MAC-address mapping follows original firmware: * eth1 (wan) is the lowest mac address (art @ 0x0) * eth0 (lan) uses eth1 + 1 (art @ 0x1000) * wlan2g (phy0) uses eth1 + 2 (art @ 0x06) * unused MAC (eth1 + 3) (art @ 0x5006) Art dump (`hexdump /dev/mtd1 |grep ZZZZ`): 0000000 ZZZZ XXXX XXX0 ZZZZ XXXX XXX2 ffff ffff 0001000 0202 ZZZZ XXXX XXX1 0000 0000 0000 0000 0005000 202f bd21 0101 ZZZZ XXXX XXX3 0000 2000 flash Stock : 0x000000-0x040000(u-boot) 00x000000-0x050000(u-boot-env) 0x050000-0xfe0000(firmware) 0xfe0000-0xff0000(ditel) 0xff0000-0x1000000(art) dev: size erasesize name mtd0: 00040000 00010000 "u-boot" mtd1: 00010000 00010000 "u-boot-env" mtd2: 00f90000 00010000 "firmware" mtd3: 00290000 00010000 "kernel" mtd4: 00d00000 00010000 "rootfs" mtd5: 00190000 00010000 "rootfs_data" mtd6: 00010000 00010000 "ditel" mtd7: 00010000 00010000 "art" Root access to original firmware (only via UART) can be achieved by making a backup of configuration from web interface. Backup contains whole `/etc` directory...
This commit is contained in:
lsgxeva
parent
fc6edad566
commit
d3ef627825
@ -83,6 +83,7 @@ yuncore,a782|\
|
||||
yuncore,a930|\
|
||||
yuncore,xd3200|\
|
||||
yuncore,xd4200|\
|
||||
ditel,dt-acu100|\
|
||||
ziking,cpe46b|\
|
||||
zyxel,nbg6616)
|
||||
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x10000" "0x10000"
|
||||
|
||||
165
target/linux/ath79/dts/qca9531_ditel_dt-acu100.dts
Normal file
165
target/linux/ath79/dts/qca9531_ditel_dt-acu100.dts
Normal file
@ -0,0 +1,165 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qca953x.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
compatible = "ditel,dt-acu100", "qca,qca9531";
|
||||
model = "Ditel DT-ACU100";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_status;
|
||||
led-failsafe = &led_status;
|
||||
led-running = &led_status;
|
||||
led-upgrade = &led_status;
|
||||
label-mac-device = ð1;
|
||||
serial0 = &uart;
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_status: status {
|
||||
function = LED_FUNCTION_STATUS;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_wlan: wlan {
|
||||
function = LED_FUNCTION_WLAN;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
};
|
||||
|
||||
i2c: i2c {
|
||||
compatible = "i2c-gpio";
|
||||
|
||||
sda-gpios = <&gpio 3 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
||||
scl-gpios = <&gpio 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
||||
};
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x040000 0x010000>;
|
||||
};
|
||||
|
||||
firmware: partition@50000 {
|
||||
label = "firmware";
|
||||
reg = <0x050000 0xf90000>;
|
||||
compatible = "denx,uimage";
|
||||
};
|
||||
|
||||
ditel: partition@fe0000 {
|
||||
label = "ditel";
|
||||
reg = <0xfe0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
art: partition@ff0000 {
|
||||
label = "art";
|
||||
reg = <0xff0000 0x010000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr_art_0: macaddr@0 {
|
||||
reg = <0x0 0x6>;
|
||||
};
|
||||
|
||||
macaddr_art_6: macaddr@6 {
|
||||
reg = <0x6 0x6>;
|
||||
};
|
||||
|
||||
cal_art_1000: calibration@1000 {
|
||||
reg = <0x1000 0x440>;
|
||||
};
|
||||
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
phy-handle = <&swphy0>;
|
||||
|
||||
nvmem-cells = <&macaddr_art_6>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
ð1 {
|
||||
phy-handle = <&swphy4>;
|
||||
|
||||
nvmem-cells = <&macaddr_art_0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
|
||||
gmac-config {
|
||||
device = <&gmac>;
|
||||
switch-phy-swap = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
|
||||
nvmem-cells = <&cal_art_1000>;
|
||||
nvmem-cell-names = "calibration";
|
||||
};
|
||||
|
||||
@ -540,6 +540,9 @@ wd,mynet-wifi-rangeextender)
|
||||
xiaomi,aiot-ac2350)
|
||||
ucidef_set_led_switch "wan" "WAN" "blue:wan" "switch0" "0x02"
|
||||
;;
|
||||
ditel,dt-acu100)
|
||||
ucidef_set_led_netdev "wan" "WAN" "red:wan" "eth0"
|
||||
;;
|
||||
yuncore,a770)
|
||||
ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth1"
|
||||
ucidef_set_led_switch "lan" "LAN" "green:lan" "switch0" "0x10"
|
||||
|
||||
@ -472,6 +472,11 @@ ath79_setup_interfaces()
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth1" "1:lan" "2:lan" "3:lan" "4:lan"
|
||||
;;
|
||||
ditel,dt-acu100)
|
||||
ucidef_set_interface_wan "eth1"
|
||||
ucidef_add_switch "switch0" \
|
||||
"0u@eth0" "1:lan:1" "2:lan:4" "3:lan:3" "4:lan:2"
|
||||
;;
|
||||
phicomm,k2t)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "3:lan:1" "5:lan:2" "4:wan"
|
||||
|
||||
@ -3243,6 +3243,17 @@ define Device/xiaomi_mi-router-4q
|
||||
endef
|
||||
TARGET_DEVICES += xiaomi_mi-router-4q
|
||||
|
||||
define Device/ditel_dt-acu100
|
||||
SOC := qca9531
|
||||
DEVICE_VENDOR := Ditel
|
||||
DEVICE_MODEL := DT-ACU100
|
||||
DEVICE_PACKAGES := -kmod-ath9k -uboot-envtools kmod-usb2
|
||||
IMAGE_SIZE := 15936k
|
||||
LOADER_FLASH_OFFS := 0x50000
|
||||
SUPPORTED_DEVICES += dt-acu100
|
||||
endef
|
||||
TARGET_DEVICES += ditel_dt-acu100
|
||||
|
||||
define Device/yuncore_a770
|
||||
SOC := qca9531
|
||||
DEVICE_VENDOR := YunCore
|
||||
|
||||
Loading…
Reference in New Issue
Block a user