diff --git a/target/linux/rockchip/armv8/base-files/etc/board.d/01_leds b/target/linux/rockchip/armv8/base-files/etc/board.d/01_leds index f131af5742..92abc55f24 100644 --- a/target/linux/rockchip/armv8/base-files/etc/board.d/01_leds +++ b/target/linux/rockchip/armv8/base-files/etc/board.d/01_leds @@ -28,6 +28,11 @@ friendlyarm,nanopi-r5s) ucidef_set_led_netdev "lan1" "LAN1" "green:lan1" "eth1" ucidef_set_led_netdev "lan2" "LAN2" "green:lan2" "eth2" ;; +friendlyarm,nanopi-r6s) + ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth2" + ucidef_set_led_netdev "lan1" "LAN1" "green:lan1" "eth1" + ucidef_set_led_netdev "lan2" "LAN2" "green:lan2" "eth0" + ;; esac board_config_flush diff --git a/target/linux/rockchip/armv8/base-files/etc/board.d/02_network b/target/linux/rockchip/armv8/base-files/etc/board.d/02_network index b0cd06dbdc..a414f7f658 100644 --- a/target/linux/rockchip/armv8/base-files/etc/board.d/02_network +++ b/target/linux/rockchip/armv8/base-files/etc/board.d/02_network @@ -25,6 +25,9 @@ rockchip_setup_interfaces() friendlyarm,nanopi-r5s) ucidef_set_interfaces_lan_wan 'eth1 eth2' 'eth0' ;; + friendlyarm,nanopi-r6s) + ucidef_set_interfaces_lan_wan 'eth0 eth1' 'eth2' + ;; lunzn,fastrhino-r68s) ucidef_set_interfaces_lan_wan 'eth0 eth1 eth3' 'eth2' ;; @@ -57,7 +60,8 @@ rockchip_setup_macs() wan_mac=$(macaddr_generate_from_mmc_cid mmcblk1) lan_mac=$(macaddr_add "$wan_mac" 1) ;; - friendlyarm,nanopi-r4se) + friendlyarm,nanopi-r4se|\ + friendlyarm,nanopi-r6s) wan_mac=$(macaddr_generate_from_mmc_cid mmcblk2) lan_mac=$(macaddr_add "$wan_mac" 1) ;; diff --git a/target/linux/rockchip/armv8/base-files/etc/hotplug.d/net/40-net-smp-affinity b/target/linux/rockchip/armv8/base-files/etc/hotplug.d/net/40-net-smp-affinity index 52ecb9ea8d..663989a1ee 100644 --- a/target/linux/rockchip/armv8/base-files/etc/hotplug.d/net/40-net-smp-affinity +++ b/target/linux/rockchip/armv8/base-files/etc/hotplug.d/net/40-net-smp-affinity @@ -49,7 +49,8 @@ friendlyarm,nanopi-r4s-enterprise) set_interface_core 10 "eth0" set_interface_core 20 "eth1" ;; -friendlyarm,nanopi-r5s) +friendlyarm,nanopi-r5s|\ +friendlyarm,nanopi-r6s) set_interface_core 2 "eth0" set_interface_core 4 "eth1" set_interface_core 8 "eth2" diff --git a/target/linux/rockchip/files/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6s.dts b/target/linux/rockchip/files/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6s.dts new file mode 100644 index 0000000000..52adcfe0df --- /dev/null +++ b/target/linux/rockchip/files/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6s.dts @@ -0,0 +1,434 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Copyright (c) 2021 Rockchip Electronics Co., Ltd. + * + * Copyright (c) 2022 FriendlyElec Computer Tech. Co., Ltd. + * (http://www.friendlyelec.com) + * + * Copyright (c) 2023 Tianling Shen + */ + +/dts-v1/; + +#include +#include +#include +#include +#include "rk3588s.dtsi" +#include "rk3588-rk806-single.dtsi" + +/ { + model = "FriendlyElec NanoPi R6S"; + compatible = "friendlyarm,nanopi-r6s", "rockchip,rk3588"; + + aliases { + ethernet2 = &gmac1; + mmc0 = &sdmmc; + mmc2 = &sdhci; + serial2 = &uart2; + + led-boot = &power_led; + led-failsafe = &power_led; + led-running = &power_led; + led-upgrade = &power_led; + }; + + chosen { + stdout-path = "serial2:1500000n8"; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&reset_button_pin>; + + button-reset { + debounce-interval = <50>; + gpios = <&gpio1 RK_PC0 GPIO_ACTIVE_LOW>; + label = "reset"; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&lan1_led_pin>, <&lan2_led_pin>, <&power_led_pin>, <&wan_led_pin>; + + led-lan1 { + label = "green:lan1"; + gpios = <&gpio1 RK_PC3 GPIO_ACTIVE_HIGH>; + }; + + led-lan2 { + label = "green:lan2"; + gpios = <&gpio1 RK_PC4 GPIO_ACTIVE_HIGH>; + }; + + power_led: led-power { + label = "red:power"; + gpios = <&gpio1 RK_PC1 GPIO_ACTIVE_HIGH>; + }; + + led-wan { + label = "green:wan"; + gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_HIGH>; + }; + }; + + vcc5v0_sys: vcc5v0-sys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + vcc5v0_usb: vcc5v0-usb-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0_usb"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc5v0_sys>; + }; + + vcc5v0_host_20: vcc5v0-host-20-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&vcc5v0_host20_en>; + regulator-name = "vcc5v0_host_20"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc5v0_usb>; + }; + + vcc_3v3_pcie20: vcc3v3-pcie20-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_3v3_pcie20"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc_3v3_s3>; + }; + + vcc_1v1_nldo_s3: vcc-1v1-nldo-s3-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_1v1_nldo_s3"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + vin-supply = <&vcc5v0_sys>; + }; + + vcc_3v3_sd_s0: vcc-3v3-sd-s0-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio4 RK_PB4 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&vcc3v3_sd_en>; + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <3000000>; + regulator-min-microvolt = <3000000>; + regulator-name = "vcc_3v3_sd_s0"; + vin-supply = <&vcc_3v3_s3>; + }; + + vbus5v0_typec: vbus5v0-typec-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio1 RK_PD2 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&vbus5v0_typec_en>; + regulator-name = "vbus5v0_typec"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc5v0_usb>; + }; +}; + +&combphy0_ps { + status = "okay"; +}; + +&combphy2_psu { + status = "okay"; +}; + +&cpu_l0 { + cpu-supply = <&vdd_cpu_lit_s0>; + mem-supply = <&vdd_cpu_lit_mem_s0>; +}; + +&cpu_b0 { + cpu-supply = <&vdd_cpu_big0_s0>; + mem-supply = <&vdd_cpu_big0_mem_s0>; +}; + +&cpu_b2 { + cpu-supply = <&vdd_cpu_big1_s0>; + mem-supply = <&vdd_cpu_big1_mem_s0>; +}; + +&gmac1 { + clock_in_out = "output"; + phy-handle = <&rgmii_phy1>; + phy-mode = "rgmii-rxid"; + pinctrl-names = "default"; + pinctrl-0 = <&gmac1_miim + &gmac1_tx_bus2 + &gmac1_rx_bus2 + &gmac1_rgmii_clk + &gmac1_rgmii_bus>; + snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>; + snps,reset-active-low; + /* Reset time is 20ms, 100ms for rtl8211f */ + snps,reset-delays-us = <0 20000 100000>; + tx_delay = <0x42>; + /* rx_delay = <0x4f>; */ + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0m2_xfer>; + status = "okay"; + + vdd_cpu_big0_s0: vdd_cpu_big0_mem_s0: regulator@42 { + compatible = "rockchip,rk8602"; + reg = <0x42>; + fcs,suspend-voltage-selector = <1>; + regulator-name = "vdd_cpu_big0_s0"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <550000>; + regulator-max-microvolt = <1050000>; + regulator-ramp-delay = <2300>; + vin-supply = <&vcc5v0_sys>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_cpu_big1_s0: vdd_cpu_big1_mem_s0: regulator@43 { + compatible = "rockchip,rk8603", "rockchip,rk8602"; + reg = <0x43>; + fcs,suspend-voltage-selector = <1>; + regulator-name = "vdd_cpu_big1_s0"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <550000>; + regulator-max-microvolt = <1050000>; + regulator-ramp-delay = <2300>; + vin-supply = <&vcc5v0_sys>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; +}; + +&i2c6 { + status = "okay"; + + hym8563: rtc@51 { + compatible = "haoyu,hym8563"; + reg = <0x51>; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "hym8563"; + pinctrl-names = "default"; + pinctrl-0 = <&hym8563_int>; + interrupt-parent = <&gpio0>; + interrupts = ; + wakeup-source; + }; +}; + +&mdio1 { + rgmii_phy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + +&pcie2x1l1 { + reset-gpios = <&gpio1 RK_PA7 GPIO_ACTIVE_HIGH>; + vpcie3v3-supply = <&vcc_3v3_pcie20>; + status = "okay"; + + pcie@30 { + reg = <0x00300000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + + r8125_u25: pcie@30,0 { + reg = <0x000000 0 0 0 0>; + label = "eth2"; + }; + }; +}; + +&pcie2x1l2 { + reset-gpios = <&gpio3 RK_PD1 GPIO_ACTIVE_HIGH>; + vpcie3v3-supply = <&vcc_3v3_pcie20>; + status = "okay"; + + pcie@40 { + reg = <0x00400000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + + r8125_u40: pcie@40,0 { + reg = <0x000000 0 0 0 0>; + label = "eth1"; + }; + }; +}; + +&pinctrl { + gpio-leds { + lan1_led_pin: lan1-led-pin { + rockchip,pins = <1 RK_PC3 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + lan2_led_pin: lan2-led-pin { + rockchip,pins = <1 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + power_led_pin: power-led-pin { + rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + wan_led_pin: wan-led-pin { + rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + hym8563 { + hym8563_int: hym8563-int { + rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + rockchip-key { + reset_button_pin: reset-button-pin { + rockchip,pins = <1 RK_PC0 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + sdmmc { + vcc3v3_sd_en: vcc3v3-sd-en { + rockchip,pins = <4 RK_PB4 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + usb { + vbus5v0_typec_en: vbus5v0-typec-en { + rockchip,pins = <1 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + vcc5v0_host20_en: vcc5v0-host20-en { + rockchip,pins = <4 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; +}; + +&rng { + status = "okay"; +}; + +&saradc { + status = "okay"; +}; + +&sdhci { + bus-width = <8>; + cap-mmc-highspeed; + max-frequency = <200000000>; + mmc-hs200-1_8v; + no-sdio; + no-sd; + non-removable; + status = "okay"; +}; + +&sdmmc { + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + disable-wp; + max-frequency = <150000000>; + no-sdio; + no-mmc; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc_bus4 &sdmmc_clk &sdmmc_cmd &sdmmc_det>; + vmmc-supply = <&vcc_3v3_sd_s0>; + vqmmc-supply = <&vccio_sd_s0>; + status = "okay"; +}; + +&tsadc { + status = "okay"; +}; + +&uart2 { + pinctrl-0 = <&uart2m0_xfer>; + status = "okay"; +}; + +&u2phy0 { + status = "okay"; +}; + +&u2phy0_otg { + phy-supply = <&vbus5v0_typec>; + status = "okay"; +}; + +&u2phy2 { + status = "okay"; +}; + +&u2phy2_host { + phy-supply = <&vcc5v0_host_20>; + status = "okay"; +}; + +&u2phy3 { + status = "okay"; +}; + +&usbdp_phy0 { + status = "okay"; +}; + +&usbdp_phy0_u3 { + status = "okay"; +}; + +&usbdrd3_0 { + status = "okay"; +}; + +&usbdrd_dwc3_0 { + dr_mode = "host"; + extcon = <&u2phy0>; + status = "okay"; +}; + +&usb_host0_ehci { + status = "okay"; +}; + +&usb_host0_ohci { + status = "okay"; +}; diff --git a/target/linux/rockchip/image/armv8.mk b/target/linux/rockchip/image/armv8.mk index 3672215f56..bc9379130a 100644 --- a/target/linux/rockchip/image/armv8.mk +++ b/target/linux/rockchip/image/armv8.mk @@ -96,6 +96,15 @@ define Device/friendlyarm_nanopi-r5s endef TARGET_DEVICES += friendlyarm_nanopi-r5s +define Device/friendlyarm_nanopi-r6s + DEVICE_VENDOR := FriendlyARM + DEVICE_MODEL := NanoPi R6S + SOC := rk3588s + BOOT_FLOW := pine64-img + DEVICE_PACKAGES := kmod-r8125 +endef +TARGET_DEVICES += friendlyarm_nanopi-r6s + define Device/lunzn_fastrhino-r66s DEVICE_VENDOR := Lunzn DEVICE_MODEL := FastRhino R66S diff --git a/target/linux/rockchip/image/mmc.bootscript b/target/linux/rockchip/image/mmc.bootscript index 60b59e1b6b..7fb8edbd40 100644 --- a/target/linux/rockchip/image/mmc.bootscript +++ b/target/linux/rockchip/image/mmc.bootscript @@ -2,6 +2,8 @@ part uuid mmc ${devnum}:2 uuid if test $stdout = 'serial@fe660000' ; then serial_addr=',0xfe660000'; +elif test $stdout = 'serial@feb50000' ; +then serial_addr=',0xfeb50000'; elif test $stdout = 'serial@ff130000' ; then serial_addr=',0xff130000'; elif test $stdout = 'serial@ff1a0000' ; diff --git a/target/linux/rockchip/patches-6.1/900-arm64-boot-add-dts-files.patch b/target/linux/rockchip/patches-6.1/900-arm64-boot-add-dts-files.patch index 9eb84685bc..7ce686ff67 100644 --- a/target/linux/rockchip/patches-6.1/900-arm64-boot-add-dts-files.patch +++ b/target/linux/rockchip/patches-6.1/900-arm64-boot-add-dts-files.patch @@ -8,7 +8,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-r4s-enterprise.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-orangepi.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-pinebook-pro.dtb -@@ -77,6 +78,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-bp +@@ -77,9 +78,11 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-bp dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-evb1-v10.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-fastrhino-r66s.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-fastrhino-r68s.dtb @@ -16,3 +16,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-nanopi-r5c.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-nanopi-r5s.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-rock-3a.dtb + dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-evb1-v10.dtb + dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-rock-5b.dtb ++dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-nanopi-r6s.dtb + dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-rock-5a.dtb