Since "sda-gpios" and "scl-gpios" are only available since kernel 4.19,
a few devices have redundantly defined "gpios" to also support older
kernels. Since we have nothing older than 4.19 now, we can remove
the redundant definitions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Use the full model name for this device to make it easier to
recognize for the users and in order to make it consistent with
the other devices.
While at it, fix sorting in 03_gpio_switches.
Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
[commit message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Since we have a v2.1 (EU) with different partitioning now, rename
the v2.0 to make the difference visible to the user more directly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for the TP-Link TL-WPA8630P (EU) in its v2.1
version. The only unique aspect for the firmware compared to v2
layout is the partition layout.
Note that while the EU version has different partitioning for
v2.0 and v2.1, the v2.1 (AU) is supported by the v2-int image.
If you plan to use this device, make sure you have a look at
the Wiki page to check whether the device is supported and
which image needs to be taken.
Specifications
--------------
- QCA9563 750MHz, 2.4GHz WiFi
- QCA9888 5GHz WiFi
- 8MiB SPI Flash
- 128MiB RAM
- 3 GBit Ports (QCA8337)
- PLC (QCA7550)
Installation
------------
Installation is possible from the OEM web interface. Make sure to
install the latest OEM firmware first, so that the PLC firmware is
at the latest version. However, please also check the Wiki page
for hints according to altered partitioning between OEM firmware
revisions.
Notes
-----
The OEM firmware has 0x620000 to 0x680000 unassigned, so we leave
this empty as well. It is complicated enough already ...
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
[improve partitions, use v2 DTSI, add entry in 02_network, rewrite
and extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
reg accesses on integrated ar8229 sometimes fails. As a result, phy read
got incorrect port status and wan link goes down and up mysteriously.
After comparing ar8216 with the old driver, these local_irq_save/restore
calls are the only meaningful differences I could find and it does fix
the issue.
The same changes were added in svn r26856 by Gabor Juhos:
ar71xx: ag71xx: make switch register access atomic
As I can't find the underlying problem either, this hack is broght
back to fix the unstable link issue.
This hack is only suitable for ath79 mdio and may easily break the
driver on other platform. Limit it to ath79-only as a target patch.
Fixes: FS#2216
Fixes: FS#3226
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Hak5 WiFi Pineapple NANO is an "USB dongle" device dedicated for Wi-Fi
pentesters. This device is based on Atheros AR9331 and AR9271. Support
for it was first introduced in 950b278c81 (ar71xx). FCC ID: 2AB87-NANO.
Specifications:
- Atheros AR9331
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR1)
- 16 MB of flash (SPI NOR)
- 1T1R 2.4 GHz Wi-Fi (AR9331)
- 1T1R 2.4 GHz Wi-Fi (AR9271L), with ext. PA and LNA (Qorvo RFFM4203)
- 2x RP-SMA antenna connectors
- 1x USB 2.0 to 10/100 Ethernet bridge (ASIX AX88772A)
- integrated 4-port USB 2.0 HUB: Alcor Micro AU6259:
- 1x USB 2.0
- 1x microSD card reader (Genesys Logic GL834L)
- Atheros AR9271L
- 1x LED, 1x button
- UART (4-pin, 2 mm pitch) header on PCB
- USB 2.0 Type-A plug for power and AX88772A
Flash instruction:
You can use sysupgrade image directly in vendor firmware which is based
on OpenWrt/LEDE.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Hak5 Packet Squirrel is a pocket-sized device dedicated for pentesters
(MITM attacks). This device is based on Atheros AR9331 but it lacks
WiFi. Support for it was first introduced in 950b278c81 (ar71xx).
Specifications:
- Atheros AR9331
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2x RJ45 10/100 Mbps Ethernet (AR9331)
- 1x USB 2.0
- 1x RGB LED, 1x button, 1x 4-way mechanical switch
- 1x Micro USB Type-B for main power input
Flash instruction:
You can use sysupgrade image directly in vendor firmware which is based
on OpenWrt/LEDE.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Hak5 LAN Turtle is an "USB Ethernet Adapter" shaped device dedicated for
sysadmins and pentesters. This device is based on Atheros AR9331 but it
lacks WiFi. Support for it was first introduced in 950b278c81 (ar71xx).
Two different versions of this device exist and it's up to the user to
install required drivers (generic image supports only common features):
- LAN Turtle 3G with Quectel UG96 3G modem
- LAN Turtle SD with microSD card reader (Alcorlink AU6435R)
Specifications:
- Atheros AR9331
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 1x RJ45 10/100 Mbps Ethernet (AR9331)
- 1x USB 2.0 to 10/100 Ethernet bridge (Realtek RTL8152B)
- 2x LED (power, system), 1x button (inside, on the PCB)
- USB 2.0 Type-A plug for power and RTL8152B
Flash instruction:
You can use sysupgrade image directly in vendor firmware which is based
on OpenWrt/LEDE.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network N5Q is a successor of previous model, the N5 (outdoor
CPE/AP, based on Atheros AR7240 + AR9280). New version is based on
Atheros AR9344.
Support for this device was first introduced in 4b0eebe9df (ar71xx
target) but users are advised to migrate from ar71xx target without
preserving settings as ath79 support includes some changes in network
and LED default configuration. They were aligned with vendor firmware
and recently added N2Q model (both Ethernet ports as LAN, labelled as
LAN1 and LAN2).
Specifications:
- Atheros AR9344
- 550/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 5 GHz Wi-Fi, with ext. PA (RFPA5542) and LNA, up to 27 dBm
- 2x IPEX/U.FL or MMCX antenna connectors (for PCBA version)
- 8x LED (7 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, enabled by default)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART (4-pin, 2.54 mm pitch) header on PCB
- LEDs (2x 5-pin, 2.54 mm pitch) header on PCB
Flash instruction:
You can use sysupgrade image directly in vendor firmware which is based
on OpenWrt/LEDE. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network N2Q is an outdoor N300 AP/CPE based on Qualcomm/Atheros
QCA9531 v2. This model is a successor of the old N2 which was based
on Atheros AR7240. FCC ID: 2AB8795311.
Specifications:
- Qualcomm/Atheros QCA9531 v2
- 650/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2T2R 2.4 GHz Wi-Fi with ext. PA (Skyworks SE2623L) and LNA
- 2x 10/100 Mbps Ethernet with passive PoE input in one port (24 V)
- PoE pass through in second port (controlled by GPIO)
- support for optional 802.3af/at PoE module
- 1x mini PCIe slot (PCIe bus, extra 4.2 V for high power cards)
- 2x IPEX/U.FL connectors on PCB
- 1x USB 2.0 mini Type-B (power controlled by GPIO)
- 8x LED (7 of them are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, enabled by default)
- UART (4-pin, 2.54 mm pitch) header on PCB
- LEDs (2x 5-pin, 2.54 mm pitch) header on PCB
Flash instruction:
You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network R36A is a successor of the previous model, the R36 (Ralink
RT3050F based). New version is based on Qualcomm/Atheros QCA9531 v2, FCC
ID: 2AB879531.
Support for this device was first introduced in af8f0629df (ar71xx
target). When updating from previous release (and/or ar71xx target),
user should only adjust the WAN LED trigger type (netdev in ar71xx,
switch port in ath79).
Specifications:
- Qualcomm/Atheros QCA9531 v2
- 650/400/200 MHz (CPU/DDR/AHB)
- 128 MB (R36AH/-U2) or 64 MB (R36A) of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2x 10/100 Mbps Ethernet
- Passive PoE input support (12~36 V) in RJ45 near DC jack
- 2T2R 2.4 GHz Wi-Fi with Qorvo RFFM8228P FEM
- 2x IPEX/U.FL connectors on PCB
- 1x USB 2.0 Type-A
- 1x USB 2.0 mini Type-B in R36AH-U2 version
- USB power is controlled by GPIO
- 6/7x LED (5/6 of them are driven by GPIO)
- 2x button (reset, wifi/wps)
- external h/w watchdog (EM6324QYSP5B, enabled by default)
- DC jack with lock, for main power input (12 V)
- UART (4-pin, 2.54 mm pitch) header on PCB
Optional/additional features in R36A series (R36A was the first model):
- for R36AH: USB 2.0 hub*
- for R36AH-U2: USB 2.0 hub*, 1x USB 2.0 mini Type-B, one more LED
*) there are at least three different USB 2.0 hub in R36AH/-U2 variants:
- Terminus-Tech FE 1.1
- Genesys Logic GL852G
- Genesys Logic GL850G (used in latests revision)
Flash instruction:
You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Samsung WAM250 is a dual-band (selectable, not simultaneous) wireless
hub, dedicated for Samsung Shape Wireless Audio System. The device is
based on Atheros AR9344 (FCC ID: A3LWAM250). Support for this device
was first introduced in e58e49bdbe (ar71xx target).
Specifications:
- Atheros AR9344
- 560/450/225 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2x 10/100 Mbps Ethernet
- 2T2R 2.4/5 GHz Wi-Fi, with ext. PA (SE2598L, SE5003L) and LNA
- 1x USB 2.0
- 4x LED (all are driven by GPIO)
- 2x button (reset, wps/speaker add)
- DC jack for main power input (14 V)
- UART header on PCB (J4, RX: 3, TX: 5)
Flash instruction:
This device uses dual-image (switched between upgrades) with a common
jffs2 config partition. Fortunately, there is a way to disable this mode
so that more flash space can be used by OpenWrt image.
You can easily access this device over telnet, using root/root
credentials (the same also work for serial console access).
1. Make sure that your device uses second (bootpart=2) image using
command: "fw_printenv bootpart".
2. If your device uses first image (bootpart=1), perform upgrade to the
latest vendor firmware (after the update, device should boot from
second partition) using web gui (default login: admin/1234567890).
3. Rename "sysupgrade" image to "firmware.bin", download it (you can use
wget, tftp or ftpget) to "/tmp" and issue below commands:
mtd_debug erase /dev/mtd3 0 $(wc -c /tmp/firmware.bin | awk -F' ' '{print $1}')
mtd_debug write /dev/mtd3 0 $(wc -c /tmp/firmware.bin)
fw_setenv bootpart
fw_setenv bootcmd "bootm 0x9f070000"
reboot
Revert to vendor firmware instruction:
1. Download vendor firmware to "/tmp" device and issue below commands:
fw_setenv bootpart 1
sysupgrade -n -F SS_BHUB_v2.2.05.bin
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Wallys DR531 is based on Qualcomm Atheros QCA9531 v2. Support for this
device was first introduced in e767980eb8 (ar71xx target).
Specifications:
- Qualcomm/Atheros QCA9531 v2
- 550/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR2)
- 8 MB of flash (SPI NOR)
- 2T2R 2.4 GHz Wi-Fi, with external PA (SE2576L), up to 30 dBm
- 2x MMCX connectors (optional IPEX/U.FL)
- mini PCIe connector (PCIe/USB buses and mini SIM slot)
- 7x LED, 1x button, 1x optional buzzer
- UART, JTAG and LED headers on PCB
Flash instruction (do it under U-Boot, using UART):
tftpb 0x80060000 openwrt-ath79-...-dr531-squashfs-sysupgrade.bin
erase 0x9f050000 +$filesize
cp.b $fileaddr 0x9f050000 $filesize
setenv bootcmd "bootm 0x9f050000"
saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The AP121FE is a slightly modified version of already supported AP121F
model (added to ar71xx in 0c6165d21a and to ath79 in 334bbc5198).
The differences in compare to AP121F:
- no micro SD card reader
- USB data lines are included in Type-A plug
- USB bus switched to device/peripheral mode (permanently, in bootstrap)
Other than that, specifications are the same:
- Atheros AR9331
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR1)
- 16 MB of flash (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz Wi-Fi, up to 15 dBm
- 1x IPEX/U.FL connector, internal PCB antenna
- 3x LED, 1x button, 1x switch
- 4-pin UART header on PCB (2 mm pitch)
- USB 2.0 Type-A plug (power and data)
Flash instruction (under U-Boot web recovery mode):
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with RJ45 port, press the reset button, power up device,
wait for first blink of all LEDs (indicates network setup), then keep
button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The order of function and color in the labels in inverted for the
LAN LEDs. Fix it.
Fixes: 915966d861 ("ath79: Port PowerCloud Systems CAP324 support")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The LED color was missing in 01_leds.
Fixes: 745dee11ac ("ath79: add support for WD My Net Wi-Fi Range
Extender")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.
In ath79, we therefore requested to have in the DTS files so far,
and omit it in the DTSI files. However, essentially the syntax of
the parent ath79.dtsi file already determines the DTS version, so
putting it into the DTS files is just a useless repetition.
Consequently, this patch puts the dts-v1 statement into the parent
ath79.dtsi, which is (indirectly) included by all DTS files. All
other occurences are removed.
Since the dts-v1 statement needs to be before any other definitions,
this also moves the includes to make sure the ath79.dtsi or its
descendants are always included first.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ath79.dtsi uses ATH79_CLK_MDIO, so the include
<dt-bindings/clock/ath79-clk.h>
needs to be moved there.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
SPDX moved from GPL-2.0 to GPL-2.0-only and from GPL-2.0+ to
GPL-2.0-or-later. Reflect that in the SPDX license headers.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Move engenius_loader_okli image recipe in front of all Engenius
devices, so adding new device entries will not have them sorted
before the shared recipe.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The legacy ar71xx target is removed and multiple targets use DTS now, so
there is no need to point that out for ATH79 specifically.
Signed-off-by: Paul Spooren <mail@aparcar.org>
IMAGE_SIZE is widely used in many targets. Declare it in the default template to
clean up redundant code. This also prevents deriving IMAGE_SIZE unintentionally
from the previously defined device.
While at it, remove duplicate KERNEL_SIZE declaration.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This adds support for the Ubiquiti UniFi AP Pro to the ath79 target. The
device was previously supported on the now removed ar71xx target.
SoC Atheros AR9344
WiFi Atheros AR9344 & Atheros AR9280
ETH Atheros AR8327
RAM 128M DDR2
FLASH 16M SPI-NOR
Installation
------------
Follow the Ubiquiti TFTP recovery procedure for this device.
1. Hold down the reset button while connecting power for 10 seconds.
2. Transfer the factory image via TFTP to the AP (192.168.1.20)
3. Wait 2 minutes for the AP to write the firmware to flash. The device
will automatically reboot to OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
The tp-link safeloader devices typically contain a partition
"default-mac" which stores the MAC addresses. It is followed by other
partitions containing device info, like
{"default-mac", 0x610000, 0x00020},
{"pin", 0x610100, 0x00020},
{"product-info", 0x611100, 0x01000},
In DTS, we typically assign a 0x10000 sized partition for these,
which is mostly labelled "mac" or "info". In rarer cases, the
partitions have been enclosed in a larger "tplink" or "config"
partition.
However, when comparing different devices, the implementation appears
relatively arbitrary at the moment.
Thus, this PR aims at harmonizing these partitions by always using
the name "info" for the DTS partition containing "default-mac".
"info" is preferred over "mac" as we never just have "default-mac"
alone, but always some other device-info partitions as well.
While at it, this also establishes a similar partitioning for the
few devices where the "info" partitions are part of a bigger
unspecific "config" partition or similar.
Besides the harmonization itself, this also allows to merge a few
cases in 11-ath10k-caldata.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Router and Movie "keys" are actually switches for both devices
according to the manual. This has been properly implemented in ar71xx,
but overlooked when porting to ath79.
Fixes: 480bf28273 ("ath79: add support for Buffalo WZR-HP-AG300H")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The hardware of this device seems to be identical to WZR-HP-AG300H.
It was already implemented as a clone in ar71xx.
Specification:
- 680 MHz CPU (Qualcomm Atheros AR7161)
- 128 MiB RAM
- 32 MiB Flash
- WiFi 5 GHz a/n
- WiFi 2.4 GHz b/g/n
- 5x 1000Base-T Ethernet
- 1x USB 2.0
Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.11.1
- Go to “Administration” → “Firmware Upgrade”
- Upload the OpenWrt factory image
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link EAP225-Wall v2 is an AC1200 (802.11ac Wave-2) wall plate access
point. UART access and debricking require fine soldering.
The device was kindly provided for porting by Stijn Segers.
Device specifications:
* SoC: QCA9561 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR (GD25Q127CSIG)
* Wireless 2.4GHz (SoC): b/g/n, 2x2
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO
* Ethernet (SoC): 4× 100Mbps
* Eth0 (back): 802.3af/at PoE in
* Eth1, Eth2 (bottom)
* Eth3 (bottom): PoE out (can be toggled by GPIO)
* One status LED
* Two buttons (both work as failsafe)
* LED button, implemented as KEY_BRIGHTNESS_TOGGLE
* Reset button
Flashing instructions, requires recent firmware (tested on 1.20.0):
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface
Debricking:
* Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC)
* Bridge unpopulated resistors R162 (TXD) and R165 (RXD)
Do NOT bridge R164
* Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via sysupgrade or LuCI web interface
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From OEM ifconfig:
br0 Link encap:Ethernet HWaddr 50:...:04
eth0 Link encap:Ethernet HWaddr 50:...:04
wifi0 Link encap:UNSPEC HWaddr 50-...-04-...
wifi1 Link encap:UNSPEC HWaddr 50-...-05-...
Signed-off-by: Sander Vanheule <sander@svanheule.net>
[fix IMAGE_SIZE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The soft_config partition for these devices lays between 0xe000 and
0xf000 (as correctly detected by the RouterBoard platform driver),
before the bootloader2 partition which starts at 0x10000.
This commit correctly sorts the partitions, fixing the parsing error.
Fixes: FS#3314
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org>
The Buffalo devices in ath79 share their image generation code,
so let's create a shared Device definition for them.
Since most of them use BUFFALO_HWVER := 3, this is moved as
default to the shared definition as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Enabled the ELF firmware partition splitter 4.19 and 5.4 in preparation
for the TP-Link EAP245v3 device support.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
This is the same as loader-kernel since the KERNEL_CMDLINE
parameter has been removed in [1] and not used at all anyway.
Remove it.
[1] f77db1a590 ("ath79: cleanup image build code")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
The kernel has become too big again for the ar9344-based TP-Link
CPE/WBS devices which still have no firmware-partition splitter.
Current buildbots produce a kernel size of about 2469 kiB, while
the partition is only 2048 kiB (0x200000). Therefore, increase it
to 0x300000 to provide enough room for this and, hopefully, the
next kernel.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For many target we have added CONFIG_WATCHDOG_CORE=y to the target
config due to the following error:
Package kmod-hwmon-sch5627 is missing dependencies for the following
libraries:
watchdog.ko
However, actually the proper way appears to be setting the
dependency for the kmod-hwmon-sch5627 package, as the error message
demands.
Do this in this patch and remove the target config entries added
due to this issue.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
On Mikrotik SPI NOR devices, the firmware partition must be erased when
flashing from stock firmware, otherwise leftover bits (in particular a
kernel signature) can trigger a boot loop.
When booted from initramfs (the only way to install OpenWRT on these
devices), this patch unconditionally erases the firmware partition in
the do_upgrade() stage for all supported SPI NOR devices.
This is forward-ported from ed49d0876 and 20452a8db
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
The node needs to be terminated by a semicolon.
Fixes: 8484a764df ("ath79: ar724x: make sure builtin-switch is
enabled in DT")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
On ar7240/ar7241 the mdioX node with the builtin-switch is enabled
in the DTSI files, but the parent ethX node is left disabled. It
only gets enabled per device or device family, and has not been
enabled at all yet for the TP-Link WA devices with ar7240, making
the switch unavailable there.
This patch makes sure ð0/ð1 nodes are enabled together with
the &mdio0/&mdio1 nodes containing the builtin-switch.
For ar7240_tplink_tl-wa.dtsi, ð0 is properly hidden again via
compatible = "syscon", "simple-mfd";
This partially fixes FS#2887, however it seems dmesg still does
not show cable (dis)connect in dmesg for ar7240 TP-Link WA
devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
