Using the arrow keys to navigate the U-Boot menu often leads to being
dropped into the U-Boot shell unexpectedly.
This can be prevented in most cases by improving the logic to detect the
arrow key ESC sequence and only reprinting the menu if actually needed.
Also enable CONFIG_SERIAL_RX_BUFFER for all boards as it helps preventing
the remaining cases.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add u-boot support based on the kernel dts introduced in d1016446 and
the GL-MT6000 u-boot support in fe10f974.
The pcie-mediatek-gen3 kernel driver doesn't like hotplug, so to work in
PCIe mode, the 5G modem on this device needs to be switched on by u-boot
before starting the kernel. Include an init_modem step in the boot_system
action to set the relevant gpios. (The factory bootloader does the same,
using Mediatek SDK-specific gpio_power_clr and gpio_pull_up.)
Ideally the modem would be started using gpio-hog in the device tree, but
this will need to wait until mediatek gpio-hog support is fixed upstream:
https://lore.kernel.org/u-boot/6ef2583e85eea60560d7776377d662779e7c44e5.1722419839.git.chris@arachsys.com/
The bootloader can be replaced using the built-in web interface of the
factory bootloader. Hold the reset button for five seconds while powering
on the device and it will boot into a recovery http server.
http://192.168.1.1/uboot.html and http://192.168.1.1/bl2.html can then
be used to upload openwrt-mediatek-filogic-glinet_gl-x3000-bl31-uboot.fip
and openwrt-mediatek-filogic-glinet_gl-x3000-preloader.bin respectively.
Alternatively, from a root shell on the running system, unlock the boot
partition with
echo 0 >/sys/block/mmcblk0boot0/force_ro
then write openwrt-mediatek-filogic-glinet_gl-x3000-bl31-uboot.fip to
/dev/mmcblk0p4 and openwrt-mediatek-filogic-glinet_gl-x3000-preloader.bin
to /dev/mmcblk0boot0.
Signed-off-by: Chris Webb <chris@arachsys.com>
Link: https://github.com/openwrt/openwrt/pull/15645
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Same as TP-Link TL-XDR608x, this router comes with locked vendor
loader. Add U-Boot build for replacement loader for this device.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15930
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain telnet access:
1. Login into web interface, and download the configuration.
2. Decode and uncompress the configuration:
* Enter fakeroot if you are not login as root.
base64 -d e-xxxxxxxxxxxx-cfg.tar.gz | tar -zx
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; /usr/sbin/telnetd; ) &
5. Repack the configuration:
tar -zc etc/ | base64 > e-xxxxxxxxxxxx-cfg.tar.gz
6. Upload new configuration via web interface, now you can connect to
ASR3000 via telnet.
Flash instructions:
1. Connect to ASR3000, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-abt_asr3000-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-abt_asr3000-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/15887
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
1. Rename function _do_env_set() to env_do_env_set().
2. Replace kwbimage hack with UBOOT_CUSTOMIZE_CONFIG:
"--disable TOOLS_KWBIMAGE" and "--disable TOOLS_LIBCRYPTO".
3. Disable CONFIG_CMD_BOOTEFI_BOOTMGR for all supported devices
because the newly added UEFI bootmenu entries doesn't work.
4. Enable CONFIG_VERSION_VARIABLE for the OpenWrt One.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Co-authored-by: Daniel Golle <daniel@makrotopia.org>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, WPS/Mesh
Power: DC 12V 1A
Gain SSH access:
1. Login into web interface, and download the configuration.
2. Download the configration utilities:
https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7981-nokia-ea0326gmp-config-utils.tar.gz
These binaries are extraced from the factory firmware, which are
dynamically linked with aarch64 musl 1.1.24. To use them, you
must run them under the same runtime environment, otherwise the
binaries will not work properly!
3. Upload the configuration and utilities to a suitable environment.
4. Uncompress the utilities, move them to '/bin' and give them executable permisison:
tar -zxf openwrt-mediatek-mt7981-nokia-ea0326gmp-config-utils.tar.gz
mv mkconfig seama /bin
chmod +x /bin/mkconfig
chmod +x /bin/seama
5. Decrypt and uncompress the configuration:
Enter fakeroot if you are not login as root.
mkconfig -a de-enca -m EA0326GMP_3FE79221BAAA -i EA0326GMP_3FE79221BAAA-xxxxxxxx-backup.tar.gz -o backup.tar.gz
tar -zxf backup.tar.gz
6. Edit 'etc/config/dropbear', set 'enable' to '1'.
7. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
8. Repack the configuration:
tar -zcf backup.tar.gz etc/
mkconfig -a enca -m EA0326GMP_3FE79221BAAA -i backup.tar.gz -o EA0326GMP_3FE79221BAAA-xxxxxxxx-backup.tar.gz
9. Upload new configuration via web interface, now you can SSH to EA0326GMP.
A minimum configuration which enabled SSH access is also provided
to simplify the process:
https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7981-nokia-ea0326gmp-enable-ssh.tar.gz
Flash instructions:
1. SSH to EA0326GMP, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-nokia_ea0326gmp-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-nokia_ea0326gmp-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
This adds support for the bpi-r4 variant with internal 2.5G PHY and
additional ethernet port instead of second sfp.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Add support for Xiaomi Redmi AX6S to be used as a second-stage
UBI loader.
The defconfig/env is minimal: Boot fit from UBI. If that failed,
load and boot initramfs image from TFTP.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
It should be "BananaPi BPi-R3 Mini" instead of just "BananaPi BPi-R3".
Fixes: bc25519f98 ("uboot-mediatek: add builds for BananaPi BPi-R3 mini")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The R3 mini comes with two Airoha EN8811H PHYs for 2.5G Ethernet.
The driver added to U-Boot expects the firmware for the PHY to be
stored inside UBI volume en8811h-fw or MMC boot1 hardware partition.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Move fip and factory into UBI static volumes.
Use fitblk instead of partition parser.
!! RUN INSTALLER FIRST !!
Existing users of previous OpenWrt releases or snapshot builds will
have to **re-run the updated installer** before upgrading to firmware
after this commit.
DO NOT flash or run even just the initramfs image unless you have
run the updated installer which moves the content of the 'factory'
partition into a UBI volume.
tl;dr: DON'T USE YET!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Modernize bootloader and flash memory layout of the BPi-R64 similar to
how it has also been done for the BPi-R3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Modernize U-Boot to provide a better reference:
* store fip image in UBI now that TF-A supports that
* switch from uImage.FIT partition parser to new fitblk
virtual firmware block driver (root=/dev/fit0)
* automatically set root device according to boot_mode register
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rebase local patches on top of quarterly timed release, allowing to
drop numerous patches which have been accepted upstream since the
release of U-Boot 2023.07.02.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add basic U-Boot drop-in replacement compatible with the flash layout
of the vendor loader of the Zbtlink WG3526 (16M) MT7621 router board.
The idea here is a to have a reference build of uboot-mediatek also for
a simple MIPS boards more popular than MT7621 RFB.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Flash procedure is described in next commit.
TLDR:
Copy preloader and uboot to /tmp and write them in the mtd.
This will also require new UBI partition and
volumes to boot openwrt.
mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-preloader.bin bl2
mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-bl31-uboot.fip fip
Changelist:
- Added profile for 4k+256 SPI NAND_TYPE
- Added basic Zyxel EX5601-T0 uboot profile
Backported from hitech95 branch:
- Button RESET pin fix
- Button WPS pin fix
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
The OEM U-Boot uses dual boot and signature verification which does not
support by OpenWrt. So add a custom U-Boot build for OpenWrt.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Improve and package builds for various boot media configurations of the
MediaTek MT7981 reference board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The U-Boot build for the MT7988 reference board booting from SD card
wrongly depended on the 'ddr4' variant of the ARM TrustedFirmware-A build
even though the 'comb' variant is used. Fix that dependency.
Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
While the v2 is nearly identical to v1, v3 uses a different PHY and
needs a different build for Ethernet to work in U-Boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Select many potentially useful options for the MT7988 RFB U-Boot builds.
The resulting loader is intended as a development tool and intends to be
generic. It does *not* have a default bootcmd set, but allows to boot
pretty much everything, including EFI executables.
To install this U-Boot build to the eMMC:
opkg install mmc-utils partx-utils
mmc bootpart enable 1 1 /dev/mmcblk0
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=*mediatek_mt7988a-rfb-nand-emmc-preloader.bin of=/dev/mmcblk0boot0
dd if=*mediatek_mt7988a-rfb-nand-emmc-gpt.bin of=/dev/mmcblk0
partx -a /dev/mmcblk0
dd if=*mediatek_mt7988a-rfb-nand-emmc-bl31-uboot.fip of=/dev/mmcblk0p3
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import pending patches adding support for MT7988 and provide builds
for the reference board for all possible boot media.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Release 2023.07 got tagged wrongly and replaced by follow-up release
2023.07.02.
Now using upstream DTS for BPi-R3.
Removed two patches which made it upstream, refreshed the rest.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
