Add support for uimage headers from ALLNET and provide support for the
SG8208M and SG8310PM devices' magic bytes.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
To parse the ELF kernel loader, a small ELF parser is used that can
handle both ELF32 or ELF64 class loaders. The splitter assumes that the
kernel is always located before the rootfs, whether it is embedded in
the loader or not. If the kernel is located after the rootfs on the
firmware partition, then the rootfs splitter will include it in the
dynamically created rootfs_data partition and the kernel will be
corrupted.
The kernel image is preferably embedded inside the ELF loader, so the
end of the loader equals the end of the kernel partition. This is due to
the way mtd_find_rootfs_from searches for the the rootfs:
- if the kernel image is embedded in the loader, the appended rootfs may
follow the loader immediately, within the same erase block.
- if the kernel image is not embedded in the loader, but placed at some
offset behind the loader (OKLI-style loader), the rootfs must be
aligned to an erase-block after the loader and kernel image.
In case section header table is empty, determine the elf loader size by
finding the end of the last segment, as defined by the program header
table.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
This is useful when booting OpenWrt from ramdisks in order to have both
images partitions defined.
Furthermore, instead of always using img2 for the inactive image, let's use
img1 or img2 accordingly.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
When firmware is flashed, cferam.000 extension is renamed to the next number.
When booting, CFE scans the NAND and picks the partition with the highest
cferam extension and ignores the other one.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The only Sercomm WFI user has been migrated to a dedicated firmware parser.
Keep support for no cferam partition based on a boolean DT property.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Sercomm uses 2 bootflag partitions and boots the firmware with the highest
bootflag. Support splitting the firmware partition while keeping support for
unsplitted layout.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Specifications:
* SoC: MT7621AT
* RAM: 128MB
* Flash: 16MB NOR SPI flash
* WiFi: MT7615N (2.4GHz) and MT7615N (5Ghz)
* LAN: 5x1000M
* Firmware layout is Uboot with extra 96 bytes in header
* Base PCB is AP-MTKH7-0002
* LEDs Power Green,Power Orange,Internet Green,Internet Orange
* LEDs "2.4G" Green & "5G" Green connected directly to wifi module
* Buttons Reset,WPS,WIFI
Flash instruction:
Upload image via emergency recovery mode via Windows "not working with Linux"
Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable.
Give it ~30 seconds, to boot the recovery mode GUI
Connect your client computer to LAN1 of the device
Set your client IP address manually to 192.168.0.2 / 255.255.255.0.
Call the recovery page for the device at http://192.168.0.1
Use the provided emergency web GUI to upload and flash a new firmware to the device
MAC addresses:
lan factory 0xe000 *:55 (label)
wan factory 0xe006 *:58
2.4 GHz factory 0x0004 *:56
5.0 GHz factory 0x8004 *:57
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
This fixes the following compile problem with kernel 4.9 on lantiq:
drivers/mtd/mtdsplit/mtdsplit_uimage.c:244:34: error: array type has incomplete element type 'struct of_device_id'
static const struct of_device_id mtdsplit_uimage_of_match_table[] = {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/mtdsplit/mtdsplit_uimage.c:245:4: error: field name not in record or union initializer
{ .compatible = "denx,uimage" },
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
