Commit Graph

4255 Commits

Author SHA1 Message Date
AmadeusGhost
b55a3c14e7 rockchip: fixes pcie eth compatible for r4s
Use the standard pci device binding to fixes this.

Signed-off-by: AmadeusGhost <amadeus@immortalwrt.org>
2022-05-18 21:00:33 +08:00
Ptilopsis Leucotis
d0cbcb5782 ath79: fix I2C on GL-AR300M devices
On GL-AR300M Series GPIO17 described as I2C SDA in Device Tree.
Because of GPIO_OUT_FUNCTION4 register was not initialized on start,
GPIO17 was uncontrollable, it always in high state. According to QCA9531
documentation, default setting of GPIO17 is SYS_RST_L. In order to make
GPIO17 controllable, it should write value 0x00 on bits [15:8] of
GPIO_OUT_FUNCTION4 register, located at 0x1804003C address.

Signed-off-by: Ptilopsis Leucotis <PtilopsisLeucotis@yandex.com>
2022-05-18 20:44:14 +08:00
Tamas Balogh
d06de144c5 ramips: add led_source for Asus RT-AC1200 devices
this adds the mediatek,led_source dts binding for
Asus RT-AC1200 devices' dtsi, for correct switch LED
behavior.

The dts-binding is introduced in commit:
65dc9e0980

Without this, we only have constantly very fast
blinking LEDs, which don't react on any traffic or
LAN events at all.

Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
2022-05-18 20:44:11 +08:00
Andreas Böhler
3e2f1c49c4 ramips: Add support for SERCOMM NA502S
The SERCOMM NA502s is a smart home gateway manufactured by SERCOMM and sold
under different brands (among others, A1 Telekom Austria SmartHome Premium
Gateway). It has multi-protocol radio support in addition to LAN and WiFi.

Note: BLE and audio are currently unsupported.

Specifications
--------------

  - MT7621ST 880MHz, Single-Core, Dual-Thread
  - MT7603EN 2.4GHz WiFi
  - MT7662EN 5GHz WiFi + BLE
  - 128MiB NAND
  - 256MiB DDR3 RAM
  - SD3503 ZWave Controller
  - EM357 Zigbee Coordinator
  - Telit UMTS module
  - Rechargeable battery
  - speaker and microphone

MAC address assignment
----------------------

LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches
the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the
OEM firmware does not enable 5GHz WiFi.

Installation
------------
Attach serial console, then boot the initramfs image via TFTP.
Once inside OpenWrt, run sysupgrade -n with the sysupgrade file.

Attention: The device has a dual-firmware design. We overwrite kernel2,
since kernel1 contains an automatic recovery image.

If you get NAND ECC errors and are stuck with bad eraseblocks, try to
erase the mtd partition first with

mtd unlock ubi
mtd erase ubi

This should only be needed once.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2022-05-18 20:42:19 +08:00
Alessio Prescenzo
2e9e7727ad ramips: add support for Cudy X6
Specifications:

SoC: MediaTek MT7621
RAM: 256 MB
Flash: 32 MB
WiFi: MediaTek MT7915E
Switch: 1 WAN, 4 LAN (Gigabit)
Ports: 1 USB 3.0
Buttons: Reset, WPS
LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB
Power: DC 12V 1A tip positive
Installation:

Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.

Recovery:

Loads only signed manufacture firmware due to bootloader RSA verification
serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
connect to any lan ethernet port
power on the device while holding the reset button
wait at least 8 seconds before releasing reset button for image to
download

Signed-off-by: Alessio Prescenzo <alessioprescenzo@gmail.com>
[ensure unique wireless MAC, fix GPIO pingroup]
Signed-off-by: David Bauer <mail@david-bauer.net>
2022-05-18 20:41:11 +08:00
Tianling Shen
624764267d
rockchip: drm-rockchip: fix Kconfig
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 6957f13eea)
2022-05-17 17:19:12 +08:00
Tianling Shen
991fab8bd1
Merge Mainline
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2022-05-17 17:06:47 +08:00
Piotr Dymacz
af0a1035c7 ramips: fix booting on Samknows SK-WB8
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of similar devices.

Fixes: #9824
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2022-05-17 00:14:38 +08:00
Josef Schlehofer
19d556319e
armvirt/64: change it to cortex-a53 instead of generic
Package architecture aarch64_generic [1] can be used just with three
devices. One is NanoPI R2S and then there are two development boards
from NXP. Let's change armvirt/64 to Cortex A53 (aarch64_cortex-a53)
[2]. It has wider support by multiple devices like NanoPI Neo Plus2/Core2,
ESPRESSObin, Pine64, and Raspberry Pi 2&3.

While looking at ARMvirt/32 it has set CPU_TYPE and CPU_SUBTYPE to be
arm_cortex-a15_neon-vfpv4 [3]. It has support to devices like
Linksys EA8500 v1, Linksys EA7500 v1, Netgear D7800, Netgear R7500 and so on.

Tested with:
qemu-system-aarch64 -m 1024 -smp 2 -cpu cortex-a57 -M virt -nographic \
-kernel openwrt-armvirt-64-Image-initramfs

Successfully compiled and booted.
Here goes the output:
root@OpenWrt:/# uname -a
Linux OpenWrt 5.4.82 #0 SMP Sun Dec 13 12:52:10 2020 aarch64 GNU/Linux
root@OpenWrt:/# cat /etc/openwrt_release
DISTRIB_ID='OpenWrt'
DISTRIB_RELEASE='SNAPSHOT'
DISTRIB_REVISION='r15207-96fca0f807'
DISTRIB_TARGET='armvirt/64'
DISTRIB_ARCH='aarch64_cortex-a53'
DISTRIB_DESCRIPTION='OpenWrt SNAPSHOT r15207-96fca0f807'
DISTRIB_TAINTS='no-all'

Also, change BOARDNAME to be the same as it is in armvirt/32.

[1] https://openwrt.org/docs/techref/instructionset/aarch64_generic
[2] https://openwrt.org/docs/techref/instructionset/aarch64_cortex-a53
[3] https://openwrt.org/docs/techref/instructionset/arm_cortex-a15_neon-vfpv4

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit 222dc0ad91)
2022-05-15 13:50:17 +08:00
Tomasz Maciej Nowak
db99e1851d
tegra: correct cpu subtype
Tegra 2 processors have only 16 double-precision registers. The change
introduced by 8dcc108760 ("toolchain: ARM: Fix toolchain compilation
for gcc 8.x") switched accidentally the toolchain for tegra target to cpu
type with 32 double-precision registers. This stems from gcc defaults
which assume "vfpv3-d32" if only "vfpv3" as mfpu is specified. That
change resulted in unusable image, in which kernel will kill userspace as
soon as it causing "Illegal instruction".

Ref: https://forum.openwrt.org/t/gcc-was-broken-on-mvebu-armada-370-device-after-commit-on-2019-03-25/43272
Fixes: 8dcc108760 ("toolchain: ARM: Fix toolchain compilation for
gcc 8.x")
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
(cherry picked from commit 43d1d88510)
2022-05-14 14:53:22 +08:00
Tomasz Maciej Nowak
c812f84eaf
mvebu: cortexa9: correct cpu subtype
Armada 370  processors have only 16 double-precision registers. The
change introduced by 8dcc108760 ("toolchain: ARM: Fix toolchain
compilation for gcc 8.x") switched accidentally the toolchain for mvebu
cortexa9 subtarget to cpu type with 32 double-precision registers. This
stems from gcc defaults which assume "vfpv3-d32" if only "vfpv3" as mfpu
is specified. That change resulted in unusable image, in which kernel
will kill userspace as soon as it causing "Illegal instruction".

Ref: https://forum.openwrt.org/t/gcc-was-broken-on-mvebu-armada-370-device-after-commit-on-2019-03-25/43272
Fixes: 8dcc108760 ("toolchain: ARM: Fix toolchain compilation for
gcc 8.x")
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
(cherry picked from commit 2d61f8821c)
2022-05-14 14:52:20 +08:00
Tianling Shen
af2f2d70a2
ixp4xx: add missing Kconfig
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2022-05-14 14:14:23 +08:00
Tianling Shen
ae00ad5376
ixp4xx: add missing Kconfig
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2022-05-14 13:40:58 +08:00
Tianling Shen
3c396e2eef
kernel: sfp: fix build
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2022-05-13 21:05:31 +08:00
Tianling Shen
86bd28fc33
mpc85xx: p1020: add missing Kconfig
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2022-05-13 19:56:49 +08:00
Tianling Shen
7db29197e0
kernel: generic: add missing Kconfig
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2022-05-13 19:45:38 +08:00
Hauke Mehrtens
6feb6d726a
ramips: Deactivate NETGEAR WNCE2001 by default
The root file system is getting too big for this device and this breaks
the ramips/rt305x build.

Do not build images for this board by default to fix this problem.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f46a3c7b14)
2022-05-13 19:32:46 +08:00
Tianling Shen
be03a0e6aa
octeontx: add missing Kconfig
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2022-05-13 19:27:58 +08:00
Tianling Shen
88dd5b530b
armvirt: 64: add missing Kconfig
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2022-05-13 19:01:02 +08:00
Adrian Schmutzler
107c5d097c
ath25: disable devices with 4M flash
Devices with 4M flash are not built be default for 20.xx anymore.

Building them with buildbot settings does not work anymore anyway.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit ad22f6a8aa)
2022-05-13 18:23:02 +08:00
Tianling Shen
1e1772cc1e
rt3883: disable build for rt-n56u by default
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 1d1ba8d711)
2022-05-13 18:19:55 +08:00
Tianling Shen
4915d34e9e
kernel: bump to 4.9.313, 4.14.278, 4.19.242
Removed patches:
- bcm27xx/patches-4.19/950-0475-usb-xhci-Disable-the-XHCI-5-second-timeout.patch
    Should be fixed by upstream commit 1c713660c51f3bc64fc1c709ba2bfb358551f3da
      ("xhci: make xhci_handshake timeout for xhci_reset() adjustable").

Refreshed all patches.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2022-05-13 18:03:49 +08:00
Eneas U de Queiroz
5422b6537c mediatek: remove crypto-hw-mtk package
The MediaTek's Crypto Engine module is only available for mt7623, in
which case it is built into the kernel.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2022-05-10 14:37:21 +08:00
Tamas Balogh
1a59a425f7 ramips: ethernet: ralink: add led_source dts-binding
this adds the new dts-binding "mediatek,led_source"
currently for MT7628AN and MT7688 built-in switches,
which is documented as a 3-bit field configuring the
switch LEDs for various control schemes from 0 to 3.

Normally this is not needed, but e.g. for Asus RT-AC1200-V2
it is a must to set it to the anyway undocumented value
of 4, to have the switch LEDs react correctly on link/act
events. This is an MT7628DAN device, but I doubt this is
a speciality of this particular SoC.

Also added the RT305X_ESW_LED_OFF value to LED states.
Did also rename the register RT5350_EWS_REG_LED_POLARITY
to RT5350_EWS_REG_LED_CONTROL, which is the correct name.
Also making use of defines for some hardcoded values.

Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
2022-05-09 17:15:44 +08:00
Ptilopsis Leucotis
fe22b54a6f ramips: add i2c in dts for GL-MT300N-V2
According wiki https://docs.gl-inet.com/en/2/hardware/mt300n-v2/
GL-MT300N-V2 have I2C interface on GPIO4, GPIO5.
Adding I2C in device tree make possible using I2C on this device.

Signed-off-by: Ptilopsis Leucotis <PtilopsisLeucotis@yandex.com>
2022-05-09 17:15:34 +08:00
Alban Bedel
b35bed5efa ramips: zbt-wg2626: Fix the LAN ports names
The current names don't match with the labels on the case, reverse
the LAN ports order so they match.

Signed-off-by: Alban Bedel <albeu@free.fr>
2022-05-09 17:13:39 +08:00
Alban Bedel
0becf0779e ramips: zbt-wg2626: Add the reset gpio for PCIe port 1
The 2.4GHz interface doesn't come up properly with the log showing:

    mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)

As seen on other MT7621 boards this is caused by a missing reset GPIO.
The MT7621 dtsi set GPIO 19 as PCIe reset GPIO, which on this board
reset the 5GHz interface on port 0. Add GPIO 8 to the PCIe reset GPIO
list to also reset the 2.4GHz interface on port 1.

Signed-off-by: Alban Bedel <albeu@free.fr>
2022-05-09 17:13:16 +08:00
PtilopsisLeucotis
e03edf24cd ath79: add USB power control for GL-AR300M series
Add USB power control in DTS for GL.iNet models:
- AR300M;
- AR300M-Ext;
- AR300M16;
- AR300M16-Ext.

Signed-off-by: PtilopsisLeucotis <PtilopsisLeucotis@yandex.com>
2022-05-09 17:12:17 +08:00
Foica David
0e7907dc5c ath79: add support for TP-Link Deco M4R v1 and v2
This commit adds support for the TP-Link Deco M4R (it can also be M4,
TP-Link uses both names) v1 and v2. It is similar hardware-wise to the
Archer C6 v2. Software-wise it is very different. V2 has a bit different
layout from V1 but the chips are the same and the OEM firmware is the same
for both versions.

Specifications:
SoC: QCA9563-AL3A
RAM: Zentel A3R1GE40JBF
Wireless 2.4GHz: QCA9563-AL3A (main SoC)
Wireless 5GHz: QCA9886
Ethernet Switch: QCA8337N-AL3C
Flash: 16 MB SPI NOR

Flashing:

The device's bootloader only accepts images that are signed using
TP-Link's RSA key, therefore this way of flashing is not possible. The
device has a web GUI that should be accessible after setting up the device
using the app (it requires the app to set it up first because the web GUI
asks for the TP-Link account password) but for unknown reasons, the web
GUI also refuses custom images.

There is a debug firmware image that has been shared on the device's
OpenWrt forum thread that has telnet unlocked, which the bootloader will
accept because it is signed. It can be used to transfer an OpenWrt image
file over to the device and then be used with mtd to flash the device.

Pre-requisites:

- Debug firmware.
- A way of transferring the file to the router, you can use an FTP server
  as an example.
- Set a static IP of 192.168.0.2/255.255.255.0 on your computer.
- OpenWrt image.

Installation:

- Unplug your router and turn it upside down. Using a long and thin object
  like a SIM unlock tool, press and hold the reset button on the router and
  replug it. Keep holding it until the LED flashes yellow.
- Open 192.168.0.1. You should see the bootloader recovery's webpage.
  Choose the debug firmware that you downloaded and flash it. Wait until the
  router reboots (at this stage you can remove the static IP).

- Open a terminal window and connect to the router via telnet (the primary
  router should have a 192.168.0.1 IP address, secondary routers are
  different).
- Transfer the file over to the router, you can use curl to download it
  from the internet (use the insecure flag and make sure your source accepts
  insecure downloads) or from an FTP server.
- The router's default mtd partition scheme has kernel and rootfs
  separated. We can use dd to split the OpenWrt image file and flash it with
  mtd:

   dd if=openwrt.bin of=kernel.bin skip=0 count=8192 bs=256
   dd if=openwrt.bin of=rootfs.bin skip=8192 bs=256

- Once the images are ready, you have to flash the device using mtd
  (make sure to flash the correct partitions or you may be left with a
  hard bricked router):

   mtd write kernel.bin kernel
   mtd write rootfs.bin rootfs

- Flashing is done, reboot the device now.

Signed-off-by: Foica David <superh552@gmail.com>
2022-05-09 17:11:54 +08:00
Davide Fioravanti
a1bc5ab0b1 ramips: add support for Wavlink WL-WN533A8
The Wavlink WL-WN533A8 is an AC3000 router with 5 gigabit ethernet ports
and one USB 3.0 port.
It's also known as Wavlink QUANTUM T8.

Hardware
--------
SoC:   Mediatek MT7621A
RAM:   128MB (Nanya NT5CB64M16GP-EK)
FLASH: 16MB NOR (GigaDevice GD25Q127CSIG3)
ETH:
  - 5x 10/100/1000 Mbps Ethernet (4x LAN + 1x WAN)
WIFI:
  - 1x MT7615DN (2x 2x2:2) 2.4GHz and 5GHz DBDC
  - 1x MT7615NE (4x4:4) 5GHz
  - 8 external antennas
BTN:
  - 1x Reset button
  - 1x WPS button
  - 1x Turbo button
  - 1x Touchlink button
  - 1x ON/OFF switch
LEDS:
  - 1x Red led (system status)
  - 1x Blue led (system status)
  - 7x Blue leds (wifi led + 5 ethernet ports + power)
USB:
  - 1x USB 3.0 port
UART:
  - 57600-8-N-1
    J4

Everything works correctly.

Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
(Procedure tested on fw M33A8.V5030.190716 and M33A8.V5030.201204)

Restore OEM Firmware
--------------------
Flash the firmware update available online directly from LUCI.
You can download it from:
https://www.wavlink.com/en_us/firmware/details/f2d247ecba.html
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.

Notes
-----
1) Router mac addresses:
   LAN		XX:XX:XX:XX:XX:63 (factory @ 0xe006)
   WAN		XX:XX:XX:XX:XX:64 (factory @ 0xe000)
   WIFI 2G/5G	XX:XX:XX:XX:XX:65 (factory @ 0x04)
   WIFI 5G	XX:XX:XX:XX:XX:66 (factory @ 0x8004)

   LABEL	XX:XX:XX:XX:XX:65

   In OEM firmware the DBDC wifi interfaces have these mac addresses:
     2G) 82:XX:XX:XX:XX:65
     5G) 80:XX:XX:XX:XX:65

   While in OpenWrt the addresses are:
     2G) 80:XX:XX:XX:XX:65
     5G) 02:XX:XX:XX:XX:65

2) radio0 will show as 2G/5G interface but only 2G is really usable.

3) There is just one wifi led for all wifi interfaces.
   It currently shows only the radio0 GHz wifi activity.

4) My unit was shipped with M33A8.V5030.190716 firmware which contains
   the http://192.168.10.1/webcmd.shtml page. Entering "telnetd" in
   the input box it will start the telnet daemon. Now you can access
   the telnet console on port 2323 with these credentials:
     username: admin2860
     password: admin

5) The M33A8.V5030.201204 firmware version, doesn't contain anymore the
   webcmd.shtml page. If your router is shipped with a previous firmware
   version and you want to back it up, you can follow the back up
   procedure of the WS-WN583A6.

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2022-05-09 17:09:46 +08:00
Davide Fioravanti
98c36e8a8c ramips: create shared DTSI for Wavlink WN53XAX devices
Most of the definitions for WN531A6 will be shared with WN533A8 in a
future commit, so put them in a shared DTSI.

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2022-05-09 17:08:15 +08:00
Tianling Shen
db825d3f38
x86: drop duplicate sets
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 7014ff8199)
2022-05-05 12:19:39 +08:00
Tianling Shen
6bc7e9db52
ath79: drop orphan csac detection
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 0e2fa122b9)
2022-05-04 14:58:32 +08:00
AmadeusGhost
c46b59b2ed ipq806x: m520: simplified image generation 2022-05-01 12:15:55 +08:00
Tianling Shen
d57e50ab46
x86: use vendor driver of r8152 for better compatibility
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit b3e29a6478)
2022-04-29 18:24:19 +08:00
Jax Jiang
02d896101d
x86: grub2: search for the "kernel" filesystem on all disks
Previously, grub2 was hardcoded to always look on "hd0" for the
kernel.

This works well when the system only had a single disk.
But if there was a second disk/stick present, it may have look
on the wrong drive because of enumeration races.

This patch utilizes grub2 search function to look for a filesystem
with the label "kernel". This works thanks to existing setup in
scripts/gen_image_generic.sh. Which sets the "kernel" label on
both the fat and ext4 filesystem variants.

Signed-off-by: Jax Jiang <jax.jiang.007@gmail.com>
Suggested-by: Alberto Bursi <bobafetthotmail@gmail.com> (MX100 WA)
(word wrapped, slightly rewritten commit message, removed MX100 WA)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 1050e66c8f)
2022-04-29 10:15:04 +08:00
Martin Schiller
b14737143f layerscape: armv7: refresh config-5.10
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2022-04-28 14:59:48 +08:00
Martin Schiller
5086ebd50c layerscape: armv7: copy config-5.4 to config-5.10
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2022-04-28 14:59:37 +08:00
Martin Schiller
9f4b4fd246 layerscape: armv8_64b: refresh config-5.10
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2022-04-28 14:59:21 +08:00
Martin Schiller
d1088ecbb5 layerscape: armv8_64b: copy config-5.4 to config-5.10
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2022-04-28 14:59:07 +08:00
Martin Schiller
c9af2491c9 layerscape: armv8_64b: use non-SDK dts files for linux-5.10 or newer
Since we decided to drop the LSDK patches with linux-5.10, we now have
to switch to the corresponding upstream dts files as well.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2022-04-28 14:56:26 +08:00
Martin Schiller
5903043f88 layerscape: armv8_64b: fix KERNEL_LOADADDR for linux >= 5.8
In kernel versions newer than 5.8 the arm64 TEXT_OFFSET (0x80000) has
been set to 0x0 (and later removed). This will break Uimages with kernel
load addresses that aren't 2MiB aligned any longer. Resulting in the
kernel silently fail to boot. For layerscape armv8_64b targets this
needs to be changed to 0x80000000 (start of RAM).

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2022-04-28 14:56:15 +08:00
Martin Schiller
f4eaa4b1c5 layerscape: add patches for kernel 5.10
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2022-04-28 14:55:59 +08:00
Martin Schiller
32a9b5e07c layerscape: add kernel 5.10 as testing version
This patch adds "KERNEL_TESTING_PATCHVER:=5.10" to the Makefile in
layerscape target to allow using Kernel 5.10 for testing.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2022-04-28 14:55:46 +08:00
Martin Schiller
474cab3411 layerscape: remove unneeded KERNEL_ENTRY_POINT definition
As KERNEL_ENTRY_POINT is identical to KERNEL_LOADADDR, drop it.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2022-04-28 14:50:23 +08:00
Arınç ÜNAL
6934c7dff7 ramips: mt7621-dts: add pinctrl properties for ethernet
Add the missing pinctrl properties on the ethernet node.
GMAC1 will start working with this change.

Link: https://lore.kernel.org/netdev/83a35aa3-6cb8-2bc4-2ff4-64278bbcd8c8@arinc9.com/

Overwrite pinctrl-0 property without rgmii2_pins on devicetrees which use
the rgmii2 pins as GPIO (22 - 33).

Give gpio function to rgmii2 pin group on mt7621_tplink_archer-x6-v3.dtsi
which uses GPIO 28.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2022-04-26 14:28:43 +08:00
Arınç ÜNAL
94bfa451d7 ramips: mt7621-dts: enable flow control on port@6
Flow control needs to be enabled on both sides to work.
It is already enabled on gmac0, enable it on port@6 too.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Sungbo Eo <mans0n@gorani.run>
2022-04-26 14:27:50 +08:00
Arınç ÜNAL
66854abbd9 ramips: mt7621-dts: fix switch@1f warnings
Remove reg property from ports node to fix this warning:

Warning (unit_address_vs_reg): /ethernet@1e100000/mdio-bus/switch@1f/ports: node has a reg or ranges property, but no unit name

Another warning surfaces afterwards. Remove #address-cells and #size-cells
from switch@1f node to fix this warning:

Warning (avoid_unnecessary_addr_size): /ethernet@1e100000/mdio-bus/switch@1f: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2022-04-26 14:27:24 +08:00
Sergio Paracuellos
735ea62ae8 ramips: mt7621-dts: properly organize pcie node
Device tree pcie node for this SoC is using different
styles in its different properties. Hence properly
unify them to be able to write a a proper yaml schema
documentation.

Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210505121736.6459-11-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-26 14:25:31 +08:00
Sergio Paracuellos
f5a463c669 ramips: mt7621-dts: add missing device_type in pcie root ports
According to the YAML schema 'pci-bus.yaml' the 'device_type'
property is mandatory for all pcie root ports. Hence add it.

Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210506170742.28196-3-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-26 14:25:02 +08:00