Remove upstreamed from 2.11 release:
060-nl80211-fix-crash-when-adding-an-interface-fails.patch
Rebase all other patches
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16338
Signed-off-by: Robert Marko <robimarko@gmail.com>
Release 2.11 has been quite a few new features and fixes since the 2.10
release. The following ChangeLog entries highlight some of the main
changes:
* Wi-Fi Easy Connect
- add support for DPP release 3
- allow Configurator parameters to be provided during config exchange
* HE/IEEE 802.11ax/Wi-Fi 6
- various fixes
* EHT/IEEE 802.11be/Wi-Fi 7
- add preliminary support
* SAE: add support for fetching the password from a RADIUS server
* support OpenSSL 3.0 API changes
* support background radar detection and CAC with some additional
drivers
* support RADIUS ACL/PSK check during 4-way handshake (wpa_psk_radius=3)
* EAP-SIM/AKA: support IMSI privacy
* improve 4-way handshake operations
- use Secure=1 in message 3 during PTK rekeying
...and many more
Remove upstreamed patches:
023-ndisc_snoop-call-dl_list_del-before-freeing-ipv6-add.patch
030-driver_nl80211-rewrite-neigh-code-to-not-depend-on-l.patch
040-mesh-allow-processing-authentication-frames-in-block.patch
181-driver_nl80211-update-drv-ifindex-on-removing-the-fi.patch
182-nl80211-move-nl80211_put_freq_params-call-outside-of.patch
183-hostapd-cancel-channel_list_update_timeout-in-hostap.patch
210-build-de-duplicate-_DIRS-before-calling-mkdir.patch
253-qos_map_set_without_interworking.patch
751-qos_map_ignore_when_unsupported.patch
800-SAE-Check-for-invalid-Rejected-Groups-element-length.patch
801-SAE-Check-for-invalid-Rejected-Groups-element-length.patch
802-SAE-Reject-invalid-Rejected-Groups-element-in-the-pa.patch
Other patches has been updated.
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16338
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
- Device: DNA Valokuitu Plus EX400
- SoC: MT7621A
- Flash: 256MB NAND
- RAM: 256MB
- Ethernet: Built-in, 2 x 1GbE
- Wifi: MT7603 2.4 GHz, MT7615 5 GHz (4x internal antennas)
- USB: 1x 3.0
- LED: 1x green/red, 1x green
- Buttons: Reset
MAC addresses:
- LAN: u-boot 'ethaddr' (label)
- WAN: label + 1
- 2.4 GHz: label + 6
- 5 GHz: label + 7
Serial:
There is a black block connector next to the red ethernet connector. It
is accessible also through holes in the casing.
Pinout (TTL 3.3V)
+---+---+
|Tx |Rx |
+---+---+
|Vcc|Gnd|
+---+---+
Firmware:
The vendor firmware is a fork of OpenWrt (Reboot) with a kernel version
4.4.93. The flash is arranged as below and there is a dual boot
mechanism alternating between rootfs_0 and rootfs_1.
+-------+------+------+-----------+-----------+
| | env1 | env2 | rootfs_0 | rootfs_1 |
| +------+------+-----------+-----------+
| | UBI volumes |
+-------+-------------------------------------+
|U-Boot | UBI |
+-------+-------------------------------------+
|mtd0 | mtd1 |
+-------+-------------------------------------+
| NAND |
+---------------------------------------------+
In OpenWrt rootfs_0 will be used as a boot partition that will contain the
kernel and the dtb. The squashfs rootfs and overlay are standard OpenWrt
behaviour.
+-------+------+------+-----------+--------+------------+
| | env1 | env2 | rootfs_0 | rootfs | rootfs_data|
| +------+------+-----------+--------+------------+
| | UBI volumes |
+-------+-----------------------------------------------+
|U-Boot | UBI |
+-------+-----------------------------------------------+
|mtd0 | mtd1 |
+-------+-----------------------------------------------+
| NAND |
+-------------------------------------------------------+
U-boot:
With proper serial access booting can be halted to U-boot by pressing any
key. TFTP and flash writes are available, but only the first one has been
tested.
NOTE: Recovery mode can be accessed by holding down the reset button while
powering on the device. The led 'Update' will show a solid green light
once ready. A web server will be running at 192.168.1.1:80 and it will
allow flashing a firmware package. You can cycle between rootfs_0 and
rootfs_1 by pressing the reset button once.
Root password:
With the vendor web UI create a backup of your settings and download the
archive to your computer. Within the archive in the file
/etc/shadow replace the password hash for root with that of a password you
know. Restore the configuration with the vendor web UI and you will have
changed the root password.
SSH access:
You might need to enable the SSH service for LAN interface as by default
it's enabled for WAN only.
Installing OpenWrt:
With the vendor web UI install the OpenWrt factory image. Alternatively,
ssh to the device and use sysupgrade -n from cli.
Finalize by installing the OpenWrt sysupgrade image to get a fully
functioning system.
Reverting to the vendor firmware:
Boot with OpenWrt initramfs image
- Remove volumes rootfs_0, rootfs and rootfs_data and create vendor
volumes.
ubirmvol /dev/ubi0 -n 2
ubirmvol /dev/ubi0 -n 3
ubirmvol /dev/ubi0 -n 4
ubimkvol /dev/ubi0 -N rootfs_0 -S 990
ubimkvol /dev/ubi0 -N rootfs_1 -S 990
Power off and enter to the U-boot recovery to install the vendor
firmware.
Known issues:
- MACs for wifi are stored in currently unknown place but it seems
to persist over power-off. They might be stored on the chip.
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
[rmilecki: try NVMEM for MACs]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
- specify CC target explicitly
- define KBUILD_SYM32=n to select "native" build format (if building with 64-bit arch)
- rewrap lines (for good)
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15702
Signed-off-by: Robert Marko <robimarko@gmail.com>
The path for linking libucode.so was not specified for the ucode binary.
This breaks execution of ucode in the host context.
Signed-off-by: David Bauer <david.bauer@uniberg.com>
move nanopc-t6 recipes above rock 5b.
Fixes: 9482341a47 ("rockchip: add support for nanopc t6")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16340
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
* SoC: Qualcomm IPQ8072A (64-bit Quad-core Arm Cortex-A53 @ 2200MHz)
* Memory: 2x ESMT M15T4G16256A-DEBG2G (1 GiB DDR3-1866 13-13-13)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCN5054 (4x4 5 GHz 802.11ax)
* Wi-Fi: QCN5024 (4x4 2.4 GHz 802.11b/g/n/ax)
* Ethernet: QCA8081 (10/100/1000/2.5GBASE-T)
* Flash: Winbond W29N01HZSINF (128 MiB)
* LEDs: 1x Blue Status (GPIO 42 Active High)
* Buttons: 1x Reset (GPIO 50 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to JP1 and bridge pads of R58 and R62.
2. Connect 3V3 TTL port to TX, RX, and GND, which are positions 1, 2,
and 3 respectively. Be sure to crossover TX and RX.
3. Copy RAM firmware image
openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb
to TFTP server root, available at 192.168.10.1.
4. Connect PoE ethernet cable to the RJ45 port and hold Ctrl+B in the
serial console (115200 baud) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# tftpboot 0x44000000 openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Signed-off-by: George Witt <george.witt@nltsproject.org>
Link: https://github.com/openwrt/openwrt/pull/15832
Signed-off-by: Robert Marko <robimarko@gmail.com>
GCC errors on returning int in void function now.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16348
Signed-off-by: Robert Marko <robimarko@gmail.com>
OpenSSL 3.0.15 is a security patch release. The most severe CVE fixed in this release is Moderate.
This release incorporates the following bug fixes and mitigations:
* Fixed possible denial of service in X.509 name checks (CVE-2024-6119)
* Fixed possible buffer overread in SSL_select_next_proto() (CVE-2024-5535)
Added github releases url as source mirror
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16332
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adds u-boot config for access to system env variables on this board
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16312
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
If the user has ip-tiny or ip-full installed there is no need to depend on
BusyBox having any form of `ip` or `ip link` applets.
Signed-off-by: Christian Svensson <blue@cmd.nu>
Link: https://github.com/openwrt/openwrt/pull/16062
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Include hotfix suggested by Sebastian Gottschall to fix bug introduced
with APuP patchset
Signed-off-by: Gioacchino Mazzurco <gio@polymathes.cc>
Link: 0c3001a69e
Link: https://github.com/openwrt/openwrt/pull/16298
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of avoiding returning, propagate error so that the kernel
infrastructure can handle it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16262
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of ignoring errors, let the linux infrastructure handle it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16262
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Besides probing BPF information in running system, bpftool is also used in
generating skeleton, dumping BTF, etc. that is widely used in modern BPF
development. Make it available as a host tool so that we can use it in
package build.
Tested build targeting malta/le on Arch Linux x86_64. bpftools currently
does not support processing cross-endian BPF objects, so big-endian host
is needed to build for big-endian targets using bpftools.
Signed-off-by: Eric Long <i@hack3r.moe>
Link: https://github.com/openwrt/openwrt/pull/16122
Signed-off-by: Robert Marko <robimarko@gmail.com>
480551a3adc4 interface: add support for disabling renew on topology change
b7b294266781 device: add more debugging code
595094f5c213 device: do not pull device present state from hotplug events
4e11e52e9b98 main: add messages to udebug regardless of their log level
091d063f4a9d wireless: handle link updates even if devices are present already
a8e90853c936 interface: improve hotplug handling reliability
cdb41673ceea device: remove redundant newlines from debug messages
cd2a7964f2c0 device: revert to explicit device_set_present calls
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Try to do a clean disconnection via L3 request before the connection is
stopped.
Because this might take up to 6 seconds (the driver does 3 attempts with
a timeout of 2 seconds each), a termination timeout needs to be defined
in the init script.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Move the code for disconnection on exit to a separate function, and also
call it in the code paths for SIGINT and the "quit" CLI command.
While at it, make the patch description a bit clearer.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
