Before this commit, it was assumed that mkhash is in the PATH. While
this was fine for the normal build workflow, this led to some issues if
make TOPDIR="$(pwd)" -C "$pkgdir" compile
was called manually. In most of the cases, I just saw warnings like this:
make: Entering directory '/home/.../package/gluon-status-page'
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
[...]
While these were only warnings and the package still compiled sucessfully,
I also observed that some package even fail to build because of this.
After applying this commit, the variable $(MKHASH) is introduced. This
variable points to $(STAGING_DIR_HOST)/bin/mkhash, which is always the
correct path.
Signed-off-by: Leonardo Mörlein <me@irrelefant.net>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware Highlights:
- SoC: Qualcomm Atheros AR9531 (650MHz)
- RAM: 128 MB
- Flash: 16 MB SPI NOR
- Ethernet: 10/100: 1x WAN, 4x LAN
- Wireless: QCA9531 2.4GHz (bgn)
- Button: 1x reset button
- LED: SYS, WAN, Wireless, LAN 1~4
Installation:
Configure PC with static IP 192.168.1.x, connect PC with one of RJ45
ports, press the reset button and power up device. Open 192.168.1.1
address in your browser and upload sysupgrade image.
Signed-off-by: AmadeusGhost <amadeus@jmu.edu.cn>
IMAGE_SIZE is widely used in many targets. Declare it in the default template to
clean up redundant code. This also prevents deriving IMAGE_SIZE unintentionally
from the previously defined device.
While at it, remove duplicate KERNEL_SIZE declaration.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The -O option for the tplink-v1-header was missing for the TP-Link
TL-WR902AC v1, while safeloader and MTDPARTS where set up with a
single firmware partition.
This led to bootloops after using sysupgrade.
Fixes: FS#3118
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link TL-WR882N/WR885N/WR886N
This adds support for the various clones of the TL-WR885N recently
supported ("ath79: add support for TP-Link TL-WR885N v1"):
- tplink,tl-wr882n-v1
- tplink,tl-wr882n-v2
- tplink,tl-wr882n-v3
- tplink,tl-wr885n-v1
- tplink,tl-wr885n-v2
- tplink,tl-wr886n-v2
- tplink,tl-wr886n-v3
- tplink,tl-wr886n-v4
- tplink,tl-wr886n-v5
- tplink,tl-wr886n-v6
- tplink,tl-wr886n-v7
These devices are cloned in ar71xx. All models added in this patch are the same hardware CPU
WR885n V2 was tested.
Specifications:
- SOC: Qualcomm Atheros TP9343-AL3A
- CPU: 750MHz
- Flash: 2 MiB (AH1446 25Q16BS1G E5N102)
- RAM: 16 MiB (Zentel A3S28D40JTP-50)
- WLAN: Qualcomm Atheros TP9343 450Mbps
- Ethernet: Atheros AR8228/AR8229 4 port (100M)
添加TP9343芯片的路由器型号支持，TL-WR882N/WR885N/WR886N系列
* ath79: add support for MerCury MW4530R v1
重新添加水星MW4530R路由器支持
* Repair generate mw4530r firmware default is 8M
* ath79: add support for TP-Link TL-WR882N/WR885N/WR886N
This adds support for the various clones of the TL-WR885N recently
supported ("ath79: add support for TP-Link TL-WR885N v1"):
- tplink,tl-wr882n-v1
- tplink,tl-wr882n-v2
- tplink,tl-wr882n-v3
- tplink,tl-wr885n-v1
- tplink,tl-wr885n-v2
- tplink,tl-wr886n-v2
- tplink,tl-wr886n-v3
- tplink,tl-wr886n-v4
- tplink,tl-wr886n-v5
- tplink,tl-wr886n-v6
- tplink,tl-wr886n-v7
These devices are cloned in ar71xx. All models added in this patch are the same hardware CPU
WR885n V2 was tested.
Specifications:
- SOC: Qualcomm Atheros TP9343-AL3A
- CPU: 750MHz
- Flash: 2 MiB (AH1446 25Q16BS1G E5N102)
- RAM: 16 MiB (Zentel A3S28D40JTP-50)
- WLAN: Qualcomm Atheros TP9343 450Mbps
- Ethernet: Atheros AR8228/AR8229 4 port (100M)
添加TP9343芯片的路由器型号支持，TL-WR882N/WR885N/WR886N系列
* ath79: add support for MerCury MW4530R v1
重新添加水星MW4530R路由器支持
