* ramips: mt7621.dtsi: add missing pinctrl to ethernet node
Add rgmii1_pins (1st GMAC) and mdio_pins to ethernet node
pinctrl to ensure they are set to correct mode
* ramips: kernel: ralink-eth support mt7621
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: some devices use ralink-eth driver
Also re-added mt7621 hwnat support for some devices.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: AmadeusGhost <amadeus@openjmu.xyz>
* ramips/mt7621: re-added hwnat support
Co-authored-by: LGA1150 <dqfext@gmail.com>
Co-authored-by: Chen Minqiang <ptpt52@gmail.com>
The current one only looks for mt76x2e and mt7603e, and
does not work for 2 or more same Wi-Fi chips.
Refactor the script to cover those cases.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
This drops the shebang from all target files for /lib and
/etc/uci-defaults folders, as these are sourced and the shebang
is useless.
While at it, fix the executable flag on a few of these files.
This does not touch ar71xx, as this target is just used for
backporting now and applying cosmetic changes would just complicate
things.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The uci config section network.globals set up in /bin/config_generate
will only be created if /proc/sys/net/ipv6 exists.
Correspondingly, lacking IPv6 support, the command
uci set network.globals.packet_steering=1
will fail with "uci: Invalid argument" as the network.globals config
has not been set up.
Fix that by adding the setup there as well.
Fixes: dfd62e575c ("ramips: enable packet steering by default on mt7621")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Since 01_enable_packet_steering only touches the network config,
limit the uci commit to this as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Commit f761f4052c had bogus case syntax, the uci-defaults script threw
errors as a result and exited non-zero, probably didn't do what was
intended, but tried over and over since the non-zero exit prevents the
script from being deleted.
Fixes: f761f4052c ("ramips: mt7621: harmonize naming scheme for Mikrotik")
Signed-off-by: Russell Senior <russell@personaltelco.net>
[extend commit title, add Fixes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As evidenced here[1] the device MAC address can be stored at a random
offset in the hard_config partition. Rely on sysfs to update the MAC
address correctly.
Adjust config so that WAN is base MAC and LAN is base MAC +1 to better
match label and vendor OS.
[1] https://github.com/openwrt/openwrt/pull/2850#issuecomment-610809021
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
According to a user in OpenWrt forum, on RouterOS the MAC addresses are
ether1(WAN) = MAC
ether2(LAN2) = MAC+1
ether3(LAN3) = MAC+2
etc.
Fix the MAC addresses in OpenWrt.
Ref: https://forum.openwrt.org/t/few-dumb-question-about-mt7530-rb750gr3-dsa/61608
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[remove label_mac in 02_network]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
SFP cage of this device is connected via a AT8031 phy to port 5 of the switch.
This phy act as a RGMII-to-SerDes converter.
Also a I2C clock gate needs to be enabled in order to access the SFP module via I2C bus.
SFP cage also has module detect pin which is connected to I2C gpio expander.
With this patch the kernel/PHYLINK now can detect, readout and use the SFP module/port.
NOTE: SFP cage / AT8033 PHY only support 1000base-X encoding!
This means that some SGMII modules can work and only at forced 1GBit/full-duplex!
Signed-off-by: René van Dorst <opensource@vdorst.com>
Specifications:
* SoC: MT7621AT
* RAM: 128MB
* Flash: 16MB NOR SPI flash
* WiFi: MT7615N (2.4GHz) and MT7615N (5Ghz)
* LAN: 5x1000M
* Firmware layout is Uboot with extra 96 bytes in header
* Base PCB is AP-MTKH7-0002
* LEDs Power Green,Power Orange,Internet Green,Internet Orange
* LEDs "2.4G" Green & "5G" Green connected directly to wifi module
* Buttons Reset,WPS,WIFI
Flash instruction:
Upload image via emergency recovery mode via Windows "not working with Linux"
Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable.
Give it ~30 seconds, to boot the recovery mode GUI
Connect your client computer to LAN1 of the device
Set your client IP address manually to 192.168.0.2 / 255.255.255.0.
Call the recovery page for the device at http://192.168.0.1
Use the provided emergency web GUI to upload and flash a new firmware to the device
MAC addresses:
lan factory 0xe000 *:55 (label)
wan factory 0xe006 *:58
2.4 GHz factory 0x0004 *:56
5.0 GHz factory 0x8004 *:57
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
This commit sync ramips source code from openwrt master.
1. ramips: gsw_mt7621: disable PORT 5 MAC RX/TX flow control by default
2. ramips: allow to set switchdev by board in ramips_set_preinit_iface
3. kernel: fix typos in KernelPackage description
* generic: support mtd-mac-address-ascii
It supports formats of both 001122334455 and 00:11:22:33:44:55
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* ramips: add JDCloud
Co-authored-by: Yousong Zhou <yszhou4tech@gmail.com>
