Pick commits adding drivers for audio engine found in MT7986 from
Linux 6.6 as well as follow-up fixes from Linux 6.7.
Signed-off-by: Maso Huang <maso.huang@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Bonanza Peak series are a couple of MT7986-powered 2.5 GBit/s
Wi-Fi 6 residential gateway, access point and mesh router products.
All of them come with an eMMC to boot from, are powered via USB-C and
got a USB 3.0 type-A port. All of them got a Dialog (Renesas) DA14531
Bluetooth module connected via UART. If the device was previously
running stock firmware, the BT chip's internal flash has been loaded
with firmware and it can be attached using hciattach when using
OpenWrt.
SOC: MediaTek MT7986A
RAM: 2 GiB DDR4
eMMC: 8 GiB
Bluetooth: BLE5 (DA14531)
Serial: 3.3V level, 115200 8n1 on 4-pin connector
* SDG-8612 - Dual-band RJ-45 gateway
2x 2.5G MaxLinear PHY for WAN port
3x 1GE LAN ports via MT7531 switch
* SDG-8614 - Dual-band SFP gateway
1x SFP cage with up to 2.5G speed
1x 2.5G MaxLinear PHY for LAN port
3x 1GE LAN ports via MT7531 switch
* SDG-8622 - Tri-band mesh router
2x 2.5G MaxLinear PHY
The MT7986 2G and 5G are used as 2G and 5G high band.
There’s a MT7915 PCIe card for 5G low band.
* SDG-8632 - Tri-band mesh router with 6 GHz
2x 2.5G MaxLinear PHY
The MT7986 serves the 2G and 6G bands.
There’s a MT7915 PCIe card for 5G.
Installation via U-Boot serial console:
0. setup TFTP server with IP 192.168.1.10/24, place initramfs image
renamed to openwrt.XXX where XXX is the internal product number:
SDG-8612: XXX = 412
SDG-8614: XXX = 414
SDG-8622: XXX = 422
SDG-8632: XXX = 432
1. connect to the serial console and power on the device.
Interrupt the bootloader by pressing 'st'
2. setenv boot_mode openwrt ; saveenv
3. run boot1
Load firmware via TFTP and write to flash
4. run boot2
Now OpenWrt initramfs should boot
5. upload sysupgrade.bin via scp to /tmp
6. sysupgrade
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import driver for I2C-connected HolTek MCU controlling the RGBW LED
found in Adtran SmartRG devices.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add downstream DT property to setup the PHY LEDs of the MaxLinear
GPY211 PHY in such way that the VDD of the LED is driven by the SoC
pin rather than the GND (which is the default).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acelink EW-7886CAX is an MT7986A (AKA Filogic 830) based access point.
It has 512 MiB of RAM, one 2.5 Gbps PoE (802.3at) Ethernet port and
on-SoC Wi-Fi. There is no printed MAC label (on my unit).
My unit came with Mediatek's firmware (based on OpenWrt 21.02)
installed. It was possible to simply upgrade using OpenWrt's sysupgrade
tool.
Another verified upgrade method is using U-Boot (requires UART). During
every boot there is "U-Boot Boot Menu". Selecting option "2. Upgrade
firmware" allows using U-Boot's tftp client to load and flash factory
image.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This device does not have wireless hardware, thus we don't need to ship
neither hostapd nor wireless drivers.
Signed-off-by: David Bauer <mail@david-bauer.net>
Append metadata in the special GL.iNet format.
This also enables use of the web-based U-Boot recovery.
U-Boot-Recovery
===============
The GL-MT2500 provides web-based U-Boot recovery. For this, hold the
reset button pressed for 5 seconds when attaching power to the device.
The LED will blink 5 times. Release the reset button.
The OpenWrt sysupgrade image can be installed by navigating to
http://192.168.1.1 in a web-browser.
The device does not work as a DHCP server, so manual IP configuration is
required.
Signed-off-by: David Bauer <mail@david-bauer.net>
Change permissions of the bootcount init script from old mode 100644
to new mode 100755 to ensure its executability.
Fixes: 6cc14bf66a ("filogic: support Telenor branded ZyXEL EX5700")
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Confiabits MT7981 is a Wi-Fi 6 router based on MediaTek MT7981.
Specification:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 128 MiB SPI NAND
- RAM: 256 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- Ethernet: 4x 10/100/1000 Mbps MT7531AE (3xLAN, 1xWAN)
- USB 2.0 port
- Buttons: 1 Reset button, 1 Mesh button.
- LEDs: 7x light-blue, 2x warm-white
- Serial console: internal 4-pin header, 115200 8n1
- Power: 12 VDC, 1.5 A
MAC addresses in stock firmware and in this commit:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 00:0c:43:xx:xx:e1 | label+1 |
| LAN | 00:0c:43:xx:xx:e0 | label |
| WLAN 2g | 00:0c:43:xx:xx:e0 | label |
| WLAN 5g | 02:0c:43:xx:xx:e0 | |
+---------+-------------------+-----------+
The label MAC was found in 'Factory', 0x4
Installation:
The stock firmware is OpenWrt-based. If you can reach LuCI or SSH, just use the sysupgrade image
with the 'Keep settings' option turned off.
Signed-off-by: Luis Mita <luis@luismita.com>
Include XHCI USB drivers on the ZBT-Z8102AX router, the drivers are
required to be able to use the USB-connected M.2 slots for 4G/5G modems.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware
--------
SoC: MediaTek MT7981BA
RAM: 1GB DDR4 (NANYA NT5AD512M16C4-JR)
MMC: 8GB eMMC (Samsung 8GTF4R)
ETH: 1000Base-T LAN (ePHY)
2500Base-T WAN (MaxLinear GPY211C)
BTN: 1x Reset Button
LED: System (blue/white)
VPN (white)
USB: 1x USB-A (USB 3.0)
UART: 115200 8N1 - Pinout on board next to LAN port
Don't connect 3.3V!
Known Issues
------------
U-Boot vendor recovery does not seem to accept any images, neither
GL.iNet images nor OpenWrt images. Recovery requires serial access!
Installation
------------
Upload the OpenWrt sysupgrade image to the Gl.iNet Web-UI. Make sure to
not retain existing settings.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add the make function 'exp_units' for helping evaluate k/m/g size units in
expressions, and use this to consistently replace many ad hoc substitutions
like '$(subst k,* 1024,$(subst m, * 1024k,$(IMAGE_SIZE)))' in makefiles.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Same as commit 3674689, correct 'buswidth' to 'bus-width'.
Also move the nmbm properties outside the partition definition.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
The PGIO configuration should be added for the ZBT-Z8102AX and not the ZBT-Z8103AX
Fixes: c8c2f52262 ("mediatek: add support for Zbtlink ZBT-Z8102AX")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The flash procedure is similar to the Xiaomi AX6000 router.
Load openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb from original Zyxel U-Boot:
tftpboot openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb
bootm 0x46000000
Load mtd-rw
insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1
Format ubi and create ubootenv partitions
ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
Copy openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb to /tmp and create recovery partition.
If your recovery image is larger than 10MiB, size the recovery partition accordingly to make it fit.
ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb
Copy preloader and uboot to /tmp and write them in the mtd
mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-preloader.bin bl2
mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-bl31-uboot.fip fip
Now write the firmware:
sysupgrade -n /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-squashfs-sysupgrade.itb
To create a correct BL2, I had to add a profile for 'spim:4k+256' as I could not find a way to value the variable 'NAND_TYPE'.
Features and fixes from hitech95 tree has been squashed, I'm attaching his commit message:
The Power LED was not working correctly and not reacting
to the boot process and statuses.
The board has space (footprint) for an unpopulated Zigbee chip,
while we dont know the device model having this chip populated
we have to assure that the common dts doesnt enable
interfaces that share pins with such device.
In this instance the PCIe and the uart1 and uart2 are disabled.
Some of the control PCIE pins seems to be used for the Zigbee chip,
UART1 seems to be used as a flash port while UART2 should be the
main comunication interface of Zigbee chip.
The Zigbee chip should be a EFR32MG21. But the pins used for UART
seems to be not on standard PINS used by other adapters.
So it cannot run firmwares shared on the web.
But it should be possible to build a custom firmware with
the corrtect pinmux.
This commit also contains the following squashed commit from hitech95
- mediatek: fix sysupgrade for Zyxel EX7601-T0 ubootmod
Changes and fixes added in common board:
- added aliases for boot status leds.
- added aliases for the mac-label-device.
- added pin claims for core features (MDIO and UART 0)
- added default LEDs configuration (01_leds)
- added default network configuration (02_network)
- added missing kmod-usb3 module for USB3
- fixed LED names
- fixed reset pin for SLIC chip
- removed unused pinmux configurations and devices
- fix LAN (switch) port numbering
- using nvmem cells for wifi eeprom, dropping deprecated "mediatek,mtd-eeprom"
- proper factory partition and mac address handling
- cleaned up spi_nand sections and partition
Changes and fixxes added in stock layout:
- added NMBM, if u-boot has it, the kernel must be informed.
Co-authored-by: Nicolò Veronese <nicveronese@gmail.com>
Co-developed-by: Nicolò Veronese <nicveronese@gmail.com>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Remove bogus 'phy-handle = <&phy0>;', an undefined reference.
Fixes: c8c2f52262 ("mediatek: add support for Zbtlink ZBT-Z8102AX")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Specifications:
SoC: MediaTek MT7981B
RAM: 1024MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 4 LAN (Gigabit)
USB: two M.2 slots for 5G modems via USB 3.0 hub, external USB 3.0 port
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND
Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware
B. Through TFTP
Standard installation via UART:
1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.
Based on patch adding support for similar Zbtlink ZBT-Z8103AX device by
Ian Ishmael C. Oderon.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Quite a few `fiilogic` devices use the `mt7531` switch.
Some of them have a DT node that looks like:
```
switch: switch@0 {
compatible = "mediatek,mt7531";
reg = <31>;
...
};
```
This commit changes the DT node name to `switch@1f`.
Signed-off-by: Rani Hod <rani.hod@gmail.com>
