Hardware spec:
- Rockchip RK3568 Quad-core ARM Cortex-A55 CPU 2GHz
- GPU Mali-G52 1-Core-2EE OpenGL ES3.2 Vu1kn 1.1 OpenCL 2.0
- Memory2G DDR3 SDRAM (option 4G)
- Storage Onboard 16GB eMMC Flash, Micro SD-Card slot, SATA 3.0 Port,SPI flash
- Network 5 x 10/100/1000 Mbit/s Ethernet MT7531
- Display 1 HDMI port, 2 DSI interface(1 DSI can change to LVDS by software)
- Camera 1 CSI camera interface
- Audio Output HDMI & I2S & Speaker & Headphone
- USB port USB 3.0 PORT (x2), micro USB OTG (x1)
- PCIE 1 mini pcie interface & 1 M.2 key-e interface
- Remote IR Receiver (x1)
- GPIO 40 Pin Header : GPIO (x28) and Power (+5V, +3.3V and GND).
- Switches Reset button, Power button, U-boot button
- LED Power Status
- Power Source 12 volt 2A via DC Power
Installation:
Uncompress the OpenWrt sysupgrade and write image to the SD card using dd (dd if=*.img of=/*)
Boot from the SD card
1-hold down the MaskRom button
2-Connect DC power
3-Wait 5 seconds, release the button.
eMMC Installation:
1-Uncompress the OpenWrt sysupgrade image
2-fash to eMMC
dd if=openwrt-rockchip-armv8-sinovoip_bpi-r2-pro-squashfs-sysupgrade.img of=/dev/mmcblk1
sync
3-remove SD card
reboot
Signed-off-by: Antonio Flores <antflores627@gmail.com>
ttyS2 is the default console used for all rockchip boards.
The redundant 'console=tty1' parameter now breaks the console due to
recent procd update.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
We have hardware IOMMU support and this is totally unnecessary.
The given value is also unreasonable, it's too small and causes
kernel panic in some cases:
[ 5706.856473] sdhci-dwcmshc fe310000.mmc: swiotlb buffer is full (sz: 28672 bytes), total 512 (slots), used 498 (slots)
[ 5706.864451] sdhci-dwcmshc fe310000.mmc: swiotlb buffer is full (sz: 65536 bytes), total 512 (slots), used 464 (slots)
This parameter seems to be added by mistake, so remove it.
Fixes: e35c7ab51f ("rockchip: merge bootscript")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
We have hardware IOMMU support and this is totally unnecessary.
The given value is also unreasonable, it's too small and causes
kernel panic in some cases:
[ 5706.856473] sdhci-dwcmshc fe310000.mmc: swiotlb buffer is full (sz: 28672 bytes), total 512 (slots), used 498 (slots)
[ 5706.864451] sdhci-dwcmshc fe310000.mmc: swiotlb buffer is full (sz: 65536 bytes), total 512 (slots), used 464 (slots)
This parameter seems to be added by mistake, so remove it.
Fixes: 058bdf0396 ("rockchip: lzma compression for kernel")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Radxa E25 is a network application carrier board for the Radxa CM3
Industrial (CM3I) SoM, which is based on the Rockchip RK3568 SoC.
It has the following features:
- MicroSD card socket, on board eMMC flash
- 2x 2.5GbE Realtek RTL8125B Ethernet transceiver
- 1x USB Type-C port (Power and Serial console)
- 1x USB 3.0 OTG port
- mini PCIe socket (USB or PCIe)
- ngff PCIe socket (USB or SATA)
- 1x User LED and 16x RGB LEDs
- 26-pin expansion header
Installation:
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
Hardware
--------
RockChip RK3568 ARM64 (4 cores)
RGB LED
1/2/4/8GB LPDDR4 RAM
2x 2500 Base-T
2/16/32/64/128GB eMMC on-board
M.2 Slot
miniPCIe Slot
Micro-SD Slot
USB 3.0 Port
Type-C PD Power
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware
--------
RockChip RK3568 ARM64 (4 cores)
2/4/8GB LPDDR4 RAM
1000 Base-T
eMMC on-board
M.2 Slot
Micro-SD Slot
HDMI Port
3.5mm Audio Jack
2x USB 3.0 Port
2x USB 2.0 Port
Type-C PD Power
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware
--------
RockChip RK3568 ARM64 (4 cores)
2GB or 4GB LPDDR4 RAM
2x 1000 Base-T
QCA1023 Wi-Fi 5 / Bluetooth
16GB or 64GB eMMC on-board
2x M.2 Slot (B+E Key)
Micro-SD Slot
HDMI Port
USB 3.0 Port
7000 mAh Battery
Type-C Power
Note
----
The sdio card QCA1023 is not supported for now due to broken
ath10k-sdio driver.
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
In official OpenWrt we use kmod-r8169 driver provided by upstream kernel
instead of kmod-r8168 driver from Realtek.
Fixes: afca1236f3 ("rockchip: add NanoPi R4S Enterprise Edition build")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware
--------
RockChip RK3566 ARM64 (4 cores)
- up to 8GB LPDDR4X
- 1x HDMI,
- 2x MIPI DSI
- 2x MIPI CSI2
- 1x eDP
- 1x PCIe card
- 2x SATA
- 2x USB 2.0 Host
- 1x USB 3.0
- 1x USB 2.0 OTG
- 10/100/1000 Base-T
- microSD slot
- 40-pin GPIO expansion header
- 12V DC
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Reviewed-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
FriendlyElec renamed the NanoPi R4S board with EEPROM (mac address)
to "enterprise" edition, and it was added as a "new" board in upstream
kernel.
This patch switched to use that upstreamed dts and removed local
EEPROM patch.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The NanoPi R2C Plus is a small variant of NanoPi R2C with a on-board
eMMC flash (8G) included.
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Booting from non-MMC devices on Rockchip targets without this
change results in a boot failure:
Model: FriendlyElec NanoPi R5S
Net: eth0: ethernet@fe2a0000
Hit any key to stop autoboot: 0
** Booting bootflow 'nvme#0.blk#1.bootdev.part_1' with script
** No partition table - mmc 0 **
** No partition table - mmc 0 **
Couldn't find partition mmc 0:1
Can't set block device
Wrong Image Type for bootm command
ERROR -91: Protocol wrong type for socket: can't get kernel image!
Boot failed (err=1)
This change fixes the default boot script for Rockchip targets to
support booting from non-MMC devices such as NVMe or USB drives.
Some targets with only a boot rom (e.g. NanoPi R5S) may require u-boot
to be installed on the eMMC or a MicroSD card in order to boot from
non-MMC devices.
Fixes: #14420
Reviewed-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: Justin Klaassen <justin@tidylabs.app>
It's applicable for all devices so move it to default to reduce
redudant code. Addtionally introduce a new variable `BOOT_SCRIPT`
to allow custom boot script (if necessary).
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
This adds support for Radxa ROCK Pi E, rockchip rk3328 board.
Specification:
- CPU: Rockchip RK3328 64-bit Quad-core
- RAM: DDR3 256MB ~ 2GB
- Network:
1 x 10/100/1000M Ethernet
1 x 10/100M Ethernet
- Storage:
1 x MicroSD Slot
1 x eMMC Module Slot
- USB Host/OTG:
1 x USB3.0 Type A HOST
1 x USB2.0 HOST (40-pin pin-header)
- Wireless
RTL8723DU/RTL8821CU
- Debug Serial:
1500000 baud at UART2 ( 40-pin pin-header)
- Power Supply:
Type-C 5V
Optionally PoE
Installation:
- Write image to SD Card or EMMC with dd
- Boot ROCK Pi E from the SD Card
Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
This add support for PINE64 ROCK64, rockchip rk3328 board.
Specifications:
4 x ARM Cortex A53 cores @ 1.5 GHz
ARM Mali 450 MP2 GPU
LPDDR3 RAM (up to 4GB)
Gigabit Ethernet
Micro SD Slot
eMMC module slot
SPI Flash 128Mbit
4K digital video out
2x USB 2.0 Host
1x USB 3.0 Host
PI-2 bus
PI-P5+ bus
IR R/X port
Real Time Clock (RTC) port
Power Over Ethernet (POE) (when using optional HAT module)
A/V jack
Power, Reset and Recovery buttons
3.5mm barrel power (5V 3A) port
To install write image to the sd using dd (dd if=*.img of=/*)
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Hardware
--------
RockChip RK3588 ARM64 (8 cores)
4/8/16GB LPDDR4X RAM
2x 2500 Base-T (PCIe, rtl8125b)
2 LEDs (POWER / WAN)
32/64/256GB eMMC on-board
Micro-SD Slot
USB 2.0 Port
Headphone
USB 3.0
USB PD 2.0
M.2 M-Key
M.2 E-Key
DC Jack 12V
Installation
------------
Uncompress the ImmortalWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware
--------
RockChip RK3399 ARM64 (6 cores)
4GB LPDDR3 RAM
1x 1000 Base-T
1 GPIO LED (status)
HDMI 2.0
3.5mm TRRS AV jack
Micro-SD slot
16GB eMMC
1x USB 3.0 Port
2x USB 2.0 Port
1x USB Type-C Port
1x M.2 PCI-E Port
AP6356S (BCM4356) SDIO WiFi & Bluetooth adapter
--------
Note: AP6356S is not supported yet due to the lack of firmware and NVRAM
Signed-off-by: Lu jicong <jiconglu58@gmail.com>
Hardware
--------
RockChip RK3399 ARM64 (6 cores)
4GB LPDDR3 RAM
1x 1000 Base-T
1 GPIO LED (status)
HDMI 2.0
3.5mm TRRS AV jack
Micro-SD slot
16GB eMMC
1x USB 3.0 Port
2x USB 2.0 Port
1x USB Type-C Port
1x M.2 PCI-E Port
AP6356S (BCM4356) SDIO WiFi & Bluetooth adapter
--------
Note: AP6356S is not supported yet due to the lack of firmware and NVRAM
Signed-off-by: Lu jicong <jiconglu58@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware
--------
RockChip RK3568 ARM64 (4 cores)
2/4/8GB LPDDR4 RAM
2x 1000 Base-T
Bluetooth 5.0
Dual-band Wi-Fi6
2 LEDs (POWER / USER)
32/64/128GB eMMC on-board
Micro-SD Slot
M.2 Slot
SATA 3.0 interfaces
HDMI 2.0
Headphone
2x USB 2.0 Port
USB 3.0 Port
DC 12V
Installation
------------
Uncompress the ImmortalWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware
--------
RockChip RK3588 ARM64 (8 cores)
4/8/16GB LPDDR4X RAM
2500 Base-T (PCIe, rtl8125b)
RGB LED
8/16/32/64/128GB eMMC on-board
Micro-SD Slot
USB 2.0 Port
Headphone
USB PD 2.0 12/15/20V
Install
--------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The OrangePi R1 Plus LTS is a minor variant of OrangePi R1 Plus with
the on-board NIC chip changed from rtl8211e to yt8531c, and otherwise
identical to OrangePi R1 Plus.
Tested-by: Volkan Yetik <no3iverson@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Orange Pi R1 Plus is a Rockchip RK3328 based SBC by Xunlong.
This device is similar to the NanoPi R2S, and has a 16MB
SPI NOR (mx25l12805d). The reset button is changed to
directly reset the power supply, another detail is that
both network ports have independent MAC addresses.
Note: booting from SPI is currently unsupported, you have to install
the image on a SD card.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
This board was designed as a clone of NanoPi R4S. However, it didn't
follow the spec and changed the power-supply system massively, and
because of it there's no way to soft reset this board currently.
For reboot, you must cut off the power and reengage it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The NanoPi R2C is a minor variant of NanoPi R2S with the on-board NIC
chip changed from rtl8211e to yt8521s, and otherwise identical to R2S.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
