The Sophos AP15C uses the same hardware as the AP15, but has a reset button.
Based on:
commit 6f1efb2898 ("ath79: add support for Sophos AP100/AP55 family")
author Andrew Powers-Holmes <andrew@omnom.net>
Fri, 3 Sep 2021 15:53:57 +0200 (23:53 +1000)
committer Hauke Mehrtens <hauke@hauke-m.de>
Sat, 16 Apr 2022 16:59:29 +0200 (16:59 +0200)
Unique to AP15C:
- Reset button
- External RJ45 serial console port
Flashing instructions:
This firmware can be flashed either via a compatible Sophos SG or XG
firewall appliance, which does not require disassembling the device, or via
the U-Boot console available on the internal UART header.
To flash via XG appliance:
- Register on Sophos' website for a no-cost Home Use XG firewall license
- Download and install the XG software on a compatible PC or virtual
machine, complete initial appliance setup, and enable SSH console access
- Connect the target AP device to the XG appliance's LAN interface
- Approve the AP from the XG Web UI and wait until it shows as Active
(this can take 3-5 minutes)
- Connect to the XG appliance over SSH and access the Advanced Console
(Menu option 5, then menu option 3)
- Run `sudo awetool` and select the menu option to connect to an AP via
SSH. When prompted to enable SSH on the target AP, select Yes.
- Wait 2-3 minutes, then select the AP from the awetool menu again. This
will connect you to a root shell on the target AP.
- Copy the firmware to /tmp/openwrt.bin on the target AP via SCP/TFTP/etc
- Run `mtd -r write /tmp/openwrt.bin astaro_image`
- When complete, the access point will reboot to OpenWRT.
To flash via U-Boot serial console:
- Configure a TFTP server on your PC, and set IP address 192.168.99.8 with
netmask 255.255.255.0
- Copy the firmware .bin to the TFTP server and rename to 'uImage_AP15C'
- Open the target AP's enclosure and locate the 4-pin 3.3V UART header [4]
- Connect the AP ethernet to your PC's ethernet port
- Connect a terminal to the UART at 115200 8/N/1 as usual
- Power on the AP and press a key to cancel autoboot when prompted
- Run the following commands at the U-Boot console:
- `tftpboot`
- `cp.b $fileaddr 0x9f070000 $filesize`
- `boot`
- The access point will boot to OpenWRT.
Signed-off-by: David Lutz <kpanic@hirnduenger.de>
Using the arrow keys to navigate the U-Boot menu often leads to being
dropped into the U-Boot shell unexpectedly.
This can be prevented in most cases by improving the logic to detect the
arrow key ESC sequence and only reprinting the menu if actually needed.
Also enable CONFIG_SERIAL_RX_BUFFER for all boards as it helps preventing
the remaining cases.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This commit adds u-boot support for the NanoPi R3S.
Signed-off-by: Kevin Zhang <kevin@kevinzhang.me>
Link: https://github.com/openwrt/openwrt/pull/16738
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Increase rng-seed size to make Linux happy and initialize rng pool instantly.
Linux 5.19+ requires 32 bytes of entropy to initialize random pool, but u-boot
currently provides only 8 bytes.
Boot with 8 byte rng-seed (Linux 6.11):
# dmesg | grep crng
[ 12.089286] random: crng init done
Boot with 32 byte rng-seed (Linux 6.11):
# dmesg | grep crng
[ 0.000000] random: crng init done
Link: https://lore.kernel.org/u-boot/20241016100203.629713-1-alexthreed@gmail.com/
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Update package to the latest stable version and drop upstreamed patches:
0001-arm-mvebu-turris_omnia-Enable-LTO-by-default-on-Turr.patch
100-mvebu-armada-8k-respect-CONFIG_DISTRO_DEFAULTS.patch
Other patches automatically refreshed (line numbers only)
Add custom config flags to disable building efimkcapsule by default.
This introduces a dependency to GnuTLS which is not present and we do
not need it here.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/16676
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for NEC Aterm series devices based on QCA9558.
The following devices have almost the same hardware, so the same U-Boot
binary can be used for them.
- NEC Aterm WG1400HP
- NEC Aterm WG1800HP
- NEC Aterm WG1800HP2
By the way, on NetBSD-based NEC Aterm devices, only 0x20000 (128KiB) is
available for a bootloader on the flash chip and that limitation is too
small for mainline U-Boot with the default options. So many
features/commands not required for booting OpenWrt and recoverying are
disabled on that devices, like the followings.
- networking support
- FIT support
- all decompression methods support
etc...
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16297
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add initial support for Qualcomm Atheros QCA955x series SoCs.
This support was based on the QCA956x support, QSDK, GPL tar of TP-Link
Archer C5 v1.20.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16297
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Building uboot-mediatek fails with GCC-14, uboot v2024.10 and
CONFIG_SYS_NONCACHED_MEMORY defined with error:
cmd/cache.c: In function 'do_dcache':
cmd/cache.c:57:25: error: implicit declaration of function
'noncached_set_region' [-Wimplicit-function-declaration]
This is caused by upstream commit 7d6cee2cd0e2e2507aca1e3a6fe0e2cb241a116e
("cmd: cache: Remove weak functions") as this removes weak functions in
favor of arch-specific definitions.
This patch adds the function prototype for `noncached_set_region` to
arch-specific header for ARM. It also adds an include in cmd/cache.c to
make the function available there.
Fixes: #16697
Fixes: f8c22c9bff ("uboot-mediatek: update to U-Boot 2024.10")
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
[@dangowrt refreshed patch]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The OpenWrt layout will waste about 30 MiB spaces, which is... a lot.
It makes sense to keep this stock layout.
This reverts commit 6a6c7a2395.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
New bootloaders for mainline firmware are available at:
https://drive.wrt.moe/uboot/qualcommax
Flash instructions:
1. Write stock mibib:
mtd write ipq8071-xiaomi-*-mibib-stock.bin /dev/mtd1
2. Write new u-boot:
mtd write ipq8071-xiaomi-*-uboot-stock.bin /dev/mtd7
3. Reboot the device, enter web failsafe by pressing the 'reset' button for 5 seconds.
4. Flash *.initramfs-factory.ubi firmware.
5. After ImmortalWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
This tool will load the uboot environment to /var/run/uboot-env/. This allows
more efficient use when accessing multiple variables.
Signed-off-by: John Crispin <john@phrozen.org>
Platform specified fiptool files was moved before lf-6.6.23-2.0.0 bump.
But PLAT_FIPTOOL_HELPER_MK still pointed to old location.
This cause problems with ls-ddr-phy build.
This patch fix PLAT_FIPTOOL_HELPER_MK path.
Fixes: 0ec659bd2b ("tfa-layerscape: Bump to lf-6.6.23-2.0.0")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16472
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hardware
--------
RockChip RK3588 ARM64 (8 cores)
8GB LPDDR4 RAM
2x 2500 Base-T (PCIe, rtl8125b)
1x LED
128GB eMMC on-board
Micro-SD Slot
HDMI IN/OUT
USB 3.0 Port
USB Type-C 3.0 Port
M.2 B-Key
M.2 E-Key
M.2 M-Key
DC Jack 12V
Installation
------------
Uncompress the ImmortalWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Add support for the ArmSoM Sige7 board.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16462
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add u-boot support based on the kernel dts introduced in d1016446 and
the GL-MT6000 u-boot support in fe10f974.
The pcie-mediatek-gen3 kernel driver doesn't like hotplug, so to work in
PCIe mode, the 5G modem on this device needs to be switched on by u-boot
before starting the kernel. Include an init_modem step in the boot_system
action to set the relevant gpios. (The factory bootloader does the same,
using Mediatek SDK-specific gpio_power_clr and gpio_pull_up.)
Ideally the modem would be started using gpio-hog in the device tree, but
this will need to wait until mediatek gpio-hog support is fixed upstream:
https://lore.kernel.org/u-boot/6ef2583e85eea60560d7776377d662779e7c44e5.1722419839.git.chris@arachsys.com/
The bootloader can be replaced using the built-in web interface of the
factory bootloader. Hold the reset button for five seconds while powering
on the device and it will boot into a recovery http server.
http://192.168.1.1/uboot.html and http://192.168.1.1/bl2.html can then
be used to upload openwrt-mediatek-filogic-glinet_gl-x3000-bl31-uboot.fip
and openwrt-mediatek-filogic-glinet_gl-x3000-preloader.bin respectively.
Alternatively, from a root shell on the running system, unlock the boot
partition with
echo 0 >/sys/block/mmcblk0boot0/force_ro
then write openwrt-mediatek-filogic-glinet_gl-x3000-bl31-uboot.fip to
/dev/mmcblk0p4 and openwrt-mediatek-filogic-glinet_gl-x3000-preloader.bin
to /dev/mmcblk0boot0.
Signed-off-by: Chris Webb <chris@arachsys.com>
Link: https://github.com/openwrt/openwrt/pull/15645
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch add a version to uboot patches to help identify in
futures updates when they were upstreamed.
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
