correct oversight on setting regulatory country and mac address of wireless configuration
change method of retrieving mac address
The MAC address for eth0 is rad out of the devinfo partition in some
other initial configuration script already.
Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
correct device CC oversight
Set the initial wifi configuration like for the other similar Linksys
devices.
Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
This commit contains patches for PCI aardvark driver and relevant DTS
changes for Turris MOX and EspressoBin backported from mainline kernel.
It fixes support for old ATF, various wifi cards, mainly Compex WLE900VX.
Signed-off-by: Pali Rohár <pali@kernel.org>
Usage of current R1 ISA is inconsistent with the MIPS32 subtarget, little
used and has limited utility for testing.
Many distros target a minimum R2 ISA. Debian MIPS 32-bit/64-bit ports all
use MIPS R2 ISA since Stretch, for example. Fedora's MIPS arch also targets
the R2 ISA for 32-bit/64-bit.
Widely used MIPS64 platforms like Octeon are based on the MIPS R2 ISA or
later, and benefit from having a compatible test platform in OpenWRT.
While Linux does support MIPS64 R1 targets, its usefulness for development
and testing is limited. As an example, the modern Linux eBPF JIT requires
a MIPS R2 ISA or later.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
[Refresh config and fix README]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Similar to how it was already done for other filesystems' *_FS_XATTR
kernel config symbols, also move CONFIG_F2FS_FS_XATTR=y and
CONFIG_F2FS_STAT_FS=y to target/linux/generic.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Since "sda-gpios" and "scl-gpios" are only available since kernel 4.19,
a few devices have redundantly defined "gpios" to also support older
kernels. Since we have nothing older than 4.19 now, we can remove
the redundant definitions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This fixes a regression after a kernel change in 5.4.69 [1] that
led to build failure on oxnas/ox820:
drivers/ata/sata_oxnas.c:2238:13: error: initialization of
'enum ata_completion_errors (*)(struct ata_queued_cmd *)'
from incompatible pointer type
'void (*)(struct ata_queued_cmd *)' [-Werror=incompatible-pointer-types]
.qc_prep = sata_oxnas_qc_prep,
^~~~~~~~~~~~~~~~~~
drivers/ata/sata_oxnas.c:2238:13: note:
(near initialization for 'sata_oxnas_ops.qc_prep')
Our local driver is changed the same way as prototyped in the
kernel patch, i.e. return type is changed and AC_ERR_OK return
value is added.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=e11c83520cd04b813cd1748ee2a8f2c620e5f7e3
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Upstream provides DTS(I) files for IPQ4019/AP-DK04.1, but we overwrite
them with local versions so far.
Remove the local files and use patches to be closer to upstream.
We already do the same for IPQ40xx/AP-DK01.1-C1.
Technically, this changes the compatible from "qcom,ipq4019" to
"qcom,ipq4019-dk04.1-c1", but it has never been implemented correctly
beforehand anyway.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Extended attributes are required for overlayfs and have hence been long
ago enabled for jffs2, but should be enabled unconditionally for all
other filesystems which may potentially serve as overlayfs' upper
directory. Previously it was inconsistently added in multiple targets.
Add symbols to generic kernel config and remove all *_XATTR symbols
from target configs.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[keep things as they are for squashfs, improve commit message]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use the full model name for this device to make it easier to
recognize for the users and in order to make it consistent with
the other devices.
While at it, fix sorting in 03_gpio_switches.
Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
[commit message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This disable eee for mt7530 ports, it causes the link down/up
issue, which happens when connecting to 100Mbit switch
Fixes: FS#1449
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
This commit fixes the name for the GMAC clock to gmac_clkin, as this is
the name of the clock provided by the rk3328-clk driver.
Without this commit, the GMAC will not work in TX direction.
Suggested-by: Tobias Waldvogel <tobias.waldvogel@gmail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Since we have a v2.1 (EU) with different partitioning now, rename
the v2.0 to make the difference visible to the user more directly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for the TP-Link TL-WPA8630P (EU) in its v2.1
version. The only unique aspect for the firmware compared to v2
layout is the partition layout.
Note that while the EU version has different partitioning for
v2.0 and v2.1, the v2.1 (AU) is supported by the v2-int image.
If you plan to use this device, make sure you have a look at
the Wiki page to check whether the device is supported and
which image needs to be taken.
Specifications
--------------
- QCA9563 750MHz, 2.4GHz WiFi
- QCA9888 5GHz WiFi
- 8MiB SPI Flash
- 128MiB RAM
- 3 GBit Ports (QCA8337)
- PLC (QCA7550)
Installation
------------
Installation is possible from the OEM web interface. Make sure to
install the latest OEM firmware first, so that the PLC firmware is
at the latest version. However, please also check the Wiki page
for hints according to altered partitioning between OEM firmware
revisions.
Notes
-----
The OEM firmware has 0x620000 to 0x680000 unassigned, so we leave
this empty as well. It is complicated enough already ...
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
[improve partitions, use v2 DTSI, add entry in 02_network, rewrite
and extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The D-Link DIR-645 currently uses an incorrect logic level for its
buttons.
Correct them in order to prevent unintentional activation of failsafe
mode.
Reported-by: Perry Melange <isprotejesvalkata@gmail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds basic support for Radxa Rock Pi 4
Specification:
- RAM: 1 GB/ 2 GB/4 GB LPDDR4
- SoC: Rockchip RK3399
- CPU: 64bit hexa core processor
Dual Cortex-A72, freqency 1.8Ghz
with quad Cortex-A53, frequency 1.4Ghz
- USB: USB 3.0 OTG x1
hardware switch for host/device switch, upper one
USB 3.0 HOST x1
dedicated USB3.0 channel, lower one
USB 2.0 HOST x2
- Ethernet: 1x GbE
- Storage: eMMC module
uSD card
M.2 SSD
- Wireless: 802.11 ac wifi
Bluetooth 5.0
currently not supported
firmware Installation
======================
gzip -d xxx.img.gz, then dd the .img to SD/eMMC
======================
Device Tested: ROCK PI 4 Model B v1.3
Signed-off-by: Marty Jones <mj8263788@gmail.com>
This patch intruduce SATA support for layerscape devices.
Target specific package with ahci_qoriq driver was added
to local modules.mk.
Kmod package was added to default packages for devices with
SATA interface.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch adds kmod-hwmon-ina2xx kmod-hwmon-lm90 for boards,
which have it installed.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Yangbo Lu <yangbo.lu@nxp.com>
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.
In lantiq, we therefore requested to have in the DTS files so far,
and omit it in the DTSI files. However, essentially the syntax of
the parent SoC-based DTSI files already determines the DTS
version, so putting it into the DTS files is just a useless repetition.
Consequently, this patch puts the dts-v1 statement into the top-level
SoC-based DTSI files, and removes all other occurences.
Since the dts-v1 statement needs to be before any other definitions,
this also moves the includes accordingly where necessary.
Changes are applied to files-5.4 only, files-4.19 remains untouched.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The NanoPi R2S features a Realtek Gigabit Ethernet PHY. Enable the
Realtek specific PHY driver to correctly configure internal delays.
Signed-off-by: David Bauer <mail@david-bauer.net>
Seemingly unneeded based on new upstream code so manually deleted:
platform/820-usb-0007-usb-dwc3-gadget-increase-timeout-value-for-send-ep-c.patch
Manually merged:
generic-hack/251-sound_kconfig.patch
All other modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Fix the PHY ID for the NanoPi R2S PHY compatible to match the used PHY.
The ID was wrong as I've accidentally picked the wrong upstream patch.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds the compatible property to the NanoPi R2S ethernet PHY node.
Otherwise, the PHY might not be probed, as the PHY ID reads all 0xff
when it is still in reset.
Signed-off-by: David Bauer <mail@david-bauer.net>
reg accesses on integrated ar8229 sometimes fails. As a result, phy read
got incorrect port status and wan link goes down and up mysteriously.
After comparing ar8216 with the old driver, these local_irq_save/restore
calls are the only meaningful differences I could find and it does fix
the issue.
The same changes were added in svn r26856 by Gabor Juhos:
ar71xx: ag71xx: make switch register access atomic
As I can't find the underlying problem either, this hack is broght
back to fix the unstable link issue.
This hack is only suitable for ath79 mdio and may easily break the
driver on other platform. Limit it to ath79-only as a target patch.
Fixes: FS#2216
Fixes: FS#3226
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This commit add support for the yyets_le router.
Hardware Highlights:
SoC: Qualcomm IPQ4019 717 MHz
RAM: 512M NT5CC256M16ER-EK
Flash: 32M SPI NOR MX25L25635F
WIFI1: 2.4 GHz 2T2R integrated
WIFI2: 5 GHz 2T2R integrated
Ethernet: Qualcomm QCA8075 (4x LAN, 1x WAN)
USB: 1x 3.0
LEDS: power, wlan2g, wlan5g, usb
Button: Reset
Installation:
Upload the firmware on the upgrade page of the stcok, and this will take a few minutes.
This commit also supports the addition of a 128M nand flash version,
just use the P&W R619AC's opboot to overwrite the original uboot.
Signed-off-by: AmadeusGhost <amadeus@jmu.edu.cn>
All modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x, ath79/generic, bcm72xx/bcm2711
Run-tested: ipq806x (R7800)
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
