Add support for pstore/ramoops now that DRAM content is preserved
over reboot on MT7622. On each boot, check pstore and boot to recovery
image in case there are records stored in it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
mtd erase needs to be aligned with erase blocks. Use padded image size
for erasing the production volume.
As the environment grew above the current size of 0x1000 bytes by
introducing the new padding function, increase the env size to 0x4000.
While at it, clean up reset button function to work to more reliable on
that board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Erase firmware ereas before writing to recovery or production partition
when updating them via the bootloader menu.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* check image checksums before writing to flash
* only bootmenu_0...9 are working, remove bootmenu_a entry
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Some of bpi-r64 boards have serial NAND attached to SPI bus.
Build U-Boot for booting from SPI-NAND.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
eMMC booloader is stored to separate partition.
FIP size is increased to 2MB.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Add U-Boot build for the Ubiquiti Networks UniFi 6 LR access point.
This allows updating the bootchain to modern ARM Trusted Firmware 2.4
and U-Boot 2021.04 while keeping as much of the existing flash layout
as possible (u-boot-env, factory and eeprom partitions are retained),
gaining robust recovery vs. production dual-boot mechanism.
Add info for the Winbond W25Q512JV SPI NOR flash used in the device
and wait for GPIOs to settle after reset before checking for reset
button.
I2C connected LED controller is not supported yet.
Writing large amounts of data to SPI flash currently doesn't work due
to watchdog timeout causing reset before data write completes.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that sdcard.gz image contains everything needed to boot straight
into production image, no longer force booting into recovery image on
first boot by removing the logic which implemented that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allow selecting either SATA or PCIE functionality using uImage.FIT
configurations and device-tree overlays.
By default, PCIE1 is selected (as it has been before this change).
To select SATA instead, you can do this now:
fw_setenv bootconf config-mt7622-bananapi-bpi-r64-sata
and reboot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Make installation to eMMC more convenient on the BPi-R64 by also
copying the production image (if valid) from SD Card to eMMC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of building all U-Boot variants by default, build only those
needed by the selected board(s).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import patch form Frank Wunderlich <frank-w@public-files.de> to fix
build of MediaTek AHCI SATA driver.
Enable that driver on Bananapi BPi-R64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Copy patch added to uboot-sunxi by commit 3cc57ba462
("uboot-sunxi: add missing type __u64") also to uboot-mediatek.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* make sure USB 2.0 works (useful for UEFI-booting eg. memtest86)
* include more useful U-Boot config options on BPi-R64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MediaTek published their current U-Boot patchset on github:
https://github.com/mtk-openwrt/u-boot/commits/mtksoc
Import the platform patches from there (`00-mtk-*.patch`), arrange,
them nicely, drop no longer needed local patches and rebase on top of
U-Boot 2021.04-rc3.
Tested and works well on Linksys E8450 (snand-1ddr) as well as
Bananapi BPi-R64 (sdmmc-2ddr, emmc-2ddr).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* allow MAC address from U-Boot env to be inhertied
* allow eMMC installation to succeed also without recovery present
on the SD Card.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Change boot menu label for eMMC installation to tell what it does now.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Write everything needed for eMMC install into the gaps between
partitions on SD card. In that way, installation to eMMC only needs
the SD card, no additional files need to be loaded via TFTP any more.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Provide U-Boot variants for SD-card as well as eMMC boot, so we can
generate whole-disk images for the device.
While at it, rename 'mt7622' to 'mt7622-rfb1' to make it less confusing
now that more boards are being added.
Thanks to Frank Wunderlich (@frank-w) for making that nice SVG image
explaining the MMC boot process[1] and for providing the necessary
binary header blobs.
[1]: https://github.com/frank-w/BPI-R64-ATF
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Build U-Boot for the Linksys E8450 in order to have support for UBI.
The loader has a default environment with scripts handling the reset
button as well as fall-back to recovery firmware. If the loader comes
up without a valid environment found in UBI, it will automatically
make sure UBI is formatted and create a new environment and proceed
to load recovery firmware (either from UBI or via TFTP if recovery is
corrupted or unavailable).
If the button is held down during power-on, the yellow status LED
turns on and the bootloader environment is reset to factory defaults.
If the button is released at this point, the recovery firmware (if
existing) is loaded from UBI and booted.
If the button is continously held down even beyond the point that
the yellow LED turned on, the loader will try to load the recovery
firmware via TFTP from server 192.168.1.254, write it to UBI and
boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Now that my patches have been merged into upstream U-Boot, resync the
cosmetic changes and the commit IDs from the final commits.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Ever since this package was introduced, the SDK for mt7629 failed to
build as it started failing on this package.
Fixed by porting Hauke's similar patch for uboot-sunxi to uboot-mediatek.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Instead of building in a default environment which loads our environment
from the FAT partition.... just ask U-Boot to do it.
Submitted upstream at
https://patchwork.ozlabs.org/project/uboot/list/?series=184688
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The U-Boot pinctrl driver for mt7623 was incomplete and didn't handle the
settings required for eMMC to work.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
For building full SD/eMMC images for Banana Pi R2 we'll want a u-boot
image built for that platform.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
