With the switch from the uImage.FIT partition parser to fitblk the
cmdline needs to be adjusted as well. Do this now as it has been
forgotten when the switch was done.
Fixes: 6368ed1ae5 ("mediatek: mt7623: phase out uImage.FIT partition parser")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This has been tested on two of my Unifi 6 LR v2s:
```bash
$ fw_printenv # before
Cannot parse config file '/etc/fw_env.config': No such file or directory
$ cat /etc/fw_env.config
/dev/mtd3 0x0000 0x1000 0x1000 1
$ fw_printenv
arch=arm
baudrate=115200
board=mt7622_evb
board_name=mt7622_evb
bootcmd=bootubnt
bootdelay=3
bootfile=uImage
cpu=armv7
device_model=U6-LR
ethact=mtk_eth
ethaddr=<redacted>
ethcard=AQR112C
ipaddr=<redacted>
is_default=true
loadaddr=0x5007FF28
macaddr=<redacted>
serverip=<redacted>
soc=mt7622
stderr=serial
stdin=serial
stdout=serial
vendor=mediatek
is_ble_stp=true
```
I had to reverse-engineer the working settings above to the UCI script.
Signed-off-by: Joel Low <joel@joelsplace.sg>
Link: https://github.com/openwrt/openwrt/pull/13897
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This adds support for the bpi-r4 variant with internal 2.5G PHY and
additional ethernet port instead of second sfp.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This adds support for the bpi-r4 variant with internal 2.5G PHY and
additional ethernet port instead of second sfp.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Hardware:
=========
SOC: Qualcomm IPQ4019
WiFi 1: QCA4019 IEEE 802.11b/g/n
WiFi 2: QCA4019 IEEE 802.11a/n/ac
WiFi 3: QCA9886 IEEE 802.11a/n/ac
Bluetooth: Qualcomm CSR8510 (A10)
Zigbee: Silicon Labs EM3581 NCP + Skyworks SE2432L
Ethernet: Qualcomm Atheros QCA8072 (2-port)
Flash: Samsung KLM4G1FEPD (4GB eMMC)
RAM (NAND): 512MB
LED Controller: NXP PCA9633 (I2C)
Buttons: Single reset button (GPIO).
Ethernet:
=========
The device has 2 ethernet ports, configured as follows by default:
- left port: WAN
- right port: LAN
Wifi:
=====
The Wifi radios are turned off by default. To configure the router,
you will need to connect your computer to the LAN port of the device.
Bluetooth and Zigbee:
=====================
Configuration included but not tested.
Storage:
========
For compatibility with stock firmware, all of OpenWrt runs in a 136 MiB
eMMC partition (of which there are two copies, see below). You can also
use partition /dev/mmcblk0p19 "syscfg" (3.4 GiB) any way you see fit.
During very limited tests, stock firmware did not mount this partition.
However, backing up its stock content before use is recommended anyway.
Firmware:
=========
The device uses a dual firmware mechanism: it automatically reverts to
the previous firmware after 3 failed boot attempts.
You can switch to the inactive firmware copy by changing the "boot_part"
U-Boot environment variable. You can also do it by turning on the device
for a couple of seconds and then back off, 3 times in a row.
Installation:
=============
OpenWrt's "factory" image can be installed via the stock web UI:
1. Login to the UI. (The default password is printed on the label.)
2. Enter support mode by clicking on the "CA" link at the bottom.
3. Click "Connectivity", "Choose file", "Start", and ignore warnings.
This port is based on work done by flipy (https://github.com/flipy).
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15345
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upgrade the OpenSBI firmware used by RISC-V CPUs to 1.4.
Runtime-tested:
- d1 (Lichee RV)
- sifiveu (SiFive Unleashed)
Updates since last release:
1.4:
Synopsys DesignWare APB GPIO driver
Zicntr and Zihpm support
Console print improvements
Smepmp support
Simple FDT based syscon regmap driver
Syscon based reboot and poweroff driver
Non-contiguous hpm counters
Smcntrpmf support
Full sparse hartid support
IPI improvements
RFENCE improvements
Zkr support
Andes custom PMU support
1.3.1:
ACLINT driver fix for disabled CPUs
SBI PMU fix for out-of-bound access
Designware GPIO driver
1.3:
Allow platform to influence cold boot HART selection
Starfive JH7110 platform support
Split RX and RW firmware regions
Advertise non-retentive suspend for allwinner D1 platform
Byteorder/endianness conversion macros
SBI debug console extension (Experimental)
Configure the PMA regions for RZ/Five platform
SBI system suspend extension (Experimental)
SBI PMU platform firmware events (Experimental)
SBI CPPC extension (Experimental)
Optimized remote TLB flushes
Simple heap for boot time memory allocations
Bring back no-map DT property for reserved memory nodes
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This is needed to boot the BCM6238-based Inteno XG6846.
Currently this is restricted to the XG6846 board.
Reviewed-by: Paul Donald <newtwen+github@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Well, it seems that cryptopp hash was never refreshed since calling
make package/boot/arm-trusted-firmware-mvebu/check FIXUP=1 V=s does not
actually refresh the download calls hashes so refresh it manually.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Since ("download: don't overwrite VERSION variable") trying to download the
required sources for mvebu ATF will fail with:
Makefile:247: *** Download/mox-boot-builder is missing the SOURCE_VERSION field.. Stop.
This also broke the buildbot mvebu/cortex-a53 builds.
So, fix it by switching to SOURCE_VERSION instead.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
uboot-envtools is currently missing config for Edgerouter-X
and its not immediately obvious what settings to manually
apply.
Provide default configuration for envtools on Edgerouter-X.
Signed-off-by: Tim Lunn <tim@feathertop.org>
The Upstream Linux community has discontinued support for the target.
Maintaining support for it downstream would require too much effort.
Moreover, it seems that the supported hardware is no longer deemed worthy
of it.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Spectrum SAX1V1K is a AX WIFI router with 3 1G and 1 2.5G ports.
The router is provided to Spectrum customers.
It is OEM of Askey RT5010W
https://forum.openwrt.org/t/spectrum-sax1v1k-askey-rt5010w-openwrt-support/149923
It continues the original work by @MeisterLone to get this device supported.
Specifications:
```
• CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
• RAM: 2048MB of DDR3
• Storage: 1024MB eMMC
• Ethernet: 3x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081)
• WLAN:
• 2.4GHz: Qualcomm QCN5024 4x4 802.11b/g/n/ax 1174 Mbps PHY rate
• 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
• LED: 1 gpio-controlled dual color led (blue/red)
• Buttons: 1x reset
• Power: 12V DC jack
```
Notes:
```
• This commit adds only single partition support, that means
sysupgrade is upgrading the current rootfs partition.
• Installation can be done by serial connection only.
• A poulated serial header is onboard
https://forum.openwrt.org/t/spectrum-sax1v1k-askey-rt5010w-openwrt-support/149923/6
• RX/TX is working, u-boot bootwait is active, secure boot is enabled.
```
Installation Instructions:
**Most part of the installation is performed from an initramfs image.**
Boot initramfs : Using serial connection
1. Boot up the device and wait till it displays "VERIFY_IB: Success. verify IB ok"
2. Once that message appears,
login with username 'root'
password serial number of your router in uppercase.
3. Use vi to paste the 'open.sh' script from @MeisterLone github on your device
https://github.com/MeisterLone/Askey-RT5010W-D187-REV6/blob/master/Patch/open.sh
4. chmod 755 open.sh
5. ./open.sh
6. Set your ip to 192.168.0.1
7. Run a TFTP server and host the initramfs image on the TFTP server and name it "recovery.img"
8. Reboot device. On boot it will try TFTP.
Install OpenWrt from initramfs image:
1. Use SCP (or other way) to transfer OpenWrt factory image
2. Connect to device using SSH (on a LAN port)
3. Flash firmware: sysupgrade
# sysupgrade -n -v /tmp/openwrt_sysupgrade.bin
4. Set U-boot env variable: bootcmd
# fw_setenv bootcmd "run fix_uboot; run setup_and_boot"
5. Reboot the device
# reboot
6. Once device is booted, residue of previous firmware will prevent openwrt to work properly.
Factory Reset is MUST required
# Once serial console is displaying to login, hold reset button for 10 sec
7. Now everything should be operational.
Note: this PR adds only single partition support, that means sysupgrade is
upgrading the current rootfs partition
Signed-off-by: Connor Yoon <j_connor@taliaent.com>
Lets update to 2024.04 in order to drop all of the patches as they have
been merged upstream.
Tested on Methode eDPU.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
As commit 3ce1e4c3d3 ("d1: define subtarget specifically") added the
'generic' subtarget, without 'BUILD_SUBTARGET' the correspond U-Boot
package will be no longer selected automatically.
Fixes: 3ce1e4c3d3 ("d1: define subtarget specifically")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
As commit 3ce1e4c3d3 ("d1: define subtarget specifically") added the
'generic' subtarget, without 'BUILD_SUBTARGET' the correspond U-Boot
package will be no longer selected automatically.
Fixes: 3ce1e4c3d3 ("d1: define subtarget specifically")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
HW specifications:
* Mediatek MT7981A
* 256MB SPI-NAND
* 512MB DRAM
* Uplink: 1 x 10/100/1000Base-T Ethernet, Auto MDIX, RJ-45 with 802.3at
PoE (Built-in GBe PHY)
* LAN: 1 x 10/100/1000Base-T Ethernet, Auto MDIX, RJ-45 (Airoha EN8801SC)
* 1 Tricolor LED
* Reset button
* 12V/2.0A DC input
Installation:
Board comes with OpenWifi/TIP which is OpenWrt based, so sysupgrade can
be used directly over SSH.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
The RAM frequency was decreased to 2400MHz for stability in v1.16.
Fixes: ee3c5fdbf2 ("arm-trusted-firmware-rockchip: bump to latest git HEAD")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
So, when updating the hash for at91bootstrap it was done via CHECK_ALL=1
so that updated the PKG_MIRROR_HASH for the main v4 version hash, but
at91bootstrap checkout version depends on the subtarget as well.
Choosing to build for sam9x will change the at91bootstrap version to v3
and this hash was not refreshed thus causing the CI to fail.
Fixes: 6918c637b7 ("treewide: package: update missed hashes after switch to ZSTD")
Signed-off-by: Robert Marko <robimarko@gmail.com>
With the switch to ZSTD for git clone packaging, hashes have changed so
fixup remaining package hashes that were missed in the inital update.
Fixes: b3c1c57 ("treewide: update PKG_MIRROR_HASH to zst")
Signed-off-by: Robert Marko <robimarko@gmail.com>
With the default BUILD_BOT configuration on a linux 6.6 kernel,
the WNDR4700's kernel no longer fits into the alloted ~3.5MiB,
even with LZMA compression.
Bigger kernels are possible, but there's a problem with Netgear's
"bootcmd":
> if loadn_dniimg 0 0x180000 0x4e0000 && chk_dniimg 0x4e0000; then nand read 0x800000 0x180000 0x20000;bootm 0x500000 - 0x800040;else fw_recovery; fi"
This loads the dni-image starting offset 0x180000 from the NAND
flash (which is the DTB partition) to 0x4e0000 in the RAM. It then
checks whenever the provided image is "valid". If it is then it
reads the DTB again to 0x800000 in the RAM and starts the extraction
and boot process. (If the image wasn't valid then it starts the
automated firmware recovery).
The issues here are that first: the kernel image gets "squeezed"
between 0x500040 and 0x7fffff... And second, the decompressor
only has area 0x0 - 0x500000 for decompression.
Hence the image now requires to update the bootcmd by providing
new values (which have been successfully tested with the original
Netgear WNDR4700 v1.0.0.56 firmware) for the RAM locations and
make full use of the fact that loadn_dniimg loads the DTB as well.
This needs to be done only once. Just connect a serial adapter to
interface with uboot and overwrite (and save) the new bootcmd.
WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
Steps:
0. Power-off the WNDR4700
1. Connect the serial interface (you need to open the WNDR4700)
2. Power-up the WNDR4700
3. Monitor the boot-sequence and hit "Enter"-key when it says:
"Hit any key to stop autoboot" (Be quick, you have a ~2 second window)
4. in the Prompt enter the following commands (copy & paste)
setenv bootcmd "if loadn_dniimg 0 0x180000 0xce0000 && chk_dniimg 0xce0000; then bootm 0xd00000 - 0xce0040;else fw_recovery; fi"
saveenv
run bootcmd
Note: This new bootcmd will also unbrick devices that were bricked
by the bigger 4.19-6.1 kernels.
Note2: This method was tested with a WNDR4700. A big kernel with most
debug features enabled on v6.6.22 measured 4.30 MiB when compressed
with lzma. The uncompressed kernel is 12.34 MiB. This is over the 3 MiB,
the device reserves for the kernel... But it booted! For bigger kernels,
the device needs repartitioning of the the ubi partition due to the
kernel+dtb not fitting into the partition.
Note3: For initramfs development. I would advice to load the initramfs
images to 0x800000 (or higher). i.e.: tftp 800000 wndr4700.bin
Note4: the fw_recovery uboot command to transfer the factory image to
the flash still works.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
