Add u-boot support based on the kernel dts introduced in d1016446 and
the GL-MT6000 u-boot support in fe10f974.
The pcie-mediatek-gen3 kernel driver doesn't like hotplug, so to work in
PCIe mode, the 5G modem on this device needs to be switched on by u-boot
before starting the kernel. Include an init_modem step in the boot_system
action to set the relevant gpios. (The factory bootloader does the same,
using Mediatek SDK-specific gpio_power_clr and gpio_pull_up.)
Ideally the modem would be started using gpio-hog in the device tree, but
this will need to wait until mediatek gpio-hog support is fixed upstream:
https://lore.kernel.org/u-boot/6ef2583e85eea60560d7776377d662779e7c44e5.1722419839.git.chris@arachsys.com/
The bootloader can be replaced using the built-in web interface of the
factory bootloader. Hold the reset button for five seconds while powering
on the device and it will boot into a recovery http server.
http://192.168.1.1/uboot.html and http://192.168.1.1/bl2.html can then
be used to upload openwrt-mediatek-filogic-glinet_gl-x3000-bl31-uboot.fip
and openwrt-mediatek-filogic-glinet_gl-x3000-preloader.bin respectively.
Alternatively, from a root shell on the running system, unlock the boot
partition with
echo 0 >/sys/block/mmcblk0boot0/force_ro
then write openwrt-mediatek-filogic-glinet_gl-x3000-bl31-uboot.fip to
/dev/mmcblk0p4 and openwrt-mediatek-filogic-glinet_gl-x3000-preloader.bin
to /dev/mmcblk0boot0.
Signed-off-by: Chris Webb <chris@arachsys.com>
Link: https://github.com/openwrt/openwrt/pull/15645
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification is similar to other devices of the MT Stuart series:
* Mediatek MT7988D (3x Cortex-A73, up to 1.8 GHz clock speed)
* 8 GiB eMMC
* 2 GiB DDR4 RAM
* 2500M/1000M/100M LAN port
* 10000M/5000M/2500M/1000M/100M/10M WAN port
* MT7992 Tri-band (2.4G, 5G, 6G) 2T2R+3T3R+3T3R 802.11be Wi-Fi
* Renesas DA14531MOD Bluetooth
* 2 buttons (Reset, Mesh/WPS)
* uC-controlled RGB LED via I2C
* 2x LED for the 2.5G port, 3x LED for the 10G port
* 3.3V-level 115200 baud UART console via 4-pin Dupont connector
exposed at the bottom of the device
* USB-C PD power input
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of reading it from flash directly, let U-Boot assign the LAN
MAC address. Set label-mac-device while at it and sort aliases in DT
alphabetically.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix a typo in the MAC address assignment script affecting SDG-8734.
Fixes: c71b68acdd ("mediatek: filogic: add Adtran SmartRG Mount Stuart series")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Apply changes suggested by SkyLake Huang for pending series improving
MediaTek Ethernet PHY drivers.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
configure 2.5G PHY LEDs to:
2500/1000: green with blink on TX/RX
100/10: green+yellow with blink on TX/RX
which is similar to other 1G PHY LEDs, which are:
1000: green with blink on TX/RX
100/10: green+yellow with blink on TX/RX
Fixes: 6cc14bf66a ("filogic: support Telenor branded ZyXEL EX5700")
Signed-off-by: Yan Cangang <nalanzeyu@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16082
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
MediaTek SDK uses eth2 as additional LAN port and eth1 as WAN.
Do the same also in OpenWrt to keep settings aligned with the SDK.
Suggested-by: Bc-bocun Chen <bc-bocun.chen@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All boards using the deprecated uImage.FIT partition parser have
been migrated to the new fitblk driver. Drop the now no longer
needed partition parser.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The company Zyxel rebranded some years ago.
Currently the casing is according to the old branding even
for newer devices which already use the new branding.
This commit aligns the casing of Zyxel everywhere.
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15652
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The commit backporting new MTK patches did not update the
Kernel config for mediatek/mt7622 causing the build to
fail.
Simply use the new config symbol name for the driver to
fix the issue.
Fixes: 1069514978 ("mediatek: backport pending Ethernet PHY driver patches")
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/16225
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use pending patchset for 2.5GE PHY driver, unifying LED handling
accross all MediaTek Ethernet PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
