The OpenWrt layout will waste about 30 MiB spaces, which is... a lot.
It makes sense to keep this stock layout.
This reverts commit 6a6c7a2395.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
New bootloaders for mainline firmware are available at:
https://drive.wrt.moe/uboot/qualcommax
Flash instructions:
1. Write stock mibib:
mtd write ipq8071-xiaomi-*-mibib-stock.bin /dev/mtd1
2. Write new u-boot:
mtd write ipq8071-xiaomi-*-uboot-stock.bin /dev/mtd7
3. Reboot the device, enter web failsafe by pressing the 'reset' button for 5 seconds.
4. Flash *.initramfs-factory.ubi firmware.
5. After ImmortalWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Before this commit, sysupgrade saved the settings backup data to
the area following rootfs even though the device has an actual
rootfs_data partition. The backup data was completely ignored on
the following boot, but since rootfs_data was not being cleared
during sysupgrade, the issue was not noticed earlier.
Note that this commit changes the filesystem of rootfs_data from
ext4 to F2FS (if OEM partitioning is used).
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16463
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
* SoC: Qualcomm IPQ8072A (64-bit Quad-core Arm Cortex-A53 @ 2200MHz)
* Memory: 2x ESMT M15T4G16256A-DEBG2G (1 GiB DDR3-1866 13-13-13)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCN5054 (4x4 5 GHz 802.11ax)
* Wi-Fi: QCN5024 (4x4 2.4 GHz 802.11b/g/n/ax)
* Ethernet: QCA8081 (10/100/1000/2.5GBASE-T)
* Flash: Winbond W29N01HZSINF (128 MiB)
* LEDs: 1x Blue Status (GPIO 42 Active High)
* Buttons: 1x Reset (GPIO 50 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to JP1 and bridge pads of R58 and R62.
2. Connect 3V3 TTL port to TX, RX, and GND, which are positions 1, 2,
and 3 respectively. Be sure to crossover TX and RX.
3. Copy RAM firmware image
openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb
to TFTP server root, available at 192.168.10.1.
4. Connect PoE ethernet cable to the RJ45 port and hold Ctrl+B in the
serial console (115200 baud) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# tftpboot 0x44000000 openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Signed-off-by: George Witt <george.witt@nltsproject.org>
Link: https://github.com/openwrt/openwrt/pull/15832
Signed-off-by: Robert Marko <robimarko@gmail.com>
Cambium Networks XE3-4 is a tri-radio Wi-Fi 6/6E 4×4/2×2 AP.
Hardware:
Model: Cambium Networks XE3-4
CPU: IPQ6010/AP-CP01-C3, SoC Version: 1.0 @ 800 MHz
Memory: 1 GiB
Flash: 512 MiB Macronix MX30UF2G18AC + W25Q128FW
Ethernet: 1x 1 GbE (QCA8072)
1x 2.5 GbE (QCA8081)
Buttons: 1x Reset
Serial: TX, RX, GND
Baudrate: 115200
Radios: Qualcomm Atheros IPQ6018 802.11ax - 2x2 - 2GHz
Qualcomm Atheros IPQ6018 802.11ax - 2x2 - 5GHz
Qualcomm Atheros QCN9074 802.11ax - 4x4 - 5GHz or 6GHz
BLE 4.1
Power: 32.0W 802.3bt5 PoE++
25.5W 802.3at with USB, BT disabled
Size: 215mm x 215mm
Ports: 1x USB 2.0
Antenna: 6 GHz: 6.29 dBi, Omni 30 dBm
5 GHz: 6.12 dBi, Omni 31 dBm
2.4 GHz: 4.85 dBi, Omni 29 dBm
LEDs: Multi-color status LEDs
Mounting: Wall, ceiling or T-bar
Installation: Serial connection
1. Open the AP to get access to the board. Connect RX, TX and GND.
2. Power on the AP, and short the CS pin of the SPI flash with
one of the APs GND pins.
3. Transfer the initramfs image with TFTP
(Default server IP is 192.168.0.120)
# tftpboot factory.ubi
4. Flash the rootfs partition
# flash rootfs
5. Reboot the AP
# reset
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15633
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for Asus RT-AX89X BX revision.
WARNING: Only the BX revision boards (So B1, B2 etc) are supported because
AX revision boards use IPQ8074 v1 SoC which is unsupported.
Specifications:
---------------
* CPU: Qualcomm IPQ8074A Quad core Cortex-A53 @ 2.2GHz
* RAM: 1024MB
* Storage: 256MB SLC NAND (Macronix MX30UF2G18AC)
* Ethernet:
* 5x 1G RJ45 ports via QCA8337 switch
* 3x 1G RJ45 ports via internal switch (QCA8075 PHY)
* 1x 10G RJ45 via internal switch (AQR113C PHY)
* 1x 10G SFP+ slot via internal switch
* WLAN:
* 2.4GHz 4x4
* 5GHz 8x8
* 8 external antennas
* USB: 2x USB 3.0 Type-A
* Buttons:
* Power switch
* WPS
* Reset
* Wireless ON/OFF
* LED ON/OFF
LED-s:
* Power
* Wi-Fi
* WAN
* 10G
* SFP+
Power:
* 19.5V via DC jack
Installation instructions:
--------------------------
1. Flash temporary OpenWrt initramfs:
* Flash openwrt-qualcommax-ipq807x-asus_rt-ax89x-initramfs-factory.trx
via the stock firmware.
Administration -> Firmware Upgrade -> Manual Firmware update (Upload)
After flashing the device will reboot with OpenWrt initramfs and it can
be accesed via any of the LAN ports via SSH with the usual OpenWrt
default credentials.
2. Sysupgrade from OpenWrt initramfs:
* Copy openwrt-qualcommax-ipq807x-asus_rt-ax89x-squashfs-sysupgrade.bin to
/tmp/openwrt-qualcommax-ipq807x-asus_rt-ax89x-squashfs-sysupgrade.bin of
the running initramfs image.
* Simply sysupgrade -n /tmp/openwrt-qualcommax-ipq807x-asus_rt-ax89x-squashfs-sysupgrade.bin
After flashing the device will reboot with OpenWrt initramfs and it can
be accesed via any of the LAN ports via SSH with the usual OpenWrt
default credentials.
Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
Exclude additional initramfs image for Netgear RAX120v2 when no
initramfs image are compiled to fix build error.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix RAX120v2 PWM Fan controller wrong definition by using a non-existant
kmod and using the wrong compatible for it enabling an external clock
while actually the device use an internal one.
Link: https://github.com/openwrt/openwrt/pull/15796
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This commit adds support for Netgear Orbi Pro SXR80 and SXS80 (collectively known as SXK80)
Specifications:
---------------
* CPU: Qualcomm IPQ8074A Quad core Cortex-A53
* RAM: 1024MB
* Storage: SPI-NAND 512 MiB (Winbond W29N04GZ)
* Ethernet: 4x 1G RJ45 ports (QCA8075) 1x 2.5G RJ45 LAN/WAN (QCA8081)
* WLAN:
- 2.4 GHz: Qualcomm QCN5024 4x4
- 2x 5 GHz: Qualcomm QCN5054 4x4 (second radio high channels only)
* LEDs:
- Power: (Green and red)
- Front: (Blue, green, red and white)
* Buttons:
- 1x Soft reset
- 1x Sync/WPS
* Power: 12V DC Jack
Installation instructions (Telnet):
-----------------------------------
*Note, this guide assumes SXR80, for SXS80 change the firmware file name as appropriate
1. Put firmware file openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb in root of TFTP server available at 192.168.1.10.
2. Enable telnet by going to http://[ip of device]/debug.htm and clicking on the tickbox 'Enable telnet'
3. Telnet into the device and login using the same username and password as the web interface:
4. Run the following command:
`fw_setenv bootcmd 'env default -a; saveenv; reset'`
5. Reboot the router, once the web interface is available again re-enable telnet via http://[ip of device]/debug.htm and telnet into the device.
6. Run the following command:
`fw_printenv`
It should look similar to the below:
```
baudrate=115200
bootargs=console=ttyMSM0,115200n8
bootcmd=mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot
bootdelay=2
ipaddr=192.168.1.1
netmask=255.255.255.0
serverip=192.168.1.10
soc_version_major=2
soc_version_minor=0
```
**If you see the message:**
`Warning: Bad CRC, using default environment`
**DO NOT CONTINUE, YOU WILL BRICK YOUR DEVICE**
7. Run the following command:
`fw_setenv originalboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot'`
(This should match what's in the bootcmd variable displayed in step 6)
8. Run the following commands:
```
fw_setenv wrttftp 'mii write 0x0 0x0 0x800; sleep 1; nmrp; if tftpboot openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb; then bootm; fi; bootdni; boot_DNI_secureboot'
fw_setenv wrtboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; nand read 0x40000000 0x1980000 0x06d00000; bootm 0x40000000'
fw_setenv bootcmd 'run wrttftp'
```
9. Ensure SXR/S device is attached via ethernet (LAN port) to the same ethernet segment as the TFTP server.
10. Reboot the device, it should reboot into OpenWrt and be available on 192.168.1.1
11. Once OpenWrt has booted, update the bootcmd using the following command:
`fw_setenv bootcmd 'run wrtboot'`
12. Flash the sysupgrade image
13. It should boot into OpenWrt
References to SXK80 GPL source:
https://www.downloads.netgear.com/files/GPL/SXK80-V3.2.0.108_gpl_src.tar.bz2.zip
Signed-off-by: Flole Systems <flole@flole.de>
Signed-off-by: Andrew Smith <gul.code@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/14939
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hardware specification:
========
SoC: Qualcomm IPQ8072A
Flash: 512MB (Fidelix FMND4G08S3J-ID)
RAM: 1GB (2x Kingston DDR3L D2516ECMDXGJD)
Ethernet: 1x 10/100/1000/2500/5000Mbps (Marvell AQR114C)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 6GHz ax 4x4 (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229
WiFi2: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-177
WiFi3: 2.4GHz ax 4x4 (Qualcomm QCN5024 + Skyworks SKY8340-11)
IoT: Bluetooth 5, Zigbee and Thread (NXP K32W041)
LED: 1x RGB status (NXP PCA9633)
USB: 1x USB 3.0
Button: WPS, Reset
Flash instructions:
========
1. Manually upgrade firmware using openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin image.
More details can be found here: https://www.linksys.com/support-article?articleNum=47547
After first boot check actual partition:
- fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and in case of 1:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd21 0 0
- nandwrite -p /dev/mtd21 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd23 0 0
- nandwrite -p /dev/mtd23 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
3. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
4. Back to the OEM firmware:
- mtd -e kernel -n write FW_MX8500_1.0.11.208937_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MX8500_1.0.11.208937_prod.img alt_kernel
5. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
AQR firmware:
========
1. Firmware loading:
To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function.
To do this, you need to modify u-boot env:
With USB recovery:
- fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
and without:
- fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
2. Firmware updating:
Newer firmware (AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld) is available in the latest OEM firmware.
To load this firmware via u-boot, we need to add the MBN header and update 0:ethphyfw partition.
For MBN header we can use script from this repository: https://github.com/testuser7/aqr_mbn_tool
- python aqr_mbn_tool.py AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld
To update partition we need to install kmod-mtd-rw package first:
- insmod mtd-rw.ko i_want_a_brick=1
- mtd -e /dev/mtd26 -n write aqr_fw.mbn /dev/mtd26
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
Define common Linksys MX device for MX4200v1/v2 and MX5300.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
Spectrum SAX1V1K is a AX WIFI router with 3 1G and 1 2.5G ports.
The router is provided to Spectrum customers.
It is OEM of Askey RT5010W
https://forum.openwrt.org/t/spectrum-sax1v1k-askey-rt5010w-openwrt-support/149923
It continues the original work by @MeisterLone to get this device supported.
Specifications:
```
• CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
• RAM: 2048MB of DDR3
• Storage: 1024MB eMMC
• Ethernet: 3x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081)
• WLAN:
• 2.4GHz: Qualcomm QCN5024 4x4 802.11b/g/n/ax 1174 Mbps PHY rate
• 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
• LED: 1 gpio-controlled dual color led (blue/red)
• Buttons: 1x reset
• Power: 12V DC jack
```
Notes:
```
• This commit adds only single partition support, that means
sysupgrade is upgrading the current rootfs partition.
• Installation can be done by serial connection only.
• A poulated serial header is onboard
https://forum.openwrt.org/t/spectrum-sax1v1k-askey-rt5010w-openwrt-support/149923/6
• RX/TX is working, u-boot bootwait is active, secure boot is enabled.
```
Installation Instructions:
**Most part of the installation is performed from an initramfs image.**
Boot initramfs : Using serial connection
1. Boot up the device and wait till it displays "VERIFY_IB: Success. verify IB ok"
2. Once that message appears,
login with username 'root'
password serial number of your router in uppercase.
3. Use vi to paste the 'open.sh' script from @MeisterLone github on your device
https://github.com/MeisterLone/Askey-RT5010W-D187-REV6/blob/master/Patch/open.sh
4. chmod 755 open.sh
5. ./open.sh
6. Set your ip to 192.168.0.1
7. Run a TFTP server and host the initramfs image on the TFTP server and name it "recovery.img"
8. Reboot device. On boot it will try TFTP.
Install OpenWrt from initramfs image:
1. Use SCP (or other way) to transfer OpenWrt factory image
2. Connect to device using SSH (on a LAN port)
3. Flash firmware: sysupgrade
# sysupgrade -n -v /tmp/openwrt_sysupgrade.bin
4. Set U-boot env variable: bootcmd
# fw_setenv bootcmd "run fix_uboot; run setup_and_boot"
5. Reboot the device
# reboot
6. Once device is booted, residue of previous firmware will prevent openwrt to work properly.
Factory Reset is MUST required
# Once serial console is displaying to login, hold reset button for 10 sec
7. Now everything should be operational.
Note: this PR adds only single partition support, that means sysupgrade is
upgrading the current rootfs partition
Signed-off-by: Connor Yoon <j_connor@taliaent.com>
Netgear WAX214 is a 802.11 ax dual-band AP
with PoE. (similar to Engenius EWS357APV3)
Specifications:
• CPU: Qualcomm IPQ6010 Quad core Cortex-A53
• RAM: 512MB of DDR3
• Storage: 128MB NAND (Macronix MX30UF1G18AC)
• Ethernet: 1x 1G RJ45 port (QCA8072) PoE
• WIFI:
2.4GHz: Qualcomm QCN5022 2x2 802.11b/g/n/ax 574 Mbps PHY rate
5GHz: Qualcomm QCN5052 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate
• LEDs:
4 x GPIO-controlled LEDs
- 1 Power LED (orange)
- 1 LAN LED (blue)
- 1 WIFI 5g LED (blue)
- 1 WIFI 2g LED (blue)
black_small_square Buttons: 1x soft reset
black_small_square Power: 12V DC jack or PoE (802.3af )
An populated serial header is onboard, format is
1.25mm 4p (DF13A-4P-1.25H)
RX/TX is working, bootwait is active, secure boot is not
enabled.
The root password of the stock firmware is unknown,
but failsafe mode can be entered to reset the password.
Installation Instructions:
- obtain serial access
- stop auto boot (press "4", Entr boot command line
interface)
- setenv active_fw 0 (to boot from the primary rootfs,
or set to 1 to boot from the secondary rootfs
partition)
- saveenv
- tftpboot the initramfs image
- bootm
- copy
openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi
to the device
- write the image to the NAND:
- cat /proc/mtd and look for rootfs partition (should
be mtd11,
or mtd12 if you choose active_fw 1)
- ubiformat /dev/mtd11 -f -y
openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi
- reboot
Note: the firmware is senao-based. But I was unable to build
a valid senao-header into the image.
Maybe they changed the header format and senaoFW isn't
working any more.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
These recipes are generic and will be used for other subtargets, so lets
move them to the target Makefile so they can reused.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Introduce support for the Qualcomm IPQ60xx SoC. WiFi support still has
to be handled and correctly fix hence this is currently marked as
source-only to have a solid base to progress on correct support of this
and hope Upstream QUIC publish newers ath11k drivers for this SoC.
Co-developed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Mantas Pucka <mantas@8devices.com>
[ improve commit description, add SoB for Robert, make it source-only ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Enable LED driver LP5562 on HAZE device tree and include its kernel
module package on default package for HAZE.
Signed-off-by: CheWei Chien <chewei.chien@wnc.com.tw>
Linksys MX4200 is a 802.11ax Tri-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8174 Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 512Mb NAND
* Ethernet: 4x1G RJ45 ports (QCA8075)
* WLAN:
* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
* 5GHz: Qualcomm QCN5054 2x2@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LED-s:
* RGB system led
* Buttons: 1x Soft reset 1x WPS
* Power: 12V DC Jack
Installation instructions:
Open Linksys Web UI - http://192.168.1.1/ca or http://10.65.1.1/ca depending on your setup.
Login with your admin password. The default password can be found on a sticker under the device.
To enter into the support mode, click on the “CA” link and the bottom of the page.
Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button.
Click start. Ignore all the prompts and warnings by click “yes” in all the popups.
The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device.
Then you would need to write openwrt to the other partition for it to work
- First Check booted partition
fw_printenv -n boot_part
- Then install Openwrt to the other partition if booted in slot 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin alt_kernel
- If in slot 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin kernel
Replace (X) with your model version either 1 or 2
Signed-off-by: Mohammad Sayful Islam <sayf.mohammad01@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Hardware specifications:
SoC: Qualcomm IPQ8071A
RAM: 512MB of DDR3
Flash1: Eon EN25S64 8MB
Flash2: MX30UF2G18AC 256MB
Ethernet: 2x 2.5G RJ45 port
Phone: 1x RJ11 port (SPI)
USB: 1x Type-C 2.0 port
WiFi1: QCN5024 2.4GHz
WiFi2: QCN5054 5GHz
Button: Reset, WPS
Flash instructions:
1. Connect the router via serial port (115200 8N1 1.8V)
2. Download the initramfs image, rename it to initramfs.bin,
and host it with the tftp server.
3. Interrupt U-Boot and run these commands:
tftpboot initramfs.bin
bootm
4. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Hardware specification:
SoC: Qualcomm IPQ8072A
Flash: Toshiba NAND 1GiB
RAM: 1 GiB of DDR3 466 MHz
Ethernet: 4x 1Gbps + 1x 2.5Gbps
WiFi1: QCN5024 2.4GHz ax 4x4
WiFi2: QCN5054 5GHz ax 4x4
Button: WiFi, WPS, Reset
Modem: RG500Q-EA
USB: 1 x USB 3.0
Power: DC 12V 4A
Flash instructions:
1. Download the initramfs image, rename it to
initramfs.bin, and host it with tftp server.
2. Interrupt U-Boot and run these commands:
tftpboot initramfs.bin
bootm
3. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Replace blanks with tabs, also sort base-files alphabetically.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Robert Marko <robimarko@gmail.com>
