This Fixes the folowing compile error:
drivers/mtd/nand/rb91x_nand.c: In function 'rb91x_nand_remove':
drivers/mtd/nand/rb91x_nand.c:445:16: error: 'rbni' undeclared (first use in this function)
nand_release(&rbni->chip);
Fixes: ce958dd88a ("kernel: Update kernel 4.14 to version 4.14.187")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There is one closing bracket too much.
Fixes: ce958dd88a ("kernel: Update kernel 4.14 to version 4.14.187")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes:
- CVE-2020-10757
The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was
backported which needed some adaptations to other code.
Build tested: ramips
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The TP-Link TL-MR3020 has a three-state mode slider which was previously
integrated as a button (EV_KEY). This led to spurious activations of
failsafe mode.
Set the type for the button to switch (EV_SW), to avoid unintended
activations of failsafe mode.
Related: commit 27f3f493de ("gpio-button-hotplug: unify polled and
interrupt code")
Signed-off-by: David Bauer <mail@david-bauer.net>
During porting support for this router to ath79 target
it was discovered that GPIO mapping was incorrect (GPIO11 active high).
Correct mapping for both V1 and V2 is GPIO12 active low.
Default configuration from GPL source for V2 explicitly states this, and
this was confirmed experimentally on ath79 by looking on
/sys/kernel/debug/gpio. Correctness of this was also validated for V1 by
cross-flashing vendor firmware for V1 on V2 hardware, in which reset
button also worked.
Fix it.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[slightly adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The -O option for the tplink-v1-header was missing for the TP-Link
TL-WR902AC v1, while safeloader and MTDPARTS where set up with a
single firmware partition.
This led to bootloops after using sysupgrade.
Fixes: FS#3118
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link TL-WR882N/WR885N/WR886N
This adds support for the various clones of the TL-WR885N recently
supported ("ath79: add support for TP-Link TL-WR885N v1"):
- tplink,tl-wr882n-v1
- tplink,tl-wr882n-v2
- tplink,tl-wr882n-v3
- tplink,tl-wr885n-v1
- tplink,tl-wr885n-v2
- tplink,tl-wr886n-v2
- tplink,tl-wr886n-v3
- tplink,tl-wr886n-v4
- tplink,tl-wr886n-v5
- tplink,tl-wr886n-v6
- tplink,tl-wr886n-v7
These devices are cloned in ar71xx. All models added in this patch are the same hardware CPU
WR885n V2 was tested.
Specifications:
- SOC: Qualcomm Atheros TP9343-AL3A
- CPU: 750MHz
- Flash: 2 MiB (AH1446 25Q16BS1G E5N102)
- RAM: 16 MiB (Zentel A3S28D40JTP-50)
- WLAN: Qualcomm Atheros TP9343 450Mbps
- Ethernet: Atheros AR8228/AR8229 4 port (100M)
添加TP9343芯片的路由器型号支持，TL-WR882N/WR885N/WR886N系列
* ath79: add support for MerCury MW4530R v1
重新添加水星MW4530R路由器支持
* Repair generate mw4530r firmware default is 8M
* Fix mw4530r forgot to add network settings
* ath79: add support for TP-Link TL-WR882N/WR885N/WR886N
This adds support for the various clones of the TL-WR885N recently
supported ("ath79: add support for TP-Link TL-WR885N v1"):
- tplink,tl-wr882n-v1
- tplink,tl-wr882n-v2
- tplink,tl-wr882n-v3
- tplink,tl-wr885n-v1
- tplink,tl-wr885n-v2
- tplink,tl-wr886n-v2
- tplink,tl-wr886n-v3
- tplink,tl-wr886n-v4
- tplink,tl-wr886n-v5
- tplink,tl-wr886n-v6
- tplink,tl-wr886n-v7
These devices are cloned in ar71xx. All models added in this patch are the same hardware CPU
WR885n V2 was tested.
Specifications:
- SOC: Qualcomm Atheros TP9343-AL3A
- CPU: 750MHz
- Flash: 2 MiB (AH1446 25Q16BS1G E5N102)
- RAM: 16 MiB (Zentel A3S28D40JTP-50)
- WLAN: Qualcomm Atheros TP9343 450Mbps
- Ethernet: Atheros AR8228/AR8229 4 port (100M)
添加TP9343芯片的路由器型号支持，TL-WR882N/WR885N/WR886N系列
* ath79: add support for MerCury MW4530R v1
重新添加水星MW4530R路由器支持
* Repair generate mw4530r firmware default is 8M
The AVM FRITZ!WLAN Repeater 450E's WPS button is not active low.
Correct the active low flag to avoid unintenional activation of
failsafe mode on boot.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 1d4f2ca610)
When changing the LED names for the Archer C7 to represent the correct
color, a migration for existing UCI entries was not created.
Add a migration to keep existing LED configurations working.
Fixes commit c79c001b59 ("ar71xx: Archer C7 v1 LED names and RFKILL
fixes")
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 4349d4c682)
