The Sercomm AD1018 has a NAND flash. We recently added support for NANDs
in this target.
Use the internal NAND as additional storage.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The current driver has some troubles:
- Some groupings are wrong.
- The pinctrl group0 owns pins never used (at least in Openwrt) for any
pinmux. The driver hijacks all the pins on the group avoiding any other
use, spite they're free. I.e. for buttons, causing this kernel error:
[ 4.735928] gpio-keys-polled keys: unable to claim gpio 479, err=-22
[ 4.742642] gpio-keys-polled: probe of keys failed with error -22
- Minor errors about groupings on the documentation
- Missing "diag" grouping in dtsi
- Wrong groupings in dtsi
Fix it by setting the correct groups.
And relax the pin capturing, letting the gpios belonging to any group to
be used for other purposes like buttons. This was the behavior with stock
firmwares and old OpenWrt versions which never caused any trouble.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
SPDX moved from GPL-2.0 to GPL-2.0-only and from GPL-2.0+ to
GPL-2.0-or-later. Reflect that in the SPDX license headers.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The router Nucom R5010UN v2 has the partitions defined for a 8MB flash,
but the flash chip is 16MB size. We are wasting half of the flash.
Fix it and use generic names for partitions.
Fixes: 474cde6123 ("brcm63xx: probe SPI flash through DT")
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The ADB P.DG AV4202N device has a wifi chipset connected via PCI. But the
PCI pinmux is missing and without it the wifi won't work properly.
Add the pinctrl_pci to enable the missing PCI pins for this device.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Fix the switch LAN labels for the DGND3700v1/DGND3800B router,
the order is reversed.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
[cut out of bigger patch, adjust commit title/message accordingly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Huawei Echolife HG622 has hardware controlled LAN LEDs.
Add the ephy led pinctrl to let the router show LAN activity on these
LEDs.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The Pirelli A226M-FWB has a wrong linux partition offset, caused
by a copy-paste error. As of result of this, OpenWrt is currently
broken in this unit.
Fix it.
While at it, also use generic node names and fix the addresses
there as well.
Fixes: a27d59bb42 ("brcm63xx: switch to new partition layout
specification")
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
[also fix/update node names, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sercomm H500-s is an xDSL dual band wireless router based on Broadcom
BCM63167 SoC.
Hardware:
SoC: Broadcom BCM63167
CPU: BMIPS4350 V8.0, 400 MHz, 2 cores
Flash: NAND 128 MiB
RAM: DDR3 128 MiB
Ethernet: 4x 10/100/1000 Mbps
Switch: BCM53134S
Wireless: 802.11b/g/n: BCM435f (integrated)
802.11ac: Quantenna QT3740BC (onboard SoC)
USB: 1x 2.0
LEDs/Buttons: 11x / 2x
Flash instruction, web UI:
1. Reset to defaults using the reset button if the admin password is
unknown
2. Login into the web UI as admin.
Address: http://192.168.0.1
User: admin
Password: VF-ESVodafone-H-500-s or l033i-h500s
3. Go to Settings -> Firmware Update, and select the Openwrt factory
firmware
4. Update the firmware.
5. Wait until it finish, the device will reboot with Openwrt installed
on the alternative image partitions keeping the stock firmware in
the former.
Notes:
- The patch also adds support for the lowi version. Only the factory
firmware is different.
- The integrated Wifi in the Broadcom Soc isn't still supported.
- The Quantenna 802.11ac wifi works ok, but needs to be configured with
the Quantenna client application. It can't be configured with Luci
nor any iw command since it's a separated subsystem linked via
ethernet.
- The BCM53134S external switch is managed via MDIO which isn't
supported in this target. Therefore it will behave as a dumb switch.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Allows to keep a backup firmware in case active firmware is corrupted.
Also fix hsspi address warning.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Support Sercomm firmware partition split.
WFI partition must be defined after bootflag partitions in order for the
parser to properly find bootflag1 and bootflag2 partitions.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
While "ok" is recognized in DT parsing, only "okay" is actually
mentioned as valid value. Replace it accordingly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
NAND is used as extra storage on this device.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Until now only HW modded SPI flash version was supported.
BCM6328 with 64M RAM and 128M NAND.
More info: https://openwrt.org/toh/sercomm/ad1018
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
BCM63169 with 128M RAM, 128M NAND and BCM53125 switch.
Switch is connected by HSSPI to CS5.
More info: https://openwrt.org/toh/comtrend/vg8050
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
BCM6362 with 64M RAM, 32M NAND and BCM53125 switch.
Switch is connected by MMAP, which is currently unsupported (no VLANs).
More info: https://openwrt.org/toh/netgear/dgnd3700v2
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
While "ok" is recognized in DT parsing, only "okay" is actually
mentioned as valid value. Replace it accordingly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit removes the target-specific diag.sh script. This way, the
generic one is used for the target, which uses DT-aliases to specify the
LEDs used.
Though generic diag.sh allows to use different LEDs to indicate different
states, this patch just moves the old assignment and does not try to
"improve" the assignment by using additional colors.
However, individual proposals to do so are welcome.
For the few cases where status_led2 was used in old diag.sh, only the
primary LED was migrated.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
