Removing i2c pxa slave
The i2c-pxa is typically not use in slave mode. It does not make sense
to have slave mode enabled by default.
Having slave mode enabled prevents the i2c controller from being reset
if a real slave device such as an SFP is attached to the i2c-pxa bus and
locks it up.
Disable slave mode so that the i2c controller can be reset if the bus is
locked up.
If someone actually has a need for pxa slave mode this can be enabled in
kernel config.
Signed-off-by: Scott Roberts <ttocsr@gmail.com>
Remove leds-apu2 out of tree driver. There is a new upstream device gpio
and leds driver stack available for the APUv2 and APUv3 boards from pc
egnines. This new driver stack was add in kernel version 4.15.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
This updates to the last firmware version before the switch to building
from the common firmware branch, which introduces various issues.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
This reverts commit 9e467a764b.
The Raspberry Pi firmware recently switched to building from the common
firmware branch. This introduces changes in the core clock handling,
causing various issues.
E.g. enable_uart=1 no longer fixes the core clock frequency to 250MHz.
When the disable-bt DT overlay is not loaded, the core clock frequency
is increased to 400MHz. As a result, the UART baud rate is no longer
correct, and this causes garbled serial console, or communication
problems with HATs that use the UART.
As a workaround, the core clock could be fixed to 250MHz by adding
'core_freq=250' in /boot/config.txt, but as there appear to be other
issues than just the UART being broken, the safer bet is to revert the
firmware for now.
Upstream bug: https://github.com/raspberrypi/firmware/issues/1376
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
As reported in https://github.com/openwrt/packages/issues/12072, the
imagebuilder fails due to a dependency resolution error when the userspace
packages are built using a target that has a different kernel version than
that which is being run. To resolve this, add a virtual kernel package with
the conditional dependency currently used in sqm-scripts. The idea is to
move the sqm-scripts dependency to this virtual package, which hopefully
should be consistent with the actual kernel module being built.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Use in tree version of cake for kernels 4.19+ and backport features from
later kernel versions to 4.19.
Unfortunately PROVIDES dependency handling produces bogus circular
dependency warnings so whilst this package and kmod-sched-cake-oot
should be able to PROVIDE kmod-sched-cake this doesn't work.
Instead, remove the PROVIDES option and modify package sqm-scripts to
depend on the correct module independently.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
In preparation for dropping the out of tree cake module and using
in tree cake from upstream, rename the package to kmod-sched-cake-oot
(out of tree)
Initially add a PROVIDES kmod-sched-cake so that package dependencies
can be satisfied.
Ultimately this package will be removed when linux 4.14 is removed.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Add kmod for the ST LSM6DSX IMU driver.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
[fixed missing regmap module dependencies]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since commit 910df3f06c we have build in
on all X86/64 platforms the gpio-it87 driver.
Since this change I am getting the following error message on boot.
> kern.err kernel: [ 1.009416] gpio_it87: no device
I do not have this device on my system. To prevent the nonsensical
message and the loading of the module I have added this as a package, so
that it can be installed later or during image building.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
Add a local hack to prevent the Broadcom WPA authenticator process from
inheriting the lock descriptor 1000 used to prevent concurrent executions
of the init script.
Without this fix, repeated invocations of /etc/init.d/network, e.g. for
obtaining the enabled state, would hang forever.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This drops kernel version switches for versions not supported by
OpenWrt master at the moment. This only adjusts local code, but
doesn't touch patches to existing external packages.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This updates the package to contain the kernel object (.ko) file instead
of the plain object (.o) file.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
When CONFIG_AUTOREMOVE is enabled, CFE binaries are removed before the
image creation.
Install CFE binaries to kernel directory and let autoremove clean the
files in PKG_BUILD_DIR.
Also drop unneeded tar cmd/options.
Fixes: dcee4eaa42 ("bcm63xx-cfe: add package with CFE RAM binaries")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
CFE RAM is a second stage bootloader which is usually loaded by CFE ROM
(first stage bootloader) from a JFFS2 partition stored on the NAND.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
