Openwrt supports hundreds of devices. These newly added LED colors
and functions can help developers better describe LED indicators.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 6c41c585e3)
Specifications:
SoC: MediaTek MT7981B
RAM: 256MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 3 LAN (Gigabit)
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND
No. of Antennas: 6
Note: Upon opening the router, only 5 antennas were connected
to the mainboard.
Led Layout:
Power-Mesh-5gwifi-WAN-LAN3-LAN2-LAN1-2gWiFi
Buttons:
Reset-Mesh
Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware
B. Through TFTP
Standard installation via UART:
1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.
Signed-off-by: Ian Oderon <ianoderon@gmail.com>
(cherry picked from commit 4300bc6688)
Include XHCI USB drivers on the ZBT-Z8102AX router, the drivers are
required to be able to use the USB-connected M.2 slots for 4G/5G modems.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 507ad4f078)
The EnGenius EAP1300 and EAP1300EXT use identical boards and firmware
(as flashed) from the vendor.
As with the EAP1300, the EAP1300EXT requires a specific firmware version
to flash OpenWRT. Unfortunately, the required firmware is truncated on
the vendor's website.
A working file can be created as follows:
```
curl \
https://www.engeniustech.com/wp_firmware/eap1300-all-v3.5.3.5_c1.9.04.bin \
| perl -pe 's/\x09EAP1300_A/\x0cEAP1300EXT_A/' \
> eap1300ext-all-v3.5.3.5_c1.9.04.bin
```
The file should have sha256:
`58a1197a426139a12b03fd432334e677124cbe3384349bd7337f2ee71f1dcfd4`.
Please see commit 2b4ac79 for further
details.
The vendor firmware must be decrypted before it can be flashed from
OpenWRT. A tool able to do that is available from:
https://github.com/ryancdotorg/enfringement/blob/main/decrypt.py
Signed-off-by: Ryan Castellucci <code@ryanc.org>
(cherry picked from commit 85f6f88223)
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: W632GU6NB DDR3 256MB
Ethernet: 1x 2.5G + 4x 1G
WiFi1: MT7975N 2.4GHz 4T4R
WiFi2: MT7975PN 5GHz 4T4R
Button: Reset, WPS
Power: DC 12V 2A
Flash instructions:
1. Connect to the router using ssh or telnet,
username: useradmin, password is the web
login password of the router.
2. Use scp to upload bl31-uboot.fip and flash:
"mtd write xxx-preloader.bin spi0.0"
"mtd write xxx-bl31-uboot.fip FIP"
"mtd erase ubi"
3. Connect to the router via the Lan port,
set a static ip of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
4. Download initramfs image, reboot router,
waiting for tftp recovery to complete.
5. After openwrt boots up, perform sysupgrade.
Note:
1. Back up all mtd partitions before flashing.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit 4ae474afbd)
Turns out the device got two buttons, while the currently listed on is
actually WPS, and the other (will hidden) button is intended as RESET.
Update DT accordingly.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 646ebbd32c)
The WS-AP3710i does not correctly expose its label-mac on eth0 anymore
since the change to simpleLoader.
Fix this by obtaining the label-mac from the U-Boot environment.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit e321e70ddc)
The TP-Link TL-XTR8488 is silimiar to TL-XDR6088 with following changes:
* 1GB DDR4 RAM
* Addtional MT7915AN for 5.8 GHz wireless
For flash instructions, see the commit for TP-Link TL-XDR6088.
Based on An Yun's work.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 616be733d0)
With the introduction of the simpleImage loader, the MAC address is not
set by the bootloader anymore.
Fix this by reading the MAC address from the U-Boot environment
partition.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 22f92cce22)
On master, the bootwrapper link-address for all simpleImage targets was
relocated to 0x15000000 due to growing kernel size.
This was not done on OpenWrt 23.05, as the decompressed kernel still
fits. However, with the wrapper for the WS-AP3710i, the bootloader
attempts execute in-place with the uImage load-address of 0x1000000. As
the image is compiled without the uImage header in mind, this naturally
fails.
In order to fix this, link the WS-AP3715i simpleImage at 0x15000000 as
done in master. This will force the bootloader to relocate the code to
the proper address and skip XIP.
Signed-off-by: David Bauer <mail@david-bauer.net>
All NETGEAR EX6150v2 validate the rootfs for which OpenWrt places a
fakeheader at the position, where the bootloader expects it.
Some EX6150v2 bootloaders do however make a broken assumption about
where the rootfs starts. This is due to them calculating the rootfs
start not based upon the kernel-length but the string-offset of the
FIT-image.
We have to be compatible with both this broken as well as the valid
calculation. So we do relocate the FDT string section to a
block-boundary and enlarge the FIT image to end at this boundary +
BLOCKSIZE / 2. This way, both the broken as well as correct calculations
do expect the rootfs-header at the same position.
It is worth noting, that this is a rare edge-case in which only happens
if the image-length as well as the start of the string-section are not
placed in the same erase-block. This is an edge-case which happens very
rarely (thus it was not spotted prior).
Affected:
- U-Boot 2012.07 (Jun 16 2016 - 11:59:37)
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit de59fc4540)
The gpio is actually low active, fix it.
Fixes: 40e7fab9e4 ("mediatek: add Nokia EA0326GMP support")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/15651
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 4edde98768)
The MAC address assigned to lan/wan was reversed.
Fixes: f236c1c4f5 ("mediatek: add support for JDCloud RE-CP-03")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The MAC address assigned to lan/wan was reversed on eMMC boards.
Fixes: d3c193525e ("mediatek: add CMCC RAX3000M support")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware
--------
CPU: Freescale P1020 2xe500 PPC
RAM: 256M DDR3 (Micron MT41J64M16JT-15E:G "D9MNJ")
NAND: 128M (Micron 2CA1)
BTN: 1x Reset
LED: Power - ETH - Radio1 - Radio2
UART: RJ-45 Cisco Pinout - 115200 8N1
Installation
------------
NOTE: You can find a repo with up-to-date instructions as well as
the required files here:
https://github.com/blocktrron/msm460-flashing
Required files
==============
You need a command-files as well as a U-Boot image.
The command-file has the following content (padded to 131072 bytes).
If you copy paste these, remove the newlines!
```
U-BOOT setenv ethaddr 02:03:04:05:06:07; setenv ipaddr 192.168.1.1;
setenv serverip 192.168.1.66; tftpboot 0x3000000 msm460-uboot.bin;
nand device; nand erase 0 0xC0000; nand write 0x3000000 0x0 0xC0000; reset
```
You can download the required U-Boot from this repository:
https://github.com/blocktrron/u-boot-msm/releases
Preparation
===========
Prepare a TFTP server serving two files:
- U-Boot NAND image as `msm460-uboot.bin`.
- OpenWrt factory image as `msm460-factory.bin`
- Command-file names `commands.tftp`
You can start a TFTP server in the current directory using dnsmasq:
```bash
sudo dnsmasq --no-daemon --listen-address=0.0.0.0 \
--port=0 --enable-tftp=enxd0 --tftp-root="$(pwd)" \
--user=root --group=root
```
Replace `enxd0` with the name of your network interface.
Procedure
=========
1. Assign yourself the IP-Address 192.168.1.66/24.
3. Connect the Router to the PC while keeping the reset button
pressed.
4. The LEDs will eventually begin to flash.
They will start to flash faster after around 15 seconds.
5. Release the reset button.
6. Start a new shell
7. Make sure you are currently in the directory where the tftp server
is located.
8. Run the following command:
```bash
tftp 192.168.1.1 -m binary -c put commands.tftp nflashd.cccc9999
```
You get the message "Transfer timed out."
To find out if you have been successful, please check the
blinking LED Pattern.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit af329ec389)
Signed-off-by: David Bauer <mail@david-bauer.net>
There is a custom LED controller between the 3 SoC GPIO outputs and
the red and blue LEDs of the device. It implements a strange mapping
that includes fixed, flashing, and breathing modes.
The current DTS configuration causes OpenWrt to flash the LEDs over
the controller's own flashing, resulting in chaotic output in boot,
failsafe, and upgrade modes.
This change fixes the LEDs in the best way possible as long as each
OpenWrt running state is limited to be signaled by a single led.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15440
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 0868268c9f)
Hardware:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 128 MiB SPI NAND
- RAM: 512 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- Ethernet: 1x 10/100/1000/2500 Mbps RTL8221B WAN, 1x10/100/1000 Mbps MT7981 LAN
- USB 3.0 port
- Buttons: 1 Reset button, 1 slider button
- LEDs: 1x Red, 1x White
- Serial console: internal test points, 115200 8n1
- Power: 5 VDC, 3 A
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 80:af:ca:xx:xx:x1 | label+1 |
| LAN | 80:af:ca:xx:xx:x0 | label |
| WLAN 2g | 80:af:ca:xx:xx:x0 | label |
| WLAN 5g | 82:af:ca:xx:xx:x0 | |
+---------+-------------------+-----------+
Installation:
The installation must be done via TFTP by disassembling the router. On other occasions Cudy has distributed intermediate firmware to make installation easier, and so I recommend checking the Wiki for this device if there is a more convenient solution than the one below.
To install using TFTP:
1. Connect to UART.
2. With the router off, press the RESET button. While the router is turning on, the button should continue to be pressed for at least 5 seconds.
3. A u-boot shell will automatically open.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP server and an OpenWrt initramfs-kernel.bin firmware file.
5. Run these steps in u-boot using the name of your file.
setenv bootfile initramfs-kernel.bin
tftpboot
bootm
6. If you can reach LuCI or SSH now, just use the sysupgrade image with the 'Keep settings' option turned off.
Signed-off-by: Luis Mita <luis@luismita.com>
(cherry picked from commit 63b8d98dd0)
The NMBM-Enabled layout did not use fit image,
it just need default process. So it was been removed in platform.sh.
It will fix sysupgrade error for xiaomi,mi-router-wr30u-112m-nmbm.
Signed-off-by: Hank Moretti <mchank9999@gmail.com>
(cherry picked from commit 02214ab8dc)
This reverts commit dcdcfc1511.
This is a firmware for third-party u-boot mod, which should not
be carried here by us.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit 1b7e62b20b)
The patch "710-pci-pcie-mediatek-add-support-for-coherent-DMA.patch"
makes use of "syscon_regmap_lookup_by_phandle" which requires that
"syscon" be in the compatible list.
Without this patch, PCIe probe will fail with the following error:
[ 1.287467] mtk-pcie 1a143000.pcie: host bridge /pcie@1a143000 ranges:
[ 1.294019] mtk-pcie 1a143000.pcie: Parsing ranges property...
[ 1.299901] mtk-pcie 1a143000.pcie: MEM 0x0020000000..0x0027ffffff -> 0x0020000000
[ 1.307954] mtk-pcie 1a143000.pcie: missing hifsys node
[ 1.313185] mtk-pcie: probe of 1a143000.pcie failed with error -22
Fixes: 01c58a0d2a ("kernel: bump 5.15 to 5.15.158")
Signed-off-by: Rany Hany <rany_hany@riseup.net>
(cherry picked from commit 8607372b41)
Fixes: #1298
Fixes: 9744bf7093 ("rockchip: configure ETH LED for FastRhino R66S/R68S")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 72ccbed99c)
All three PCIe ports are reported non working on Meraki MR42/MR52 boards
since kernel 6.1 with the issue of PCIe PHY link never coming up thus
no WLAN cards are available on the boards.
After debugging it seems that PCIe worked on 5.15 and older purely by
accident as device DTS was using /delete-property/ perst-gpios; in each
of the 3 PCIe nodes but there was no "perst-gpios" property in the SoC DTSI
as it was still using the older "perst-gpio" property so it was not getting
removed from the device DTS.
However, in kernel 6.1 commit ("ARM: dts: qcom-*: replace deprecated
perst-gpio with perst-gpios") updated all Qualcomm DTS-es to use the newer
"perst-gpios" and thus once ipq806x moved to 6.1 PCIe stopped working as
now that property was being dropped from the device DTS.
So, since the removal of PERST pins seems to have been wrong from the start
lets drop the property removal from MR42/MR52.
Fixes: #15408
Link: https://github.com/openwrt/openwrt/pull/15509
Link: https://github.com/openwrt/openwrt/pull/15512
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream now uses standard ETH LED bindings to configure LED registers.
However, we don't use the r8169 driver for rockchip, so simply remove
this outdated hack.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit cda5cfb9d5)
The code that was there was just taking whatever was left in the
registers, which was just wrong. Set the addresses using the value from
the u-boot environment, the same way the OEM firmware does.
Signed-off-by: Corey Minyard <minyard@acm.org>
Link: https://github.com/openwrt/openwrt/pull/15358
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15402
Signed-off-by: Robert Marko <robimarko@gmail.com>
Convert the Enterasys WS-AP3710i access point to use the simpleImage
wrapper.
This is necessary, as the bootlaoder does not align the DTB correctly
(and does not support altering the FDT loadaddress). Booting images with
kernels 5.15 and later can break depending on the alignment on the DTB
within the FIT image.
Compared with the patch applied to master, this compiles the loader at
the changed offset used in OpenWrt master. This is required, as U-Boot
loads the uImage at the offset the loader is currently compiled for.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit eec18118d0)
We should setup the registers for trapping LLDP packets to the CPU.
Currently, these packets are forwarded to all ports which is not desired
behaviour.
Signed-off-by: Kevin Jilissen <info@kevinjilissen.nl>
(cherry picked from commit 5a5c52085a)
These registers control the handling of Link Layer Discovery Protocol
(LLDP) packets. This seems to be a typo in the naming.
Signed-off-by: Kevin Jilissen <info@kevinjilissen.nl>
(cherry picked from commit 81ab9ef2d1)
Change the RGB indicator LED color for the running state from green to
blue. There are various reasons for this change:
- In stock firmware, green means internet connection is up, red means it
is down, and blue means indeterminate. To track stock behavior as
closely as possible, OpenWrt should indicate blue by default.
- In the current 23.x OpenWrt releases for this router, the led glows
blue all the time -not green- because the bootloader sets it blue
and there is an OpenWrt bug that makes it unable to control the LED.
The bug is fixed in master, so without this commit there would be an
unexpected change of behavior for this device in the next release.
- The ports other closely related Linksys devices (such as EA8300 and
MR8300) get this right and use blue for the running state.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
(cherry picked from commit c2f52e42b1)
Link: https://github.com/openwrt/openwrt/pull/15438
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RGB LED should glow green in the 'running' state, but it
was glowing cyan because the blue component defaulted to 'on'.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
(cherry picked from commit fc62d66c20)
Link: https://github.com/openwrt/openwrt/pull/15438
Signed-off-by: Robert Marko <robimarko@gmail.com>
LAN Leds on Meraki MR52 are wrong and needs to be swapped to actually
reflect real ports (lan1<->lan2).
Fixes: #15388
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15410
[ wrap commit to 80 columns and improve commit title ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit bd6852185b)
It's the A13-based Olinuxino Micro which has only wireless interfaces. The
A20-based board is a fully-fledged one which has an ethernet interface.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Fixes no communication with tethered iOS devices in CDC NCM mode.
Freshly booted iOS devices start in legacy mode, but are put into
NCM mode by the official Apple driver.
[1] a2d274c62eFixes: #12566
Tested-by: Georgi Valkov <gvalkov@gmail.com>
Signed-off-by: Foster Snowhill <forst@pen.gy>
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
[ better reference fixed issue ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 680f8738d0)
In commit b2d1eb717b ("generic: 5.15: enable Werror by default for
kernel compile") CONFIG_WERROR=y was enabled and all warnings/errors
reported with GCC 12 were fixed.
Keeping this in sync with past/future GCC versions is going to be uphill
battle, so lets introduce new KERNEL_WERROR config option, enable it by
default only for tested/known working combinations and on buildbots.
References: #12687
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit ce8c639a6c)
This device supports channel ranges 36-64 and 100-165, just like
others based on the same reference design, but its current DTS is
unnecessarily restricting these ranges to 36-48 and 149-165.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
(cherry picked from commit 1c32cee348)
Enable LED driver LP5562 on HAZE device tree and include its kernel
module package on default package for HAZE.
Signed-off-by: CheWei Chien <chewei.chien@wnc.com.tw>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [commit facelift]
(cherry picked from commit fb45194305)
The sysupgrade formware of the Puzzle series is a slightly strange
dual-boot approach while remaining compatible with Marvell's SDK
firmware upgrade binary format -- which happens to be a full-disk
image with GPT partition table. Hence that /lib/upgrade/emmc-puzzle.sh
script is like an exotic disease which results from those decisions,
and as we also want to somehow stay compatible with the IEI-World
stock firmware we got to use it in that same way (we are not
compatible with the QNAP-branded identical hardware device anyway).
Currently, on sysupgrade the result is that one ends up with the old
content of rootfs_data (a GPT partition on those devices) as nothing
ever wipes or in any way re-creates the filesystem there. As a simple
work-around, let's kill the filesystem on rootfs_data so fstools
re-formats it on the next boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit d4e8653e1e)
D-Link DGS-1210-16 hangs when rebooting and has no support for the reset
button.
Fix both by enabling the same GPIOs for reboot and the reset button as
already used for D-Link DGS-1210-20 and D-Link DGS-1210-28.
Signed-off-by: Richard Kunze <kunze@tivano.de>
(cherry picked from commit 92c21b2e18)
Huawei AP5030DN is a dual-band, dual-radio 802.11ac Wave 1 3x3 MIMO
enterprise access point with two Gigabit Ethernet ports and PoE
support.
Hardware highlights:
- CPU: QCA9550 SoC at 720MHz
- RAM: 256MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi 2.4GHz: QCA9550-internal radio
- Wi-Fi 5GHz: QCA9880 PCIe WLAN SoC
- Ethernet 1: 10/100/1000 Mbps Ethernet through Broadcom B50612E PHY
- Ethernet 2: 10/100/1000 Mbps Ethernet through Marvell 88E1510 PHY
- PoE: input through Ethernet 1 port
- Standalone 12V/2A power input
- Serial console externally available through RJ45 port
- External watchdog: SGM706 (1.6s timeout)
Serial console:
9600n8 (9600 baud, no stop bits, no parity, 8 data bits)
MAC addresses:
Each device has 32 consecutive MAC addresses allocated by
the vendor, which don't overlap between devices.
This was confirmed with multiple devices with consecutive
serial numbers.
The MAC address range starts with the address on the label.
To be able to distinguish between the interfaces,
the following MAC address scheme is used:
- eth0 = label MAC
- eth1 = label MAC + 1
- radio0 (Wi-Fi 5GHz) = label MAC + 2
- radio1 (Wi-Fi 2.4GHz) = label MAC + 3
Installation:
0. Connect some sort of RJ45-to-USB adapter to "Console" port of the AP
1. Power up the AP
2. At prompt "Press f or F to stop Auto-Boot in 3 seconds",
do what they say.
Log in with default admin password "admin@huawei.com".
3. Boot the OpenWrt initramfs from TFTP using the hidden script
"run ramboot". Replace IP address as needed:
> setenv serverip 192.168.1.10
> setenv ipaddr 192.168.1.1
> setenv rambootfile
openwrt-ath79-generic-huawei_ap5030dn-initramfs-kernel.bin
> saveenv
> run ramboot
4. Optional but recommended as the factory firmware cannot
be downloaded publicly:
Back up contents of "firmware" partition using the web interface or ssh:
$ ssh root@192.168.1.1 cat /dev/mtd11 > huawei_ap5030dn_fw_backup.bin
5. Run sysupgrade using sysupgrade image. OpenWrt
shall boot from flash afterwards.
Return to factory firmware (using firmware upgrade package downloaded from
non-public Huawei website):
1. Start a TFTP server in the directory where
the firmware upgrade package is located
2. Boot to u-boot as described above
3. Install firmware upgrade package and format the config partitions:
> update system FatAP5X30XN_SOMEVERSION.bin
> format_fs
Return to factory firmware (from previously created backup):
1. Copy over the firmware partition backup to /tmp,
for example using scp
2. Use sysupgrade with force to restore the backup:
sysupgrade -F huawei_ap5030dn_fw_backup.bin
3. Boot AP to U-Boot as described above
Quirks and known issues
-----------------------
- On initial power-up, the Huawei-modified bootloader suspends both
ethernet PHYs (it sets the "Power Down" bit in the MII control
register). Unfortunately, at the time of the initial port, the kernel
driver for the B50612E/BCM54612E PHY behind eth0 doesn't have a resume
callback defined which would clear this bit. This makes the PHY unusable
since it remains suspended forever. This is why the backported kernel
patches in this commit are required which add this callback and for
completeness also a suspend callback.
- The stock firmware has a semi dual boot concept where the primary
kernel uses a squashfs as root partition and the secondary kernel uses
an initramfs. This dual boot concept is circumvented on purpose to gain
more flash space and since the stock firmware's flash layout isn't
compatible with mtdsplit.
- The external watchdog's timeout of 1.6s is very hard to satisfy
during bootup. This is why the GPIO15 pin connected to the watchdog input
is configured directly in the LZMA loader to output the CPU_CLK/4 signal
which keeps the watchdog happy until the wdt-gpio kernel driver takes
over. Because it would also take too long to read the whole kernel image
from flash, the uImage header only includes the loader which then reads
the kernel image from flash after GPIO15 is configured.
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
[fixed 6.6 backport patch naming]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 06cdc07f8c)
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, WPS/Mesh
Power: DC 12V 1A
Gain SSH access:
1. Login into web interface, and download the configuration.
2. Download the configration utilities:
https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7981-nokia-ea0326gmp-config-utils.tar.gz
These binaries are extraced from the factory firmware, which are
dynamically linked with aarch64 musl 1.1.24. To use them, you
must run them under the same runtime environment, otherwise the
binaries will not work properly!
3. Upload the configuration and utilities to a suitable environment.
4. Uncompress the utilities, move them to '/bin' and give them executable permisison:
tar -zxf openwrt-mediatek-mt7981-nokia-ea0326gmp-config-utils.tar.gz
mv mkconfig seama /bin
chmod +x /bin/mkconfig
chmod +x /bin/seama
5. Decrypt and uncompress the configuration:
Enter fakeroot if you are not login as root.
mkconfig -a de-enca -m EA0326GMP_3FE79221BAAA -i EA0326GMP_3FE79221BAAA-xxxxxxxx-backup.tar.gz -o backup.tar.gz
tar -zxf backup.tar.gz
6. Edit 'etc/config/dropbear', set 'enable' to '1'.
7. Edit `etc/passwd`, remove root password: 'root::1:0:99999:7:::'.
8. Repack the configuration:
tar -zcf backup.tar.gz etc/
mkconfig -a enca -m EA0326GMP_3FE79221BAAA -i backup.tar.gz -o EA0326GMP_3FE79221BAAA-xxxxxxxx-backup.tar.gz
9. Upload new configuration via web interface, now you can SSH to EA0326GMP.
A minimum configuration which enabled SSH access is also provided to simplify the process:
https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7981-nokia-ea0326gmp-enable-ssh.tar.gz
Flash instructions:
1. SSH to EA0326GMP, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write immortalwrt-mediatek-filogic-nokia_ea0326gmp-preloader.bin BL2
3. Write new FIP:
mtd write immortalwrt-mediatek-filogic-nokia_ea0326gmp-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve ImmortalWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. Run 'fw_setenv bootargs' if comes with SNAPSHOT u-boot.
8. After ImmortalWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 767c4681fd)
[updated flash instructions for 23.05 branch]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 8GB eMMC or 128 MB SPI-NAND
RAM: 256MB
Ethernet: 5x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset
USB: M.2(B-key) for 4G/5G Module
Power: DC 12V 1A
UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | VCC RX TX GND | <= |
| ----------------- |
--------------------------
The U-boot menu will automatically appear at startup, and then select
the required options through UP/DOWN Key.
NAND Flash and eMMC Flash instructions:
1. Set your computers IP adress to 192.168.1.2.
2. Run a TFTP server providing the sysupgrade.bin image.
3. Power on the router, into the U-Boot menu.
4. Select "2. Upgrade firmware"
5. Update sysupgrade.bin file name, input server IP and input device
IP (if they deviate from the defaults)
6. Wait for automatic startup after burning
Signed-off-by: Allen Zhao <allenzhao@unielecinc.com>
(cherry picked from commit 640b0b79ff)
ttyS2 is the default console used for all rockchip boards.
The redundant 'console=tty1' parameter now breaks the console due to
recent procd update.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 163c3d0bde)
We have hardware IOMMU support and this is totally unnecessary.
The given value is also unreasonable, it's too small and causes
kernel panic in some cases:
[ 5706.856473] sdhci-dwcmshc fe310000.mmc: swiotlb buffer is full (sz: 28672 bytes), total 512 (slots), used 498 (slots)
[ 5706.864451] sdhci-dwcmshc fe310000.mmc: swiotlb buffer is full (sz: 65536 bytes), total 512 (slots), used 464 (slots)
This parameter seems to be added by mistake, so remove it.
Fixes: e35c7ab51f ("rockchip: merge bootscript")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 50e6c8ae8d)
We have hardware IOMMU support and this is totally unnecessary.
The given value is also unreasonable, it's too small and causes
kernel panic in some cases:
[ 5706.856473] sdhci-dwcmshc fe310000.mmc: swiotlb buffer is full (sz: 28672 bytes), total 512 (slots), used 498 (slots)
[ 5706.864451] sdhci-dwcmshc fe310000.mmc: swiotlb buffer is full (sz: 65536 bytes), total 512 (slots), used 464 (slots)
This parameter seems to be added by mistake, so remove it.
Fixes: 058bdf0396 ("rockchip: lzma compression for kernel")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 158e54ce28)
* have more defined PWM steps similar to the vendor's shell script doing
the same thing
* replace PWM values with experiencal values provided by forum users
* increase hyteresis to prevent changing fan speed every second
(just because it's annoying to listen to)
* add 'hot' trip point at 75 deg. to warn users that shutdown is imminent
Tested on Puzzle M902 only for now, PWM values for Puzzle M901 might be
slightly different but should quite certainly also be rised.
Suggested-by: Martin Gierschner <martin_gierschner@gmx.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 1a47ce5ff2)
Set 12mA driving strength for SPI-NAND pins like the stock firmware's
bootloader does as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 45a2109353)
Some Aquantia PHYs (e.g. AQR113C) require firmware to be uploaded by
host system. With built-in drivers this doesn't work in OpenWrt /
embeddded as filesystem isn't available during PHY probe. That results
in delays like:
[ 1.588068] Aquantia AQR113C mdio-bus:00: Falling back to sysfs fallback for: Rhe-05.06-Candidate9-AQR_Mediatek_23B_P5_ID45824_LCLVER1.cld
[ 64.526387] Aquantia AQR113C mdio-bus:00: failed to find FW file Rhe-05.06-Candidate9-AQR_Mediatek_23B_P5_ID45824_LCLVER1.cld (-110)
Switch to module to postpone PHY probe to init state.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 3bd79e6136)
Marvell's thermal sensors do not support interrupts, so we need to
poll them. Reading temperature every second should be enough to
control the fan.
While at it, also make sure fan speed is reduced again if temperature
goes down.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit fc177695e0)
