* ramips: add xiaomi_miwifi-r3 support
Specification:
- CPU: 580 MHz
- Flash size: 128 MiB NAND
- RAM size: 128 MiB DDR2
- Wireless No1: SoC-integrated: MT7620A 2x2 MIMO 802.11b/g/n (2.4 GHz)
- Wireless No2: On-board chip: MT7612E 2x2 MIMO 802.11a/n/ac (5 GHz)
- Switch: MT7620 built-in 10/100 switch w/ vlan support
- USB: 2.0 x1
Flash instructions:
1. access ssh via https://wiki.openwrt.org/toh/xiaomi/mir3
2. in ssh:
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set uart_en=1
nvram commit
mtd write lede-ramips-mt7620-miwifi-r3-squashfs-kernel1.bin kernel1
mtd write lede-ramips-mt7620-miwifi-r3-squashfs-rootfs0.bin rootfs0
reboot
If you want to revert back to stock fw while on LEDE:
insert usb stick (FAT/FAT32) with stock fw renamed to miwifi.bin
fw_setenv flag_last_success 0
power off the device
hold the reset button and power on the device, keep holding the reset button until yellow led starts blinking.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: add mt7620-nand driver for NAND flash
This add the mt7620-nand driver
and enable nand ubifs for subtarget mt7620
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Co-authored-by: Chen Minqiang <ptpt52@gmail.com>
Specification:
- CPU: 580 MHz
- Flash size: 128 MiB NAND
- RAM size: 128 MiB DDR2
- Wireless No1: SoC-integrated: MT7620A 2x2 MIMO 802.11b/g/n (2.4 GHz)
- Wireless No2: On-board chip: MT7612E 2x2 MIMO 802.11a/n/ac (5 GHz)
- Switch: MT7620 built-in 10/100 switch w/ vlan support
- USB: 2.0 x1
Flash instructions:
1. access ssh via https://wiki.openwrt.org/toh/xiaomi/mir3
2. in ssh:
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set uart_en=1
nvram commit
mtd write lede-ramips-mt7620-miwifi-r3-squashfs-kernel1.bin kernel1
mtd write lede-ramips-mt7620-miwifi-r3-squashfs-rootfs0.bin rootfs0
reboot
If you want to revert back to stock fw while on LEDE:
insert usb stick (FAT/FAT32) with stock fw renamed to miwifi.bin
fw_setenv flag_last_success 0
power off the device
hold the reset button and power on the device, keep holding the reset button until yellow led starts blinking.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
kmod-i2c-mux-pca954x will not get into images unless kmod-i2c-mux is added to
DEVICE_PACKAGES as well.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit dffbe668ab)
* ath79: add support for TP-Link TL-WR882N/WR885N/WR886N
This adds support for the various clones of the TL-WR885N recently
supported ("ath79: add support for TP-Link TL-WR885N v1"):
- tplink,tl-wr882n-v1
- tplink,tl-wr882n-v2
- tplink,tl-wr882n-v3
- tplink,tl-wr885n-v1
- tplink,tl-wr885n-v2
- tplink,tl-wr886n-v2
- tplink,tl-wr886n-v3
- tplink,tl-wr886n-v4
- tplink,tl-wr886n-v5
- tplink,tl-wr886n-v6
- tplink,tl-wr886n-v7
These devices are cloned in ar71xx. All models added in this patch are the same hardware CPU
WR885n V2 was tested.
Specifications:
- SOC: Qualcomm Atheros TP9343-AL3A
- CPU: 750MHz
- Flash: 2 MiB (AH1446 25Q16BS1G E5N102)
- RAM: 16 MiB (Zentel A3S28D40JTP-50)
- WLAN: Qualcomm Atheros TP9343 450Mbps
- Ethernet: Atheros AR8228/AR8229 4 port (100M)
添加TP9343芯片的路由器型号支持，TL-WR882N/WR885N/WR886N系列
* ath79: add support for MerCury MW4530R v1
重新添加水星MW4530R路由器支持
* Repair generate mw4530r firmware default is 8M
* Fix mw4530r forgot to add network settings
This bit is used to specify sdxc pinmap for mt76x8. Details available
in patch description.
To properly solve this problem and the other pinctrl hack in mtk-mmc
driver we'll need to write a dedicated pinctrl driver for mt76x8,
with the support for configuring AGPIO_MODE and RGCTL registers as
well as specially handling GPIO reservation/pinctrl setup for ESDMODE.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for TP-Link TL-WR882N/WR885N/WR886N
This adds support for the various clones of the TL-WR885N recently
supported ("ath79: add support for TP-Link TL-WR885N v1"):
- tplink,tl-wr882n-v1
- tplink,tl-wr882n-v2
- tplink,tl-wr882n-v3
- tplink,tl-wr885n-v1
- tplink,tl-wr885n-v2
- tplink,tl-wr886n-v2
- tplink,tl-wr886n-v3
- tplink,tl-wr886n-v4
- tplink,tl-wr886n-v5
- tplink,tl-wr886n-v6
- tplink,tl-wr886n-v7
These devices are cloned in ar71xx. All models added in this patch are the same hardware CPU
WR885n V2 was tested.
Specifications:
- SOC: Qualcomm Atheros TP9343-AL3A
- CPU: 750MHz
- Flash: 2 MiB (AH1446 25Q16BS1G E5N102)
- RAM: 16 MiB (Zentel A3S28D40JTP-50)
- WLAN: Qualcomm Atheros TP9343 450Mbps
- Ethernet: Atheros AR8228/AR8229 4 port (100M)
添加TP9343芯片的路由器型号支持，TL-WR882N/WR885N/WR886N系列
* ath79: add support for MerCury MW4530R v1
重新添加水星MW4530R路由器支持
* Repair generate mw4530r firmware default is 8M
Generate a cpximg that is compatible with the cpximg loader in Compex' u-boot.
The cpximg loader can be started either by holding the reset button during power
up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept an image
appropriate for the board revision that is etched on the board (e.g. 6A04).
The image can be pushed using tftp:
tftp -v -m binary 192.168.1.1 -c put openwrt-ipq40xx-generic-compex_wpj428-squashfs-cpximg-6a04.bin
cpximg files can also be used with the sysupgrade utility in stock images.
(add SSH key in luci for root access)
In mkmylofw_32m, the calculation of the "partition size" has been preferred
to just padding the partition as this will result in less block transfers
during flashing (while the additional complexity is bearable).
Signed-off-by: Leon M. George <leon@georgemail.eu>
Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
