Add options removed by `make kernel_oldconfig CONFIG_TARGET=subtarget', missing which causes compilation to stop and cause an error.
Fixes: 2a86425de1 ("x86: 6.6: refresh kernel config")
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
This is an automatically generated commit.
During a `git bisect` session, `git bisect --skip` is recommended.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
This is an automatically generated commit.
During a `git bisect` session, `git bisect --skip` is recommended.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
This reverts commit 3004c20614.
The commit added the needed packages for the new target
to the generic x86_64 image. This results into unwanted
modules and firmware files for other x86 devices.
Additionally, there is the following error message
while booting the image on other x86 devices:
[ 8.531720] kmodloader: 1 module could not be probed
[ 8.532613] kmodloader: - leds-mlxcpld - 0
For now, the needed packages will have to be selected
manually while configuring the image.
Signed-off-by: Til Kaiser <til.kaiser@gmx.de>
GRUB_SERIAL is also used for the default serial on the target and not
only in grub. When no grub was build it was not available and the build
fails.
Rename GRUB_SERIAL to TARGET_SERIAL and make it always available on x86
and armsr targets.
Fixes: #14063
Fixes: b10768476f ("x86,armsr: interpolate GRUB_SERIAL into /etc/inittab")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some platforms have their console on other ports than ttyS0, so
allow the developer to tailor this on bespoke platform images.
Fixes issue #13401.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
CONFIG_DEVTMPFS_SAFE is now part of the generic configuration. Remove it
from the target configurations.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Mellanox Spectrum SN2000 Series Switches are Managed Ethernet
Switches with a maximum speed of 100Gb/s and up to 56 ports.
Tested on a Mellanox Spectrum SN2100 with the following specs:
- CPU: Intel ATOM x86 dual-core 2.4GHz
- RAM: 8GB
- Disk: 16GB SSD
- Ports: 16x QSFP28 100GbE, 1x 100M Mgmt Port, 1x RJ45 Serial Port
- USB: 1x mini 2.0
- Button: 1x (reset)
- LEDs: 6x
Installation:
- Create a bootable USB device (either by flashing this image
onto it or another Linux distribution)
- Unzip the generic OpenWrt x64 image
and copy it onto the USB device
- Plug the USB device into the Mellanox Switch and boot from it
- Flash the image (e.g., with dd) onto the internal SSD
of the switch (should be /dev/sda)
To enter the BIOS, reboot the switch and press CTRL+B while you see
the BIOS information text (American Megatrends …). The default password
to enter the BIOS is admin. To boot from the USB device, switch to the
Boot index tab and set your USB device at the top of the boot order
(the internal SSD should be currently there). Don't forget to set
the SSD back at the top after you have flashed the image.
Signed-off-by: Til Kaiser <til.kaiser@gmx.de>
[unify with generic x64 image]
Signed-off-by: David Bauer <mail@david-bauer.net>
CONFIG_DEVTMPFS_SAFE and CONFIG_DM_AUDIT were not
set and had to be manually selected during build
everytime kernel was updated.
Signed-off-by: Oskari Rauta <oskari.rauta@gmail.com>
When the membase and pci_dev pointer were moved to a new struct in priv,
the actual membase users were left untouched, and they started reading
out arbitrary memory behind the struct instead of registers. This
unfortunately turned the RNG into a constant number generator, depending
on the content of what was at that offset.
To fix this, update geode_rng_data_{read,present}() to also get the
membase via amd_geode_priv, and properly read from the right addresses
again.
Closes#13417.
Reported-by: Timur I. Davletshin <timur.davletshin@gmail.com>
Tested-by: Timur I. Davletshin <timur.davletshin@gmail.com>
Suggested-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
This compiles the CONFIG_PTP_1588_CLOCK support into the kernel binary
and activates the drivers for KVM and VMware which allow syncing the
host time with the VM when OpenWrt is running in a VM. With this change
the CONFIG_HYPERV_UTILS driver is now build into the kernel, because it
depends on the PTP framework being compiled in. CONFIG_HYPERV_UTILS was
build as a module, but not packages before.
Fixes: #13277
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
