ipq40xx: sync upstream source code
This commit is contained in:
AmadeusGhost
parent
ba890ae799
commit
ddd1ef2a31
@ -6,8 +6,8 @@ BOARDNAME:=Qualcomm Atheros IPQ40XX
|
||||
FEATURES:=squashfs fpu ramdisk nand
|
||||
CPU_TYPE:=cortex-a7
|
||||
CPU_SUBTYPE:=neon-vfpv4
|
||||
SUBTARGETS:=generic mikrotik
|
||||
MAINTAINER:=John Crispin <john@phrozen.org>
|
||||
SUBTARGETS:=generic
|
||||
|
||||
KERNEL_PATCHVER:=5.4
|
||||
|
||||
@ -17,8 +17,8 @@ include $(INCLUDE_DIR)/target.mk
|
||||
DEFAULT_PACKAGES += \
|
||||
kmod-usb-dwc3-qcom \
|
||||
kmod-leds-gpio kmod-gpio-button-hotplug swconfig \
|
||||
kmod-ath10k wpad-openssl uboot-envtools \
|
||||
kmod-usb3 kmod-usb-dwc3 ath10k-firmware-qca4019 \
|
||||
kmod-ath10k-ct wpad-openssl uboot-envtools \
|
||||
kmod-usb3 kmod-usb-dwc3 ath10k-firmware-qca4019-ct \
|
||||
autocore-arm e2fsprogs
|
||||
|
||||
$(eval $(call BuildTarget))
|
||||
|
||||
@ -43,6 +43,11 @@ century,wr142ac-nand)
|
||||
ucidef_set_led_wlan "wlan2g" "WLAN2G" "green:wlan2g" "phy0tpt"
|
||||
ucidef_set_led_wlan "wlan5g" "WLAN5G" "green:wlan5g" "phy1tpt"
|
||||
;;
|
||||
edgecore,oap100 |\
|
||||
p2w,r619ac)
|
||||
ucidef_set_led_wlan "wlan2g" "WLAN2G" "blue:wlan2g" "phy0tpt"
|
||||
ucidef_set_led_wlan "wlan5g" "WLAN5G" "blue:wlan5g" "phy1tpt"
|
||||
;;
|
||||
engenius,eap1300)
|
||||
ucidef_set_led_switch "wan" "WAN" "amber:wan" "switch0" "0x20"
|
||||
ucidef_set_led_wlan "wlan2g" "WLAN2G" "blue:wlan2g" "phy0tpt"
|
||||
@ -59,10 +64,13 @@ engenius,ens620ext)
|
||||
ucidef_set_led_switch "lan1" "LAN1" "green:lan1" "switch0" "0x10"
|
||||
ucidef_set_led_switch "lan2" "LAN2" "green:lan2" "switch0" "0x20"
|
||||
;;
|
||||
leguang,ca100)
|
||||
ucidef_set_led_default "green" "GREEN" "green:ctrl1" "1"
|
||||
ucidef_set_led_default "red" "RED" "red:ctrl2" "1"
|
||||
ucidef_set_led_default "blue" "BLUE" "blue:ctrl3" "1"
|
||||
mikrotik,sxtsq-5-ac)
|
||||
ucidef_set_rssimon "wlan0" "200000" "1"
|
||||
ucidef_set_led_rssi "rssilow" "rssilow" "green:rssilow" "wlan0" "1" "100"
|
||||
ucidef_set_led_rssi "rssimediumlow" "rssimediumlow" "green:rssimediumlow" "wlan0" "21" "100"
|
||||
ucidef_set_led_rssi "rssimedium" "rssimedium" "green:rssimedium" "wlan0" "41" "100"
|
||||
ucidef_set_led_rssi "rssimediumhigh" "rssimediumhigh" "green:rssimediumhigh" "wlan0" "61" "100"
|
||||
ucidef_set_led_rssi "rssihigh" "rssihigh" "green:rssihigh" "wlan0" "81" "100"
|
||||
;;
|
||||
mobipromo,cm520-79f)
|
||||
ucidef_set_led_switch "wan" "WAN" "blue:wan" "switch0" "0x20"
|
||||
@ -75,19 +83,12 @@ netgear,ex6200v2)
|
||||
ucidef_set_led_wlan "wlan2g" "WLAN2G" "green:router" "phy0tpt"
|
||||
ucidef_set_led_wlan "wlan5g" "WLAN5G" "green:client" "phy1tpt"
|
||||
;;
|
||||
p2w,r619ac)
|
||||
ucidef_set_led_wlan "wlan2g" "WLAN2G" "blue:wlan2g" "phy0tpt"
|
||||
ucidef_set_led_wlan "wlan5g" "WLAN5G" "blue:wlan5g" "phy1tpt"
|
||||
;;
|
||||
qxwlan,e2600ac-c1 |\
|
||||
qxwlan,e2600ac-c2)
|
||||
ucidef_set_led_wlan "wlan2g" "WLAN0" "green:wlan0" "phy0tpt"
|
||||
ucidef_set_led_wlan "wlan5g" "WLAN1" "green:wlan1" "phy1tpt"
|
||||
;;
|
||||
zyxel,nbg6617)
|
||||
ucidef_set_led_wlan "wlan2g" "WLAN2G" "green:wlan2G" "phy0tpt"
|
||||
ucidef_set_led_wlan "wlan5g" "WLAN5G" "green:wlan5G" "phy1tpt"
|
||||
;;
|
||||
zyxel,nbg6617 |\
|
||||
zyxel,wre6606)
|
||||
ucidef_set_led_wlan "wlan2g" "WLAN2G" "green:wlan2g" "phy0tpt"
|
||||
ucidef_set_led_wlan "wlan5g" "WLAN5G" "green:wlan5g" "phy1tpt"
|
||||
|
||||
@ -16,12 +16,18 @@ ipq40xx_setup_interfaces()
|
||||
8dev,jalapeno|\
|
||||
alfa-network,ap120c-ac|\
|
||||
engenius,emr3500|\
|
||||
engenius,ens620ext)
|
||||
engenius,ens620ext|\
|
||||
luma,wrtq-329acn|\
|
||||
netgear,wac510|\
|
||||
plasmacloud,pa1200|\
|
||||
plasmacloud,pa2200)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0t@eth0" "4:lan" "5:wan"
|
||||
;;
|
||||
asus,map-ac2200|\
|
||||
cilab,meshpoint-one|\
|
||||
edgecore,ecw5211|\
|
||||
edgecore,oap100|\
|
||||
openmesh,a42|\
|
||||
openmesh,a62)
|
||||
ucidef_add_switch "switch0" \
|
||||
@ -36,6 +42,8 @@ ipq40xx_setup_interfaces()
|
||||
ezviz,cs-w3-wd1200g-eup|\
|
||||
linksys,ea6350v3|\
|
||||
linksys,ea8300|\
|
||||
linksys,mr8300|\
|
||||
mikrotik,hap-ac2|\
|
||||
unielec,u4019-32m)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0t@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan"
|
||||
@ -50,7 +58,7 @@ ipq40xx_setup_interfaces()
|
||||
;;
|
||||
avm,fritzbox-7530)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0t@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
|
||||
"0u@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
|
||||
;;
|
||||
aruba,ap-303|\
|
||||
aruba,ap-365|\
|
||||
@ -58,17 +66,22 @@ ipq40xx_setup_interfaces()
|
||||
dlink,dap-2610 |\
|
||||
engenius,emd1|\
|
||||
meraki,mr33|\
|
||||
zyxel,wre6606)
|
||||
mikrotik,sxtsq-5-ac)
|
||||
ucidef_set_interface_lan "eth0"
|
||||
;;
|
||||
buffalo,wtr-m2133hp)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0u@eth0" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan"
|
||||
"0t@eth0" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan"
|
||||
;;
|
||||
cellc,rtl30vw)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0t@eth0" "3:lan" "4:lan"
|
||||
;;
|
||||
devolo,magic-2-wifi-next)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0t@eth0" "3:lan" "4:lan" "5:lan"
|
||||
;;
|
||||
glinet,gl-ap1300 |\
|
||||
glinet,gl-b1300|\
|
||||
glinet,gl-s1300|\
|
||||
qxwlan,e2600ac-c1|\
|
||||
@ -81,10 +94,6 @@ ipq40xx_setup_interfaces()
|
||||
ucidef_add_switch "switch0" \
|
||||
"0t@eth0" "2:lan" "3:lan" "4:lan" "5:wan"
|
||||
;;
|
||||
leguang,ca100)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0t@eth0" "5:wan" "3:lan"
|
||||
;;
|
||||
mobipromo,cm520-79f)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0t@eth0" "3:lan:2" "4:lan:1" "5:wan"
|
||||
@ -94,7 +103,8 @@ ipq40xx_setup_interfaces()
|
||||
ucidef_add_switch "switch0" \
|
||||
"0u@eth0" "4:lan"
|
||||
;;
|
||||
netgear,ex6200v2)
|
||||
netgear,ex6200v2|\
|
||||
zyxel,wre6606)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0t@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:lan"
|
||||
;;
|
||||
@ -118,7 +128,7 @@ ipq40xx_setup_macs()
|
||||
|
||||
case "$board" in
|
||||
8dev,habanero-dvk)
|
||||
label_mac=$(mtd_get_mac_binary "ART" 4102)
|
||||
label_mac=$(mtd_get_mac_binary "ART" 0x1006)
|
||||
;;
|
||||
asus,rt-acrh17|\
|
||||
asus,rt-ac58u)
|
||||
@ -132,7 +142,11 @@ ipq40xx_setup_macs()
|
||||
wan_mac=$(macaddr_add "$lan_mac" -1)
|
||||
;;
|
||||
cilab,meshpoint-one)
|
||||
label_mac=$(mtd_get_mac_binary "ART" 4102)
|
||||
label_mac=$(mtd_get_mac_binary "ART" 0x1006)
|
||||
;;
|
||||
devolo,magic-2-wifi-next)
|
||||
lan_mac=$(mtd_get_mac_ascii APPSBLENV MacAddress0)
|
||||
label_mac=$lan_mac
|
||||
;;
|
||||
dlink,dap-2610)
|
||||
lan_mac=$(mtd_get_mac_ascii bdcfg lanmac)
|
||||
@ -153,7 +167,7 @@ ipq40xx_setup_macs()
|
||||
lan_mac=$(macaddr_add "$wan_mac" 1)
|
||||
;;
|
||||
ezviz,cs-w3-wd1200g-eup)
|
||||
label_mac=$(mtd_get_mac_binary "ART" 6)
|
||||
label_mac=$(mtd_get_mac_binary "ART" 0x6)
|
||||
;;
|
||||
hiwifi,c526a|\
|
||||
hiwifi,c526a-128m)
|
||||
@ -168,6 +182,15 @@ ipq40xx_setup_macs()
|
||||
wan_mac=$(cat /sys/class/net/eth0/address)
|
||||
lan_mac=$(macaddr_add "$wan_mac" 1)
|
||||
;;
|
||||
mikrotik,hap-ac2)
|
||||
wan_mac=$(cat /sys/firmware/mikrotik/hard_config/mac_base)
|
||||
lan_mac=$(macaddr_add $wan_mac 1)
|
||||
label_mac="$wan_mac"
|
||||
;;
|
||||
mikrotik,sxtsq-5-ac)
|
||||
lan_mac=$(cat /sys/firmware/mikrotik/hard_config/mac_base)
|
||||
label_mac="$lan_mac"
|
||||
;;
|
||||
esac
|
||||
|
||||
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
|
||||
|
||||
@ -12,7 +12,7 @@ case "$FIRMWARE" in
|
||||
meraki,mr33)
|
||||
caldata_extract_ubi "ART" 0x9000 0x844
|
||||
caldata_valid "4408" || caldata_extract "ART" 0x9000 0x844
|
||||
ath10k_patch_mac $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 0x66) +1)
|
||||
ath10k_patch_mac $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 0x66) 1)
|
||||
;;
|
||||
esac
|
||||
;;
|
||||
@ -40,10 +40,12 @@ case "$FIRMWARE" in
|
||||
ath10k_patch_mac $(mtd_get_mac_binary ORGDATA 0x32)
|
||||
;;
|
||||
engenius,eap2200 |\
|
||||
openmesh,a62)
|
||||
openmesh,a62 |\
|
||||
plasmacloud,pa2200)
|
||||
caldata_extract "0:ART" 0x9000 0x2f20
|
||||
;;
|
||||
linksys,ea8300)
|
||||
linksys,ea8300 |\
|
||||
linksys,mr8300)
|
||||
caldata_extract "ART" 0x9000 0x2f20
|
||||
# OEM assigns 4 sequential MACs
|
||||
ath10k_patch_mac $(macaddr_setbit_la $(macaddr_add "$(cat /sys/class/net/eth0/address)" 4))
|
||||
@ -62,6 +64,7 @@ case "$FIRMWARE" in
|
||||
century,wr142ac-nand |\
|
||||
cilab,meshpoint-one |\
|
||||
ezviz,cs-w3-wd1200g-eup |\
|
||||
glinet,gl-ap1300 |\
|
||||
glinet,gl-b1300 |\
|
||||
glinet,gl-s1300 |\
|
||||
linksys,ea6350v3 |\
|
||||
@ -104,16 +107,24 @@ case "$FIRMWARE" in
|
||||
cellc,rtl30vw |\
|
||||
compex,wpj419 |\
|
||||
compex,wpj428 |\
|
||||
edgecore,ecw5211 |\
|
||||
edgecore,oap100 |\
|
||||
engenius,eap1300 |\
|
||||
engenius,eap2200 |\
|
||||
leguang,ca100 |\
|
||||
luma,wrtq-329acn|\
|
||||
openmesh,a42 |\
|
||||
openmesh,a62 |\
|
||||
plasmacloud,pa1200 |\
|
||||
plasmacloud,pa2200 |\
|
||||
qxwlan,e2600ac-c1 |\
|
||||
qxwlan,e2600ac-c2 |\
|
||||
unielec,u4019-32m)
|
||||
caldata_extract "0:ART" 0x1000 0x2f20
|
||||
;;
|
||||
devolo,magic-2-wifi-next)
|
||||
caldata_extract "ART" 0x1000 0x2f20
|
||||
ath10k_patch_mac $(mtd_get_mac_ascii APPSBLENV WiFiMacAddress0)
|
||||
;;
|
||||
dlink,dap-2610)
|
||||
caldata_extract "ART" 0x1000 0x2f20
|
||||
ath10k_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac)
|
||||
@ -128,21 +139,27 @@ case "$FIRMWARE" in
|
||||
;;
|
||||
engenius,ens620ext)
|
||||
caldata_extract "ART" 0x1000 0x2f20
|
||||
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +2)
|
||||
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) 2)
|
||||
;;
|
||||
hiwifi,c526a|\
|
||||
hiwifi,c526a-128m)
|
||||
caldata_extract "ART" 0x1000 0x2f20
|
||||
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii bdinfo "Vfac_mac ") +2)
|
||||
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii bdinfo "Vfac_mac ") 2)
|
||||
;;
|
||||
linksys,ea8300)
|
||||
linksys,ea8300 |\
|
||||
linksys,mr8300)
|
||||
caldata_extract "ART" 0x1000 0x2f20
|
||||
ath10k_patch_mac $(macaddr_add "$(cat /sys/class/net/eth0/address)" +2)
|
||||
ath10k_patch_mac $(macaddr_add "$(cat /sys/class/net/eth0/address)" 2)
|
||||
;;
|
||||
meraki,mr33)
|
||||
caldata_extract_ubi "ART" 0x1000 0x2f20
|
||||
caldata_valid "202f" || caldata_extract "ART" 0x1000 0x2f20
|
||||
ath10k_patch_mac $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 0x66) +2)
|
||||
ath10k_patch_mac $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 0x66) 2)
|
||||
;;
|
||||
mikrotik,hap-ac2)
|
||||
wlan_data="/sys/firmware/mikrotik/hard_config/wlan_data"
|
||||
( [ -f "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data" 0x0 0x2f20 ) || \
|
||||
( [ -d "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data/data_0" 0x0 0x2f20 )
|
||||
;;
|
||||
netgear,ex6100v2 |\
|
||||
netgear,ex6150v2 |\
|
||||
@ -150,6 +167,10 @@ case "$FIRMWARE" in
|
||||
caldata_extract "ART" 0x1000 0x2f20
|
||||
ath10k_patch_mac $(mtd_get_mac_binary dnidata 0x0)
|
||||
;;
|
||||
netgear,wac510)
|
||||
caldata_extract "0:ART" 0x1000 0x2f20
|
||||
ath10k_patch_mac $(mtd_get_mac_binary "0:MANUDATA" 0x6)
|
||||
;;
|
||||
zyxel,nbg6617 |\
|
||||
zyxel,wre6606)
|
||||
caldata_extract "ART" 0x1000 0x2f20
|
||||
@ -166,6 +187,7 @@ case "$FIRMWARE" in
|
||||
century,wr142ac-nand |\
|
||||
cilab,meshpoint-one |\
|
||||
ezviz,cs-w3-wd1200g-eup |\
|
||||
glinet,gl-ap1300 |\
|
||||
glinet,gl-b1300 |\
|
||||
glinet,gl-s1300 |\
|
||||
linksys,ea6350v3 |\
|
||||
@ -178,7 +200,7 @@ case "$FIRMWARE" in
|
||||
aruba,ap-303h |\
|
||||
aruba,ap-365)
|
||||
caldata_extract "ART" 0x5000 0x2f20
|
||||
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary mfginfo 0x1D) +1)
|
||||
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary mfginfo 0x1D) 1)
|
||||
;;
|
||||
asus,map-ac2200)
|
||||
caldata_extract_ubi "Factory" 0x5000 0x2f20
|
||||
@ -207,45 +229,60 @@ case "$FIRMWARE" in
|
||||
cellc,rtl30vw |\
|
||||
compex,wpj419 |\
|
||||
compex,wpj428 |\
|
||||
edgecore,ecw5211 |\
|
||||
edgecore,oap100 |\
|
||||
engenius,eap1300 |\
|
||||
hugo,ac1200 |\
|
||||
engenius,eap2200 |\
|
||||
luma,wrtq-329acn|\
|
||||
openmesh,a42 |\
|
||||
openmesh,a62 |\
|
||||
plasmacloud,pa1200 |\
|
||||
plasmacloud,pa2200 |\
|
||||
qxwlan,e2600ac-c1 |\
|
||||
qxwlan,e2600ac-c2 |\
|
||||
unielec,u4019-32m)
|
||||
caldata_extract "0:ART" 0x5000 0x2f20
|
||||
;;
|
||||
devolo,magic-2-wifi-next)
|
||||
caldata_extract "ART" 0x5000 0x2f20
|
||||
ath10k_patch_mac $(mtd_get_mac_ascii APPSBLENV WiFiMacAddress1)
|
||||
;;
|
||||
dlink,dap-2610)
|
||||
caldata_extract "ART" 0x5000 0x2f20
|
||||
ath10k_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac_a)
|
||||
;;
|
||||
engenius,emd1)
|
||||
caldata_extract "0:ART" 0x5000 0x2f20
|
||||
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii 0:APPSBLENV wlanaddr) +1)
|
||||
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii 0:APPSBLENV wlanaddr) 1)
|
||||
;;
|
||||
engenius,emr3500)
|
||||
caldata_extract "0:ART" 0x5000 0x2f20
|
||||
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii 0:APPSBLENV ethaddr) +1)
|
||||
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii 0:APPSBLENV ethaddr) 1)
|
||||
;;
|
||||
engenius,ens620ext)
|
||||
caldata_extract "ART" 0x5000 0x2f20
|
||||
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +3)
|
||||
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) 3)
|
||||
;;
|
||||
hiwifi,c526a|\
|
||||
hiwifi,c526a-128m)
|
||||
caldata_extract "ART" 0x5000 0x2f20
|
||||
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii bdinfo "Vfac_mac ") +3)
|
||||
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii bdinfo "Vfac_mac ") 3)
|
||||
;;
|
||||
linksys,ea8300)
|
||||
linksys,ea8300 |\
|
||||
linksys,mr8300)
|
||||
caldata_extract "ART" 0x5000 0x2f20
|
||||
ath10k_patch_mac $(macaddr_add "$(cat /sys/class/net/eth0/address)" +3)
|
||||
ath10k_patch_mac $(macaddr_add "$(cat /sys/class/net/eth0/address)" 3)
|
||||
;;
|
||||
meraki,mr33)
|
||||
caldata_extract_ubi "ART" 0x5000 0x2f20
|
||||
caldata_valid "202f" || caldata_extract "ART" 0x5000 0x2f20
|
||||
ath10k_patch_mac $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 0x66) +3)
|
||||
ath10k_patch_mac $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 0x66) 3)
|
||||
;;
|
||||
mikrotik,hap-ac2|\
|
||||
mikrotik,sxtsq-5-ac)
|
||||
wlan_data="/sys/firmware/mikrotik/hard_config/wlan_data"
|
||||
( [ -f "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data" 0x8000 0x2f20 ) || \
|
||||
( [ -d "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data/data_2" 0x0 0x2f20 )
|
||||
;;
|
||||
netgear,ex6100v2 |\
|
||||
netgear,ex6150v2 |\
|
||||
@ -253,6 +290,10 @@ case "$FIRMWARE" in
|
||||
caldata_extract "ART" 0x5000 0x2f20
|
||||
ath10k_patch_mac $(mtd_get_mac_binary dnidata 0xc)
|
||||
;;
|
||||
netgear,wac510)
|
||||
caldata_extract "0:ART" 0x5000 0x2f20
|
||||
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary "0:MANUDATA" 0x6) 16)
|
||||
;;
|
||||
zyxel,nbg6617 |\
|
||||
zyxel,wre6606)
|
||||
caldata_extract "ART" 0x5000 0x2f20
|
||||
|
||||
20
target/linux/ipq40xx/base-files/etc/init.d/bootcount
Executable file
20
target/linux/ipq40xx/base-files/etc/init.d/bootcount
Executable file
@ -0,0 +1,20 @@
|
||||
#!/bin/sh /etc/rc.common
|
||||
|
||||
START=99
|
||||
|
||||
boot() {
|
||||
case $(board_name) in
|
||||
alfa-network,ap120c-ac)
|
||||
[ -n "$(fw_printenv bootcount changed 2>/dev/null)" ] &&\
|
||||
echo -e "bootcount\nchanged\n" | /usr/sbin/fw_setenv -s -
|
||||
;;
|
||||
linksys,ea6350v3|\
|
||||
linksys,ea8300|\
|
||||
linksys,mr8300)
|
||||
mtd resetbc s_env || true
|
||||
;;
|
||||
netgear,wac510)
|
||||
fw_setenv boot_cnt=0
|
||||
;;
|
||||
esac
|
||||
}
|
||||
@ -1,35 +0,0 @@
|
||||
#!/bin/sh /etc/rc.common
|
||||
#
|
||||
# This script sets auto_recovery to "yes" and resets the boot counter to 0.
|
||||
# As a golden rule, this should be the latest script to run at boot. For a
|
||||
# developer snapshot, it is fine to set auto_recovery here. But for a stable
|
||||
# release, this script must in fact turn off auto_recovery.
|
||||
#
|
||||
# Why? Because the custom sysupgrade script for the device will turn on
|
||||
# auto_recovery to "yes". And it's the job of this script to set the
|
||||
# boot boot_count to 0 and then disable auto_recovery, as that condition
|
||||
# means that the stable release went well.
|
||||
#
|
||||
# I have to repeat: this script should be changed for stable releases.
|
||||
|
||||
START=99
|
||||
boot() {
|
||||
. /lib/functions.sh
|
||||
|
||||
case $(board_name) in
|
||||
linksys,ea6350v3)
|
||||
# make sure auto_recovery in uboot is always on
|
||||
IS_AUTO_RECOVERY="$(fw_printenv -n auto_recovery)"
|
||||
if [ "$IS_AUTO_RECOVERY" != "yes" ] ; then
|
||||
fw_setenv auto_recovery yes
|
||||
echo "Linksys EA6350v3: fw_setenv: auto_recovery has been set to yes"
|
||||
fi
|
||||
# reset the boot counter
|
||||
fw_setenv boot_count 0
|
||||
mtd resetbc s_env
|
||||
echo "Linksys EA6350v3: boot counter has been reset"
|
||||
echo "Linksys EA6350v3: boot_part=$(fw_printenv -n boot_part)"
|
||||
;;
|
||||
esac
|
||||
|
||||
}
|
||||
@ -3,32 +3,33 @@
|
||||
preinit_set_mac_address() {
|
||||
case $(board_name) in
|
||||
asus,map-ac2200)
|
||||
base_mac=$(mtd_get_mac_binary_ubi Factory 4102)
|
||||
ip link set dev eth0 address $(macaddr_add "$base_mac" +1)
|
||||
base_mac=$(mtd_get_mac_binary_ubi Factory 0x1006)
|
||||
ip link set dev eth0 address $(macaddr_add "$base_mac" 1)
|
||||
;;
|
||||
asus,rt-acrh17|\
|
||||
asus,rt-ac58u)
|
||||
CI_UBIPART=UBI_DEV
|
||||
base_mac=$(mtd_get_mac_binary_ubi Factory 4102)
|
||||
base_mac=$(mtd_get_mac_binary_ubi Factory 0x1006)
|
||||
ip link set dev eth0 address $(macaddr_add "$base_mac" +1)
|
||||
;;
|
||||
ezviz,cs-w3-wd1200g-eup)
|
||||
ip link set dev eth0 address $(mtd_get_mac_binary "ART" 6)
|
||||
ip link set dev eth0 address $(mtd_get_mac_binary "ART" 0x6)
|
||||
;;
|
||||
engenius,eap2200)
|
||||
base_mac=$(cat /sys/class/net/eth0/address)
|
||||
;;
|
||||
linksys,ea8300)
|
||||
linksys,ea8300|\
|
||||
linksys,mr8300)
|
||||
base_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
|
||||
ip link set dev eth0 address "${base_mac}"
|
||||
ip link set dev eth0 address "$base_mac"
|
||||
;;
|
||||
meraki,mr33)
|
||||
mac_lan=$(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 102)
|
||||
mac_lan=$(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 0x66)
|
||||
[ -n "$mac_lan" ] && ip link set dev eth0 address "$mac_lan"
|
||||
;;
|
||||
zyxel,nbg6617)
|
||||
base_mac=$(cat /sys/class/net/eth0/address)
|
||||
ip link set dev eth0 address $(macaddr_add "$base_mac" +2)
|
||||
ip link set dev eth0 address $(macaddr_add "$base_mac" 2)
|
||||
;;
|
||||
esac
|
||||
}
|
||||
|
||||
@ -8,10 +8,14 @@ set_preinit_iface() {
|
||||
ezviz,cs-w3-wd1200g-eup| \
|
||||
glinet,gl-b1300| \
|
||||
linksys,ea8300| \
|
||||
linksys,mr8300| \
|
||||
meraki,mr33| \
|
||||
zyxel,nbg6617)
|
||||
ifname=eth0
|
||||
;;
|
||||
devolo,magic-2-wifi-next)
|
||||
ifname=eth1
|
||||
;;
|
||||
esac
|
||||
}
|
||||
|
||||
|
||||
@ -1,11 +1,11 @@
|
||||
# The U-Boot loader of the OpenMesh devices requires image sizes and
|
||||
# checksums to be provided in the U-Boot environment.
|
||||
# The OpenMesh devices come with 2 main partitions - while one is active
|
||||
# The U-Boot loader with the datachk patchset for dualbooting requires image
|
||||
# sizes and checksums to be provided in the U-Boot environment.
|
||||
# The devices come with 2 main partitions - while one is active
|
||||
# sysupgrade will flash the other. The boot order is changed to boot the
|
||||
# newly flashed partition. If the new partition can't be booted due to
|
||||
# upgrade failures the previously used partition is loaded.
|
||||
|
||||
platform_do_upgrade_openmesh() {
|
||||
platform_do_upgrade_dualboot_datachk() {
|
||||
local tar_file="$1"
|
||||
local restore_backup
|
||||
local primary_kernel_mtd
|
||||
@ -44,9 +44,11 @@ platform_do_upgrade_openmesh() {
|
||||
# boot anymore to Linux until it was reflashed with ap51-flash.
|
||||
local next_boot_part="1"
|
||||
case "$(board_name)" in
|
||||
plasmacloud,pa1200|\
|
||||
openmesh,a42)
|
||||
primary_kernel_mtd=8
|
||||
;;
|
||||
plasmacloud,pa2200|\
|
||||
openmesh,a62)
|
||||
primary_kernel_mtd=10
|
||||
;;
|
||||
@ -74,7 +76,7 @@ platform_do_upgrade_openmesh() {
|
||||
#
|
||||
|
||||
# take care of restoring a saved config
|
||||
[ "$SAVE_CONFIG" -eq 1 ] && restore_backup="${MTD_CONFIG_ARGS} -j ${CONF_TAR}"
|
||||
[ -n "$UPGRADE_BACKUP" ] && restore_backup="${MTD_CONFIG_ARGS} -j ${UPGRADE_BACKUP}"
|
||||
|
||||
mtd -q erase inactive
|
||||
tar xf $tar_file ${board_dir}/root -O | mtd -n -p $kernel_length $restore_backup write - $PART_NAME
|
||||
@ -1,26 +1,50 @@
|
||||
linksys_get_target_firmware() {
|
||||
cur_boot_part=$(/usr/sbin/fw_printenv -n boot_part)
|
||||
target_firmware=""
|
||||
if [ "$cur_boot_part" = "1" ]; then
|
||||
# current primary boot - update alt boot
|
||||
target_firmware="alt_kernel"
|
||||
fw_setenv boot_part 2
|
||||
# In the Linksys EA6350v3, it is enough to set the boot_part as the boot command line is
|
||||
# bootcmd=if test $boot_part = 1; then run bootpart1; else run bootpart2; fi
|
||||
# - You probably want to use that if your device's uboot does not eval bootcmd
|
||||
#fw_setenv bootcmd "run altnandboot"
|
||||
elif [ "$cur_boot_part" = "2" ]; then
|
||||
# current alt boot - update primary boot
|
||||
target_firmware="kernel"
|
||||
fw_setenv boot_part 1
|
||||
#fw_setenv bootcmd "run nandboot"
|
||||
local cur_boot_part mtd_ubi0
|
||||
|
||||
cur_boot_part="$(/usr/sbin/fw_printenv -n boot_part)"
|
||||
if [ -z "${cur_boot_part}" ]; then
|
||||
mtd_ubi0=$(cat /sys/devices/virtual/ubi/ubi0/mtd_num)
|
||||
case "$(grep -E "^mtd${mtd_ubi0}:" /proc/mtd | cut -d '"' -f 2)" in
|
||||
kernel|rootfs)
|
||||
cur_boot_part=1
|
||||
;;
|
||||
alt_kernel|alt_rootfs)
|
||||
cur_boot_part=2
|
||||
;;
|
||||
esac
|
||||
>&2 printf "Current boot_part='%s' selected from ubi0/mtd_num='%s'" \
|
||||
"${cur_boot_part}" "${mtd_ubi0}"
|
||||
fi
|
||||
|
||||
# re-enable recovery so we get back if the new firmware is broken
|
||||
fw_setenv auto_recovery yes
|
||||
# see /etc/init.d/zlinksys_recovery
|
||||
# OEM U-Boot for EA6350v3, EA8300 and MR8300; bootcmd=
|
||||
# if test $auto_recovery = no;
|
||||
# then bootipq;
|
||||
# elif test $boot_part = 1;
|
||||
# then run bootpart1;
|
||||
# else run bootpart2;
|
||||
# fi
|
||||
|
||||
echo "$target_firmware"
|
||||
case "$cur_boot_part" in
|
||||
1)
|
||||
fw_setenv -s - <<-EOF
|
||||
boot_part 2
|
||||
auto_recovery yes
|
||||
EOF
|
||||
printf "alt_kernel"
|
||||
return
|
||||
;;
|
||||
2)
|
||||
fw_setenv -s - <<-EOF
|
||||
boot_part 1
|
||||
auto_recovery yes
|
||||
EOF
|
||||
printf "kernel"
|
||||
return
|
||||
;;
|
||||
*)
|
||||
return
|
||||
;;
|
||||
esac
|
||||
}
|
||||
|
||||
linksys_get_root_magic() {
|
||||
@ -30,16 +54,19 @@ linksys_get_root_magic() {
|
||||
platform_do_upgrade_linksys() {
|
||||
local magic_long="$(get_magic_long "$1")"
|
||||
|
||||
local rm_oem_fw_vols="squashfs ubifs" # from OEM [alt_]rootfs UBI
|
||||
local vol
|
||||
|
||||
mkdir -p /var/lock
|
||||
local part_label="$(linksys_get_target_firmware)"
|
||||
touch /var/lock/fw_printenv.lock
|
||||
|
||||
if [ ! -n "$part_label" ]; then
|
||||
if [ -z "$part_label" ]; then
|
||||
echo "cannot find target partition"
|
||||
exit 1
|
||||
fi
|
||||
|
||||
local target_mtd=$(find_mtd_part $part_label)
|
||||
local target_mtd=$(find_mtd_part "$part_label")
|
||||
|
||||
[ "$magic_long" = "73797375" ] && {
|
||||
CI_KERNPART="$part_label"
|
||||
@ -49,47 +76,47 @@ platform_do_upgrade_linksys() {
|
||||
CI_UBIPART="alt_rootfs"
|
||||
fi
|
||||
|
||||
# remove "squashfs" vol (in case we are flashing over a stock image, which is also UBI)
|
||||
|
||||
local mtdnum="$( find_mtd_index "$CI_UBIPART" )"
|
||||
local mtdnum="$(find_mtd_index "$CI_UBIPART")"
|
||||
if [ ! "$mtdnum" ]; then
|
||||
echo "cannot find ubi mtd partition $CI_UBIPART"
|
||||
return 1
|
||||
fi
|
||||
|
||||
local ubidev="$( nand_find_ubi "$CI_UBIPART" )"
|
||||
local ubidev="$(nand_find_ubi "$CI_UBIPART")"
|
||||
if [ ! "$ubidev" ]; then
|
||||
ubiattach -m "$mtdnum"
|
||||
sync
|
||||
ubidev="$( nand_find_ubi "$CI_UBIPART" )"
|
||||
ubidev="$(nand_find_ubi "$CI_UBIPART")"
|
||||
fi
|
||||
|
||||
if [ "$ubidev" ]; then
|
||||
local squash_ubivol="$( nand_find_volume $ubidev squashfs )"
|
||||
# kill volume
|
||||
[ "$squash_ubivol" ] && ubirmvol /dev/$ubidev -N squashfs || true
|
||||
for vol in $rm_oem_fw_vols; do
|
||||
ubirmvol "/dev/$ubidev" -N "$vol" 2>/dev/null
|
||||
done
|
||||
fi
|
||||
|
||||
# complete std upgrade
|
||||
nand_upgrade_tar "$1"
|
||||
}
|
||||
|
||||
[ "$magic_long" = "27051956" ] && {
|
||||
# This magic is for a uImage (which is a sysupgrade image)
|
||||
# check firmwares' rootfs types
|
||||
local oldroot="$(linksys_get_root_magic $target_mtd)"
|
||||
local oldroot="$(linksys_get_root_magic "$target_mtd")"
|
||||
local newroot="$(linksys_get_root_magic "$1")"
|
||||
|
||||
if [ "$newroot" = "55424923" -a "$oldroot" = "55424923" ]; then
|
||||
if [ "$newroot" = "55424923" ] && [ "$oldroot" = "55424923" ]; then
|
||||
# we're upgrading from a firmware with UBI to one with UBI
|
||||
# erase everything to be safe
|
||||
# - Is that really needed? Won't remove (or comment) the if, because it may be needed in a future device.
|
||||
# - Is that really needed? Won't remove (or comment) the if,
|
||||
# because it may be needed in a future device.
|
||||
#mtd erase $part_label
|
||||
#get_image "$1" | mtd -n write - $part_label
|
||||
echo "writing \"$1\" UBI image to \"$part_label\" (UBI)..."
|
||||
get_image "$1" | mtd write - $part_label
|
||||
get_image "$1" | mtd write - "$part_label"
|
||||
else
|
||||
echo "writing \"$1\" image to \"$part_label\""
|
||||
get_image "$1" | mtd write - $part_label
|
||||
get_image "$1" | mtd write - "$part_label"
|
||||
fi
|
||||
}
|
||||
}
|
||||
|
||||
@ -180,9 +180,15 @@ platform_do_upgrade() {
|
||||
buffalo,wtr-m2133hp |\
|
||||
century,wr142ac-nand |\
|
||||
cilab,meshpoint-one |\
|
||||
edgecore,ecw5211 |\
|
||||
edgecore,oap100 |\
|
||||
engenius,eap2200 |\
|
||||
glinet,gl-ap1300 |\
|
||||
hiwifi,c526a |\
|
||||
hiwifi,c526a-128m |\
|
||||
luma,wrtq-329acn |\
|
||||
mobipromo,cm520-79f |\
|
||||
netgear,wac510 |\
|
||||
qxwlan,e2600ac-c2)
|
||||
nand_do_upgrade "$ARGV"
|
||||
;;
|
||||
@ -222,17 +228,25 @@ platform_do_upgrade() {
|
||||
nand_do_upgrade "$1"
|
||||
;;
|
||||
linksys,ea6350v3 |\
|
||||
linksys,ea8300)
|
||||
linksys,ea8300 |\
|
||||
linksys,mr8300)
|
||||
platform_do_upgrade_linksys "$1"
|
||||
;;
|
||||
meraki,mr33)
|
||||
CI_KERNPART="part.safe"
|
||||
nand_do_upgrade "$1"
|
||||
;;
|
||||
mikrotik,hap-ac2|\
|
||||
mikrotik,sxtsq-5-ac)
|
||||
[ "$(rootfs_type)" = "tmpfs" ] && mtd erase firmware
|
||||
default_do_upgrade "$1"
|
||||
;;
|
||||
openmesh,a42 |\
|
||||
openmesh,a62)
|
||||
openmesh,a62 |\
|
||||
plasmacloud,pa1200 |\
|
||||
plasmacloud,pa2200)
|
||||
PART_NAME="inactive"
|
||||
platform_do_upgrade_openmesh "$ARGV"
|
||||
platform_do_upgrade_dualboot_datachk "$1"
|
||||
;;
|
||||
zyxel,nbg6617)
|
||||
zyxel_do_upgrade "$1"
|
||||
|
||||
@ -182,7 +182,7 @@ CONFIG_GPIOLIB=y
|
||||
CONFIG_GPIOLIB_IRQCHIP=y
|
||||
CONFIG_GPIO_74X164=y
|
||||
CONFIG_GPIO_WATCHDOG=y
|
||||
# CONFIG_GPIO_WATCHDOG_ARCH_INITCALL is not set
|
||||
CONFIG_GPIO_WATCHDOG_ARCH_INITCALL=y
|
||||
CONFIG_HANDLE_DOMAIN_IRQ=y
|
||||
CONFIG_HARDEN_BRANCH_PREDICTOR=y
|
||||
CONFIG_HARDIRQS_SW_RESEND=y
|
||||
@ -457,7 +457,6 @@ CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h"
|
||||
CONFIG_UNWINDER_ARM=y
|
||||
CONFIG_USB=y
|
||||
CONFIG_USB_COMMON=y
|
||||
# CONFIG_USB_EHCI_HCD is not set
|
||||
CONFIG_USB_SUPPORT=y
|
||||
CONFIG_USE_OF=y
|
||||
CONFIG_VFP=y
|
||||
|
||||
@ -0,0 +1,311 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
model = "Edgecore ECW5211";
|
||||
compatible = "edgecore,ecw5211";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power;
|
||||
led-failsafe = &led_power;
|
||||
led-running = &led_power;
|
||||
led-upgrade = &led_power;
|
||||
label-mac-device = &gmac0;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs-append = " root=/dev/ubiblock0_1";
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power: power {
|
||||
label = "yellow:power";
|
||||
gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wlan2g {
|
||||
label = "green:wlan2g";
|
||||
gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
wlan5g {
|
||||
label = "green:wlan5g";
|
||||
gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
};
|
||||
|
||||
soc {
|
||||
rng@22000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-psgmii@98000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
counter@4a1000 {
|
||||
compatible = "qcom,qca-gcnt";
|
||||
reg = <0x4a1000 0x4>;
|
||||
};
|
||||
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
tcsr@194b000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x194b000 0x100>;
|
||||
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
usb2@60f8800 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
usb3@8af8800 {
|
||||
status = "okay";
|
||||
|
||||
dwc3@8a00000 {
|
||||
phys = <&usb3_hs_phy>;
|
||||
phy-names = "usb2-phy";
|
||||
};
|
||||
};
|
||||
|
||||
crypto@8e3a000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog@b017000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-switch@c000000 {
|
||||
status = "okay";
|
||||
|
||||
switch_lan_bmp = <0x10>;
|
||||
switch_wan_bmp = <0x20>;
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
mdio_pins: mdio_pinmux {
|
||||
mux_mdio {
|
||||
pins = "gpio53";
|
||||
function = "mdio";
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
mux_mdc {
|
||||
pins = "gpio52";
|
||||
function = "mdc";
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
serial_pins: serial_pinmux {
|
||||
mux {
|
||||
pins = "gpio60", "gpio61";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
spi0_pins: spi0_pinmux {
|
||||
pin {
|
||||
function = "blsp_spi0";
|
||||
pins = "gpio55", "gpio56", "gpio57";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
pin_cs {
|
||||
function = "gpio";
|
||||
pins = "gpio54", "gpio4";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
|
||||
i2c0_pins: i2c0_pinmux {
|
||||
mux_i2c {
|
||||
function = "blsp_i2c0";
|
||||
pins = "gpio58", "gpio59";
|
||||
drive-strength = <16>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&spi0_pins>;
|
||||
pinctrl-names = "default";
|
||||
cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, <&tlmm 4 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <24000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "0:SBL1";
|
||||
reg = <0x00000000 0x00040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "0:MIBIB";
|
||||
reg = <0x00040000 0x00020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@60000 {
|
||||
label = "0:QSEE";
|
||||
reg = <0x00060000 0x00060000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@c0000 {
|
||||
label = "0:CDT";
|
||||
reg = <0x000c0000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@d0000 {
|
||||
label = "0:DDRPARAMS";
|
||||
reg = <0x000d0000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@e0000 {
|
||||
label = "0:APPSBLENV"; /* uboot env */
|
||||
reg = <0x000e0000 0x00010000>;
|
||||
};
|
||||
|
||||
partition@f0000 {
|
||||
label = "0:APPSBL"; /* uboot */
|
||||
reg = <0x000f0000 0x00080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@170000 {
|
||||
label = "0:ART";
|
||||
reg = <0x00170000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
flash@1 {
|
||||
compatible = "spi-nand";
|
||||
reg = <1>;
|
||||
spi-max-frequency = <24000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "rootfs";
|
||||
reg = <0x00000000 0x04000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_i2c3 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&i2c0_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
tpm@29 {
|
||||
compatible = "atmel,at97sc3204t";
|
||||
reg = <0x29>;
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&serial_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mdio {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
|
||||
qcom,ath10k-calibration-variant = "ALFA-Network-AP120C-AC";
|
||||
};
|
||||
|
||||
&usb3_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb2_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
@ -0,0 +1,269 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
model = "GL.iNet GL-AP1300";
|
||||
compatible = "glinet,gl-ap1300";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power;
|
||||
led-failsafe = &led_power;
|
||||
led-running = &led_power;
|
||||
led-upgrade = &led_power;
|
||||
};
|
||||
|
||||
memory {
|
||||
device_type = "memory";
|
||||
reg = <0x80000000 0x10000000>;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs-append = " ubi.mtd=ubi root=/dev/ubiblock0_1 clk_ignore_unused";
|
||||
};
|
||||
|
||||
soc {
|
||||
rng@22000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
mdio@90000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-psgmii@98000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
tcsr@194b000 {
|
||||
/* select hostmode */
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x194b000 0x100>;
|
||||
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
usb2@60f8800 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
usb3@8af8800 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
crypto@8e3a000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog@b017000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-switch@c000000 {
|
||||
status = "okay";
|
||||
switch_lan_bmp = <0x18>;
|
||||
switch_wan_bmp = <0x20>;
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power: power {
|
||||
label = "green:power";
|
||||
gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
wan {
|
||||
label = "green:wan";
|
||||
gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&spi0_pins>;
|
||||
pinctrl-names = "default";
|
||||
cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, <&tlmm 5 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
flash@0 {
|
||||
status = "okay";
|
||||
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <24000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "SBL1";
|
||||
reg = <0x00000000 0x00040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "MIBIB";
|
||||
reg = <0x00040000 0x00020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@60000 {
|
||||
label = "QSEE";
|
||||
reg = <0x00060000 0x00060000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@c0000 {
|
||||
label = "CDT";
|
||||
reg = <0x000c0000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@d0000 {
|
||||
label = "DDRPARAMS";
|
||||
reg = <0x000d0000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@e0000 {
|
||||
label = "APPSBLENV"; /* uboot env*/
|
||||
reg = <0x000e0000 0x00010000>;
|
||||
};
|
||||
|
||||
partition@f0000 {
|
||||
label = "APPSBL"; /* uboot */
|
||||
reg = <0x000f0000 0x00080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@170000 {
|
||||
label = "ART";
|
||||
reg = <0x00170000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
spi-nand@1 {
|
||||
status = "okay";
|
||||
|
||||
compatible = "spi-nand";
|
||||
reg = <1>;
|
||||
spi-max-frequency = <24000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "ubi";
|
||||
reg = <0x00000000 0x08000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
pinctrl-0 = <&serial_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
serial_pins: serial_pinmux {
|
||||
mux {
|
||||
pins = "gpio60", "gpio61";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
spi0_pins: spi0_pinmux {
|
||||
mux_spi {
|
||||
function = "blsp_spi0";
|
||||
pins = "gpio55", "gpio56", "gpio57";
|
||||
drive-strength = <12>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
mux_cs {
|
||||
function = "gpio";
|
||||
pins = "gpio54", "gpio5";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb2_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_ss_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
qcom,ath10k-calibration-variant = "GL-AP1300";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
qcom,ath10k-calibration-variant = "GL-AP1300";
|
||||
};
|
||||
@ -0,0 +1,273 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/* Copyright (c) 2020, Robert Marko <robimarko@gmail.com> */
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
model = "MikroTik hAP ac2";
|
||||
compatible = "mikrotik,hap-ac2";
|
||||
|
||||
memory {
|
||||
device_type = "memory";
|
||||
reg = <0x80000000 0x08000000>;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &led_user;
|
||||
led-failsafe = &led_user;
|
||||
led-running = &led_user;
|
||||
led-upgrade = &led_user;
|
||||
};
|
||||
|
||||
soc {
|
||||
rng@22000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
counter@4a1000 {
|
||||
compatible = "qcom,qca-gcnt";
|
||||
reg = <0x4a1000 0x4>;
|
||||
};
|
||||
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
tcsr@194b000 {
|
||||
/* select hostmode */
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x194b000 0x100>;
|
||||
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
usb3@8af8800 {
|
||||
status = "okay";
|
||||
|
||||
dwc3@8a00000 {
|
||||
phys = <&usb3_hs_phy>;
|
||||
phy-names = "usb2-phy";
|
||||
};
|
||||
};
|
||||
|
||||
crypto@8e3a000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog@b017000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-switch@c000000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
mode {
|
||||
label = "mode";
|
||||
gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RFKILL>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
power {
|
||||
label = "green:power";
|
||||
gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "keep";
|
||||
panic-indicator;
|
||||
};
|
||||
|
||||
led_user: user {
|
||||
label = "green:user";
|
||||
gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
serial_pins: serial_pinmux {
|
||||
mux {
|
||||
pins = "gpio60", "gpio61";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
spi_0_pins: spi_0_pinmux {
|
||||
pin {
|
||||
function = "blsp_spi0";
|
||||
pins = "gpio55", "gpio56", "gpio57";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
};
|
||||
pin_cs {
|
||||
function = "gpio";
|
||||
pins = "gpio54";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
|
||||
enable-usb-power {
|
||||
gpio-hog;
|
||||
gpios = <2 GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
line-name = "enable USB power";
|
||||
};
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
flash@0 {
|
||||
reg = <0>;
|
||||
compatible = "jedec,spi-nor";
|
||||
spi-max-frequency = <40000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "Qualcomm";
|
||||
reg = <0x0 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
compatible = "mikrotik,routerboot-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
label = "RouterBoot";
|
||||
reg = <0x80000 0x80000>;
|
||||
read-only;
|
||||
|
||||
hard_config {
|
||||
read-only;
|
||||
size = <0x2000>;
|
||||
};
|
||||
|
||||
dtb_config {
|
||||
read-only;
|
||||
};
|
||||
|
||||
soft_config {
|
||||
};
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
compatible = "mikrotik,minor";
|
||||
label = "firmware";
|
||||
reg = <0x100000 0xf00000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&serial_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mdio {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ðphy0 {
|
||||
qcom,single-led-1000;
|
||||
qcom,single-led-100;
|
||||
qcom,single-led-10;
|
||||
};
|
||||
|
||||
ðphy1 {
|
||||
qcom,single-led-1000;
|
||||
qcom,single-led-100;
|
||||
qcom,single-led-10;
|
||||
};
|
||||
|
||||
ðphy2 {
|
||||
qcom,single-led-1000;
|
||||
qcom,single-led-100;
|
||||
qcom,single-led-10;
|
||||
};
|
||||
|
||||
ðphy3 {
|
||||
qcom,single-led-1000;
|
||||
qcom,single-led-100;
|
||||
qcom,single-led-10;
|
||||
};
|
||||
|
||||
ðphy4 {
|
||||
qcom,single-led-1000;
|
||||
qcom,single-led-100;
|
||||
qcom,single-led-10;
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
|
||||
qcom,ath10k-calibration-variant = "MikroTik-hAP-ac2";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
|
||||
qcom,ath10k-calibration-variant = "MikroTik-hAP-ac2";
|
||||
};
|
||||
@ -0,0 +1,251 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
model = "devolo Magic 2 WiFi next";
|
||||
compatible = "devolo,magic-2-wifi-next";
|
||||
|
||||
memory {
|
||||
device_type = "memory";
|
||||
reg = <0x80000000 0x10000000>;
|
||||
};
|
||||
|
||||
soc {
|
||||
rng@22000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
mdio@90000 {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
pinctrl-names = "default";
|
||||
reset-gpios = <&tlmm 59 GPIO_ACTIVE_LOW>;
|
||||
reset-delay-us = <2000>;
|
||||
|
||||
/delete-node/ ethernet-phy@0;
|
||||
/delete-node/ ethernet-phy@1;
|
||||
};
|
||||
|
||||
ess-psgmii@98000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
crypto@8e3a000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog@b017000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-switch@c000000 {
|
||||
status = "okay";
|
||||
switch_lan_bmp = <0x3e>;
|
||||
switch_wan_bmp = <0x0>;
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
qcom,num_gmac = <1>;
|
||||
};
|
||||
|
||||
gpio_export {
|
||||
compatible = "gpio-export";
|
||||
#size-cells = <0>;
|
||||
|
||||
plc {
|
||||
gpio-export,name = "plc-enable";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&tlmm 63 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
wlan {
|
||||
label = "WLAN";
|
||||
gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "Reset";
|
||||
gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
status_dlan {
|
||||
label = "white:dlan";
|
||||
gpios = <&tlmm 4 GPIO_ACTIVE_LOW>;
|
||||
default-state = "keep";
|
||||
};
|
||||
|
||||
status_wlan {
|
||||
label = "white:wlan";
|
||||
gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
|
||||
default-state = "keep";
|
||||
};
|
||||
|
||||
error_dlan {
|
||||
label = "red:dlan";
|
||||
gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "keep";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
spi_0_pins: spi_0_pinmux {
|
||||
mux {
|
||||
function = "blsp_spi0";
|
||||
pins = "gpio55", "gpio56", "gpio57";
|
||||
drive-strength = <12>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
mux_cs {
|
||||
function = "gpio";
|
||||
pins = "gpio54";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
|
||||
mdio_pins: mdio_pinmux {
|
||||
mux_1 {
|
||||
pins = "gpio53";
|
||||
function = "mdio";
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
mux_2 {
|
||||
pins = "gpio52";
|
||||
function = "mdc";
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
serial_pins: serial_pinmux {
|
||||
mux {
|
||||
pins = "gpio61", "gpio60";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
button_pins: button_pinmux {
|
||||
mux {
|
||||
function = "gpio";
|
||||
pins = "gpio0", "gpio5";
|
||||
bias-disable;
|
||||
input;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
pinctrl-0 = <&serial_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
qcom,ath10k-calibration-variant = "devolo,magic-2-wifi-next";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
qcom,ath10k-calibration-variant = "devolo,magic-2-wifi-next";
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
linux,modalias = "n25q128a11";
|
||||
spi-max-frequency = <24000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "SBL1";
|
||||
reg = <0x00000000 0x00040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "MIBIB";
|
||||
reg = <0x00040000 0x00020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@60000 {
|
||||
label = "QSEE";
|
||||
reg = <0x00060000 0x00060000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@c0000 {
|
||||
label = "CDT";
|
||||
reg = <0x000c0000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@d0000 {
|
||||
label = "DDRPARAMS";
|
||||
reg = <0x000d0000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@e0000 {
|
||||
label = "APPSBLENV"; /* uboot env*/
|
||||
reg = <0x000e0000 0x00010000>;
|
||||
};
|
||||
|
||||
partition@f0000 {
|
||||
label = "APPSBL"; /* uboot */
|
||||
reg = <0x000f0000 0x00080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@170000 {
|
||||
label = "ART";
|
||||
reg = <0x00170000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
firmware@180000 {
|
||||
compatible = "denx,fit";
|
||||
label = "firmware";
|
||||
reg = <0x00180000 0x01a80000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
@ -0,0 +1,197 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/* Copyright (c) 2017-2020, Sven Eckelmann <sven@narfation.org>
|
||||
* Copyright (c) 2018, Marek Lindner <marek.lindner@kaiwoo.ai>
|
||||
*/
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
model = "Plasma Cloud PA1200";
|
||||
compatible = "plasmacloud,pa1200";
|
||||
|
||||
soc {
|
||||
rng@22000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
mdio@90000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-psgmii@98000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
tcsr@194b000 {
|
||||
/* select hostmode */
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x194b000 0x100>;
|
||||
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
usb2: usb2@60f8800 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
crypto@8e3a000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog@b017000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-switch@c000000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 59 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &led_status_purple;
|
||||
led-failsafe = &led_status_yellow;
|
||||
led-running = &led_status_cyan;
|
||||
led-upgrade = &led_status_yellow;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_status_cyan: status_cyan {
|
||||
label = "cyan:status";
|
||||
gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_status_purple: status_purple {
|
||||
label = "purple:status";
|
||||
gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_status_yellow: status_yellow {
|
||||
label = "yellow:status";
|
||||
gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
serial_pins: serial_pinmux {
|
||||
mux {
|
||||
pins = "gpio60", "gpio61";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
spi_0_pins: spi_0_pinmux {
|
||||
pin {
|
||||
function = "blsp_spi0";
|
||||
pins = "gpio55", "gpio56", "gpio57";
|
||||
drive-strength = <12>;
|
||||
bias-disable;
|
||||
};
|
||||
pin_cs {
|
||||
function = "gpio";
|
||||
pins = "gpio54";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
flash@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <24000000>;
|
||||
/* partitions are passed via bootloader */
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
pinctrl-0 = <&serial_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
qcom,phy_mdio_addr = <4>;
|
||||
qcom,poll_required = <1>;
|
||||
qcom,forced_speed = <1000>;
|
||||
qcom,forced_duplex = <1>;
|
||||
vlan_tag = <2 0x20>;
|
||||
};
|
||||
|
||||
&gmac1 {
|
||||
qcom,phy_mdio_addr = <3>;
|
||||
qcom,poll_required = <1>;
|
||||
qcom,forced_speed = <1000>;
|
||||
qcom,forced_duplex = <1>;
|
||||
vlan_tag = <1 0x10>;
|
||||
};
|
||||
|
||||
&usb2_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
qcom,ath10k-calibration-variant = "PlasmaCloud-PA1200";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
qcom,ath10k-calibration-variant = "PlasmaCloud-PA1200";
|
||||
};
|
||||
@ -0,0 +1,242 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/* Copyright (c) 2020, Robert Marko <robimarko@gmail.com> */
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
model = "MikroTik SXTsq 5 ac (RBSXTsqG-5acD)";
|
||||
compatible = "mikrotik,sxtsq-5-ac";
|
||||
|
||||
memory {
|
||||
device_type = "memory";
|
||||
reg = <0x80000000 0x10000000>;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &led_user;
|
||||
led-failsafe = &led_user;
|
||||
led-running = &led_user;
|
||||
led-upgrade = &led_user;
|
||||
};
|
||||
|
||||
soc {
|
||||
rng@22000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
mdio@90000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
counter@4a1000 {
|
||||
compatible = "qcom,qca-gcnt";
|
||||
reg = <0x4a1000 0x4>;
|
||||
};
|
||||
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
crypto@8e3a000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog@b017000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-psgmii@98000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
phy-mode = "rgmii";
|
||||
qcom,num_gmac = <1>;
|
||||
qcom,single-phy;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
power {
|
||||
label = "blue:power";
|
||||
gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "keep";
|
||||
panic-indicator;
|
||||
};
|
||||
|
||||
led_user: user {
|
||||
label = "green:user";
|
||||
gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
rssilow {
|
||||
label = "green:rssilow";
|
||||
gpios = <&tlmm 58 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
rssimediumlow {
|
||||
label = "green:rssimediumlow";
|
||||
gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
rssimedium {
|
||||
label = "green:rssimedium";
|
||||
gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
rssimediumhigh {
|
||||
label = "green:rssimediumhigh";
|
||||
gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
rssihigh {
|
||||
label = "green:rssihigh";
|
||||
gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
serial_pins: serial_pinmux {
|
||||
mux {
|
||||
pins = "gpio60", "gpio61";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
spi_0_pins: spi_0_pinmux {
|
||||
pin {
|
||||
function = "blsp_spi0";
|
||||
pins = "gpio55", "gpio56", "gpio57";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
};
|
||||
pin_cs {
|
||||
function = "gpio";
|
||||
pins = "gpio54";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
flash@0 {
|
||||
reg = <0>;
|
||||
compatible = "jedec,spi-nor";
|
||||
spi-max-frequency = <40000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "Qualcomm";
|
||||
reg = <0x0 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
compatible = "mikrotik,routerboot-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
label = "RouterBoot";
|
||||
reg = <0x80000 0x80000>;
|
||||
read-only;
|
||||
|
||||
hard_config {
|
||||
read-only;
|
||||
};
|
||||
|
||||
dtb_config {
|
||||
read-only;
|
||||
};
|
||||
|
||||
soft_config {
|
||||
};
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
compatible = "mikrotik,minor";
|
||||
label = "firmware";
|
||||
reg = <0x100000 0xf00000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&serial_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
|
||||
qcom,ath10k-calibration-variant = "MikroTik-SXTsq-5-ac";
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
qcom,phy_mdio_addr = <4>;
|
||||
qcom,poll_required = <1>;
|
||||
qcom,forced_speed = <1000>;
|
||||
qcom,forced_duplex = <1>;
|
||||
vlan_tag = <1 0x20>;
|
||||
};
|
||||
|
||||
&mdio {
|
||||
status = "okay";
|
||||
};
|
||||
@ -0,0 +1,371 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/* Copyright (c) 2020, Robert Marko <robimarko@gmail.com> */
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
model = "Netgear WAC510";
|
||||
compatible = "netgear,wac510";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power_amber;
|
||||
led-failsafe = &led_power_amber;
|
||||
led-running = &led_power_green;
|
||||
led-upgrade = &led_power_amber;
|
||||
label-mac-device = &gmac0;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs-append = " root=/dev/ubiblock0_1";
|
||||
};
|
||||
|
||||
soc {
|
||||
rng@22000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-psgmii@98000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
counter@4a1000 {
|
||||
compatible = "qcom,qca-gcnt";
|
||||
reg = <0x4a1000 0x4>;
|
||||
};
|
||||
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
tcsr@194b000 {
|
||||
status = "okay";
|
||||
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x194b000 0x100>;
|
||||
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
usb2: usb2@60f8800 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
usb3: usb3@8af8800 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
crypto@8e3a000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog@b017000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-switch@c000000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
led_spi {
|
||||
compatible = "spi-gpio";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
sck-gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
|
||||
mosi-gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>;
|
||||
num-chipselects = <0>;
|
||||
|
||||
ssr: ssr@0 {
|
||||
compatible = "fairchild,74hc595";
|
||||
reg = <0>;
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
registers-number = <1>;
|
||||
spi-max-frequency = <1000000>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power_amber: power_amber {
|
||||
label = "amber:power";
|
||||
gpios = <&ssr 6 GPIO_ACTIVE_LOW>;
|
||||
panic-indicator;
|
||||
};
|
||||
|
||||
led_power_green: power_green {
|
||||
label = "green:power";
|
||||
gpios = <&ssr 5 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wlan2g_blue {
|
||||
label = "blue:wlan2g";
|
||||
gpios = <&ssr 4 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
wlan2g_green {
|
||||
label = "green:wlan2g";
|
||||
gpios = <&ssr 3 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0radio";
|
||||
};
|
||||
|
||||
wlan5g_blue {
|
||||
label = "blue:wlan5g";
|
||||
gpios = <&ssr 2 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
|
||||
wlan5g_green {
|
||||
label = "green:wlan5g";
|
||||
gpios = <&ssr 1 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1radio";
|
||||
};
|
||||
|
||||
act_green {
|
||||
label = "green:act";
|
||||
gpios = <&ssr 0 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
mdio_pins: mdio_pinmux {
|
||||
mux_1 {
|
||||
pins = "gpio53";
|
||||
function = "mdio";
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
mux_2 {
|
||||
pins = "gpio52";
|
||||
function = "mdc";
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
serial_pins: serial_pinmux {
|
||||
mux {
|
||||
pins = "gpio60", "gpio61";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
spi_0_pins: spi_0_pinmux {
|
||||
pinmux {
|
||||
function = "blsp_spi0";
|
||||
pins = "gpio55", "gpio56", "gpio57";
|
||||
drive-strength = <12>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
pinmux_cs {
|
||||
function = "gpio";
|
||||
pins = "gpio54", "gpio59";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>,
|
||||
<&tlmm 59 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
spi-max-frequency = <50000000>;
|
||||
reg = <0>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "0:SBL1";
|
||||
reg = <0x00000000 0x00040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "0:MIBIB";
|
||||
reg = <0x00040000 0x00020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@60000 {
|
||||
label = "0:QSEE";
|
||||
reg = <0x00060000 0x00060000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@c0000 {
|
||||
label = "0:CDT";
|
||||
reg = <0x000c0000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@d0000 {
|
||||
label = "0:DDRPARAMS";
|
||||
reg = <0x000d0000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@e0000 {
|
||||
label = "0:APPSBLENV";
|
||||
reg = <0x000e0000 0x00010000>;
|
||||
};
|
||||
|
||||
partition@f0000 {
|
||||
label = "0:APPSBL";
|
||||
reg = <0x000f0000 0x000f0000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1e0000 {
|
||||
label = "0:MANUDATA";
|
||||
reg = <0x001e0000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1f0000 {
|
||||
label = "0:ART";
|
||||
reg = <0x001f0000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
nand@1 {
|
||||
compatible = "spi-nand";
|
||||
reg = <1>;
|
||||
spi-max-frequency = <48000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "rootfs";
|
||||
reg = <0x00000000 0x03800000>;
|
||||
};
|
||||
|
||||
partition@3800000 {
|
||||
label = "rootfs_1";
|
||||
reg = <0x03800000 0x03800000>;
|
||||
};
|
||||
|
||||
partition@7000000 {
|
||||
label = "var_config";
|
||||
reg = <0x07000000 0x00f00000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@7f00000 {
|
||||
label = "Oops_log";
|
||||
reg = <0x07f00000 0x000c0000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&serial_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mdio {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
pinctrl-names = "default";
|
||||
reset-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
|
||||
reset-delay-us = <2000>;
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
qcom,forced_duplex = <1>;
|
||||
qcom,forced_speed = <1000>;
|
||||
qcom,phy_mdio_addr = <3>;
|
||||
qcom,poll_required = <1>;
|
||||
vlan_tag = <1 0x10>;
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
|
||||
qcom,ath10k-calibration-variant = "Netgear-WAC510";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
|
||||
qcom,ath10k-calibration-variant = "Netgear-WAC510";
|
||||
};
|
||||
|
||||
&usb3_ss_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb2_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
@ -0,0 +1,275 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
model = "Luma Home WRTQ-329ACN";
|
||||
compatible = "luma,wrtq-329acn";
|
||||
|
||||
i2c-gpio {
|
||||
compatible = "i2c-gpio";
|
||||
sda-gpios = <&tlmm 1 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
||||
scl-gpios = <&tlmm 0 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
/* No driver exists */
|
||||
led_ring@48 {
|
||||
compatible = "ti,msp430";
|
||||
reg = <0x48>;
|
||||
};
|
||||
|
||||
eeprom@50 {
|
||||
compatible = "atmel,24c16";
|
||||
reg = <0x50>;
|
||||
pagesize = <16>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
soc {
|
||||
rng@22000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
mdio@90000 {
|
||||
status = "okay";
|
||||
|
||||
/delete-node/ ethernet-phy@0;
|
||||
/delete-node/ ethernet-phy@1;
|
||||
/delete-node/ ethernet-phy@3;
|
||||
};
|
||||
|
||||
ess-psgmii@98000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
tcsr@194b000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x194b000 0x100>;
|
||||
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
usb2@60f8800 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
usb3@8af8800 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
crypto@8e3a000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog@b017000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-switch@c000000 {
|
||||
status = "okay";
|
||||
|
||||
switch_lan_bmp = <0x1e>;
|
||||
switch_wan_bmp = <0x20>;
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
|
||||
&blsp1_spi1 {
|
||||
status = "okay";
|
||||
|
||||
cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>,
|
||||
<&tlmm 59 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-0 = <&spi0_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <24000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "0:SBL1";
|
||||
reg = <0x000000 0x040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "0:MIBIB";
|
||||
reg = <0x040000 0x020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@60000 {
|
||||
label = "0:QSEE";
|
||||
reg = <0x060000 0x060000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@c0000 {
|
||||
label = "0:CDT";
|
||||
reg = <0x0c0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@d0000 {
|
||||
label = "0:DDRPARAMS";
|
||||
reg = <0x0d0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@e0000 {
|
||||
label = "0:APPSBLENV";
|
||||
reg = <0x0e0000 0x010000>;
|
||||
};
|
||||
|
||||
partition@f0000 {
|
||||
label = "0:APPSBL";
|
||||
reg = <0x0f0000 0x080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@170000 {
|
||||
label = "0:ART";
|
||||
reg = <0x170000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
flash@1 {
|
||||
status = "okay";
|
||||
|
||||
compatible = "spi-nand";
|
||||
reg = <1>;
|
||||
spi-max-frequency = <24000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "ubi";
|
||||
reg = <0x0000000 0x8000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&serial0_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
qcom,phy_mdio_addr = <2>;
|
||||
qcom,poll_required = <1>;
|
||||
};
|
||||
|
||||
&gmac1 {
|
||||
qcom,phy_mdio_addr = <4>;
|
||||
qcom,poll_required = <1>;
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
serial0_pins: serial0_pinmux {
|
||||
mux {
|
||||
function = "blsp_uart0";
|
||||
pins = "gpio60", "gpio61";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
spi0_pins: spi0_pinmux {
|
||||
mux {
|
||||
function = "blsp_spi0";
|
||||
pins = "gpio55", "gpio56", "gpio57";
|
||||
bias-disable;
|
||||
drive-strength = <12>;
|
||||
};
|
||||
|
||||
mux_cs {
|
||||
function = "gpio";
|
||||
pins = "gpio54", "gpio59";
|
||||
bias-disable;
|
||||
drive-strength = <2>;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb2_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_ss_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
|
||||
qcom,ath10k-calibration-variant = "Luma-WRTQ-329ACN";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
|
||||
qcom,ath10k-calibration-variant = "Luma-WRTQ-329ACN";
|
||||
};
|
||||
@ -222,8 +222,72 @@
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "SBL1";
|
||||
reg = <0x0 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "MIBIB";
|
||||
reg = <0x100000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@200000 {
|
||||
label = "BOOTCONFIG";
|
||||
reg = <0x200000 0x100000>;
|
||||
};
|
||||
|
||||
partition@300000 {
|
||||
label = "QSEE";
|
||||
reg = <0x300000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@400000 {
|
||||
label = "QSEE_1";
|
||||
reg = <0x400000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@500000 {
|
||||
label = "CDT";
|
||||
reg = <0x500000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@580000 {
|
||||
label = "CDT_1";
|
||||
reg = <0x580000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@600000 {
|
||||
label = "BOOTCONFIG1";
|
||||
reg = <0x600000 0x80000>;
|
||||
};
|
||||
|
||||
partition@680000 {
|
||||
label = "APPSBLENV";
|
||||
reg = <0x680000 0x80000>;
|
||||
};
|
||||
|
||||
partition@700000 {
|
||||
label = "APPSBL";
|
||||
reg = <0x700000 0x200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@900000 {
|
||||
label = "APPSBL_1";
|
||||
reg = <0x900000 0x200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1 {
|
||||
label = "Bootloader";
|
||||
reg = <0x0 0xb00000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
art: partition@b00000 {
|
||||
|
||||
@ -1,18 +1,6 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
/*
|
||||
* Device Tree Source for Linksys EA8300 (Dallas)
|
||||
*
|
||||
* Copyright (C) 2019 Jeff Kletsky
|
||||
*
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
#include "qcom-ipq4019-xx8300.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Linksys EA8300 (Dallas)";
|
||||
@ -73,304 +61,18 @@
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
button@0 {
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
button@1 {
|
||||
wps {
|
||||
label = "wps";
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
//
|
||||
// OEM U-Boot provides either
|
||||
// init=/sbin/init rootfstype=ubifs ubi.mtd=11,2048 \
|
||||
// root=ubi0:ubifs rootwait rw
|
||||
// or the same with ubi.mtd=13,2048
|
||||
//
|
||||
|
||||
chosen {
|
||||
bootargs-append = " root=/dev/ubiblock0_0 rootfstype=squashfs ro";
|
||||
};
|
||||
|
||||
memory {
|
||||
device_type = "memory";
|
||||
reg = <0x80000000 0x10000000>;
|
||||
};
|
||||
|
||||
soc {
|
||||
rng@22000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
mdio@90000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-psgmii@98000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
tcsr@194b000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x194b000 0x100>;
|
||||
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
usb2@60f8800 {
|
||||
status = "okay";
|
||||
|
||||
dwc3@6000000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
usb2_port1: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
usb3@8af8800 {
|
||||
status = "okay";
|
||||
|
||||
dwc3@8a00000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
usb3_port1: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
|
||||
usb3_port2: port@2 {
|
||||
reg = <2>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
crypto@8e3a000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog@b017000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-switch@c000000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&serial_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&nand {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&nand_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
nand@0 {
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "sbl1";
|
||||
reg = <0x0 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "mibib";
|
||||
reg = <0x100000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@200000 {
|
||||
label = "qsee";
|
||||
reg = <0x200000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@300000 {
|
||||
label = "cdt";
|
||||
reg = <0x300000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@380000 {
|
||||
label = "appsblenv";
|
||||
reg = <0x380000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@400000 {
|
||||
label = "ART";
|
||||
reg = <0x400000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@480000 {
|
||||
label = "appsbl";
|
||||
reg = <0x480000 0x200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@680000 {
|
||||
label = "u_env";
|
||||
reg = <0x680000 0x80000>;
|
||||
// writable -- U-Boot environment
|
||||
};
|
||||
|
||||
partition@700000 {
|
||||
label = "s_env";
|
||||
reg = <0x700000 0x40000>;
|
||||
// writable -- Boot counter records
|
||||
};
|
||||
|
||||
partition@740000 {
|
||||
label = "devinfo";
|
||||
reg = <0x740000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@780000 {
|
||||
label = "kernel";
|
||||
reg = <0x780000 0x5800000>;
|
||||
};
|
||||
|
||||
partition@a80000 {
|
||||
label = "rootfs";
|
||||
reg = <0xa80000 0x5500000>;
|
||||
};
|
||||
|
||||
partition@5f80000 {
|
||||
label = "alt_kernel";
|
||||
reg = <0x5f80000 0x5800000>;
|
||||
};
|
||||
|
||||
partition@6280000 {
|
||||
label = "alt_rootfs";
|
||||
reg = <0x6280000 0x5500000>;
|
||||
};
|
||||
|
||||
partition@b780000 {
|
||||
label = "sysdiag";
|
||||
reg = <0xb780000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@b880000 {
|
||||
label = "syscfg";
|
||||
reg = <0xb880000 0x4680000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
|
||||
perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
|
||||
wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
|
||||
|
||||
bridge@0,0 {
|
||||
reg = <0x00000000 0 0 0 0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
ranges;
|
||||
|
||||
wifi2: wifi@1,0 {
|
||||
compatible = "qcom,ath10k";
|
||||
reg = <0x00010000 0 0 0 0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
serial_0_pins: serial0-pinmux {
|
||||
pins = "gpio16", "gpio17";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
nand_pins: nand_pins {
|
||||
pullups {
|
||||
pins = "gpio53", "gpio58", "gpio59";
|
||||
function = "qpic";
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
// gpio61 controls led_usb
|
||||
|
||||
pulldowns {
|
||||
pins = "gpio55", "gpio56", "gpio57",
|
||||
"gpio60", "gpio62", "gpio63",
|
||||
"gpio64", "gpio65", "gpio66",
|
||||
"gpio67", "gpio68", "gpio69";
|
||||
function = "qpic";
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb2_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_ss_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
|
||||
@ -58,12 +58,13 @@
|
||||
ess-switch@c000000 {
|
||||
status = "okay";
|
||||
|
||||
switch_lan_bmp = <0x10>;
|
||||
switch_wan_bmp = <0x20>;
|
||||
switch_lan_bmp = <0x30>;
|
||||
switch_wan_bmp = <0x02>;
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
qcom,num_gmac = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
@ -1,5 +1,4 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
|
||||
@ -0,0 +1,80 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcom-ipq4019-xx8300.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Linksys MR8300 (Dallas)";
|
||||
compatible = "linksys,mr8300", "qcom,ipq4019";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_blue;
|
||||
led-failsafe = &led_red;
|
||||
led-running = &led_blue;
|
||||
led-upgrade = &led_amber;
|
||||
serial0 = &blsp1_uart1;
|
||||
};
|
||||
|
||||
// Top panel LEDs, above Linksys logo
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_red: red {
|
||||
label = "red:alarm";
|
||||
gpios = <&tlmm 47 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_amber: amber {
|
||||
label = "amber:programming";
|
||||
gpios = <&tlmm 22 GPIO_ACTIVE_HIGH>;
|
||||
panic-indicator;
|
||||
};
|
||||
|
||||
led_blue: blue {
|
||||
label = "blue:power";
|
||||
gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
// On back panel, above USB socket
|
||||
|
||||
led_usb: usb {
|
||||
label = "green:usb";
|
||||
gpios = <&tlmm 61 GPIO_ACTIVE_LOW>;
|
||||
trigger-sources = <&usb3_port1>, <&usb3_port2>,
|
||||
<&usb2_port1>;
|
||||
linux,default-trigger = "usbport";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
qcom,ath10k-calibration-variant = "linksys-mr8300-v0-fcc";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
ieee80211-freq-limit = <5170000 5330000>;
|
||||
qcom,ath10k-calibration-variant = "linksys-mr8300-v0-fcc";
|
||||
};
|
||||
|
||||
&wifi2 {
|
||||
status = "okay";
|
||||
ieee80211-freq-limit = <5490000 5835000>;
|
||||
qcom,ath10k-calibration-variant = "linksys-mr8300-v0-fcc";
|
||||
};
|
||||
@ -0,0 +1,346 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
model = "EdgeCore OAP-100";
|
||||
compatible = "edgecore,oap100";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_system;
|
||||
led-failsafe = &led_system;
|
||||
led-running = &led_system;
|
||||
led-upgrade = &led_system;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs-append = " root=/dev/ubiblock0_1";
|
||||
};
|
||||
|
||||
soc {
|
||||
mdio@90000 {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
ess-psgmii@98000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
tcsr@194b000 {
|
||||
/* select hostmode */
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x194b000 0x100>;
|
||||
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
usb2@60f8800 {
|
||||
status = "okay";
|
||||
|
||||
dwc3@6000000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
usb2_port1: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
usb3@8af8800 {
|
||||
status = "okay";
|
||||
|
||||
dwc3@8a00000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
usb3_port1: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
|
||||
usb3_port2: port@2 {
|
||||
reg = <2>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
crypto@8e3a000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog@b017000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-switch@c000000 {
|
||||
status = "okay";
|
||||
switch_mac_mode = <0x0>; /* mac mode for RGMII RMII */
|
||||
switch_initvlas = <0x0007c 0x54>; /* port0 status */
|
||||
switch_lan_bmp = <0x10>;
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
key {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
button@1 {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
|
||||
linux,input-type = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_system: led_system {
|
||||
label = "green:system";
|
||||
gpios = <&tlmm 22 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_2g {
|
||||
label = "blue:wlan2g";
|
||||
gpios = <&tlmm 34 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_5g {
|
||||
label = "blue:wlan5g";
|
||||
gpios = <&tlmm 35 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio_export {
|
||||
compatible = "gpio-export";
|
||||
#size-cells = <0>;
|
||||
|
||||
usb {
|
||||
gpio-export,name = "usb-power";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&tlmm 44 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
poe {
|
||||
gpio-export,name = "poe-power";
|
||||
gpio-export,output = <0>;
|
||||
gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
serial_0_pins: serial_pinmux {
|
||||
mux {
|
||||
pins = "gpio16", "gpio17";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
spi_0_pins: spi_0_pinmux {
|
||||
pinmux {
|
||||
function = "blsp_spi0";
|
||||
pins = "gpio13", "gpio14", "gpio15";
|
||||
drive-strength = <12>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
pinmux_cs {
|
||||
function = "gpio";
|
||||
pins = "gpio12";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
|
||||
nand_pins: nand_pins {
|
||||
pullups {
|
||||
pins = "gpio53", "gpio58", "gpio59";
|
||||
function = "qpic";
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
pulldowns {
|
||||
pins = "gpio54", "gpio55", "gpio56",
|
||||
"gpio57", "gpio60", "gpio61",
|
||||
"gpio62", "gpio63", "gpio64",
|
||||
"gpio65", "gpio66", "gpio67",
|
||||
"gpio68", "gpio69";
|
||||
function = "qpic";
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
|
||||
mdio_pins: mdio_pinmux {
|
||||
mux_1 {
|
||||
pins = "gpio6";
|
||||
function = "mdio";
|
||||
bias-pull-up;
|
||||
};
|
||||
mux_2 {
|
||||
pins = "gpio7";
|
||||
function = "mdc";
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
flash@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
linux,modalias = "m25p80", "gd25q256";
|
||||
spi-max-frequency = <24000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition0@0 {
|
||||
label = "0:SBL1";
|
||||
reg = <0x00000000 0x00040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition1@40000 {
|
||||
label = "0:MIBIB";
|
||||
reg = <0x00040000 0x00020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition2@60000 {
|
||||
label = "0:QSEE";
|
||||
reg = <0x00060000 0x00060000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition3@c0000 {
|
||||
label = "0:CDT";
|
||||
reg = <0x000c0000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition4@d0000 {
|
||||
label = "0:DDRPARAMS";
|
||||
reg = <0x000d0000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition5@e0000 {
|
||||
label = "0:APPSBLENV";
|
||||
reg = <0x000e0000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition6@f0000 {
|
||||
label = "0:APPSBL";
|
||||
reg = <0x000f0000 0x00080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition7@170000 {
|
||||
label = "0:ART";
|
||||
reg = <0x00170000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&nand {
|
||||
pinctrl-0 = <&nand_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "rootfs";
|
||||
reg = <0x00000000 0x4000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
pinctrl-0 = <&serial_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
qcom,ath10k-calibration-variant = "Edgecore OAP100";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
qcom,ath10k-calibration-variant = "Edgecore OAP100";
|
||||
};
|
||||
|
||||
&usb3_ss_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb2_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
@ -0,0 +1,203 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/* Copyright (c) 2017-2020, Sven Eckelmann <sven@narfation.org>
|
||||
* Copyright (c) 2018, Marek Lindner <marek.lindner@kaiwoo.ai>
|
||||
*/
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
model = "Plasma Cloud PA2200";
|
||||
compatible = "plasmacloud,pa2200";
|
||||
|
||||
soc {
|
||||
rng@22000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
mdio@90000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-psgmii@98000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
crypto@8e3a000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog@b017000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-switch@c000000 {
|
||||
switch_lan_bmp = <0x10>;
|
||||
switch_wan_bmp = <0x20>;
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART >;
|
||||
};
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power_orange;
|
||||
led-failsafe = &led_status_blue;
|
||||
led-running = &led_power_orange;
|
||||
led-upgrade = &led_status_blue;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power_orange: power_orange {
|
||||
label = "orange:power";
|
||||
gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
2g_blue {
|
||||
label = "blue:2g";
|
||||
gpios = <&tlmm 46 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
|
||||
2g_green {
|
||||
label = "green:5g1";
|
||||
gpios = <&tlmm 47 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
5g2_green {
|
||||
label = "green:5g2";
|
||||
gpios = <&tlmm 48 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy2tpt";
|
||||
};
|
||||
|
||||
led_status_blue: status_blue {
|
||||
label = "blue:status";
|
||||
gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
serial_pins: serial_pinmux {
|
||||
mux {
|
||||
pins = "gpio16", "gpio17";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
spi_0_pins: spi_0_pinmux {
|
||||
pin {
|
||||
function = "blsp_spi0";
|
||||
pins = "gpio13", "gpio14", "gpio15";
|
||||
drive-strength = <12>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
pin_cs {
|
||||
function = "gpio";
|
||||
pins = "gpio12";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
flash@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <24000000>;
|
||||
/* partitions are passed via bootloader */
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
pinctrl-0 = <&serial_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
|
||||
wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
|
||||
|
||||
bridge@0,0 {
|
||||
reg = <0x00000000 0 0 0 0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
ranges;
|
||||
|
||||
wifi2: wifi@1,0 {
|
||||
compatible = "qcom,ath10k";
|
||||
status = "okay";
|
||||
reg = <0x00010000 0 0 0 0>;
|
||||
qcom,ath10k-calibration-variant = "PlasmaCloud-PA2200";
|
||||
ieee80211-freq-limit = <5170000 5350000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
qcom,ath10k-calibration-variant = "PlasmaCloud-PA2200";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
qcom,ath10k-calibration-variant = "PlasmaCloud-PA2200";
|
||||
ieee80211-freq-limit = <5470000 5875000>;
|
||||
};
|
||||
@ -1,7 +1,5 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "qcom-ipq4019-u4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
@ -0,0 +1,300 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
/*
|
||||
* Device Tree Source for Linksys xx8300 (Dallas)
|
||||
*
|
||||
* Copyright (C) 2019 Jeff Kletsky
|
||||
* Updated 2020 Hans Geiblinger
|
||||
*
|
||||
*/
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
//
|
||||
// OEM U-Boot provides either
|
||||
// init=/sbin/init rootfstype=ubifs ubi.mtd=11,2048 \
|
||||
// root=ubi0:ubifs rootwait rw
|
||||
// or the same with ubi.mtd=13,2048
|
||||
//
|
||||
|
||||
/ {
|
||||
chosen {
|
||||
bootargs-append = " root=/dev/ubiblock0_0 rootfstype=squashfs ro";
|
||||
};
|
||||
|
||||
|
||||
soc {
|
||||
rng@22000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
mdio@90000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-psgmii@98000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
tcsr@194b000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x194b000 0x100>;
|
||||
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
usb2@60f8800 {
|
||||
status = "okay";
|
||||
|
||||
dwc3@6000000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
usb2_port1: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
usb3@8af8800 {
|
||||
status = "okay";
|
||||
|
||||
dwc3@8a00000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
usb3_port1: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
|
||||
usb3_port2: port@2 {
|
||||
reg = <2>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
crypto@8e3a000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog@b017000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-switch@c000000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&serial_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&nand {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&nand_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
nand@0 {
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "sbl1";
|
||||
reg = <0x0 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "mibib";
|
||||
reg = <0x100000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@200000 {
|
||||
label = "qsee";
|
||||
reg = <0x200000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@300000 {
|
||||
label = "cdt";
|
||||
reg = <0x300000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@380000 {
|
||||
label = "appsblenv";
|
||||
reg = <0x380000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@400000 {
|
||||
label = "ART";
|
||||
reg = <0x400000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@480000 {
|
||||
label = "appsbl";
|
||||
reg = <0x480000 0x200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@680000 {
|
||||
label = "u_env";
|
||||
reg = <0x680000 0x80000>;
|
||||
// writable -- U-Boot environment
|
||||
};
|
||||
|
||||
partition@700000 {
|
||||
label = "s_env";
|
||||
reg = <0x700000 0x40000>;
|
||||
// writable -- Boot counter records
|
||||
};
|
||||
|
||||
partition@740000 {
|
||||
label = "devinfo";
|
||||
reg = <0x740000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@780000 {
|
||||
label = "kernel";
|
||||
reg = <0x780000 0x5800000>;
|
||||
};
|
||||
|
||||
partition@a80000 {
|
||||
label = "rootfs";
|
||||
reg = <0xa80000 0x5500000>;
|
||||
};
|
||||
|
||||
partition@5f80000 {
|
||||
label = "alt_kernel";
|
||||
reg = <0x5f80000 0x5800000>;
|
||||
};
|
||||
|
||||
partition@6280000 {
|
||||
label = "alt_rootfs";
|
||||
reg = <0x6280000 0x5500000>;
|
||||
};
|
||||
|
||||
partition@b780000 {
|
||||
label = "sysdiag";
|
||||
reg = <0xb780000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@b880000 {
|
||||
label = "syscfg";
|
||||
reg = <0xb880000 0x4680000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
|
||||
perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
|
||||
wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
|
||||
|
||||
bridge@0,0 {
|
||||
reg = <0x00000000 0 0 0 0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
ranges;
|
||||
|
||||
wifi2: wifi@1,0 {
|
||||
compatible = "qcom,ath10k";
|
||||
reg = <0x00010000 0 0 0 0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
serial_0_pins: serial0-pinmux {
|
||||
pins = "gpio16", "gpio17";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
nand_pins: nand_pins {
|
||||
pullups {
|
||||
pins = "gpio53", "gpio58", "gpio59";
|
||||
function = "qpic";
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
// gpio61 controls led_usb
|
||||
|
||||
pulldowns {
|
||||
pins = "gpio55", "gpio56", "gpio57",
|
||||
"gpio60", "gpio62", "gpio63",
|
||||
"gpio64", "gpio65", "gpio66",
|
||||
"gpio67", "gpio68", "gpio69";
|
||||
function = "qpic";
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb2_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_ss_phy {
|
||||
status = "okay";
|
||||
};
|
||||
@ -145,10 +145,8 @@
|
||||
};
|
||||
|
||||
partition@380000 {
|
||||
/* This is empty */
|
||||
label = "appsblenv";
|
||||
reg = <0x380000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@390000 {
|
||||
|
||||
@ -138,7 +138,6 @@
|
||||
partition@e0000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0xe0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@f0000 {
|
||||
|
||||
@ -1,805 +1,19 @@
|
||||
include $(TOPDIR)/rules.mk
|
||||
include $(INCLUDE_DIR)/image.mk
|
||||
|
||||
DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
|
||||
DEVICE_VARS += RAS_BOARD RAS_ROOTFS_SIZE RAS_VERSION
|
||||
DEVICE_VARS += WRGG_DEVNAME WRGG_SIGNATURE
|
||||
|
||||
define Device/Default
|
||||
PROFILES := Default
|
||||
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
|
||||
KERNEL_INITRAMFS_PREFIX := $$(IMG_PREFIX)-$(1)-initramfs
|
||||
KERNEL_PREFIX := $$(DEVICE_IMG_PREFIX)
|
||||
KERNEL_LOADADDR := 0x80208000
|
||||
DEVICE_DTS = $$(SOC)-$(lastword $(subst _, ,$(1)))
|
||||
DEVICE_DTS_CONFIG := config@1
|
||||
IMAGES := sysupgrade.bin
|
||||
IMAGE/sysupgrade.bin = sysupgrade-tar | append-metadata
|
||||
IMAGE/sysupgrade.bin/squashfs :=
|
||||
endef
|
||||
|
||||
define Device/FitImage
|
||||
KERNEL_SUFFIX := -fit-uImage.itb
|
||||
KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
|
||||
KERNEL_NAME := Image
|
||||
endef
|
||||
|
||||
define Device/FitImageLzma
|
||||
KERNEL_SUFFIX := -fit-uImage.itb
|
||||
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb
|
||||
KERNEL_NAME := Image
|
||||
endef
|
||||
|
||||
define Device/FitzImage
|
||||
KERNEL_SUFFIX := -fit-zImage.itb
|
||||
KERNEL = kernel-bin | fit none $$(DTS_DIR)/$$(DEVICE_DTS).dtb
|
||||
KERNEL_NAME := zImage
|
||||
endef
|
||||
|
||||
define Device/UbiFit
|
||||
KERNEL_IN_UBI := 1
|
||||
IMAGES := nand-factory.ubi nand-sysupgrade.bin
|
||||
IMAGE/nand-factory.ubi := append-ubi
|
||||
IMAGE/nand-sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
endef
|
||||
|
||||
define Device/DniImage
|
||||
$(call Device/FitzImage)
|
||||
NETGEAR_BOARD_ID :=
|
||||
NETGEAR_HW_ID :=
|
||||
IMAGES += factory.img
|
||||
IMAGE/factory.img := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | netgear-dni
|
||||
IMAGE/sysupgrade.bin := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | \
|
||||
append-rootfs | pad-rootfs | check-size | append-metadata
|
||||
endef
|
||||
|
||||
define Build/append-rootfshdr
|
||||
mkimage -A $(LINUX_KARCH) \
|
||||
-O linux -T filesystem \
|
||||
-C lzma -a $(KERNEL_LOADADDR) -e $(if $(KERNEL_ENTRY),$(KERNEL_ENTRY),$(KERNEL_LOADADDR)) \
|
||||
-n root.squashfs -d $(IMAGE_ROOTFS) $@.new
|
||||
dd if=$@.new bs=64 count=1 >> $(IMAGE_KERNEL)
|
||||
endef
|
||||
|
||||
define Build/mkmylofw_32m
|
||||
$(eval device_id=$(word 1,$(1)))
|
||||
$(eval revision=$(word 2,$(1)))
|
||||
|
||||
let \
|
||||
size="$$(stat -c%s $@)" \
|
||||
pad="$(subst k,* 1024,$(BLOCKSIZE))" \
|
||||
pad="(pad - (size % pad)) % pad" \
|
||||
newsize='size + pad'; \
|
||||
$(STAGING_DIR_HOST)/bin/mkmylofw \
|
||||
-B WPE72 -i 0x11f6:$(device_id):0x11f6:$(device_id) -r $(revision) \
|
||||
-s 0x2000000 -p0x180000:$$newsize:al:0x80208000:"OpenWrt":$@ \
|
||||
$@.new
|
||||
@mv $@.new $@
|
||||
endef
|
||||
|
||||
define Build/qsdk-ipq-factory-nand-askey
|
||||
$(TOPDIR)/scripts/mkits-qsdk-ipq-image.sh $@.its\
|
||||
askey_kernel $(IMAGE_KERNEL) \
|
||||
askey_fs $(IMAGE_ROOTFS) \
|
||||
ubifs $@
|
||||
PATH=$(LINUX_DIR)/scripts/dtc:$(PATH) mkimage -f $@.its $@.new
|
||||
@mv $@.new $@
|
||||
endef
|
||||
|
||||
define Build/SenaoFW
|
||||
-$(STAGING_DIR_HOST)/bin/mksenaofw \
|
||||
-n $(BOARD_NAME) -r $(VENDOR_ID) -p $(1) \
|
||||
-c $(DATECODE) -w $(2) -x $(CW_VER) -t 0 \
|
||||
-e $@ \
|
||||
-o $@.new
|
||||
@cp $@.new $@
|
||||
endef
|
||||
|
||||
define Build/wrgg-image
|
||||
mkwrggimg -i $@ \
|
||||
-o $@.new \
|
||||
-d "$(WRGG_DEVNAME)" \
|
||||
-s "$(WRGG_SIGNATURE)" \
|
||||
-v "" -m "" -B ""
|
||||
mv $@.new $@
|
||||
endef
|
||||
|
||||
define Device/8dev_habanero-dvk
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := 8devices
|
||||
DEVICE_MODEL := Habanero DVK
|
||||
IMAGE_SIZE := 30976k
|
||||
DEVICE_DTS := qcom-ipq4019-habanero-dvk
|
||||
DEVICE_PACKAGES := ipq-wifi-8dev_habanero-dvk
|
||||
IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | append-rootfs | pad-rootfs | check-size | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += 8dev_habanero-dvk
|
||||
|
||||
define Device/8dev_jalapeno-common
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
endef
|
||||
|
||||
define Device/8dev_jalapeno
|
||||
$(call Device/8dev_jalapeno-common)
|
||||
DEVICE_VENDOR := 8devices
|
||||
DEVICE_MODEL := Jalapeno
|
||||
DEVICE_DTS := qcom-ipq4018-jalapeno
|
||||
endef
|
||||
TARGET_DEVICES += 8dev_jalapeno
|
||||
|
||||
define Device/alfa-network_ap120c-ac
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := ALFA Network
|
||||
DEVICE_MODEL := AP120C-AC
|
||||
DEVICE_DTS := qcom-ipq4018-ap120c-ac
|
||||
DEVICE_PACKAGES := kmod-usb-acm kmod-tpm-i2c-atmel
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
IMAGE_SIZE := 65536k
|
||||
IMAGES := nand-factory.bin nand-sysupgrade.bin
|
||||
IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
|
||||
endef
|
||||
TARGET_DEVICES += alfa-network_ap120c-ac
|
||||
|
||||
define Device/aruba_glenmorangie
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := Aruba
|
||||
DEVICE_PACKAGES := ipq-wifi-aruba_ap-303
|
||||
endef
|
||||
|
||||
define Device/aruba_ap-303
|
||||
$(call Device/aruba_glenmorangie)
|
||||
DEVICE_MODEL := AP-303
|
||||
DEVICE_DTS := qcom-ipq4029-ap-303
|
||||
endef
|
||||
TARGET_DEVICES += aruba_ap-303
|
||||
|
||||
define Device/aruba_ap-303h
|
||||
$(call Device/aruba_glenmorangie)
|
||||
DEVICE_MODEL := AP-303H
|
||||
DEVICE_DTS := qcom-ipq4029-ap-303h
|
||||
endef
|
||||
TARGET_DEVICES += aruba_ap-303h
|
||||
|
||||
define Device/aruba_ap-365
|
||||
$(call Device/aruba_glenmorangie)
|
||||
DEVICE_MODEL := AP-365
|
||||
DEVICE_DTS := qcom-ipq4029-ap-365
|
||||
DEVICE_PACKAGES += kmod-hwmon-ad7418
|
||||
endef
|
||||
TARGET_DEVICES += aruba_ap-365
|
||||
|
||||
define Device/asus_map-ac2200
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := ASUS
|
||||
DEVICE_MODEL := Lyra (MAP-AC2200)
|
||||
DEVICE_DTS := qcom-ipq4019-map-ac2200
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca9888 kmod-ath3k
|
||||
endef
|
||||
TARGET_DEVICES += asus_map-ac2200
|
||||
|
||||
define Device/asus_rt-ac58u
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := ASUS
|
||||
DEVICE_MODEL := RT-AC58U
|
||||
DEVICE_DTS := qcom-ipq4018-rt-ac58u
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DTB_SIZE := 65536
|
||||
IMAGE_SIZE := 20439364
|
||||
FILESYSTEMS := squashfs
|
||||
# Someone - in their infinite wisdom - decided to put the firmware
|
||||
# version in front of the image name \03\00\00\04 => Version 3.0.0.4
|
||||
# Since u-boot works with strings we either need another fixup step
|
||||
# to add a version... or we are very careful not to add '\0' into that
|
||||
# string and call it a day.... Yeah, we do the latter!
|
||||
UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC58U')
|
||||
KERNEL_INITRAMFS := $$(KERNEL) | uImage none
|
||||
KERNEL_INITRAMFS_SUFFIX := -factory.trx
|
||||
DEVICE_PACKAGES := -kmod-ath10k -ath10k-firmware-qca4019 \
|
||||
kmod-ath10k-ct-smallbuffers ath10k-firmware-qca4019-ct kmod-usb-ledtrig-usbport
|
||||
endef
|
||||
TARGET_DEVICES += asus_rt-ac58u
|
||||
|
||||
define Device/asus_rt-acrh17
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := ASUS
|
||||
DEVICE_MODEL := RT-ACRH17
|
||||
DEVICE_DTS := qcom-ipq4019-rt-acrh17
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DTB_SIZE := 65536
|
||||
IMAGE_SIZE := 20439364
|
||||
FILESYSTEMS := squashfs
|
||||
UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC82U')
|
||||
KERNEL_INITRAMFS := $$(KERNEL) | uImage none
|
||||
KERNEL_INITRAMFS_SUFFIX := -factory.trx
|
||||
DEVICE_PACKAGES := ipq-wifi-asus_rt-acrh17 ath10k-firmware-qca9984 kmod-usb-ledtrig-usbport
|
||||
endef
|
||||
TARGET_DEVICES += asus_rt-acrh17
|
||||
|
||||
define Device/avm_fritzbox-4040
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := AVM
|
||||
DEVICE_MODEL := FRITZ!Box 4040
|
||||
DEVICE_DTS := qcom-ipq4018-fritzbox-4040
|
||||
BOARD_NAME := fritz4040
|
||||
IMAGE_SIZE := 29056k
|
||||
UBOOT_PATH := $(STAGING_DIR_IMAGE)/uboot-fritz4040.bin
|
||||
UBOOT_PARTITION_SIZE := 524288
|
||||
IMAGES += eva.bin
|
||||
IMAGE/eva.bin := append-uboot | pad-to $$$$(UBOOT_PARTITION_SIZE) | append-kernel | append-rootfs | pad-rootfs
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata
|
||||
DEVICE_PACKAGES := fritz-tffs fritz-caldata
|
||||
endef
|
||||
TARGET_DEVICES += avm_fritzbox-4040
|
||||
|
||||
define Device/avm_fritzbox-7530
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := AVM
|
||||
DEVICE_MODEL := FRITZ!Box 7530
|
||||
DEVICE_DTS := qcom-ipq4019-fritzbox-7530
|
||||
DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand
|
||||
endef
|
||||
TARGET_DEVICES += avm_fritzbox-7530
|
||||
|
||||
define Device/avm_fritzrepeater-1200
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := AVM
|
||||
DEVICE_MODEL := FRITZ!Repeater 1200
|
||||
DEVICE_DTS := qcom-ipq4019-fritzrepeater-1200
|
||||
DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand ipq-wifi-avm_fritzrepeater-1200
|
||||
endef
|
||||
TARGET_DEVICES += avm_fritzrepeater-1200
|
||||
|
||||
define Device/avm_fritzrepeater-3000
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := AVM
|
||||
DEVICE_MODEL := FRITZ!Repeater 3000
|
||||
DEVICE_DTS := qcom-ipq4019-fritzrepeater-3000
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca9984 fritz-caldata fritz-tffs-nand
|
||||
endef
|
||||
TARGET_DEVICES += avm_fritzrepeater-3000
|
||||
|
||||
define Device/buffalo_wtr-m2133hp
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := Buffalo
|
||||
DEVICE_MODEL := WTR-M2133HP
|
||||
DEVICE_DTS := qcom-ipq4019-wtr-m2133hp
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca9984 ipq-wifi-buffalo_wtr-m2133hp
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
endef
|
||||
TARGET_DEVICES += buffalo_wtr-m2133hp
|
||||
|
||||
define Device/cellc_rtl30vw
|
||||
KERNEL_SUFFIX := -fit-uImage.itb
|
||||
KERNEL_INITRAMFS = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
|
||||
KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb | uImage lzma | pad-to 2048
|
||||
KERNEL_NAME := Image
|
||||
KERNEL_IN_UBI :=
|
||||
IMAGES := nand-factory.bin nand-sysupgrade.bin
|
||||
IMAGE/nand-factory.bin := append-rootfshdr | append-ubi | qsdk-ipq-factory-nand-askey
|
||||
IMAGE/nand-sysupgrade.bin := append-rootfshdr | sysupgrade-tar | append-metadata
|
||||
DEVICE_VENDOR := Cell C
|
||||
DEVICE_MODEL := RTL30VW
|
||||
DEVICE_DTS := qcom-ipq4019-rtl30vw
|
||||
DEVICE_DTS_CONFIG := config@5
|
||||
KERNEL_INSTALL := 1
|
||||
KERNEL_SIZE := 4096k
|
||||
IMAGE_SIZE := 57344k
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_PACKAGES := kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi ipq-wifi-cellc_rtl30vw
|
||||
endef
|
||||
TARGET_DEVICES += cellc_rtl30vw
|
||||
|
||||
define Device/century_wr142ac
|
||||
$(call Device/FitzImage)
|
||||
DEVICE_VENDOR := Century
|
||||
DEVICE_MODEL := WR142AC
|
||||
DEVICE_DTS := qcom-ipq4019-wr142ac
|
||||
KERNEL_SIZE := 4096k
|
||||
IMAGE_SIZE := 31232k
|
||||
IMAGES += factory.bin
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size
|
||||
DEVICE_PACKAGES := ipq-wifi-century_wr142ac kmod-usb-ledtrig-usbport
|
||||
endef
|
||||
TARGET_DEVICES += century_wr142ac
|
||||
|
||||
define Device/century_wr142ac-nand
|
||||
$(call Device/FitzImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := Century
|
||||
DEVICE_MODEL := WR142AC
|
||||
DEVICE_VARIANT := NAND
|
||||
DEVICE_DTS := qcom-ipq4019-wr142ac-nand
|
||||
DEVICE_DTS_CONFIG := config@10
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_PACKAGES := ipq-wifi-century_wr142ac kmod-usb-ledtrig-usbport
|
||||
endef
|
||||
TARGET_DEVICES += century_wr142ac-nand
|
||||
|
||||
define Device/cilab_meshpoint-one
|
||||
$(call Device/8dev_jalapeno-common)
|
||||
DEVICE_VENDOR := Crisis Innovation Lab
|
||||
DEVICE_MODEL := MeshPoint.One
|
||||
DEVICE_DTS := qcom-ipq4018-meshpoint-one
|
||||
DEVICE_PACKAGES := kmod-i2c-gpio kmod-iio-bmp280-i2c kmod-hwmon-ina2xx kmod-rtc-pcf2127
|
||||
endef
|
||||
TARGET_DEVICES += cilab_meshpoint-one
|
||||
|
||||
define Device/compex_wpj419
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := Compex
|
||||
DEVICE_MODEL := WPJ419
|
||||
DEVICE_DTS := qcom-ipq4019-wpj419
|
||||
DEVICE_DTS_CONFIG := config@12
|
||||
KERNEL_INSTALL := 1
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
FILESYSTEMS := squashfs
|
||||
endef
|
||||
TARGET_DEVICES += compex_wpj419
|
||||
|
||||
define Device/compex_wpj428
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := Compex
|
||||
DEVICE_MODEL := WPJ428
|
||||
DEVICE_DTS := qcom-ipq4028-wpj428
|
||||
DEVICE_DTS_CONFIG := config@4
|
||||
BLOCKSIZE := 64k
|
||||
IMAGE_SIZE := 31232k
|
||||
KERNEL_SIZE := 4096k
|
||||
IMAGES += cpximg-6a04.bin
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
IMAGE/cpximg-6a04.bin := append-kernel | append-rootfs | pad-rootfs | mkmylofw_32m 0x8A2 3
|
||||
DEVICE_PACKAGES := kmod-gpio-beeper
|
||||
endef
|
||||
TARGET_DEVICES += compex_wpj428
|
||||
|
||||
define Device/dlink_dap-2610
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := D-Link
|
||||
DEVICE_MODEL := DAP-2610
|
||||
DEVICE_DTS := qcom-ipq4018-dap-2610
|
||||
DEVICE_DTS_CONFIG := config@ap.dk01.1-c1
|
||||
BLOCKSIZE := 64k
|
||||
WRGG_DEVNAME := /dev/mtdblock/8
|
||||
WRGG_SIGNATURE := wapac30_dkbs_dap2610
|
||||
IMAGE_SIZE := 14080k
|
||||
IMAGES += factory.bin
|
||||
# Bootloader expects a special 160 byte header which is added by
|
||||
# wrgg-image.
|
||||
# Factory image size must be larger than 6MB, and size in wrgg header must
|
||||
# match actual factory image size to be flashable from D-Link http server.
|
||||
# Bootloader verifies checksum of wrgg image before booting, thus jffs2
|
||||
# cannot be part of the wrgg image. This is solved in the factory image by
|
||||
# having the rootfs at the end of the image (without pad-rootfs). And in
|
||||
# the sysupgrade image only the kernel is included in the wrgg checksum,
|
||||
# but this is not flashable from the D-link http server.
|
||||
# append-rootfs must start on an erase block boundary.
|
||||
IMAGE/factory.bin := append-kernel | pad-offset 6144k 160 | append-rootfs | wrgg-image | check-size
|
||||
IMAGE/sysupgrade.bin := append-kernel | wrgg-image | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size | append-metadata
|
||||
DEVICE_PACKAGES := ipq-wifi-dlink_dap2610
|
||||
endef
|
||||
TARGET_DEVICES += dlink_dap-2610
|
||||
|
||||
define Device/engenius_eap1300
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := EnGenius
|
||||
DEVICE_MODEL := EAP1300
|
||||
DEVICE_DTS := qcom-ipq4018-eap1300
|
||||
DEVICE_DTS_CONFIG := config@4
|
||||
BOARD_NAME := eap1300
|
||||
KERNEL_SIZE := 5120k
|
||||
IMAGE_SIZE := 25344k
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += engenius_eap1300
|
||||
|
||||
define Device/engenius_eap2200
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := EnGenius
|
||||
DEVICE_MODEL := EAP2200
|
||||
DEVICE_DTS := qcom-ipq4019-eap2200
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca9888 ipq-wifi-engenius_eap2200 -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers
|
||||
endef
|
||||
TARGET_DEVICES += engenius_eap2200
|
||||
|
||||
define Device/engenius_emd1
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := EnGenius
|
||||
DEVICE_MODEL := EMD1
|
||||
DEVICE_DTS := qcom-ipq4018-emd1
|
||||
DEVICE_DTS_CONFIG := config@4
|
||||
IMAGE_SIZE := 30720k
|
||||
IMAGES += factory.bin
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size
|
||||
endef
|
||||
TARGET_DEVICES += engenius_emd1
|
||||
|
||||
define Device/engenius_emr3500
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := EnGenius
|
||||
DEVICE_MODEL := EMR3500
|
||||
DEVICE_DTS := qcom-ipq4018-emr3500
|
||||
DEVICE_DTS_CONFIG := config@4
|
||||
KERNEL_SIZE := 4096k
|
||||
IMAGE_SIZE := 30720k
|
||||
IMAGES += factory.bin
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size
|
||||
endef
|
||||
TARGET_DEVICES += engenius_emr3500
|
||||
|
||||
define Device/engenius_ens620ext
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := EnGenius
|
||||
DEVICE_MODEL := ENS620EXT
|
||||
DEVICE_DTS := qcom-ipq4018-ens620ext
|
||||
DEVICE_DTS_CONFIG := config@4
|
||||
BLOCKSIZE := 64k
|
||||
PAGESIZE := 256
|
||||
BOARD_NAME := ENS620EXT
|
||||
VENDOR_ID := 0x0101
|
||||
PRODUCT_ID := 0x79
|
||||
PRODUCT_ID_NEW := 0xA4
|
||||
DATECODE := 190507
|
||||
FW_VER := 3.1.2
|
||||
FW_VER_NEW := 3.5.6
|
||||
CW_VER := 1.8.99
|
||||
IMAGE_SIZE := 21312k
|
||||
KERNEL_SIZE := 5120k
|
||||
FILESYSTEMS := squashfs
|
||||
IMAGES += factory_30.bin factory_35.bin
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata
|
||||
IMAGE/factory_30.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | check-size | SenaoFW $$$$(PRODUCT_ID) $$$$(FW_VER)
|
||||
IMAGE/factory_35.bin := qsdk-ipq-factory-nor | check-size | SenaoFW $$$$(PRODUCT_ID_NEW) $$$$(FW_VER_NEW)
|
||||
endef
|
||||
TARGET_DEVICES += engenius_ens620ext
|
||||
|
||||
define Device/ezviz_cs-w3-wd1200g-eup
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := EZVIZ
|
||||
DEVICE_MODEL := CS-W3-WD1200G
|
||||
DEVICE_VARIANT := EUP
|
||||
DEVICE_DTS_CONFIG := config@4
|
||||
IMAGE_SIZE := 14848k
|
||||
DEVICE_DTS := qcom-ipq4018-cs-w3-wd1200g-eup
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
|
||||
append-metadata
|
||||
DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers \
|
||||
ipq-wifi-ezviz_cs-w3-wd1200g-eup
|
||||
endef
|
||||
TARGET_DEVICES += ezviz_cs-w3-wd1200g-eup
|
||||
|
||||
define Device/glinet_gl-b1300
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := GL.iNet
|
||||
DEVICE_MODEL := GL-B1300
|
||||
BOARD_NAME := gl-b1300
|
||||
DEVICE_DTS := qcom-ipq4029-gl-b1300
|
||||
KERNEL_SIZE := 4096k
|
||||
IMAGE_SIZE := 26624k
|
||||
IMAGE/sysupgrade.bin := append-kernel |append-rootfs | pad-rootfs | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += glinet_gl-b1300
|
||||
|
||||
define Device/glinet_gl-s1300
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := GL.iNet
|
||||
DEVICE_MODEL := GL-S1300
|
||||
DEVICE_DTS := qcom-ipq4029-gl-s1300
|
||||
KERNEL_SIZE := 4096k
|
||||
IMAGE_SIZE := 26624k
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
DEVICE_PACKAGES := ipq-wifi-glinet_gl-s1300 kmod-fs-ext4 kmod-mmc kmod-spi-dev
|
||||
endef
|
||||
TARGET_DEVICES += glinet_gl-s1300
|
||||
|
||||
define Device/hiwifi_c526a
|
||||
$(call Device/FitzImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := HiWiFi
|
||||
DEVICE_MODEL := C526A
|
||||
DEVICE_DTS := qcom-ipq4019-c526a
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_PACKAGES := ipq-wifi-hiwifi_c526a kmod-mt7615e kmod-mt7615-firmware
|
||||
endef
|
||||
TARGET_DEVICES += hiwifi_c526a
|
||||
|
||||
define Device/hiwifi_c526a-128m
|
||||
$(call Device/hiwifi_c526a)
|
||||
DEVICE_VARIANT := 128M
|
||||
DEVICE_DTS := qcom-ipq4019-c526a-128m
|
||||
endef
|
||||
TARGET_DEVICES += hiwifi_c526a-128m
|
||||
|
||||
define Device/leguang_ca100
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := LEGUANG
|
||||
DEVICE_MODEL := CA100
|
||||
DEVICE_DTS := qcom-ipq4019-ca100
|
||||
KERNEL_SIZE := 4096k
|
||||
IMAGE_SIZE := 31232k
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
DEVICE_PACKAGES := ipq-wifi-leguang_ca100
|
||||
endef
|
||||
TARGET_DEVICES += leguang_ca100
|
||||
|
||||
define Device/linksys_ea6350v3
|
||||
# The Linksys EA6350v3 has a uboot bootloader that does not
|
||||
# support either booting lzma kernel images nor booting UBI
|
||||
# partitions. This uboot, however, supports raw kernel images and
|
||||
# gzipped images.
|
||||
#
|
||||
# As for the time of writing this, the device will boot the kernel
|
||||
# from a fixed address with a fixed length of 3MiB. Also, the
|
||||
# device has a hard-coded kernel command line that requieres the
|
||||
# rootfs and alt_rootfs to be in mtd11 and mtd13 respectively.
|
||||
# Oh... and the kernel partition overlaps with the rootfs
|
||||
# partition (the same for alt_kernel and alt_rootfs).
|
||||
#
|
||||
# If you are planing re-partitioning the device, you may want to
|
||||
# keep those details in mind:
|
||||
# 1. The kernel adresses you should honor are 0x00000000 and
|
||||
# 0x02800000 respectively.
|
||||
# 2. The kernel size (plus the dtb) cannot exceed 3.00MiB in size.
|
||||
# 3. You can use 'zImage', but not a raw 'Image' packed with lzma.
|
||||
# 4. The kernel command line from uboot is harcoded to boot with
|
||||
# rootfs either in mtd11 or mtd13.
|
||||
$(call Device/FitzImage)
|
||||
DEVICE_VENDOR := Linksys
|
||||
DEVICE_MODEL := EA6350
|
||||
DEVICE_VARIANT := v3
|
||||
DEVICE_DTS := qcom-ipq4018-ea6350v3
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
KERNEL_SIZE := 3072k
|
||||
IMAGE_SIZE := 37888k
|
||||
UBINIZE_OPTS := -E 5
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-kernel | append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=EA6350v3
|
||||
endef
|
||||
TARGET_DEVICES += linksys_ea6350v3
|
||||
|
||||
define Device/linksys_ea8300
|
||||
$(call Device/FitzImage)
|
||||
DEVICE_VENDOR := Linksys
|
||||
DEVICE_MODEL := EA8300
|
||||
DEVICE_DTS := qcom-ipq4019-ea8300
|
||||
KERNEL_SIZE := 3072k
|
||||
IMAGE_SIZE := 87040k
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=EA8300
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca9888 ipq-wifi-linksys_ea8300 kmod-usb-ledtrig-usbport
|
||||
endef
|
||||
TARGET_DEVICES += linksys_ea8300
|
||||
|
||||
define Device/meraki_mr33
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := Cisco Meraki
|
||||
DEVICE_MODEL := MR33
|
||||
DEVICE_DTS := qcom-ipq4029-mr33
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_PACKAGES := -swconfig ath10k-firmware-qca9887
|
||||
endef
|
||||
TARGET_DEVICES += meraki_mr33
|
||||
|
||||
define Device/mobipromo_cm520-79f
|
||||
$(call Device/FitzImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := MobiPromo
|
||||
DEVICE_MODEL := CM520-79F
|
||||
DEVICE_DTS := qcom-ipq4019-cm520-79f
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_PACKAGES := ipq-wifi-mobipromo_cm520-79f kmod-usb-ledtrig-usbport
|
||||
endef
|
||||
TARGET_DEVICES += mobipromo_cm520-79f
|
||||
|
||||
define Device/netgear_ex61x0v2
|
||||
$(call Device/DniImage)
|
||||
DEVICE_DTS_CONFIG := config@4
|
||||
NETGEAR_BOARD_ID := EX6150v2series
|
||||
NETGEAR_HW_ID := 29765285+16+0+128+2x2
|
||||
IMAGE_SIZE := 14400k
|
||||
endef
|
||||
|
||||
define Device/netgear_ex6100v2
|
||||
$(call Device/netgear_ex61x0v2)
|
||||
DEVICE_VENDOR := Netgear
|
||||
DEVICE_MODEL := EX6100
|
||||
DEVICE_VARIANT := v2
|
||||
DEVICE_DTS := qcom-ipq4018-ex6100v2
|
||||
endef
|
||||
TARGET_DEVICES += netgear_ex6100v2
|
||||
|
||||
define Device/netgear_ex6150v2
|
||||
$(call Device/netgear_ex61x0v2)
|
||||
DEVICE_VENDOR := Netgear
|
||||
DEVICE_MODEL := EX6150
|
||||
DEVICE_VARIANT := v2
|
||||
DEVICE_DTS := qcom-ipq4018-ex6150v2
|
||||
endef
|
||||
TARGET_DEVICES += netgear_ex6150v2
|
||||
|
||||
define Device/netgear_ex6200v2
|
||||
$(call Device/DniImage)
|
||||
DEVICE_DTS_CONFIG := config@4
|
||||
NETGEAR_HW_ID := 29765265+16+0+256+2x2+2x2
|
||||
DEVICE_VENDOR := Netgear
|
||||
DEVICE_MODEL := EX6200
|
||||
DEVICE_VARIANT := v2
|
||||
DEVICE_DTS := qcom-ipq4018-ex6200v2
|
||||
DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport
|
||||
endef
|
||||
TARGET_DEVICES += netgear_ex6200v2
|
||||
|
||||
define Device/openmesh_a42
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := OpenMesh
|
||||
DEVICE_MODEL := A42
|
||||
DEVICE_DTS := qcom-ipq4018-a42
|
||||
DEVICE_DTS_CONFIG := config@om.a42
|
||||
BLOCKSIZE := 64k
|
||||
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
|
||||
IMAGE_SIZE := 15616k
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A42
|
||||
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += openmesh_a42
|
||||
|
||||
define Device/openmesh_a62
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := OpenMesh
|
||||
DEVICE_MODEL := A62
|
||||
DEVICE_DTS := qcom-ipq4019-a62
|
||||
DEVICE_DTS_CONFIG := config@om.a62
|
||||
BLOCKSIZE := 64k
|
||||
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
|
||||
IMAGE_SIZE := 15552k
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A62
|
||||
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca9888
|
||||
endef
|
||||
TARGET_DEVICES += openmesh_a62
|
||||
|
||||
define Device/p2w_r619ac
|
||||
$(call Device/FitzImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := P&W
|
||||
DEVICE_MODEL := R619AC
|
||||
DEVICE_DTS := qcom-ipq4019-r619ac
|
||||
DEVICE_DTS_CONFIG := config@10
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_PACKAGES := ipq-wifi-p2w_r619ac
|
||||
endef
|
||||
TARGET_DEVICES += p2w_r619ac
|
||||
|
||||
define Device/qcom_ap-dk01.1-c1
|
||||
DEVICE_VENDOR := Qualcomm Atheros
|
||||
DEVICE_MODEL := AP-DK01.1
|
||||
DEVICE_VARIANT := C1
|
||||
BOARD_NAME := ap-dk01.1-c1
|
||||
DEVICE_DTS := qcom-ipq4019-ap.dk01.1-c1
|
||||
KERNEL_INSTALL := 1
|
||||
KERNEL_SIZE := 4096k
|
||||
IMAGE_SIZE := 26624k
|
||||
$(call Device/FitImage)
|
||||
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += qcom_ap-dk01.1-c1
|
||||
|
||||
define Device/qcom_ap-dk04.1-c1
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := Qualcomm Atheros
|
||||
DEVICE_MODEL := AP-DK04.1
|
||||
DEVICE_VARIANT := C1
|
||||
DEVICE_DTS := qcom-ipq4019-ap.dk04.1-c1
|
||||
KERNEL_INSTALL := 1
|
||||
KERNEL_SIZE := 4048k
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
BOARD_NAME := ap-dk04.1-c1
|
||||
endef
|
||||
TARGET_DEVICES += qcom_ap-dk04.1-c1
|
||||
|
||||
define Device/qxwlan_e2600ac-c1
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := Qxwlan
|
||||
DEVICE_MODEL := E2600AC
|
||||
DEVICE_VARIANT := C1
|
||||
BOARD_NAME := e2600ac-c1
|
||||
DEVICE_DTS := qcom-ipq4019-e2600ac-c1
|
||||
KERNEL_SIZE := 4096k
|
||||
IMAGE_SIZE := 31232k
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac
|
||||
endef
|
||||
TARGET_DEVICES += qxwlan_e2600ac-c1
|
||||
|
||||
define Device/qxwlan_e2600ac-c2
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := Qxwlan
|
||||
DEVICE_MODEL := E2600AC
|
||||
DEVICE_VARIANT := C2
|
||||
DEVICE_DTS := qcom-ipq4019-e2600ac-c2
|
||||
KERNEL_INSTALL := 1
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac
|
||||
endef
|
||||
TARGET_DEVICES += qxwlan_e2600ac-c2
|
||||
|
||||
define Device/unielec_u4019-32m
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := Unielec
|
||||
DEVICE_MODEL := U4019
|
||||
DEVICE_VARIANT := 32M
|
||||
BOARD_NAME := u4019-32m
|
||||
DEVICE_DTS := qcom-ipq4019-u4019-32m
|
||||
KERNEL_SIZE := 4096k
|
||||
IMAGE_SIZE := 31232k
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += unielec_u4019-32m
|
||||
|
||||
define Device/zyxel_nbg6617
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := ZyXEL
|
||||
DEVICE_MODEL := NBG6617
|
||||
DEVICE_DTS := qcom-ipq4018-nbg6617
|
||||
KERNEL_SIZE := 4096k
|
||||
ROOTFS_SIZE := 24960k
|
||||
RAS_BOARD := NBG6617
|
||||
RAS_ROOTFS_SIZE := 19840k
|
||||
RAS_VERSION := "$(VERSION_DIST) $(REVISION)"
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
IMAGES += factory.bin
|
||||
# The ZyXEL firmware allows flashing thru the web-gui only when the rootfs is
|
||||
# at least as large as the one of the initial firmware image (not the current
|
||||
# one on the device). This only applies to the Web-UI, the bootlaoder ignores
|
||||
# this minimum-size. However, the larger image can be flashed both ways.
|
||||
IMAGE/factory.bin := append-rootfs | pad-rootfs | pad-to 64k | check-size $$$$(ROOTFS_SIZE) | zyxel-ras-image separate-kernel
|
||||
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | check-size $$$$(ROOTFS_SIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
||||
DEVICE_PACKAGES := kmod-usb-ledtrig-usbport
|
||||
endef
|
||||
TARGET_DEVICES += zyxel_nbg6617
|
||||
|
||||
define Device/zyxel_wre6606
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := ZyXEL
|
||||
DEVICE_MODEL := WRE6606
|
||||
DEVICE_DTS := qcom-ipq4018-wre6606
|
||||
DEVICE_DTS_CONFIG := config@4
|
||||
IMAGE_SIZE := 13184k
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
DEVICE_PACKAGES := -kmod-ath10k -ath10k-firmware-qca4019 \
|
||||
kmod-ath10k-ct-smallbuffers ath10k-firmware-qca4019-ct
|
||||
endef
|
||||
TARGET_DEVICES += zyxel_wre6606
|
||||
include $(SUBTARGET).mk
|
||||
|
||||
$(eval $(call BuildImage))
|
||||
|
||||
919
target/linux/ipq40xx/image/generic.mk
Normal file
919
target/linux/ipq40xx/image/generic.mk
Normal file
@ -0,0 +1,919 @@
|
||||
|
||||
DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
|
||||
DEVICE_VARS += RAS_BOARD RAS_ROOTFS_SIZE RAS_VERSION
|
||||
DEVICE_VARS += WRGG_DEVNAME WRGG_SIGNATURE
|
||||
|
||||
define Device/FitImage
|
||||
KERNEL_SUFFIX := -fit-uImage.itb
|
||||
KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
|
||||
KERNEL_NAME := Image
|
||||
endef
|
||||
|
||||
define Device/FitImageLzma
|
||||
KERNEL_SUFFIX := -fit-uImage.itb
|
||||
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb
|
||||
KERNEL_NAME := Image
|
||||
endef
|
||||
|
||||
define Device/FitzImage
|
||||
KERNEL_SUFFIX := -fit-zImage.itb
|
||||
KERNEL = kernel-bin | fit none $$(DTS_DIR)/$$(DEVICE_DTS).dtb
|
||||
KERNEL_NAME := zImage
|
||||
endef
|
||||
|
||||
define Device/UbiFit
|
||||
KERNEL_IN_UBI := 1
|
||||
IMAGES := nand-factory.ubi nand-sysupgrade.bin
|
||||
IMAGE/nand-factory.ubi := append-ubi
|
||||
IMAGE/nand-sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
endef
|
||||
|
||||
define Device/DniImage
|
||||
$(call Device/FitzImage)
|
||||
NETGEAR_BOARD_ID :=
|
||||
NETGEAR_HW_ID :=
|
||||
IMAGES += factory.img
|
||||
IMAGE/factory.img := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | netgear-dni
|
||||
IMAGE/sysupgrade.bin := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | \
|
||||
append-rootfs | pad-rootfs | check-size | append-metadata
|
||||
endef
|
||||
|
||||
define Build/append-rootfshdr
|
||||
mkimage -A $(LINUX_KARCH) \
|
||||
-O linux -T filesystem \
|
||||
-C lzma -a $(KERNEL_LOADADDR) -e $(if $(KERNEL_ENTRY),$(KERNEL_ENTRY),$(KERNEL_LOADADDR)) \
|
||||
-n root.squashfs -d $(IMAGE_ROOTFS) $@.new
|
||||
dd if=$@.new bs=64 count=1 >> $(IMAGE_KERNEL)
|
||||
endef
|
||||
|
||||
define Build/mkmylofw_32m
|
||||
$(eval device_id=$(word 1,$(1)))
|
||||
$(eval revision=$(word 2,$(1)))
|
||||
|
||||
let \
|
||||
size="$$(stat -c%s $@)" \
|
||||
pad="$(subst k,* 1024,$(BLOCKSIZE))" \
|
||||
pad="(pad - (size % pad)) % pad" \
|
||||
newsize='size + pad'; \
|
||||
$(STAGING_DIR_HOST)/bin/mkmylofw \
|
||||
-B WPE72 -i 0x11f6:$(device_id):0x11f6:$(device_id) -r $(revision) \
|
||||
-s 0x2000000 -p0x180000:$$newsize:al:0x80208000:"OpenWrt":$@ \
|
||||
$@.new
|
||||
@mv $@.new $@
|
||||
endef
|
||||
|
||||
define Build/wac5xx-netgear-tar
|
||||
mkdir $@.tmp
|
||||
mv $@ $@.tmp/wac5xx-ubifs-root.img
|
||||
md5sum $@.tmp/wac5xx-ubifs-root.img > $@.tmp/wac5xx-ubifs-root.md5sum
|
||||
echo "WAC505 WAC510" > $@.tmp/metadata.txt
|
||||
echo "WAC505_V9.9.9.9" > $@.tmp/version
|
||||
tar -C $@.tmp/ -cf $@ .
|
||||
rm -rf $@.tmp
|
||||
endef
|
||||
|
||||
define Build/qsdk-ipq-factory-nand-askey
|
||||
$(TOPDIR)/scripts/mkits-qsdk-ipq-image.sh $@.its\
|
||||
askey_kernel $(IMAGE_KERNEL) \
|
||||
askey_fs $(IMAGE_ROOTFS) \
|
||||
ubifs $@
|
||||
PATH=$(LINUX_DIR)/scripts/dtc:$(PATH) mkimage -f $@.its $@.new
|
||||
@mv $@.new $@
|
||||
endef
|
||||
|
||||
define Build/SenaoFW
|
||||
-$(STAGING_DIR_HOST)/bin/mksenaofw \
|
||||
-n $(BOARD_NAME) -r $(VENDOR_ID) -p $(1) \
|
||||
-c $(DATECODE) -w $(2) -x $(CW_VER) -t 0 \
|
||||
-e $@ \
|
||||
-o $@.new
|
||||
@cp $@.new $@
|
||||
endef
|
||||
|
||||
define Build/wrgg-image
|
||||
mkwrggimg -i $@ \
|
||||
-o $@.new \
|
||||
-d "$(WRGG_DEVNAME)" \
|
||||
-s "$(WRGG_SIGNATURE)" \
|
||||
-v "" -m "" -B ""
|
||||
mv $@.new $@
|
||||
endef
|
||||
|
||||
define Device/8dev_habanero-dvk
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := 8devices
|
||||
DEVICE_MODEL := Habanero DVK
|
||||
IMAGE_SIZE := 30976k
|
||||
SOC := qcom-ipq4019
|
||||
DEVICE_PACKAGES := ipq-wifi-8dev_habanero-dvk
|
||||
IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | append-rootfs | pad-rootfs | check-size | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += 8dev_habanero-dvk
|
||||
|
||||
define Device/8dev_jalapeno-common
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
SOC := qcom-ipq4018
|
||||
endef
|
||||
|
||||
define Device/8dev_jalapeno
|
||||
$(call Device/8dev_jalapeno-common)
|
||||
DEVICE_VENDOR := 8devices
|
||||
DEVICE_MODEL := Jalapeno
|
||||
endef
|
||||
TARGET_DEVICES += 8dev_jalapeno
|
||||
|
||||
define Device/alfa-network_ap120c-ac
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := ALFA Network
|
||||
DEVICE_MODEL := AP120C-AC
|
||||
SOC := qcom-ipq4018
|
||||
DEVICE_PACKAGES := kmod-usb-acm kmod-tpm-i2c-atmel
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
IMAGE_SIZE := 65536k
|
||||
IMAGES := nand-factory.bin nand-sysupgrade.bin
|
||||
IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
|
||||
endef
|
||||
TARGET_DEVICES += alfa-network_ap120c-ac
|
||||
|
||||
define Device/aruba_glenmorangie
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := Aruba
|
||||
SOC := qcom-ipq4029
|
||||
DEVICE_PACKAGES := ipq-wifi-aruba_ap-303
|
||||
endef
|
||||
|
||||
define Device/aruba_ap-303
|
||||
$(call Device/aruba_glenmorangie)
|
||||
DEVICE_MODEL := AP-303
|
||||
endef
|
||||
TARGET_DEVICES += aruba_ap-303
|
||||
|
||||
define Device/aruba_ap-303h
|
||||
$(call Device/aruba_glenmorangie)
|
||||
DEVICE_MODEL := AP-303H
|
||||
endef
|
||||
TARGET_DEVICES += aruba_ap-303h
|
||||
|
||||
define Device/aruba_ap-365
|
||||
$(call Device/aruba_glenmorangie)
|
||||
DEVICE_MODEL := AP-365
|
||||
DEVICE_PACKAGES += kmod-hwmon-ad7418
|
||||
endef
|
||||
TARGET_DEVICES += aruba_ap-365
|
||||
|
||||
define Device/asus_map-ac2200
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := ASUS
|
||||
DEVICE_MODEL := Lyra (MAP-AC2200)
|
||||
SOC := qcom-ipq4019
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct kmod-ath3k
|
||||
endef
|
||||
TARGET_DEVICES += asus_map-ac2200
|
||||
|
||||
define Device/asus_rt-ac58u
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := ASUS
|
||||
DEVICE_MODEL := RT-AC58U
|
||||
SOC := qcom-ipq4018
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DTB_SIZE := 65536
|
||||
IMAGE_SIZE := 20439364
|
||||
FILESYSTEMS := squashfs
|
||||
# Someone - in their infinite wisdom - decided to put the firmware
|
||||
# version in front of the image name \03\00\00\04 => Version 3.0.0.4
|
||||
# Since u-boot works with strings we either need another fixup step
|
||||
# to add a version... or we are very careful not to add '\0' into that
|
||||
# string and call it a day.... Yeah, we do the latter!
|
||||
UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC58U')
|
||||
DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers \
|
||||
kmod-usb-ledtrig-usbport
|
||||
endef
|
||||
TARGET_DEVICES += asus_rt-ac58u
|
||||
|
||||
define Device/asus_rt-acrh17
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := ASUS
|
||||
DEVICE_MODEL := RT-ACRH17
|
||||
SOC := qcom-ipq4019
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DTB_SIZE := 65536
|
||||
IMAGE_SIZE := 20439364
|
||||
FILESYSTEMS := squashfs
|
||||
UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC82U')
|
||||
KERNEL_INITRAMFS := $$(KERNEL) | uImage none
|
||||
KERNEL_INITRAMFS_SUFFIX := -factory.trx
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct ipq-wifi-asus_rt-acrh17 kmod-usb-ledtrig-usbport
|
||||
endef
|
||||
TARGET_DEVICES += asus_rt-acrh17
|
||||
|
||||
define Device/avm_fritzbox-4040
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := AVM
|
||||
DEVICE_MODEL := FRITZ!Box 4040
|
||||
SOC := qcom-ipq4018
|
||||
BOARD_NAME := fritz4040
|
||||
IMAGE_SIZE := 29056k
|
||||
UBOOT_PATH := $(STAGING_DIR_IMAGE)/uboot-fritz4040.bin
|
||||
UBOOT_PARTITION_SIZE := 524288
|
||||
IMAGES += eva.bin
|
||||
IMAGE/eva.bin := append-uboot | pad-to $$$$(UBOOT_PARTITION_SIZE) | append-kernel | append-rootfs | pad-rootfs
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata
|
||||
DEVICE_PACKAGES := fritz-tffs fritz-caldata
|
||||
endef
|
||||
TARGET_DEVICES += avm_fritzbox-4040
|
||||
|
||||
define Device/avm_fritzbox-7530
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := AVM
|
||||
DEVICE_MODEL := FRITZ!Box 7530
|
||||
SOC := qcom-ipq4019
|
||||
DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand
|
||||
endef
|
||||
TARGET_DEVICES += avm_fritzbox-7530
|
||||
|
||||
define Device/avm_fritzrepeater-1200
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := AVM
|
||||
DEVICE_MODEL := FRITZ!Repeater 1200
|
||||
SOC := qcom-ipq4019
|
||||
DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand ipq-wifi-avm_fritzrepeater-1200
|
||||
endef
|
||||
TARGET_DEVICES += avm_fritzrepeater-1200
|
||||
|
||||
define Device/avm_fritzrepeater-3000
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := AVM
|
||||
DEVICE_MODEL := FRITZ!Repeater 3000
|
||||
SOC := qcom-ipq4019
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct fritz-caldata fritz-tffs-nand
|
||||
endef
|
||||
TARGET_DEVICES += avm_fritzrepeater-3000
|
||||
|
||||
define Device/buffalo_wtr-m2133hp
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := Buffalo
|
||||
DEVICE_MODEL := WTR-M2133HP
|
||||
SOC := qcom-ipq4019
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct ipq-wifi-buffalo_wtr-m2133hp
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
endef
|
||||
TARGET_DEVICES += buffalo_wtr-m2133hp
|
||||
|
||||
define Device/cellc_rtl30vw
|
||||
KERNEL_SUFFIX := -fit-uImage.itb
|
||||
KERNEL_INITRAMFS = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
|
||||
KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb | uImage lzma | pad-to 2048
|
||||
KERNEL_NAME := Image
|
||||
KERNEL_IN_UBI :=
|
||||
IMAGES := nand-factory.bin nand-sysupgrade.bin
|
||||
IMAGE/nand-factory.bin := append-rootfshdr | append-ubi | qsdk-ipq-factory-nand-askey
|
||||
IMAGE/nand-sysupgrade.bin := append-rootfshdr | sysupgrade-tar | append-metadata
|
||||
DEVICE_VENDOR := Cell C
|
||||
DEVICE_MODEL := RTL30VW
|
||||
SOC := qcom-ipq4019
|
||||
DEVICE_DTS_CONFIG := config@5
|
||||
KERNEL_INSTALL := 1
|
||||
KERNEL_SIZE := 4096k
|
||||
IMAGE_SIZE := 57344k
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_PACKAGES := kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi ipq-wifi-cellc_rtl30vw
|
||||
endef
|
||||
TARGET_DEVICES += cellc_rtl30vw
|
||||
|
||||
define Device/century_wr142ac-common
|
||||
$(call Device/FitzImage)
|
||||
DEVICE_VENDOR := Century
|
||||
DEVICE_MODEL := WR142AC
|
||||
SOC := qcom-ipq4019
|
||||
DEVICE_PACKAGES := ipq-wifi-century_wr142ac kmod-usb-ledtrig-usbport
|
||||
endef
|
||||
|
||||
define Device/century_wr142ac
|
||||
$(call Device/century_wr142ac-common)
|
||||
KERNEL_SIZE := 4096k
|
||||
IMAGE_SIZE := 31232k
|
||||
IMAGES += factory.bin
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size
|
||||
endef
|
||||
TARGET_DEVICES += century_wr142ac
|
||||
|
||||
define Device/century_wr142ac-nand
|
||||
$(call Device/century_wr142ac-common)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VARIANT := NAND
|
||||
DEVICE_DTS_CONFIG := config@10
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
endef
|
||||
TARGET_DEVICES += century_wr142ac-nand
|
||||
|
||||
define Device/cilab_meshpoint-one
|
||||
$(call Device/8dev_jalapeno-common)
|
||||
DEVICE_VENDOR := Crisis Innovation Lab
|
||||
DEVICE_MODEL := MeshPoint.One
|
||||
DEVICE_PACKAGES := kmod-i2c-gpio kmod-iio-bmp280-i2c kmod-hwmon-ina2xx kmod-rtc-pcf2127
|
||||
endef
|
||||
TARGET_DEVICES += cilab_meshpoint-one
|
||||
|
||||
define Device/compex_wpj419
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := Compex
|
||||
DEVICE_MODEL := WPJ419
|
||||
SOC := qcom-ipq4019
|
||||
DEVICE_DTS_CONFIG := config@12
|
||||
KERNEL_INSTALL := 1
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
FILESYSTEMS := squashfs
|
||||
endef
|
||||
TARGET_DEVICES += compex_wpj419
|
||||
|
||||
define Device/compex_wpj428
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := Compex
|
||||
DEVICE_MODEL := WPJ428
|
||||
SOC := qcom-ipq4028
|
||||
DEVICE_DTS_CONFIG := config@4
|
||||
BLOCKSIZE := 64k
|
||||
IMAGE_SIZE := 31232k
|
||||
KERNEL_SIZE := 4096k
|
||||
IMAGES += cpximg-6a04.bin
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
IMAGE/cpximg-6a04.bin := append-kernel | append-rootfs | pad-rootfs | mkmylofw_32m 0x8A2 3
|
||||
DEVICE_PACKAGES := kmod-gpio-beeper
|
||||
endef
|
||||
TARGET_DEVICES += compex_wpj428
|
||||
|
||||
define Device/devolo_magic-2-wifi-next
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := devolo
|
||||
DEVICE_MODEL := Magic 2 WiFi next
|
||||
SOC := qcom-ipq4018
|
||||
KERNEL_SIZE := 4096k
|
||||
|
||||
# If the bootloader sees 0xDEADC0DE and this trailer at the 64k boundary of a TFTP image
|
||||
# it will bootm it, just like we want for the initramfs.
|
||||
KERNEL_INITRAMFS := kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to 64k |\
|
||||
append-string -e '\xDE\xAD\xC0\xDE{"fl_initramfs":""}\x00'
|
||||
|
||||
IMAGE_SIZE := 26624k
|
||||
IMAGES := sysupgrade.bin
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
DEVICE_PACKAGES := ipq-wifi-devolo_magic-2-wifi-next
|
||||
endef
|
||||
TARGET_DEVICES += devolo_magic-2-wifi-next
|
||||
|
||||
define Device/dlink_dap-2610
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := D-Link
|
||||
DEVICE_MODEL := DAP-2610
|
||||
SOC := qcom-ipq4018
|
||||
DEVICE_DTS_CONFIG := config@ap.dk01.1-c1
|
||||
BLOCKSIZE := 64k
|
||||
WRGG_DEVNAME := /dev/mtdblock/8
|
||||
WRGG_SIGNATURE := wapac30_dkbs_dap2610
|
||||
IMAGE_SIZE := 14080k
|
||||
IMAGES += factory.bin
|
||||
# Bootloader expects a special 160 byte header which is added by
|
||||
# wrgg-image.
|
||||
# Factory image size must be larger than 6MB, and size in wrgg header must
|
||||
# match actual factory image size to be flashable from D-Link http server.
|
||||
# Bootloader verifies checksum of wrgg image before booting, thus jffs2
|
||||
# cannot be part of the wrgg image. This is solved in the factory image by
|
||||
# having the rootfs at the end of the image (without pad-rootfs). And in
|
||||
# the sysupgrade image only the kernel is included in the wrgg checksum,
|
||||
# but this is not flashable from the D-link http server.
|
||||
# append-rootfs must start on an erase block boundary.
|
||||
IMAGE/factory.bin := append-kernel | pad-offset 6144k 160 | append-rootfs | wrgg-image | check-size
|
||||
IMAGE/sysupgrade.bin := append-kernel | wrgg-image | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size | append-metadata
|
||||
DEVICE_PACKAGES := ipq-wifi-dlink_dap2610
|
||||
endef
|
||||
TARGET_DEVICES += dlink_dap-2610
|
||||
|
||||
define Device/edgecore_ecw5211
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := Edgecore
|
||||
DEVICE_MODEL := ECW5211
|
||||
SOC := qcom-ipq4018
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_DTS_CONFIG := config@ap.dk01.1-c2
|
||||
DEVICE_PACKAGES := kmod-tpm-i2c-atmel kmod-usb-acm
|
||||
endef
|
||||
TARGET_DEVICES += edgecore_ecw5211
|
||||
|
||||
define Device/edgecore_oap100
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := Edgecore
|
||||
DEVICE_MODEL := OAP100
|
||||
SOC := qcom-ipq4019
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
IMAGES := nand-sysupgrade.bin
|
||||
DEVICE_DTS_CONFIG := config@ap.dk07.1-c1
|
||||
DEVICE_PACKAGES := ipq-wifi-edgecore_oap100 kmod-usb-acm kmod-usb-net kmod-usb-net-cdc-qmi uqmi
|
||||
endef
|
||||
TARGET_DEVICES += edgecore_oap100
|
||||
|
||||
define Device/engenius_eap1300
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := EnGenius
|
||||
DEVICE_MODEL := EAP1300
|
||||
DEVICE_DTS_CONFIG := config@4
|
||||
BOARD_NAME := eap1300
|
||||
SOC := qcom-ipq4018
|
||||
KERNEL_SIZE := 5120k
|
||||
IMAGE_SIZE := 25344k
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += engenius_eap1300
|
||||
|
||||
define Device/engenius_eap2200
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := EnGenius
|
||||
DEVICE_MODEL := EAP2200
|
||||
SOC := qcom-ipq4019
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct ipq-wifi-engenius_eap2200 -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers
|
||||
endef
|
||||
TARGET_DEVICES += engenius_eap2200
|
||||
|
||||
define Device/engenius_emd1
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := EnGenius
|
||||
DEVICE_MODEL := EMD1
|
||||
DEVICE_DTS_CONFIG := config@4
|
||||
SOC := qcom-ipq4018
|
||||
IMAGE_SIZE := 30720k
|
||||
IMAGES += factory.bin
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size
|
||||
DEVICE_PACKAGES := ipq-wifi-engenius_emd1
|
||||
endef
|
||||
TARGET_DEVICES += engenius_emd1
|
||||
|
||||
define Device/engenius_emr3500
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := EnGenius
|
||||
DEVICE_MODEL := EMR3500
|
||||
DEVICE_DTS_CONFIG := config@4
|
||||
SOC := qcom-ipq4018
|
||||
KERNEL_SIZE := 4096k
|
||||
IMAGE_SIZE := 30720k
|
||||
IMAGES += factory.bin
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size
|
||||
DEVICE_PACKAGES := ipq-wifi-engenius_emr3500
|
||||
endef
|
||||
TARGET_DEVICES += engenius_emr3500
|
||||
|
||||
define Device/engenius_ens620ext
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := EnGenius
|
||||
DEVICE_MODEL := ENS620EXT
|
||||
SOC := qcom-ipq4018
|
||||
DEVICE_DTS_CONFIG := config@4
|
||||
BLOCKSIZE := 64k
|
||||
PAGESIZE := 256
|
||||
BOARD_NAME := ENS620EXT
|
||||
VENDOR_ID := 0x0101
|
||||
PRODUCT_ID := 0x79
|
||||
PRODUCT_ID_NEW := 0xA4
|
||||
DATECODE := 190507
|
||||
FW_VER := 3.1.2
|
||||
FW_VER_NEW := 3.5.6
|
||||
CW_VER := 1.8.99
|
||||
IMAGE_SIZE := 21312k
|
||||
KERNEL_SIZE := 5120k
|
||||
FILESYSTEMS := squashfs
|
||||
IMAGES += factory_30.bin factory_35.bin
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata
|
||||
IMAGE/factory_30.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | check-size | SenaoFW $$$$(PRODUCT_ID) $$$$(FW_VER)
|
||||
IMAGE/factory_35.bin := qsdk-ipq-factory-nor | check-size | SenaoFW $$$$(PRODUCT_ID_NEW) $$$$(FW_VER_NEW)
|
||||
endef
|
||||
TARGET_DEVICES += engenius_ens620ext
|
||||
|
||||
define Device/ezviz_cs-w3-wd1200g-eup
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := EZVIZ
|
||||
DEVICE_MODEL := CS-W3-WD1200G
|
||||
DEVICE_VARIANT := EUP
|
||||
DEVICE_DTS_CONFIG := config@4
|
||||
IMAGE_SIZE := 14848k
|
||||
SOC := qcom-ipq4018
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
|
||||
append-metadata
|
||||
DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers \
|
||||
ipq-wifi-ezviz_cs-w3-wd1200g-eup
|
||||
endef
|
||||
TARGET_DEVICES += ezviz_cs-w3-wd1200g-eup
|
||||
|
||||
define Device/glinet_gl-ap1300
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := GL.iNet
|
||||
DEVICE_MODEL := GL-AP1300
|
||||
SOC := qcom-ipq4018
|
||||
DEVICE_DTS_CONFIG := config@ap.dk01.1-c2
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
IMAGE_SIZE := 131072k
|
||||
KERNEL_INSTALL := 1
|
||||
DEVICE_PACKAGES := ipq-wifi-glinet_gl-ap1300
|
||||
endef
|
||||
TARGET_DEVICES += glinet_gl-ap1300
|
||||
|
||||
define Device/glinet_gl-b1300
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := GL.iNet
|
||||
DEVICE_MODEL := GL-B1300
|
||||
BOARD_NAME := gl-b1300
|
||||
SOC := qcom-ipq4029
|
||||
KERNEL_SIZE := 4096k
|
||||
IMAGE_SIZE := 26624k
|
||||
IMAGE/sysupgrade.bin := append-kernel |append-rootfs | pad-rootfs | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += glinet_gl-b1300
|
||||
|
||||
define Device/glinet_gl-s1300
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := GL.iNet
|
||||
DEVICE_MODEL := GL-S1300
|
||||
SOC := qcom-ipq4029
|
||||
KERNEL_SIZE := 4096k
|
||||
IMAGE_SIZE := 26624k
|
||||
IMAGES := sysupgrade.bin
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
DEVICE_PACKAGES := ipq-wifi-glinet_gl-s1300 kmod-fs-ext4 kmod-mmc kmod-spi-dev
|
||||
endef
|
||||
TARGET_DEVICES += glinet_gl-s1300
|
||||
|
||||
define Device/hiwifi_c526a
|
||||
$(call Device/FitzImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := HiWiFi
|
||||
DEVICE_MODEL := C526A
|
||||
SOC := qcom-ipq4019
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_PACKAGES := ipq-wifi-hiwifi_c526a kmod-mt7615e kmod-mt7615-firmware
|
||||
endef
|
||||
TARGET_DEVICES += hiwifi_c526a
|
||||
|
||||
define Device/hiwifi_c526a-128m
|
||||
$(call Device/hiwifi_c526a)
|
||||
DEVICE_VARIANT := 128M
|
||||
endef
|
||||
TARGET_DEVICES += hiwifi_c526a-128m
|
||||
|
||||
define Device/linksys_ea6350v3
|
||||
# The Linksys EA6350v3 has a uboot bootloader that does not
|
||||
# support either booting lzma kernel images nor booting UBI
|
||||
# partitions. This uboot, however, supports raw kernel images and
|
||||
# gzipped images.
|
||||
#
|
||||
# As for the time of writing this, the device will boot the kernel
|
||||
# from a fixed address with a fixed length of 3MiB. Also, the
|
||||
# device has a hard-coded kernel command line that requieres the
|
||||
# rootfs and alt_rootfs to be in mtd11 and mtd13 respectively.
|
||||
# Oh... and the kernel partition overlaps with the rootfs
|
||||
# partition (the same for alt_kernel and alt_rootfs).
|
||||
#
|
||||
# If you are planing re-partitioning the device, you may want to
|
||||
# keep those details in mind:
|
||||
# 1. The kernel adresses you should honor are 0x00000000 and
|
||||
# 0x02800000 respectively.
|
||||
# 2. The kernel size (plus the dtb) cannot exceed 3.00MiB in size.
|
||||
# 3. You can use 'zImage', but not a raw 'Image' packed with lzma.
|
||||
# 4. The kernel command line from uboot is harcoded to boot with
|
||||
# rootfs either in mtd11 or mtd13.
|
||||
$(call Device/FitzImage)
|
||||
DEVICE_VENDOR := Linksys
|
||||
DEVICE_MODEL := EA6350
|
||||
DEVICE_VARIANT := v3
|
||||
SOC := qcom-ipq4018
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
KERNEL_SIZE := 3072k
|
||||
IMAGE_SIZE := 37888k
|
||||
UBINIZE_OPTS := -E 5
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-kernel | append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=EA6350v3
|
||||
endef
|
||||
TARGET_DEVICES += linksys_ea6350v3
|
||||
|
||||
define Device/linksys_ea8300
|
||||
$(call Device/FitzImage)
|
||||
DEVICE_VENDOR := Linksys
|
||||
DEVICE_MODEL := EA8300
|
||||
SOC := qcom-ipq4019
|
||||
KERNEL_SIZE := 3072k
|
||||
IMAGE_SIZE := 87040k
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=EA8300
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct ipq-wifi-linksys_ea8300 kmod-usb-ledtrig-usbport
|
||||
endef
|
||||
TARGET_DEVICES += linksys_ea8300
|
||||
|
||||
define Device/linksys_mr8300
|
||||
$(call Device/FitzImage)
|
||||
DEVICE_VENDOR := Linksys
|
||||
DEVICE_MODEL := MR8300
|
||||
SOC := qcom-ipq4019
|
||||
KERNEL_SIZE := 3072k
|
||||
IMAGE_SIZE := 87040k
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=MR8300
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct ipq-wifi-linksys_mr8300-v0 kmod-usb-ledtrig-usbport
|
||||
endef
|
||||
TARGET_DEVICES += linksys_mr8300
|
||||
|
||||
define Device/luma_wrtq-329acn
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := Luma Home
|
||||
DEVICE_MODEL := WRTQ-329ACN
|
||||
SOC := qcom-ipq4018
|
||||
DEVICE_PACKAGES := ipq-wifi-luma_wrtq-329acn kmod-ath3k kmod-eeprom-at24 kmod-i2c-gpio
|
||||
IMAGE_SIZE := 76632k
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
endef
|
||||
TARGET_DEVICES += luma_wrtq-329acn
|
||||
|
||||
define Device/meraki_mr33
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := Cisco Meraki
|
||||
DEVICE_MODEL := MR33
|
||||
SOC := qcom-ipq4029
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_PACKAGES := -swconfig ath10k-firmware-qca9887-ct
|
||||
endef
|
||||
TARGET_DEVICES += meraki_mr33
|
||||
|
||||
define Device/mobipromo_cm520-79f
|
||||
$(call Device/FitzImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := MobiPromo
|
||||
DEVICE_MODEL := CM520-79F
|
||||
SOC := qcom-ipq4019
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_PACKAGES := ipq-wifi-mobipromo_cm520-79f kmod-usb-ledtrig-usbport
|
||||
endef
|
||||
TARGET_DEVICES += mobipromo_cm520-79f
|
||||
|
||||
define Device/netgear_ex61x0v2
|
||||
$(call Device/DniImage)
|
||||
DEVICE_VENDOR := NETGEAR
|
||||
DEVICE_DTS_CONFIG := config@4
|
||||
NETGEAR_BOARD_ID := EX6150v2series
|
||||
NETGEAR_HW_ID := 29765285+16+0+128+2x2
|
||||
IMAGE_SIZE := 14400k
|
||||
SOC := qcom-ipq4018
|
||||
endef
|
||||
|
||||
define Device/netgear_ex6100v2
|
||||
$(call Device/netgear_ex61x0v2)
|
||||
DEVICE_MODEL := EX6100
|
||||
DEVICE_VARIANT := v2
|
||||
endef
|
||||
TARGET_DEVICES += netgear_ex6100v2
|
||||
|
||||
define Device/netgear_ex6150v2
|
||||
$(call Device/netgear_ex61x0v2)
|
||||
DEVICE_MODEL := EX6150
|
||||
DEVICE_VARIANT := v2
|
||||
endef
|
||||
TARGET_DEVICES += netgear_ex6150v2
|
||||
|
||||
define Device/netgear_ex6200v2
|
||||
$(call Device/DniImage)
|
||||
DEVICE_DTS_CONFIG := config@4
|
||||
NETGEAR_HW_ID := 29765265+16+0+256+2x2+2x2
|
||||
DEVICE_VENDOR := Netgear
|
||||
DEVICE_MODEL := EX6200
|
||||
DEVICE_VARIANT := v2
|
||||
SOC := qcom-ipq4018
|
||||
DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport
|
||||
endef
|
||||
TARGET_DEVICES += netgear_ex6200v2
|
||||
|
||||
define Device/netgear_wac510
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := Netgear
|
||||
DEVICE_MODEL := WAC510
|
||||
SOC := qcom-ipq4018
|
||||
DEVICE_DTS_CONFIG := config@5
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
IMAGES += nand-factory.tar
|
||||
IMAGE/nand-factory.tar := append-ubi | wac5xx-netgear-tar
|
||||
DEVICE_PACKAGES := uboot-envtools
|
||||
endef
|
||||
TARGET_DEVICES += netgear_wac510
|
||||
|
||||
define Device/openmesh_a42
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := OpenMesh
|
||||
DEVICE_MODEL := A42
|
||||
SOC := qcom-ipq4018
|
||||
DEVICE_DTS_CONFIG := config@om.a42
|
||||
BLOCKSIZE := 64k
|
||||
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
|
||||
IMAGE_SIZE := 15616k
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A42
|
||||
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += openmesh_a42
|
||||
|
||||
define Device/openmesh_a62
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := OpenMesh
|
||||
DEVICE_MODEL := A62
|
||||
SOC := qcom-ipq4019
|
||||
DEVICE_DTS_CONFIG := config@om.a62
|
||||
BLOCKSIZE := 64k
|
||||
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
|
||||
IMAGE_SIZE := 15552k
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A62
|
||||
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct
|
||||
endef
|
||||
TARGET_DEVICES += openmesh_a62
|
||||
|
||||
define Device/plasmacloud_pa1200
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := Plasma Cloud
|
||||
DEVICE_MODEL := PA1200
|
||||
SOC := qcom-ipq4018
|
||||
DEVICE_DTS_CONFIG := config@pc.pa1200
|
||||
BLOCKSIZE := 64k
|
||||
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
|
||||
IMAGE_SIZE := 15616k
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=PA1200
|
||||
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
||||
DEVICE_PACKAGES := ipq-wifi-plasmacloud_pa1200
|
||||
endef
|
||||
TARGET_DEVICES += plasmacloud_pa1200
|
||||
|
||||
define Device/plasmacloud_pa2200
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := Plasma Cloud
|
||||
DEVICE_MODEL := PA2200
|
||||
SOC := qcom-ipq4019
|
||||
DEVICE_DTS_CONFIG := config@pc.pa2200
|
||||
BLOCKSIZE := 64k
|
||||
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
|
||||
IMAGE_SIZE := 15552k
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=PA2200
|
||||
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct ipq-wifi-plasmacloud_pa2200
|
||||
endef
|
||||
TARGET_DEVICES += plasmacloud_pa2200
|
||||
|
||||
define Device/p2w_r619ac
|
||||
$(call Device/FitzImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := P&W
|
||||
DEVICE_MODEL := R619AC
|
||||
SOC := qcom-ipq4019
|
||||
DEVICE_DTS_CONFIG := config@10
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_PACKAGES := ipq-wifi-p2w_r619ac
|
||||
endef
|
||||
TARGET_DEVICES += p2w_r619ac
|
||||
|
||||
define Device/qcom_ap-dk01.1-c1
|
||||
DEVICE_VENDOR := Qualcomm Atheros
|
||||
DEVICE_MODEL := AP-DK01.1
|
||||
DEVICE_VARIANT := C1
|
||||
BOARD_NAME := ap-dk01.1-c1
|
||||
SOC := qcom-ipq4019
|
||||
DEVICE_DTS := qcom-ipq4019-ap.dk01.1-c1
|
||||
KERNEL_INSTALL := 1
|
||||
KERNEL_SIZE := 4096k
|
||||
IMAGE_SIZE := 26624k
|
||||
$(call Device/FitImage)
|
||||
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += qcom_ap-dk01.1-c1
|
||||
|
||||
define Device/qcom_ap-dk04.1-c1
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := Qualcomm Atheros
|
||||
DEVICE_MODEL := AP-DK04.1
|
||||
DEVICE_VARIANT := C1
|
||||
SOC := qcom-ipq4019
|
||||
DEVICE_DTS := qcom-ipq4019-ap.dk04.1-c1
|
||||
KERNEL_INSTALL := 1
|
||||
KERNEL_SIZE := 4048k
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
BOARD_NAME := ap-dk04.1-c1
|
||||
endef
|
||||
TARGET_DEVICES += qcom_ap-dk04.1-c1
|
||||
|
||||
define Device/qxwlan_e2600ac-c1
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := Qxwlan
|
||||
DEVICE_MODEL := E2600AC
|
||||
DEVICE_VARIANT := C1
|
||||
BOARD_NAME := e2600ac-c1
|
||||
SOC := qcom-ipq4019
|
||||
KERNEL_SIZE := 4096k
|
||||
IMAGE_SIZE := 31232k
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac
|
||||
endef
|
||||
TARGET_DEVICES += qxwlan_e2600ac-c1
|
||||
|
||||
define Device/qxwlan_e2600ac-c2
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := Qxwlan
|
||||
DEVICE_MODEL := E2600AC
|
||||
DEVICE_VARIANT := C2
|
||||
SOC := qcom-ipq4019
|
||||
KERNEL_INSTALL := 1
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac
|
||||
endef
|
||||
TARGET_DEVICES += qxwlan_e2600ac-c2
|
||||
|
||||
define Device/unielec_u4019-32m
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := Unielec
|
||||
DEVICE_MODEL := U4019
|
||||
DEVICE_VARIANT := 32M
|
||||
BOARD_NAME := u4019-32m
|
||||
SOC := qcom-ipq4019
|
||||
KERNEL_SIZE := 4096k
|
||||
IMAGE_SIZE := 31232k
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += unielec_u4019-32m
|
||||
|
||||
define Device/zyxel_nbg6617
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_VENDOR := ZyXEL
|
||||
DEVICE_MODEL := NBG6617
|
||||
SOC := qcom-ipq4018
|
||||
KERNEL_SIZE := 4096k
|
||||
ROOTFS_SIZE := 24960k
|
||||
RAS_BOARD := NBG6617
|
||||
RAS_ROOTFS_SIZE := 19840k
|
||||
RAS_VERSION := "$(VERSION_DIST) $(REVISION)"
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
IMAGES += factory.bin
|
||||
# The ZyXEL firmware allows flashing thru the web-gui only when the rootfs is
|
||||
# at least as large as the one of the initial firmware image (not the current
|
||||
# one on the device). This only applies to the Web-UI, the bootlaoder ignores
|
||||
# this minimum-size. However, the larger image can be flashed both ways.
|
||||
IMAGE/factory.bin := append-rootfs | pad-rootfs | pad-to 64k | check-size $$$$(ROOTFS_SIZE) | zyxel-ras-image separate-kernel
|
||||
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | check-size $$$$(ROOTFS_SIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
||||
DEVICE_PACKAGES := kmod-usb-ledtrig-usbport
|
||||
endef
|
||||
TARGET_DEVICES += zyxel_nbg6617
|
||||
|
||||
define Device/zyxel_wre6606
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := ZyXEL
|
||||
DEVICE_MODEL := WRE6606
|
||||
DEVICE_DTS_CONFIG := config@4
|
||||
SOC := qcom-ipq4018
|
||||
IMAGE_SIZE := 13184k
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata
|
||||
DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers
|
||||
endef
|
||||
TARGET_DEVICES += zyxel_wre6606
|
||||
28
target/linux/ipq40xx/image/mikrotik.mk
Normal file
28
target/linux/ipq40xx/image/mikrotik.mk
Normal file
@ -0,0 +1,28 @@
|
||||
define Device/mikrotik_nor
|
||||
DEVICE_VENDOR := MikroTik
|
||||
BLOCKSIZE := 64k
|
||||
IMAGE_SIZE := 16128k
|
||||
KERNEL_NAME := vmlinux
|
||||
KERNEL := kernel-bin | append-dtb-elf
|
||||
IMAGES = sysupgrade.bin
|
||||
IMAGE/sysupgrade.bin := append-kernel | kernel2minor -s 1024 | \
|
||||
pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | \
|
||||
check-size | append-metadata
|
||||
endef
|
||||
|
||||
define Device/mikrotik_hap-ac2
|
||||
$(call Device/mikrotik_nor)
|
||||
DEVICE_MODEL := hAP ac2
|
||||
SOC := qcom-ipq4018
|
||||
DEVICE_PACKAGES := ipq-wifi-mikrotik_hap-ac2 -kmod-ath10k-ct \
|
||||
kmod-ath10k-ct-smallbuffers
|
||||
endef
|
||||
TARGET_DEVICES += mikrotik_hap-ac2
|
||||
|
||||
define Device/mikrotik_sxtsq-5-ac
|
||||
$(call Device/mikrotik_nor)
|
||||
DEVICE_MODEL := SXTsq 5 ac (RBSXTsqG-5acD)
|
||||
SOC := qcom-ipq4018
|
||||
DEVICE_PACKAGES := ipq-wifi-mikrotik_sxtsq-5-ac rssileds
|
||||
endef
|
||||
TARGET_DEVICES += mikrotik_sxtsq-5-ac
|
||||
4
target/linux/ipq40xx/mikrotik/config-default
Normal file
4
target/linux/ipq40xx/mikrotik/config-default
Normal file
@ -0,0 +1,4 @@
|
||||
CONFIG_MIKROTIK=y
|
||||
CONFIG_MIKROTIK_RB_SYSFS=y
|
||||
CONFIG_MTD_ROUTERBOOT_PARTS=y
|
||||
CONFIG_MTD_SPLIT_MINOR_FW=y
|
||||
4
target/linux/ipq40xx/mikrotik/target.mk
Normal file
4
target/linux/ipq40xx/mikrotik/target.mk
Normal file
@ -0,0 +1,4 @@
|
||||
BOARDNAME:=MikroTik
|
||||
FEATURES += minor
|
||||
KERNEL_IMAGES:=vmlinux
|
||||
IMAGES_DIR:=compressed
|
||||
@ -0,0 +1,165 @@
|
||||
From 4267880319bc1a2270d352e0ded6d6386242a7ef Mon Sep 17 00:00:00 2001
|
||||
From: John Crispin <blogic@openwrt.org>
|
||||
Date: Tue, 12 Aug 2014 20:49:27 +0200
|
||||
Subject: [PATCH 24/53] GPIO: add named gpio exports
|
||||
|
||||
Signed-off-by: John Crispin <blogic@openwrt.org>
|
||||
---
|
||||
drivers/gpio/gpiolib-of.c | 68 +++++++++++++++++++++++++++++++++++++++++
|
||||
drivers/gpio/gpiolib-sysfs.c | 10 +++++-
|
||||
include/asm-generic/gpio.h | 6 ++++
|
||||
include/linux/gpio/consumer.h | 8 +++++
|
||||
4 files changed, 91 insertions(+), 1 deletion(-)
|
||||
|
||||
--- a/drivers/gpio/gpiolib-of.c
|
||||
+++ b/drivers/gpio/gpiolib-of.c
|
||||
@@ -19,6 +19,8 @@
|
||||
#include <linux/pinctrl/pinctrl.h>
|
||||
#include <linux/slab.h>
|
||||
#include <linux/gpio/machine.h>
|
||||
+#include <linux/init.h>
|
||||
+#include <linux/platform_device.h>
|
||||
|
||||
#include "gpiolib.h"
|
||||
#include "gpiolib-of.h"
|
||||
@@ -915,3 +917,68 @@ void of_gpiochip_remove(struct gpio_chip
|
||||
{
|
||||
of_node_put(chip->of_node);
|
||||
}
|
||||
+
|
||||
+static struct of_device_id gpio_export_ids[] = {
|
||||
+ { .compatible = "gpio-export" },
|
||||
+ { /* sentinel */ }
|
||||
+};
|
||||
+
|
||||
+static int of_gpio_export_probe(struct platform_device *pdev)
|
||||
+{
|
||||
+ struct device_node *np = pdev->dev.of_node;
|
||||
+ struct device_node *cnp;
|
||||
+ u32 val;
|
||||
+ int nb = 0;
|
||||
+
|
||||
+ for_each_child_of_node(np, cnp) {
|
||||
+ const char *name = NULL;
|
||||
+ int gpio;
|
||||
+ bool dmc;
|
||||
+ int max_gpio = 1;
|
||||
+ int i;
|
||||
+
|
||||
+ of_property_read_string(cnp, "gpio-export,name", &name);
|
||||
+
|
||||
+ if (!name)
|
||||
+ max_gpio = of_gpio_count(cnp);
|
||||
+
|
||||
+ for (i = 0; i < max_gpio; i++) {
|
||||
+ unsigned flags = 0;
|
||||
+ enum of_gpio_flags of_flags;
|
||||
+
|
||||
+ gpio = of_get_gpio_flags(cnp, i, &of_flags);
|
||||
+ if (!gpio_is_valid(gpio))
|
||||
+ return gpio;
|
||||
+
|
||||
+ if (of_flags == OF_GPIO_ACTIVE_LOW)
|
||||
+ flags |= GPIOF_ACTIVE_LOW;
|
||||
+
|
||||
+ if (!of_property_read_u32(cnp, "gpio-export,output", &val))
|
||||
+ flags |= val ? GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW;
|
||||
+ else
|
||||
+ flags |= GPIOF_IN;
|
||||
+
|
||||
+ if (devm_gpio_request_one(&pdev->dev, gpio, flags, name ? name : of_node_full_name(np)))
|
||||
+ continue;
|
||||
+
|
||||
+ dmc = of_property_read_bool(cnp, "gpio-export,direction_may_change");
|
||||
+ gpio_export_with_name(gpio, dmc, name);
|
||||
+ nb++;
|
||||
+ }
|
||||
+ }
|
||||
+
|
||||
+ dev_info(&pdev->dev, "%d gpio(s) exported\n", nb);
|
||||
+
|
||||
+ return 0;
|
||||
+}
|
||||
+
|
||||
+static struct platform_driver gpio_export_driver = {
|
||||
+ .driver = {
|
||||
+ .name = "gpio-export",
|
||||
+ .owner = THIS_MODULE,
|
||||
+ .of_match_table = of_match_ptr(gpio_export_ids),
|
||||
+ },
|
||||
+ .probe = of_gpio_export_probe,
|
||||
+};
|
||||
+
|
||||
+module_platform_driver(gpio_export_driver);
|
||||
--- a/drivers/gpio/gpiolib-sysfs.c
|
||||
+++ b/drivers/gpio/gpiolib-sysfs.c
|
||||
@@ -571,7 +571,7 @@ static struct class gpio_class = {
|
||||
*
|
||||
* Returns zero on success, else an error.
|
||||
*/
|
||||
-int gpiod_export(struct gpio_desc *desc, bool direction_may_change)
|
||||
+int __gpiod_export(struct gpio_desc *desc, bool direction_may_change, const char *name)
|
||||
{
|
||||
struct gpio_chip *chip;
|
||||
struct gpio_device *gdev;
|
||||
@@ -633,6 +633,8 @@ int gpiod_export(struct gpio_desc *desc,
|
||||
offset = gpio_chip_hwgpio(desc);
|
||||
if (chip->names && chip->names[offset])
|
||||
ioname = chip->names[offset];
|
||||
+ if (name)
|
||||
+ ioname = name;
|
||||
|
||||
dev = device_create_with_groups(&gpio_class, &gdev->dev,
|
||||
MKDEV(0, 0), data, gpio_groups,
|
||||
@@ -654,6 +656,12 @@ err_unlock:
|
||||
gpiod_dbg(desc, "%s: status %d\n", __func__, status);
|
||||
return status;
|
||||
}
|
||||
+EXPORT_SYMBOL_GPL(__gpiod_export);
|
||||
+
|
||||
+int gpiod_export(struct gpio_desc *desc, bool direction_may_change)
|
||||
+{
|
||||
+ return __gpiod_export(desc, direction_may_change, NULL);
|
||||
+}
|
||||
EXPORT_SYMBOL_GPL(gpiod_export);
|
||||
|
||||
static int match_export(struct device *dev, const void *desc)
|
||||
--- a/include/asm-generic/gpio.h
|
||||
+++ b/include/asm-generic/gpio.h
|
||||
@@ -127,6 +127,12 @@ static inline int gpio_export(unsigned g
|
||||
return gpiod_export(gpio_to_desc(gpio), direction_may_change);
|
||||
}
|
||||
|
||||
+int __gpiod_export(struct gpio_desc *desc, bool direction_may_change, const char *name);
|
||||
+static inline int gpio_export_with_name(unsigned gpio, bool direction_may_change, const char *name)
|
||||
+{
|
||||
+ return __gpiod_export(gpio_to_desc(gpio), direction_may_change, name);
|
||||
+}
|
||||
+
|
||||
static inline int gpio_export_link(struct device *dev, const char *name,
|
||||
unsigned gpio)
|
||||
{
|
||||
--- a/include/linux/gpio/consumer.h
|
||||
+++ b/include/linux/gpio/consumer.h
|
||||
@@ -668,6 +668,7 @@ static inline void devm_acpi_dev_remove_
|
||||
|
||||
#if IS_ENABLED(CONFIG_GPIOLIB) && IS_ENABLED(CONFIG_GPIO_SYSFS)
|
||||
|
||||
+int _gpiod_export(struct gpio_desc *desc, bool direction_may_change, const char *name);
|
||||
int gpiod_export(struct gpio_desc *desc, bool direction_may_change);
|
||||
int gpiod_export_link(struct device *dev, const char *name,
|
||||
struct gpio_desc *desc);
|
||||
@@ -675,6 +676,13 @@ void gpiod_unexport(struct gpio_desc *de
|
||||
|
||||
#else /* CONFIG_GPIOLIB && CONFIG_GPIO_SYSFS */
|
||||
|
||||
+static inline int _gpiod_export(struct gpio_desc *desc,
|
||||
+ bool direction_may_change,
|
||||
+ const char *name)
|
||||
+{
|
||||
+ return -ENOSYS;
|
||||
+}
|
||||
+
|
||||
static inline int gpiod_export(struct gpio_desc *desc,
|
||||
bool direction_may_change)
|
||||
{
|
||||
@ -0,0 +1,48 @@
|
||||
From 0843a61d6913bdac8889eb048ed89f7903059787 Mon Sep 17 00:00:00 2001
|
||||
From: Robert Marko <robimarko@gmail.com>
|
||||
Date: Fri, 30 Oct 2020 13:36:31 +0100
|
||||
Subject: [PATCH] arm: compressed: add appended DTB section
|
||||
|
||||
This adds a appended_dtb section to the ARM decompressor
|
||||
linker script.
|
||||
|
||||
This allows using the existing ARM zImage appended DTB support for
|
||||
appending a DTB to the raw ELF kernel.
|
||||
|
||||
Its size is set to 1MB max to match the zImage appended DTB size limit.
|
||||
|
||||
To use it to pass the DTB to the kernel, objcopy is used:
|
||||
|
||||
objcopy --set-section-flags=.appended_dtb=alloc,contents \
|
||||
--update-section=.appended_dtb=<target>.dtb vmlinux
|
||||
|
||||
This is based off the following patch:
|
||||
https://github.com/openwrt/openwrt/commit/c063e27e02a9dcac0e7f5877fb154e58fa3e1a69
|
||||
|
||||
Signed-off-by: Robert Marko <robimarko@gmail.com>
|
||||
---
|
||||
arch/arm/boot/compressed/vmlinux.lds.S | 9 ++++++++-
|
||||
1 file changed, 8 insertions(+), 1 deletion(-)
|
||||
|
||||
--- a/arch/arm/boot/compressed/vmlinux.lds.S
|
||||
+++ b/arch/arm/boot/compressed/vmlinux.lds.S
|
||||
@@ -93,6 +93,13 @@ SECTIONS
|
||||
|
||||
_edata = .;
|
||||
|
||||
+ .appended_dtb : {
|
||||
+ /* leave space for appended DTB */
|
||||
+ . += 0x100000;
|
||||
+ }
|
||||
+
|
||||
+ _edata_dtb = .;
|
||||
+
|
||||
/*
|
||||
* The image_end section appears after any additional loadable sections
|
||||
* that the linker may decide to insert in the binary image. Having
|
||||
@@ -132,4 +139,4 @@ SECTIONS
|
||||
.stab.indexstr 0 : { *(.stab.indexstr) }
|
||||
.comment 0 : { *(.comment) }
|
||||
}
|
||||
-ASSERT(_edata_real == _edata, "error: zImage file size is incorrect");
|
||||
+ASSERT(_edata_real == _edata_dtb, "error: zImage file size is incorrect");
|
||||
@ -0,0 +1,66 @@
|
||||
From 11d6a6128a5a07c429941afc202b6e62a19771be Mon Sep 17 00:00:00 2001
|
||||
From: John Thomson <git@johnthomson.fastmail.com.au>
|
||||
Date: Fri, 23 Oct 2020 19:42:36 +1000
|
||||
Subject: [PATCH 2/2] arm: compressed: set ipq40xx watchdog to allow boot
|
||||
|
||||
For IPQ40XX systems where the SoC watchdog is activated before linux,
|
||||
the watchdog timer may be too small for linux to finish uncompress,
|
||||
boot, and watchdog management start.
|
||||
If the watchdog is enabled, set the timeout for it to 30 seconds.
|
||||
The functionality and offsets were copied from:
|
||||
drivers/watchdog/qcom-wdt.c qcom_wdt_set_timeout & qcom_wdt_start
|
||||
The watchdog memory address was taken from:
|
||||
arch/arm/boot/dts/qcom-ipq4019.dtsi
|
||||
|
||||
This was required on Mikrotik IPQ40XX consumer hardware using Mikrotik's
|
||||
RouterBoot bootloader.
|
||||
|
||||
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
|
||||
---
|
||||
arch/arm/boot/compressed/head.S | 35 +++++++++++++++++++++++++++++++++
|
||||
1 file changed, 35 insertions(+)
|
||||
|
||||
--- a/arch/arm/boot/compressed/head.S
|
||||
+++ b/arch/arm/boot/compressed/head.S
|
||||
@@ -599,6 +599,41 @@ not_relocated: mov r0, #0
|
||||
bic r4, r4, #1
|
||||
blne cache_on
|
||||
|
||||
+/* Set the Qualcom IPQ40xx watchdog timeout to 30 seconds
|
||||
+ * if it is enabled, so that there is time for kernel
|
||||
+ * to decompress, boot, and take over the watchdog.
|
||||
+ * data and functionality from drivers/watchdog/qcom-wdt.c
|
||||
+ * address from arch/arm/boot/dts/qcom-ipq4019.dtsi
|
||||
+ */
|
||||
+#ifdef CONFIG_ARCH_IPQ40XX
|
||||
+watchdog_set:
|
||||
+ /* offsets:
|
||||
+ * 0x04 reset (=1 resets countdown)
|
||||
+ * 0x08 enable (=0 disables)
|
||||
+ * 0x0c status (=1 when SoC was reset by watchdog)
|
||||
+ * 0x10 bark (=timeout warning in ticks)
|
||||
+ * 0x14 bite (=timeout reset in ticks)
|
||||
+ * clock rate is 1<<15 hertz
|
||||
+ */
|
||||
+ .equ watchdog, 0x0b017000 @Store watchdog base address
|
||||
+ movw r0, #:lower16:watchdog
|
||||
+ movt r0, #:upper16:watchdog
|
||||
+ ldr r1, [r0, #0x08] @Get enabled?
|
||||
+ cmp r1, #1 @If not enabled, do not change
|
||||
+ bne watchdog_finished
|
||||
+ mov r1, #0
|
||||
+ str r1, [r0, #0x08] @Disable the watchdog
|
||||
+ mov r1, #1
|
||||
+ str r1, [r0, #0x04] @Pet the watchdog
|
||||
+ mov r1, #30 @30 seconds timeout
|
||||
+ lsl r1, r1, #15 @converted to ticks
|
||||
+ str r1, [r0, #0x10] @Set the bark timeout
|
||||
+ str r1, [r0, #0x14] @Set the bite timeout
|
||||
+ mov r1, #1
|
||||
+ str r1, [r0, #0x08] @Enable the watchdog
|
||||
+watchdog_finished:
|
||||
+#endif /* CONFIG_ARCH_IPQ40XX */
|
||||
+
|
||||
/*
|
||||
* The C runtime environment should now be setup sufficiently.
|
||||
* Set up some pointers, and start decompressing.
|
||||
@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
|
||||
--- a/arch/arm/boot/dts/Makefile
|
||||
+++ b/arch/arm/boot/dts/Makefile
|
||||
@@ -837,11 +837,58 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
@@ -837,11 +837,68 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
qcom-apq8074-dragonboard.dtb \
|
||||
qcom-apq8084-ifc6540.dtb \
|
||||
qcom-apq8084-mtp.dtb \
|
||||
@ -18,8 +18,10 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
+ qcom-ipq4018-ap120c-ac.dtb \
|
||||
+ qcom-ipq4018-dap-2610.dtb \
|
||||
+ qcom-ipq4018-cs-w3-wd1200g-eup.dtb \
|
||||
+ qcom-ipq4018-magic-2-wifi-next.dtb \
|
||||
+ qcom-ipq4018-ea6350v3.dtb \
|
||||
+ qcom-ipq4018-eap1300.dtb \
|
||||
+ qcom-ipq4018-ecw5211.dtb \
|
||||
+ qcom-ipq4018-emd1.dtb \
|
||||
+ qcom-ipq4018-emr3500.dtb \
|
||||
+ qcom-ipq4018-ens620ext.dtb \
|
||||
@ -27,11 +29,18 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
+ qcom-ipq4018-ex6150v2.dtb \
|
||||
+ qcom-ipq4018-ex6200v2.dtb \
|
||||
+ qcom-ipq4018-fritzbox-4040.dtb \
|
||||
+ qcom-ipq4018-gl-ap1300.dtb \
|
||||
+ qcom-ipq4018-jalapeno.dtb \
|
||||
+ qcom-ipq4018-meshpoint-one.dtb \
|
||||
+ qcom-ipq4018-hap-ac2.dtb \
|
||||
+ qcom-ipq4018-sxtsq-5-ac.dtb \
|
||||
+ qcom-ipq4018-nbg6617.dtb \
|
||||
+ qcom-ipq4019-oap100.dtb \
|
||||
+ qcom-ipq4018-pa1200.dtb \
|
||||
+ qcom-ipq4018-rt-ac58u.dtb \
|
||||
+ qcom-ipq4018-wac510.dtb \
|
||||
+ qcom-ipq4018-wre6606.dtb \
|
||||
+ qcom-ipq4018-wrtq-329acn.dtb \
|
||||
qcom-ipq4019-ap.dk01.1-c1.dtb \
|
||||
qcom-ipq4019-ap.dk04.1-c1.dtb \
|
||||
qcom-ipq4019-ap.dk04.1-c3.dtb \
|
||||
@ -40,7 +49,6 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
+ qcom-ipq4019-a62.dtb \
|
||||
+ qcom-ipq4019-c526a.dtb \
|
||||
+ qcom-ipq4019-c526a-128m.dtb \
|
||||
+ qcom-ipq4019-ca100.dtb \
|
||||
+ qcom-ipq4019-cm520-79f.dtb \
|
||||
+ qcom-ipq4019-ea8300.dtb \
|
||||
+ qcom-ipq4019-eap2200.dtb \
|
||||
@ -48,9 +56,11 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
+ qcom-ipq4019-fritzrepeater-1200.dtb \
|
||||
+ qcom-ipq4019-fritzrepeater-3000.dtb \
|
||||
+ qcom-ipq4019-map-ac2200.dtb \
|
||||
+ qcom-ipq4019-mr8300.dtb \
|
||||
+ qcom-ipq4019-e2600ac-c1.dtb \
|
||||
+ qcom-ipq4019-e2600ac-c2.dtb \
|
||||
+ qcom-ipq4019-habanero-dvk.dtb \
|
||||
+ qcom-ipq4019-pa2200.dtb \
|
||||
+ qcom-ipq4019-r619ac.dtb \
|
||||
+ qcom-ipq4019-rtl30vw.dtb \
|
||||
+ qcom-ipq4019-rt-acrh17.dtb \
|
||||
|
||||
@ -1,9 +0,0 @@
|
||||
define Profile/Default
|
||||
NAME:=Default Profile
|
||||
PRIORITY:=1
|
||||
endef
|
||||
|
||||
define Profile/Default/Description
|
||||
Default package set compatible with most boards.
|
||||
endef
|
||||
$(eval $(call Profile,Default))
|
||||
Loading…
Reference in New Issue
Block a user