Ensure the MAC address for all NanoPi R4S boards is assigned unique for
each board.
FriendlyElec ship two versions of the R4S: The standard as well as the
enterprise edition with only the enterprise edition including the EEPROM
chip that stores the unique MAC address.
In order to assign both board types unique MAC addresses, fall back on
the same method used for the NanoPi R2S in case the EEPROM chip is not
present by generating the board MAC from the SD card CID.
[0] https://wiki.friendlyelec.com/wiki/index.php/NanoPi_R4S#Differences_Between_R4S_Standard_Version_.26_R4S_Enterprise_Version
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit b5675f500d)
On the NanoPI R4S it takes an average of 3..5 seconds for the network devices
to appear in '/proc/interrupts'.
Wait up to 10 seconds to ensure that the distribution of the interrupts
really happens.
Signed-off-by: Ronny Kotzschmar <ro.ok@me.com>
(cherry picked from commit 9b00e97956)
This enables armv8 crypto extensions version of AES, GHASH, and CRC T10
algorithms in the kernel.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit eef8fbec8f)
This board is a fork of OrangePi R1 Plus, with native NIC changed.
Hardware
--------
RockChip RK3328 ARM64 (4 cores)
1GB DDR4 RAM
2x 1000 Base-T
3 LEDs (LAN / WAN / SYS)
1 Button (Reset)
Micro-SD slot
USB 2.0 Port
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card using
dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 9d64b55c2e)
On the NanoPI R4S it takes an average of 3..5 seconds for the network devices
to appear in '/proc/interrupts'.
Wait up to 10 seconds to ensure that the distribution of the interrupts
really happens.
Signed-off-by: Ronny Kotzschmar <ro.ok@me.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit fd65ce6f32)
This board is a fork of NanoPi R2S, with the native NIC changed.
Hardware
--------
RockChip RK3328 ARM64 (4 cores)
1GB DDR4 RAM
2x 1000 Base-T
3 LEDs (LAN / WAN / SYS)
1 Button (Reset)
Micro-SD slot
USB 2.0 Port
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card using
dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
NanoPi R4S has a unique MAC address for the ethernet on board. As the
PCIe NIC doesn't have, just reuse this MAC and flipp the LA bit for it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 99adbe5ffd)
Move some disabled symbols found in armvirt target to generic.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
(cherry picked from commit 12e942b1fd)
Instead of deactivating this in every target config, deactivate it once
in the generic kernel config. I was asked for this config option in a
x86 64 build in OpenWrt 21.02.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 7d6553c72e)
This reverts commit 4126a5f695.
We found some issues with the usb3 inno driver, however it's good enough
to use generic usb3 driver for R2S, so revert it here and wait for fixes.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(backported from 44cbe50f17)
Referred to:
- a0e009a73e
- fcd9629c05
Signed-off-by: AmadeusGhost <amadeus@immortalwrt.org>
[separated new files from patches]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The NanoPi R2S does not have a board specific MAC address written inside
e.g. an EEPROM, hence why it is randomly generated on first boot.
The issue with that however is the lack of a driver for the PRNG.
It often results to the same MAC address used on multiple boards by
default, as urngd is not active at this early stage resulting in low
available entropy.
There is however a semi-unique identifier available to us, which is the
CID of the used SD card. It is unique to each SD card, hence we can use
it to generate the MAC address used for LAN and WAN.
Signed-off-by: David Bauer <mail@david-bauer.net>
The heartbeat trigger is used by luci-mod-system, which is installed
as a part of the standard luci package set. It seems the LED trigger
will be required quite often, so let's enable it by default.
This increases uncompressed kernel size by about 100 bytes on ath79/generic.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
When compiling with CONFIG_ALL_KMODS enabled, compilation might stall
due to unset rockchip-specific config symbols. Disable these to avoid
stalling this step.
Signed-off-by: David Bauer <mail@david-bauer.net>
Otherwise the missing symbol is added to target config for every kernel
config refresh.
While at it, remove the disabled symbol from target configs.
Fixes: 4943bc5cff ("kernel: only strip proc for small flash devices")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Remove MDIO and I2C bitbangig support from the kernel.
These functionalities are currently not used by any board in the target.
Signed-off-by: David Bauer <mail@david-bauer.net>
Extended attributes are required for overlayfs and have hence been long
ago enabled for jffs2, but should be enabled unconditionally for all
other filesystems which may potentially serve as overlayfs' upper
directory. Previously it was inconsistently added in multiple targets.
Add symbols to generic kernel config and remove all *_XATTR symbols
from target configs.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[keep things as they are for squashfs, improve commit message]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The NanoPi R2S features a Realtek Gigabit Ethernet PHY. Enable the
Realtek specific PHY driver to correctly configure internal delays.
Signed-off-by: David Bauer <mail@david-bauer.net>
The NanoPi R2S features a Realtek Gigabit Ethernet PHY. Enable the
Realtek specific PHY driver to correctly configure internal delays.
Signed-off-by: David Bauer <mail@david-bauer.net>
It is deactivated everywhere, just set this in the generic config.
Acked-by: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
