The previous config will only show 2.4G radio activity status
This change mr24:green:wifi4 and mr24:green:wifi2 to
show 2.4G and 5G radio on and off status
change mr24:green:wifi3 and mr24:green:wifi1 to
show 2.4G and 5G radio activity status
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
Backport a pending patch already reviewed that fix some warning about tsens debugs already registered.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
With some talk with the ARM maintainer, it was notice that enlarging the limit
to the current value is VERY wrong and clash with other memory.
A better solution would be to reduce the IO space from 1MB to 64K as probably
it's a long lasting typo and even x86 arch doesn't have a IO space that big.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Removed upstreamed:
generic/pending-5.4/770-02-net-ethernet-mtk_eth_soc-fix-rx-vlan-offload.patch
All other patches automatically rebased.
Build system: x86_64
Build-tested: ipq806x/R7800
Note that since I rebased the previous commit, I removed my Run-tested line
although I confirm building the image successfully.
Signed-off-by: John Audia <graysky@archlinux.us>
Removed upstreamed:
generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch
bcm63xx/patches-5.4/434-nand-brcmnand-fix-OOB-R-W-with-Hamming-ECC.patch*
Removed/code was included upstream and therefore redundant:
ramips/patches-5.4/999-fix-pci-init-mt7620.patch
All other patches automatically rebased.
* update_kernel.sh did not flag this yet it was included in 5.4.119[1], as a
result of the rebase, I removed my testing lines since I did not go back to
test built or to run test 5.4.119 with the removed patch present.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.4.119&id=e5b3e69eb36ac1178a7a2392616fd29afd288c4e
Signed-off-by: John Audia <graysky@archlinux.us>
This switches device names to the common 'vendor_model' approach as in
most of other targets in OpenWrt.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
- drop unused 'UBOOT' variable from 'Device/apalis' recipe
- fix 'KERNEL_SUFFIX' for 'Device/cubox-i' (should be '-zImage')
- drop redundant 'DEVICE_{VENDOR,MODEL}' from 'Device/ventana-large'
- other, minor fixes
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This reduces redundant instructions.
The solution is inspired by a different implemention of
Roman Kuzmitskii.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ZiKing CPE46B is a POE outdoor 2.4ghz device with an integrated directional
antenna. It is low cost and mostly available via Aliexpress, references can
be found at:
- https://forum.openwrt.org/t/anddear-ziking-cpe46b-ar9331-ap121/60383
- https://git.lsd.cat/g/openwrt-cpe46b
Specifications:
- Atheros AR9330
- 32MB of RAM
- 8MB of flash (SPI NOR)
- 1 * 2.4ghz integrated antenna
- 2 * 10/100/1000 ethernet ports (1 POE)
- 3 * Green LEDs controlled by the SoC
- 3 * Green LEDs controlled via GPIO
- 1 * Reset Button controlled via GPIO
- 1 * 4 pin serial header on the PCB
- Outdoor packaging
Flashing instruction:
You can use sysupgrade image directly in vendor firmware which is based
on OpenWrt/LEDE. In case of issues with the vendor GUI, the vendor
Telnet console is vulnerable to command injection and can be used to gain
a shell directly on the OEM OpenWrt distribution.
Signed-off-by: Giulio Lorenzo <salveenee@mortemale.org>
[fix whitespaces, drop redundant uart status and serial0, drop
num-chipselects, drop 0x1002 MAC address for wmac]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
COMFAST CF-E375AC is a ceiling mount AP with PoE support,
based on Qualcomm/Atheros QCA9563 + QCA9886 + QCA8337.
Short specification:
2x 10/100/1000 Mbps Ethernet, with PoE support
128MB of RAM (DDR2)
16 MB of FLASH
3T3R 2.4 GHz, 802.11b/g/n
2T2R 5 GHz, 802.11ac/n/a, wave 2
built-in 5x 3 dBi antennas
output power (max): 500 mW (27 dBm)
1x RGB LED, 1x button
built-in watchdog chipset
Flash instruction:
1) Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
2) TFTP
2.1) Set a tftp server on your machine with a fixed IP address of
192.168.1.10. A place the sysupgrade as firmware_auto.bin.
2.2) boot the device with an ethernet connection on fixed ip route
2.3) wait a few seconds and try to login via ssh
3) TFTP trough Bootloader
3.1) open the device case and get a uart connection working
3.2) stop the autoboot process and test connection with serverip
3.3) name the sysupgrade image firmware.bin and run firmware_upg
MAC addresses:
Though the OEM firmware has four adresses in the usual locations,
it appears that the assigned addresses are just incremented in a
different way:
interface address location
LAN: *:DC 0x0
WAN *:DD 0x1002
WLAN 2.4g *:E6 n/a (0x0 + 10)
WLAN 5g *:DE 0x6
unused *:DF 0x5006
The MAC address pointed at the label is the one assign to the LAN
interface.
Signed-off-by: Joao Henrique Albuquerque <joaohccalbu@gmail.com>
[add label-mac-device, remove redundant uart status, fix whitespace
issues, fix commit message wrapping, remove x bit on DTS file]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Ubiquiti EdgeRouter 6P is 6 port router with similar
specifications as the EdgeRouter 4, support for which was added
in commit dd651e54cc
There are five 10/100/1000 Mbps RJ/Copper ports and
one 1000 Mbps SFP port.
SoC: Octeon Cavium 7130 (Cavium 3) at 1000MHz
Memory: 1GiB DDR3
Flash: 2x2M chips with uboots (chainloaded) + 512K eeprom
LEDs: 1x for power status (white/blue, controllable)
and 6x for ethernet and SFP ports (no control over them)
Buttons: 1x Reset
Serial: 1x RJ45 port on front panel. 115200 baud, 8N1
USB: 1x USB3.0 on front panel
MII: 1x QSGMII from SoC
PHY: 1x Vitesse VSC8504 of which 4 ports are used (phys 4-7)
1x Vitesse VSC8514 of which 2 ports are used (phys 8-9)
Network port mapping
- eth0 on device maps to lan0 and phy5
- eth1 on device maps to lan1 and phy6
- eth2 on device maps to lan2 and phy7
- eth3 on device maps to lan3 and phy8
- eth4 on device maps to lan4 and phy9
- eth5 (SFP) on device maps to lan5 and phy4
What is not working:
- There is no port status available before it goes up
- SFP have no additional status and presented as no different from eth
- Power-over-ethernet (passive) support has not been tested
How to flash the firmware:
- copy openwrt-octeon-ubnt_edgerouter-6p-initramfs-kernel.bin and
openwrt-octeon-ubnt_edgerouter-6p-squashfs-sysupgrade.tar to
USB flash drive that is formatted to vfat/fat32
- connect USB flash drive to EdgeRouter 6P front USB port
- connect serial cable using front RJ45 port (115200 baud, 8N1)
- connect power to cable to EdgeRouter 6P
- connect terminal to the console to see uboot boot process
- interrupt boot by pressing button(s) on your keyboard to log
in to the uboot
- detect usb connected flash drives by typing to the console:
usb start
- after drive is detected load initramfs+kernel to the memory by typing:
fatload usb 0:1 0x20000000 openwrt-octeon-ubnt_edgerouter-6p-initramfs-kernel.bin
- after initramfs+kernel is loaded to the memory load it by typing:
bootoctlinux 0 numcores=4 endbootargs mem=0
- boot process should finish and you will be greeted with console
after pressing enter
- create directory to mount usb flash drive to by typing:
mkdir /tmp/sda
- mount flash drive to that directory by typing:
mount /dev/sda1 /tmp/sda
- flash firmware to router internal storage by typing:
sysupgrade /tmp/sda/openwrt-octeon-ubnt_edgerouter-6p-squashfs-sysupgrade.tar
- device will reboot and after it gets up you will have
edgerouter 6p running openwrt
Signed-off-by: Dan Brown <danbrown@gmail.com>
[reorder/squash patches, move ethernet@0 to DTS, share image setup]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
EdgeRouter 4 and upcoming EdgeRouter 6P and 12 have similar setup,
so create a shared DTSI to prevent duplicate code.
Signed-off-by: Dan Brown <danbrown@gmail.com>
[reorder/squash commits, add description, move ethernet@0 to DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Vendor firmware expects model name without manufacturer name inside
'supported_devices' part of metadata. This allows direct upgrade to
OpenWrt from vendor's GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This fixes a small regression where the lzma-loader variable values
are being shared between boards that require different configurations.
If not set to "" globally, a device without these settings will just take
the last values another device has set before in the queue.
Fixes: 1b8bd17c2d ("ath79: lzma-loader: allow setting custom kernel magic")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
[add detailed explanation to the commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The two device strings were not ordered properly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Before this commit, it was assumed that mkhash is in the PATH. While
this was fine for the normal build workflow, this led to some issues if
make TOPDIR="$(pwd)" -C "$pkgdir" compile
was called manually. In most of the cases, I just saw warnings like this:
make: Entering directory '/home/.../package/gluon-status-page'
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
[...]
While these were only warnings and the package still compiled sucessfully,
I also observed that some package even fail to build because of this.
After applying this commit, the variable $(MKHASH) is introduced. This
variable points to $(STAGING_DIR_HOST)/bin/mkhash, which is always the
correct path.
Signed-off-by: Leonardo Mörlein <me@irrelefant.net>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The code uses get_mtd_device_nm() which must be followed by a call to
put_mtd_device() once the handle is no longer used.
This fixes spurious shutdown console messages such as:
[ 2256.334562] Removing MTD device #7 (soft_config) with use count 1
Reported-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
The code uses get_mtd_device_nm() which must be followed by a call to
put_mtd_device() once the handle is no longer used.
This fixes spurious shutdown console messages such as:
[ 2256.334562] Removing MTD device #7 (soft_config) with use count 1
Reported-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Refresh kernel patches.
Built under MacOS
Run tested: x86_64 (apu2)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
311-MIPS-zboot-put-appended-dtb-into-a-section.patch
commit d2e850e96183 in kernel, part of v5.11
499-mtd-don-t-lock-when-recursively-deleting-partitions.patch
commit cb4543054c5c in kernel, part of v5.13
103-MIPS-select-CPU_MIPS64-for-remaining-MIPS64-CPUs.patch
commit 5a4fa44f5e1b in kernel, part of v5.13
Move them to backports folder to make maintainance easier.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Kernel 5.10 support for ipq806x was added at the same time that these
patches were developed for kernel 5.4. This carries the patches forward
to kernel 5.10.
fa731838c5 ipq806x: dwmac: clear forced speed during probe
75ca641f1b ipq806x: Add "snps,dwmac" to all gmac compatible=
d62825dd77 ipq806x: dwmac: set forced speed when using fixed-link
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Run-tested: ipq806x/ubnt,unifi-ac-hd
Cc: Ansuel Smith <ansuelsmth@gmail.com>
d53be2a2e9 migrated 0069-arm-boot-add-dts-files.patch from patches-5.4
to patches-5.10, but a subsequent patch in that set, 1e25423be8,
erroneously removed several devices:
ipq8062/nec,wg2600hp3 from 3bb1618573
ipq8064/asrock,g10 from 98b86296e6
ipq8064/ubnt,unifi-ac-hd from 4e46beb313
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Run-tested: ipq806x/ubnt,unifi-ac-hd
Cc: Ansuel Smith <ansuelsmth@gmail.com>
The out-of-tree qcom-smem patches traditionally displayed mtd partition names
in upper case, starting with the new mainline qcom-smem support in kernel v5.10,
it switches to normalizing the partition names to lower case.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
fa731838c5 cleared the forced speed in the QSGMII PCS_ALL_CH_CTL
register during probe, but this is only correct for GMACs that are not
configured with fixed-link. This prevented GMACs configured with both
phy-mode = "sgmii" and fixed-link from working properly, as discussed at
https://github.com/openwrt/openwrt/pull/3954#issuecomment-834625090 and
the comments that follow. Notably, this prevented all communication
between gmac2 and the switch on the Netgear R7800.
The correct behavior is to set the QSGMII PCS_ALL_CH_CTL register by
considering the gmac's fixed-link child, setting the speed as directed by
fixed-link if present, and otherwise clearing it as was done previously.
Fixes: fa731838c5 ("ipq806x: dwmac: clear forced speed during probe")
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Hannu Nyman <hannu.nyman@iki.fi>
Run-tested: ipq806x/ubnt,unifi-ac-hd, ipq806x/netgear,r7800
Cc: Petr Štetiar <ynezz@true.cz>
Cc: Ansuel Smith <ansuelsmth@gmail.com>
Tested-by: Ansuel Smith <ansuelsmth@gmail.com>
wakeup-source is required for gpio keys to fix error
genirq: irq_chip msmgpio did not update eff. affinity mask
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
- Add new tsens node
- Add new cpufreq required nodes
- Drop arm cpuidle compatible
- Fix duplicate node set upstream
- Add voltage tolerance value for cpu opp
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
ipq806x have different ecc configuration for boot partition and rootfs partition. Add support for this to fix IO error on mtd block scan.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
