e303ba8 uqmi: update code generator
7880de8 uqmi: sync data from libqmi project
d647f8d uqmi: add more diagnostics commands
6f95626 uim: add --uim-get-sim-state
Use newly introduce --uim-get-sim-state command to query PIN status
from modems which require using uim instead of dms command for that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
With some debug in qmi.sh using following patch, some errors are visible
in the registration step
@@ -29,6 +29,7 @@ proto_qmi_init_config() {
}
proto_qmi_setup() {
+ set -x
local interface="$1"
local dataformat connstat plmn_mode mcc mnc
local device apn auth username password pincode delay modes pdptype
@@ -224,6 +225,8 @@ proto_qmi_setup() {
fi
done
+ registration=$(uqmi -s -d "$device" --get-serving-system)
+
[ -n "$modes" ] && uqmi -s -d "$device" --set-network-modes "$modes" > /dev/null 2>&1
echo "Starting network $interface"
During the boot of the system, modem could not start automatically its
network registration.
netifd: wan (9235): + echo 'Waiting for network registration'
netifd: wan (9235): Waiting for network registration
netifd: wan (9235): + local 'registration_timeout=0'
netifd: wan (9235): + uqmi -s -d /dev/cdc-wdm1 --get-serving-system
netifd: wan (9235): + grep '"searching"'
netifd: wan (9235): + uqmi -s -d /dev/cdc-wdm1 --get-serving-system
netifd: wan (9235): + registration='{"registration":"not_registered","plmn_mcc":208,"plmn_mnc":20,"plmn_description":"","roaming":true}'
netifd: wan (9235): + '[' -n ]
netifd: wan (9235): + echo 'Starting network wan'
As the while loop checks only "searching" pattern, uqmi.sh script quits
searching loop and continues whereas the modem is not registered
Other issue, after X seconds modem stops searching.
netifd: wan (9213): + uqmi -s -d /dev/cdc-wdm0 --get-serving-system
netifd: wan (9213): + grep '"searching"'
netifd: wan (9213): + '[' -e /dev/cdc-wdm0 ]
netifd: wan (9213): + '[' 3 -lt 0 -o 0 '=' 0 ]
netifd: wan (9213): + let registration_timeout++
netifd: wan (9213): + sleep 1
netifd: wan (9213): + uqmi -s -d /dev/cdc-wdm0 --get-serving-system
netifd: wan (9213): + grep '"searching"'
netifd: wan (9213): + uqmi -s -d /dev/cdc-wdm0 --get-serving-system
netifd: wan (9213): + registration='{"registration":"not_registered"}'
netifd: wan (9213): + '[' -n ]
netifd: wan (9213): + echo 'Starting network wan'
netifd: wan (9213): Starting network wan
If registration_timeout is not expired, registration can be restarted
Signed-off-by: Thomas Richard <thomas.richard@kontron.com>
Tested-by: Florian Eckert <fe@dev.tdt.de>
There already was an option for autoconfiguring IPv4 from QMI but this
was removed by commit 3b9b963e6e ("uqmi: always use DHCP for IPv4").
DHCP does not work on MR400 LTE module (in TL-MR6400 v4) so let's readd
support for IPv4 autoconf from QMI but this time allow to configure this
for IPv4 and IPv6 independently and keep DHCP default on IPv4.
Signed-off-by: Filip Moc <lede@moc6.cz>
Give possibility to wait forever the registration by setting timeout
option to 0.
No timeout can be useful if the interface starts whereas no network is
available, because at the end of timeout the interface will be stopped
and never restarted.
Signed-off-by: Thomas Richard <thomas.richard@kontron.com>
