Hardware
--------
RockChip RK3568 ARM64 (4 cores)
2/4/8GB LPDDR4x RAM
1000 Base-T
2500 Base-T
AP6275S Wi-Fi 6 / Bluetooth 5.3
2 LEDs (RED / GREEN)
8/16/32/64GB eMMC on-board
Micro-SD Slot
HDMI Port
USB 2.0 Port
USB 3.0 Port
USB Type-C 3.0 Port
M.2 M-Key
40-Pin Header
USB PD 2.0 9/12/15V Power
Installation
------------
Uncompress the ImmortalWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit a609a18fb9)
Some devices lock up on PCIe initialization:
[ 64.309697] PCIe: Port 0 in endpoint mode, skipping.
[ 64.320496] PCIe: Initializing port 1
[ 64.325257] PCIe: BIST FAILED for port 1 (0xffffffffffffffff)
(system hangs here)
Given the ER contains no PCIe peripherals, has no way to attach any
and the stock kernel doesn't have PCIe support either, just disable it.
(cherry picked from commit 308630aea6)
Signed-off-by: Jakob Haufe <sur5r@sur5r.net>
Link: https://github.com/openwrt/openwrt/pull/16223
Signed-off-by: Robert Marko <robimarko@gmail.com>
Sometimes the mmc deivce may come up later than kernel attempts to
mount rootfs, resulting kernel panic. Enable rootwait to fix it.
Reported-by: Yangyu Chen <cyy@cyyself.name>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/15077
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
According to RTL8221B's datasheet, the PHY requires at least 10ms
for assert and 68ms (recommended) for de-assert. So increase the
assert/de-assert time to 15ms and 68ms respectively.
Fixes: c0c3234e17 ("mediatek: add support for JDCloud RE-CP-03")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16106
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d1954aa535)
Fixes: 0fc833f310 ("rockchip: enable wifi and bt for firefly station p2")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit c352e9438d)
The vendor U-Boot on the Cudy M3000 and the Yuncore AX835 assign random
mac addresses on boot and set the 'local-mac-address' property which
prevents Openwrt from assigning the correct address from evmem.
This patch removes the alias for ethernet0 so that U-Boot doesn't add the
property, removes the workaround from 02_network, and adds back the nvmem
definition for the M3000.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
(cherry picked from commit a55ab9e134)
Hardware:
SoC: MT7981b
RAM: 256 MB
Flash: 128 MB SPI NAND
Ethernet:
1x 2.5Gbps (rtl8221b)
1x 1Gbps (integrated phy)
WiFi: 2x2 MT7981
Buttons: Reset, WPS
LED: 1x multicolor
Solder on UART:
- remove rubber ring on the bottom
- remove screws
- pull up the cylinder, maybe help by push on an ethernet socket with a screwdriver
- remove the (3) screws holding the board in the frame
- remove the board from the frame to get to the screws for the silver, flat heat shield
- remove the (3) screws holding the heat shield
- solder UART pins to the back of the board
- make sure to have the pins point out on side with the black, finned heat spread
- the markings for the pins are going to be below the silver heat shield
- Vcc is not needed
If you don't intend on using the UART outside of the installation process, you might not
want to solder:
- carefully scrape off the thin layer of epoxy on the holes (not the copper)
- place your pin header with the UART attached in the holes
- the pins, starting with the one closest to the socket:
- Vcc (not required)
- GND
- RX
- TX
- either wedge the header or hold it with your fingers so that the pins stay in contact with the board
Installation (UART):
- attach an Ethernet cable to the 1Gbps port (black) on the router
- hold the reset button while powering the router
- press CTRL-C or wait for the timeout to get to the U-Boot prompt
- prepare a TFTP server on the network to supply ..-initramfs-kernel.bin
- use 'tftpboot' in the U-Boot shell to pull the image
- boot the image using 'bootm'
- push the ..-sysupgrade to the router using your preferred method
- perform the upgrade with 'sysupgrade -n'
There is a recovery mechanism that involves fetching a file called 'recovery.bin' but that is not understood yet.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
(cherry picked from commit 20e4a18feb)
The MAC address assigned to lan/wan was reversed.
Fixes: 6e51ff88b0 ("mediatek: add support for JDCloud RE-CP-03")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
With upstream accepted "mac-base" binding there is no need for a
downstream "mac-address-ascii" workaround anymore.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit daaa0c1b25)
Link: https://github.com/openwrt/openwrt/pull/15917
In the past few years, we have received several reports about SPI
Flash not working properly. This is caused by excessively fast
clock frequency. It's really annoying to fix them one by one. Let's
reduce these aggressive frequencies to 50 MHz. This is a safe and
suggested value in the vendor SDK.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 73eeac49be)
Link: https://github.com/openwrt/openwrt/pull/15919
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The WLAN + WED reset sequence relies on being able to receive interrupts from
the card, in order to synchronize individual steps with the firmware.
When WED is stopped, leave interrupts running and rely on the driver turning
off unwanted ones.
WED DMA also needs to be disabled before resetting.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 2c5b3bee38)
Add patch implementing operations to get and set flow-control link
parameters of mtk_eth_soc via ethtool.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 4a2f712f85)
Import patch accepted upstream.
Initial import:
- net: ethernet: mtk_ppe: Change PPE entries number to 16K
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 27b6838afa)
In preparation to update mtk_eth_soc move accepted patches from mediatek
target to backport folder, so other patches on top can be applied more
easily.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 8730f9e536)
Specifications:
- Device: Edimax BR-6208AC V2
- SoC: MT7620A
- Flash: 16 MiB
- RAM: 64 MiB
- Switch: 1 WAN, 3 LAN (10/100 Mbps)
- WiFi: MT7620 2.4 GHz + MT7610E 5 GHz
- LEDs: 1x POWER (green, not configurable)
1x Firmware (green, configurable)
1x Internet (green, configurable)
1x VPN (green, configurable)
1x 2.4G (green, not configurable)
1x 5G (green, not configurable)
Normal installation:
- Upload the sysupgrade image via the default web interface
Installation with U-Boot and TFTP:
- Requires a TFTP server which provides the sysupgrade image
- Requires a connection to the serial port of the device, rate 57600
Signed-off-by: Stefan Weil <sw@weilnetz.de>
(cherry picked from commit 8d06bc1751)
Netgear EAX12, EAX11v2, EAX15v2 are wall-plug 802.11ax (Wi-Fi 6)
extenders that share the SoC, WiFi chip, and image format with the
WAX202.
Specifications:
* MT7621, 256 MiB RAM, 128 MiB NAND
* MT7915: 2.4/5 GHz 2x2 802.11ax (DBDC)
* Ethernet: 1 port 10/100/1000
* UART: 115200 baud (labeled on board)
All LEDs and buttons appear to work without state_default.
Installation:
* Flash the factory image through the stock web interface, or TFTP to
the bootloader. NMRP can be used to TFTP without opening the case.
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References in GPL source:
https://www.downloads.netgear.com/files/GPL/EAX12_EAX11v2_EAX15v2_GPL_V1.0.3.34_src.tar.gz
* target/linux/ramips/dts/mt7621-rfb-ax-nand.dts
DTS file for this device.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
(cherry picked from commit 32ea8a9a7e)
