fish/immortalwrt
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
1dd036a659
immortalwrt/target/linux/ath79/dts
History
Kevin Abraham 1dd036a659 ath79: add support for Senao Engenius ENS1750 
FCC ID: A8J-EWS660AP

Engenius ENS1750 is an outdoor wireless access point with
2 gigabit ethernet ports, dual-band wireless,
internal antenna plates, and 802.3at PoE+

Engenius EWS660AP, ENS1750, and ENS1200 are "electrically identical,
different model names are for marketing purpose" according to docs
provided by Engenius to the FCC.

**Specification:**

  - QCA9558 SOC		2.4 GHz, 3x3
  - QCA9880 WLAN	mini PCIe card, 5 GHz, 3x3, 26dBm
  - AR8035-A PHY	RGMII GbE with PoE+ IN
  - AR8033 PHY		SGMII GbE with PoE+ OUT
  - 40 MHz clock
  - 16 MB FLASH		MX25L12845EMI-10G
  - 2x 64 MB RAM
  - UART at J1		populated, RX grounded
  - 6 internal antenna plates (5 dbi, omni-directional)
  - 5 LEDs, 1 button (power, eth0, eth1, 2G, 5G) (reset)

**MAC addresses:**

  Base MAC addressed labeled as "MAC"
  Only one Vendor MAC address in flash

  eth0 *:d4 MAC art 0x0
  eth1 *:d5 --- art 0x0 +1
  phy1 *:d6 --- art 0x0 +2
  phy0 *:d7 --- art 0x0 +3

**Serial Access:**

  the RX line on the board for UART is shorted to ground by resistor R176
  therefore it must be removed to use the console
  but it is not necessary to remove to view boot log

  optionally, R175 can be replaced with a solder bridge short

  the resistors R175 and R176 are next to the UART RX pin

**Installation:**

  2 ways to flash factory.bin from OEM:

  Method 1: Firmware upgrade page:

    OEM webpage at 192.168.1.1
    username and password "admin"
    Navigate to "Firmware Upgrade" page from left pane
    Click Browse and select the factory.bin image
    Upload and verify checksum
    Click Continue to confirm and wait 3 minutes

  Method 2: Serial to load Failsafe webpage:

    After connecting to serial console and rebooting...
    Interrupt uboot with any key pressed rapidly
    execute `run failsafe_boot` OR `bootm 0x9fd70000`
    wait a minute
    connect to ethernet and navigate to
    "192.168.1.1/index.htm"
    Select the factory.bin image and upload
    wait about 3 minutes

**Return to OEM:**

  If you have a serial cable, see Serial Failsafe instructions
  otherwise, uboot-env can be used to make uboot load the failsafe image

  ssh into openwrt and run
  `fw_setenv rootfs_checksum 0`
  reboot, wait 3 minutes
  connect to ethernet and navigate to 192.168.1.1/index.htm
  select OEM firmware image from Engenius and click upgrade

**TFTP recovery:**

  Requires serial console, reset button does nothing

  rename initramfs.bin to '0101A8C0.img'
  make available on TFTP server at 192.168.1.101
  power board, interrupt boot
  execute tftpboot and bootm 0x81000000

**Format of OEM firmware image:**

  The OEM software of ENS1750 is a heavily modified version
  of Openwrt Kamikaze. One of the many modifications
  is to the sysupgrade program. Image verification is performed
  simply by the successful ungzip and untar of the supplied file
  and name check and header verification of the resulting contents.
  To form a factory.bin that is accepted by OEM Openwrt build,
  the kernel and rootfs must have specific names...

    openwrt-ar71xx-generic-ens1750-uImage-lzma.bin
    openwrt-ar71xx-generic-ens1750-root.squashfs

  and begin with the respective headers (uImage, squashfs).
  Then the files must be tarballed and gzipped.
  The resulting binary is actually a tar.gz file in disguise.
  This can be verified by using binwalk on the OEM firmware images,
  ungzipping then untaring.

  Newer EnGenius software requires more checks but their script
  includes a way to skip them, otherwise the tar must include
  a text file with the version and md5sums in a deprecated format.

  The OEM upgrade script is at /etc/fwupgrade.sh.

  OKLI kernel loader is required because the OEM software
  expects the kernel to be no greater than 1536k
  and the factory.bin upgrade procedure would otherwise
  overwrite part of the kernel when writing rootfs.

Note on PLL-data cells:

  The default PLL register values will not work
  because of the external AR8035 switch between
  the SOC and the ethernet port.

  For QCA955x series, the PLL registers for eth0 and eth1
  can be see in the DTSI as 0x28 and 0x48 respectively.
  Therefore the PLL registers can be read from uboot
  for each link speed after attempting tftpboot
  or another network action using that link speed
  with `md 0x18050028 1` and `md 0x18050048 1`.

  The clock delay required for RGMII can be applied
  at the PHY side, using the at803x driver `phy-mode`.
  Therefore the PLL registers for GMAC0
  do not need the bits for delay on the MAC side.
  This is possible due to fixes in at803x driver
  since Linux 5.1 and 5.3

Tested-by: Kevin Abraham <kevin@westhousefarm.com>
Signed-off-by: Kevin Abraham <kevin@westhousefarm.com>
2024-05-11 16:57:28 +02:00
..
ar724x_senao_loader-4k.dtsi ath79: add Senao 'failsafe' sysupgrade procedure 2021-04-08 09:20:59 +02:00
ar724x_senao_loader-64k.dtsi ath79: add Senao 'failsafe' sysupgrade procedure 2021-04-08 09:20:59 +02:00
ar724x_ubnt_xm_outdoor.dtsi ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar724x_ubnt_xm.dtsi ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar724x.dtsi ath79: rename pcie-controller to pcie 2024-01-05 16:17:57 +01:00
ar934x_ruckus_zf73xx.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar934x_senao_loader.dtsi ath79: add Senao 'failsafe' sysupgrade procedure 2021-04-08 09:20:59 +02:00
ar934x.dtsi ath79: fix avoid_unnecessary_addr_size warnings 2024-01-05 16:17:57 +01:00
ar1022_iodata_wn-ag300dgr.dts ath79: enable UART in SoC DTSI files 2021-02-24 02:53:53 +01:00
ar1022_sitecom_wlr-7100.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7100_mikrotik_routerboard-4xx.dtsi ath79: cleanup mikrotik routerboot partitions 2022-04-15 07:11:18 +02:00
ar7100.dtsi ath79: rename pcie-controller to pcie 2024-01-05 16:17:57 +01:00
ar7161_adtran_bsap1800-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7161_adtran_bsap1840.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7161_adtran_bsap1880.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7161_aruba_ap-105.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7161_aruba_ap-175.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7161_buffalo_wzr-600dhp.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7161_buffalo_wzr-hp-ag300h.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7161_buffalo_wzr-hp-ag300h.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7161_dlink_dir-825-b1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7161_fortinet_fap-220-b.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7161_jjplus_ja76pf2.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar7161_meraki_mr16.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7161_mikrotik_routerboard-493g.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7161_netgear_wndap360.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7161_netgear_wndr3700-v2.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar7161_netgear_wndr3700.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar7161_netgear_wndr3800.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar7161_netgear_wndr3800ch.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar7161_netgear_wndr.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7161_netgear_wndrmac-v1.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar7161_netgear_wndrmac-v2.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar7161_ruckus_gd11.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7161_ruckus_zf734x.dtsi ath79: support Ruckus ZoneFlex 7341/7343/7363 2023-03-22 22:25:08 +01:00
ar7161_ruckus_zf7341.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar7161_ruckus_zf7351.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar7161_ruckus_zf7363.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar7161_siemens_ws-ap3610.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7161_trendnet_tew-673gru.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7161_ubnt_routerstation-pro.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7161_ubnt_routerstation.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7161_ubnt_routerstation.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar7240_buffalo_whr-g301n.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7240_dlink_dir-615-e4.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7240_engenius_enh202-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7240_netgear_wnr612-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_netgear_wnr612-v2.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7240_netgear_wnr1000-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7240_on_n150r.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_openmesh_om2p-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7240_ruckus_zf7025.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7240_tplink_tl-wa701nd-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wa730re-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wa801nd-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wa830re-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wa901nd-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wa.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7240_tplink_tl-wr740n-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wr740n-v3.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wr741-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wr743nd-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wr841-v5.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wr941-v4.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wr.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7240_tplink.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7240_ubnt_bullet-m-ar7240.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar7241_netgear_wnr2000-v3.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7241_netgear_wnr2200-8m.dts ath79: ar: convert to mac-base 2023-11-25 21:34:18 -08:00
ar7241_netgear_wnr2200-16m.dts ath79: ar: convert to mac-base 2023-11-25 21:34:18 -08:00
ar7241_netgear_wnr2200.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7241_tplink_tl-mr3x20.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar7241_tplink_tl-mr3220-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7241_tplink_tl-mr3420-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7241_tplink_tl-wr841-v7.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7241_tplink_tl-wr842n-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7241_tplink.dtsi ath79: ar: convert to mac-base 2023-11-25 21:34:18 -08:00
ar7241_ubnt_airrouter.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7241_ubnt_bullet-m-ar7241.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7241_ubnt_nanobridge-m.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7241_ubnt_nanostation-loco-m.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7241_ubnt_nanostation-m.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7241_ubnt_picostation-m.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7241_ubnt_powerbridge-m.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7241_ubnt_rocket-m.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7241_ubnt_unifi-ap-lr.dts ath79: add variant UniFi AP LR 2022-08-06 20:15:30 +02:00
ar7241_ubnt_unifi-ap-outdoor-plus.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar7241_ubnt_unifi-ap.dts ath79: rename references of UniFi to UniFi AP 2022-08-06 20:15:30 +02:00
ar7241_ubnt_unifi-ap.dtsi ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar7241_ubnt_unifi.dtsi ath79: convert WiFis based on ar7241_ubnt_unifi.dtsi to nvmem-cells 2022-12-17 20:48:57 +01:00
ar7241.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar7242_avm_fritz300e.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7242_buffalo_bhr-4grv.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar7242_buffalo_wzr-bhr.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7242_buffalo_wzr-hp-g302h-a1a0.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7242_buffalo_wzr-hp-g450h.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar7242_engenius_eap350-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7242_engenius_ecb350-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7242_meraki_mr12.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7242_tplink_tl-wr2543-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7242_ubnt_edgeswitch-5xp.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar7242_ubnt_edgeswitch-8xp.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar7242_ubnt_sw.dtsi ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar7242.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar9132_buffalo_wzr-hp-g300nh-rb.dts ath79: Add support for Buffalo WZR-HP-G300NH 2021-03-22 09:23:10 +01:00
ar9132_buffalo_wzr-hp-g300nh-s.dts ath79: Add support for Buffalo WZR-HP-G300NH 2021-03-22 09:23:10 +01:00
ar9132_buffalo_wzr-hp-g300nh.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9132_tplink_tl-wa901nd-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9132_tplink_tl-wr941-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9132_tplink_tl-wr1043nd-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9132.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar9330_dlink_dir-505.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9330_glinet_gl-ar150.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9330_openmesh_om2p-lc.dts ath79: Add support for OpenMesh OM2P-LC 2020-12-30 23:32:07 +01:00
ar9330_openmesh_om2p-v2.dts ath79: Add support for OpenMesh OM2P v2 2020-12-30 23:32:07 +01:00
ar9330_openmesh_om2p.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9330_pqi_air-pen.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9330_ziking_cpe46b.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9330.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar9331_8dev_carambola2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9331_alfa-network_ap121f.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar9331_alfa-network_ap121f.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9331_alfa-network_ap121fe.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar9331_arduino_yun.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9331_embeddedwireless_dorin.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9331_etactica_eg200.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9331_glinet_64xx.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9331_glinet_6408.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar9331_glinet_6416.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar9331_glinet_gl-mifi.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9331_glinet_gl-usb150.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9331_hak5_lan-turtle.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar9331_hak5_lan-turtle.dtsi ath79: ar: convert to mac-base 2023-11-25 21:34:18 -08:00
ar9331_hak5_packet-squirrel.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar9331_hak5_wifi-pineapple-nano.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar9331_hiwifi_hc6361.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9331_onion_omega.dts ath79: gpio to gpios 2024-01-05 16:17:58 +01:00
ar9331_pisen_ts-d084.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar9331_pisen_wmm003n.dts ath79: gpio to gpios 2024-01-05 16:17:58 +01:00
ar9331_teltonika_rut230-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9331_tplink_tl-mr10u.dts ath79: gpio to gpios 2024-01-05 16:17:58 +01:00
ar9331_tplink_tl-mr3020-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9331_tplink_tl-mr3040-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9331_tplink_tl-wr703n_tl-mr10u.dtsi ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar9331_tplink_tl-wr703n.dts ath79: gpio to gpios 2024-01-05 16:17:58 +01:00
ar9331_tplink_tl-wr710n-8m.dtsi ath79: ar: convert to mac-base 2023-11-25 21:34:18 -08:00
ar9331_tplink_tl-wr710n-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9331_tplink_tl-wr710n-v2.1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9331_tplink_tl-wr710n.dtsi ath79: gpio to gpios 2024-01-05 16:17:58 +01:00
ar9331_tplink_tl-wr740n-v4.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9331_tplink_tl-wr740n-v5.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9331_tplink_tl-wr741nd-v4.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9331_tplink_tl-wr741nd-v4.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9331.dtsi ath79: add missing clock name strings in SoC dtsi 2022-11-09 22:55:33 +01:00
ar9341_engenius_eap300-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9341_engenius_ens202ext-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9341_openmesh_om2p-hs-v1.dts ath79: add support for OpenMesh OM2P-HS v1 2020-12-29 00:03:26 +01:00
ar9341_openmesh_om2p-hs-v2.dts ath79: add support for OpenMesh OM2P-HS v2 2020-12-29 00:03:26 +01:00
ar9341_openmesh_om2p-hs-v3.dts ath79: add support for OpenMesh OM2P-HS v3 2020-12-29 00:03:26 +01:00
ar9341_openmesh_om2p-hs.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9341_pcs_cr3000.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9341_pisen_wmb001n.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar9341_tplink_tl-mr3420-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9341_tplink_tl-wa850re-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9341_tplink_tl-wa860re-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9341_tplink_tl-wa901nd-v3.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9341_tplink_tl-wa.dtsi ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar9341_tplink_tl-wr841-v8.dts ath79: ar: convert to mac-base 2023-11-25 21:34:18 -08:00
ar9341_tplink_tl-wr842n-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9341_tplink_tl-wr941nd-v5.dts ath79: ar: convert to mac-base 2023-11-25 21:34:18 -08:00
ar9341_tplink.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9341.dtsi ath79: do not set inherited phy-mode/status properties again 2020-01-31 13:42:12 +01:00
ar9342_iodata_etg3-r.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9342_mikrotik_routerboard-911g-xhpnd.dts ath79: support for MikroTik RouterBOARD 911G-(2,5)HPnD 2024-01-07 01:19:54 +01:00
ar9342_mikrotik_routerboard-911g.dtsi ath79: add MikroTik suffix to the local GPIO latch driver 2024-05-09 23:51:14 +02:00
ar9342_mikrotik_routerboard-912uag-2hpnd.dts ath79: support for MikroTik RouterBOARD 911G-(2,5)HPnD 2024-01-07 01:19:54 +01:00
ar9342_ruckus_zf7321.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9342_ubnt_aircube-ac.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar9342_ubnt_bullet-ac.dts ath79: Add support for Ubiquiti Bullet AC 2021-01-15 18:32:38 +01:00
ar9342_ubnt_bullet-m-xw.dts ath79: ubnt-bullet-m-xw: fix Ethernet PHY traffic 2024-01-25 23:45:41 +01:00
ar9342_ubnt_lap-120.dts ath79: create DTSI files for ubnt WA 1-/2-port devices 2020-11-03 18:34:10 +01:00
ar9342_ubnt_litebeam-ac-gen2.dts ath79: remove redundant setup of wmac for ubnt WA devices 2020-11-03 18:34:10 +01:00
ar9342_ubnt_litebeam-m5-xw.dts ath79: generic: rework ar9342_ubnt_xw dtsi, and add support for Ubiquiti LiteBeam M5 (XW), Ubiquiti AirGrid M5 HP (XW), Ubiquiti PowerBeam M5 300 (XW) 2024-01-20 19:57:57 +01:00
ar9342_ubnt_nanobeam-ac-gen2.dts ath79: Add support for Ubiquiti NanoBeam AC Gen2 2020-11-18 21:13:46 +01:00
ar9342_ubnt_nanobeam-ac.dts ath79: Add support for Ubiquiti NanoBeam AC Gen2 2020-11-18 21:13:46 +01:00
ar9342_ubnt_nanostation-ac-loco.dts ath79: remove redundant setup of wmac for ubnt WA devices 2020-11-03 18:34:10 +01:00
ar9342_ubnt_nanostation-ac.dts ath79: remove redundant setup of wmac for ubnt WA devices 2020-11-03 18:34:10 +01:00
ar9342_ubnt_nanostation-loco-m-xw.dts ath79: generic: rework ar9342_ubnt_xw dtsi, and add support for Ubiquiti LiteBeam M5 (XW), Ubiquiti AirGrid M5 HP (XW), Ubiquiti PowerBeam M5 300 (XW) 2024-01-20 19:57:57 +01:00
ar9342_ubnt_nanostation-m-xw.dts ath79: generic: rework ar9342_ubnt_xw dtsi, and add support for Ubiquiti LiteBeam M5 (XW), Ubiquiti AirGrid M5 HP (XW), Ubiquiti PowerBeam M5 300 (XW) 2024-01-20 19:57:57 +01:00
ar9342_ubnt_powerbeam-5ac-gen2.dts ath79: create DTSI files for ubnt WA 1-/2-port devices 2020-11-03 18:34:10 +01:00
ar9342_ubnt_powerbeam-m2-xw.dts ath79: generic: rework ar9342_ubnt_xw dtsi, and add support for Ubiquiti LiteBeam M5 (XW), Ubiquiti AirGrid M5 HP (XW), Ubiquiti PowerBeam M5 300 (XW) 2024-01-20 19:57:57 +01:00
ar9342_ubnt_powerbeam-m5-xw.dts ath79: generic: rework ar9342_ubnt_xw dtsi, and add support for Ubiquiti LiteBeam M5 (XW), Ubiquiti AirGrid M5 HP (XW), Ubiquiti PowerBeam M5 300 (XW) 2024-01-20 19:57:57 +01:00
ar9342_ubnt_wa_1port.dtsi ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
ar9342_ubnt_wa_2port.dtsi ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
ar9342_ubnt_wa.dtsi ath79: convert ath10k calibration data to NVMEM (built-in MAC) 2024-02-01 17:09:02 +01:00
ar9342_ubnt_xw_rssileds.dtsi ath79: generic: rework ar9342_ubnt_xw dtsi, and add support for Ubiquiti LiteBeam M5 (XW), Ubiquiti AirGrid M5 HP (XW), Ubiquiti PowerBeam M5 300 (XW) 2024-01-20 19:57:57 +01:00
ar9342_ubnt_xw.dtsi ath79: generic: rework ar9342_ubnt_xw dtsi, and add support for Ubiquiti LiteBeam M5 (XW), Ubiquiti AirGrid M5 HP (XW), Ubiquiti PowerBeam M5 300 (XW) 2024-01-20 19:57:57 +01:00
ar9342_zyxel_nwa11xx.dtsi ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar9342_zyxel_nwa1100-nh.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9342_zyxel_nwa1121-ni.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9342_zyxel_nwa1123-ac.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9342_zyxel_nwa1123-ni.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_aerohive_hiveap-121.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_alfa-network_n5q.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_araknis_an-300-ap-i-n.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_atheros_db120.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_comfast_cf-e120a-v3.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_compex_wpj344-16m.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_devolo_dlan_wifi.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_devolo_dlan-pro-1200plus-ac.dts ath79: add support for Devolo dLAN pro 1200+ WiFi ac 2021-06-06 18:56:45 +02:00
ar9344_devolo_magic-2-wifi.dts ath79: add support for Devolo dLAN pro 1200+ WiFi ac 2021-06-06 18:56:45 +02:00
ar9344_dlink_dir-8x5.dtsi ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar9344_dlink_dir-825-c1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_dlink_dir-835-a1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_embeddedwireless_balin.dts ath79: drop redundant label with new LED color/function format 2024-02-07 14:48:34 +01:00
ar9344_engenius_eap600.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_engenius_ecb600.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_enterasys_ws-ap3705i.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_fortinet_ap-dual.dtsi ath79: fix pci_device_reg errors 2024-01-05 16:17:58 +01:00
ar9344_fortinet_fap-221-b.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_mercury_mw4530r-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_mikrotik_routerboard-16m-nor.dtsi ath79: mikrotik: stack ar9344 devices to single dtsi 2023-02-26 22:22:48 +01:00
ar9344_mikrotik_routerboard-911-lite.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_mikrotik_routerboard-951g-2hnd.dts ath79: DTS improvement for buzzer on RB951G-2HnD 2023-07-01 15:51:26 +02:00
ar9344_mikrotik_routerboard-951ui-2hnd.dts ath79: mikrotik: extract common bits for RB951x-2HnD devices 2023-06-25 13:18:31 +02:00
ar9344_mikrotik_routerboard-951x-2hnd.dtsi ath79: mikrotik: extract common bits for RB951x-2HnD devices 2023-06-25 13:18:31 +02:00
ar9344_mikrotik_routerboard-lhg-5nd.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_mikrotik_routerboard-sxt-5nd-r2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_mikrotik_routerboard.dtsi ath79: mikrotik: stack ar9344 devices to single dtsi 2023-02-26 22:22:48 +01:00
ar9344_moxa_awk-1137c.dts ath79: drop redundant label with new LED color/function format 2024-02-07 14:48:34 +01:00
ar9344_netgear_pgzng1.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar9344_netgear_r6100.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_netgear_wndr3700-v4.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_netgear_wndr4300.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_netgear_wndr4300sw.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_netgear_wndr4300tn.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_netgear_wndr_usb.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_netgear_wndr_wan.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_netgear_wndr.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_ocedo_raccoon.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_openmesh_mr600-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_openmesh_mr600-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_openmesh_mr600.dtsi ath79: ar: convert to mac-base 2023-11-25 21:34:18 -08:00
ar9344_openmesh_om5p-an.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_openmesh_om5p.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_pcs_cap324.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_pcs_cr5000.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_qihoo_c301.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_qxwlan_e750a-v4-8m.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_qxwlan_e750a-v4-16m.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_qxwlan_e750g-v8-8m.dts ath79: ar: convert to mac-base 2023-11-25 21:34:18 -08:00
ar9344_qxwlan_e750g-v8-16m.dts ath79: ar: convert to mac-base 2023-11-25 21:34:18 -08:00
ar9344_qxwlan_e750x.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_ruckus_zf7372.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_samsung_wam250.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_senao_ap-dual.dtsi ath79: fix pci_device_reg errors 2024-01-05 16:17:58 +01:00
ar9344_teltonika_rut9xx.dtsi ath79: ar: convert to mac-base 2023-11-25 21:34:18 -08:00
ar9344_teltonika_rut955-h7v3c0.dts ath79: ar: convert to mac-base 2023-11-25 21:34:18 -08:00
ar9344_teltonika_rut955.dts ath79: ar: convert to mac-base 2023-11-25 21:34:18 -08:00
ar9344_tplink_cpe210-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_cpe220-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_cpe510-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_cpe510-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_cpe510-v3.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_cpe605-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_tplink_cpe610-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_tplink_cpe610-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_tplink_cpe_1port.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_tplink_cpe_2port.dtsi ath79: remove redundant nvmem definitions 2021-08-20 18:13:55 +02:00
ar9344_tplink_cpe.dtsi ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar9344_tplink_tl-wdr3500-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_tplink_tl-wdr3600-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_tl-wdr4300-v1-il.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_tl-wdr4300-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_tl-wdr4300.dtsi ath79: ar: convert to mac-base 2023-11-25 21:34:18 -08:00
ar9344_tplink_tl-wdr4310-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_tl-wdrxxxx.dtsi ath79: ar: convert to mac-base 2023-11-25 21:34:18 -08:00
ar9344_tplink_tl-wr841hp-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_tplink_wbs210-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_wbs210-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_wbs510-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_wbs510-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_ubnt_unifi-ap-pro.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar9344_watchguard_ap100.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_watchguard_ap200.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_wd_mynet-n600.dts ath79: drop redundant label with new LED color/function format 2024-02-07 14:48:34 +01:00
ar9344_wd_mynet-n750.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_wd_mynet-nxxx.dtsi ath79: add support for WD My Net N600 2021-12-11 00:50:02 +01:00
ar9344_wd_mynet-wifi-rangeextender.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_winchannel_wb2000.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_zbtlink_zbt-wd323.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar9344.dtsi ath79: rename pcie-controller to pcie 2024-01-05 16:17:57 +01:00
arxxxx_fortinet_loader.dtsi ath79: fortinet-fap-220-b: convert to nvmem-layout 2023-11-27 00:34:49 +01:00
ath79.dtsi ath79: skip reset control for syscon devices 2024-05-09 23:53:02 +02:00
qca953x_dlink_dap-2xxx.dtsi ath79: qca: convert to nvmem-layout 2023-11-25 17:14:04 -08:00
qca953x_tplink_tl-wr810n.dtsi ath79: qca: remove mac-address-increment 2023-11-25 17:14:04 -08:00
qca953x.dtsi ath79: rename pcie-controller to pcie 2024-01-05 16:17:57 +01:00
qca955x_dlink_dap-2xxx.dtsi ath79: qca: convert to nvmem-layout 2023-11-25 17:14:04 -08:00
qca955x_elecom_wab.dtsi ath79: drop unnecessary &uart node from dtsi of QCA955x devices 2024-03-08 17:35:01 +01:00
qca955x_engenius_ecb1xxx.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca955x_senao_loader.dtsi ath79: fix pci_device_reg errors 2024-01-05 16:17:58 +01:00
qca955x_senao_router-dual.dtsi ath79: fix pci_device_reg errors 2024-01-05 16:17:58 +01:00
qca955x_ubnt_xc.dtsi ath79: convert ath10k calibration data to NVMEM (built-in MAC) 2024-02-01 17:09:02 +01:00
qca955x_zyxel_nbg6x16.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca955x.dtsi ath79: add aliases to qca955x.dtsi for uart0/1 2024-03-08 17:35:01 +01:00
qca956x.dtsi ath79: rename pcie-controller to pcie 2024-01-05 16:17:57 +01:00
qca9531_8dev_lima.dts ath79: qca: convert to nvmem-layout 2023-11-25 17:14:04 -08:00
qca9531_alcatel_hh40v.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_alfa-network_n2q.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_alfa-network_pi-wifi4.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_alfa-network_r36a.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_alfa-network_r36a.dtsi ath79: qca: remove mac-address-increment 2023-11-25 17:14:04 -08:00
qca9531_alfa-network_tube-2hq.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_asus_rp-ac51.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_comfast_cf-e5.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_comfast_cf-e130n-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_comfast_cf-e313ac.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_comfast_cf-e314n-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_comfast_cf-e560ac.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_comfast_cf-ew71-v2.dts ath79: add support for Comfast CF-EW71 v2 2024-04-14 19:20:06 +02:00
qca9531_comfast_cf-ew72.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_comfast_cf-wr752ac-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_compex_wpj531-16m.dts ath79: qca: convert to nvmem-layout 2023-11-25 17:14:04 -08:00
qca9531_dlink_dch-g020-a1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_engenius_ews511ap.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_glinet_gl-ar300m16.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9531_glinet_gl-ar300m-lite.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_glinet_gl-ar300m-nand.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9531_glinet_gl-ar300m-nor.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9531_glinet_gl-ar300m.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_glinet_gl-ar750.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_glinet_gl-e750.dts ath79: qca: convert to nvmem-layout 2023-11-25 17:14:04 -08:00
qca9531_glinet_gl-s200-nor-nand.dts ath79: add support for GL.iNet GL-S200 2023-10-31 13:53:11 +01:00
qca9531_glinet_gl-s200-nor.dts ath79: add support for GL.iNet GL-S200 2023-10-31 13:53:11 +01:00
qca9531_glinet_gl-s200.dtsi ath79: qca: convert to nvmem-layout 2023-11-25 17:14:04 -08:00
qca9531_glinet_gl-x300b.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_glinet_gl-x750.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_glinet_gl-xe300.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_joyit_jt-or750i.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_letv_lba-047-ch.dts ath79: drop redundant label with new LED color/function format 2024-02-07 14:48:34 +01:00
qca9531_mikrotik_routerboard-951ui-2nd.dts ath79: add support for MikroTik hAP (RB951Ui-2nD) 2022-05-21 13:54:08 +02:00
qca9531_qxwlan_e600g-v2-8m.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_qxwlan_e600g-v2-16m.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_qxwlan_e600g.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_qxwlan_e600gac-v2-8m.dts ath79: add support for Qxwlan E600G v2 / E600GAC v2 2020-11-12 17:18:26 +01:00
qca9531_qxwlan_e600gac-v2-16m.dts ath79: add support for Qxwlan E600G v2 / E600GAC v2 2020-11-12 17:18:26 +01:00
qca9531_telco_t1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_teltonika_rut300.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_tplink_archer-d50-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_tplink_tl-mr3420-v3.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_tplink_tl-mr6400-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_tplink_tl-wr810n-v1.dts ath79: gpio to gpios 2024-01-05 16:17:58 +01:00
qca9531_tplink_tl-wr902ac-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_wallys_dr531.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_yuncore_a770.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_comfast_cf-e110n-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_dlink_dap-13xx.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_dlink_dap-1330-a1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_dlink_dap-1365-a1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_dlink_dap-2230-a1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_dlink_dap-3320-a1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_kuwfi_c910.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_mikrotik_routerboard-16m.dtsi ath79: add support for MikroTik RouterBOARD 750 r2 (hEX lite) 2023-09-16 12:49:26 +02:00
qca9533_mikrotik_routerboard-95x.dtsi ath79: add support for MikroTik RouterBOARD 750 r2 (hEX lite) 2023-09-16 12:49:26 +02:00
qca9533_mikrotik_routerboard-750-r2.dts ath79: add support for MikroTik RouterBOARD 750 r2 (hEX lite) 2023-09-16 12:49:26 +02:00
qca9533_mikrotik_routerboard-952ui-5ac2nd.dts ath79: add support for MikroTik RouterBOARD hAP ac lite 2022-05-21 13:54:02 +02:00
qca9533_mikrotik_routerboard-lhg-2nd.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_mikrotik_routerboard-lhg-hb.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_mikrotik_routerboard-map-2nd.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_mikrotik_routerboard-mapl-2nd.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_mikrotik_routerboard-wap-2nd.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_mikrotik_routerboard-wapr-2nd.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_openmesh_om2p-hs-v4.dts ath79: Add support for OpenMesh OM2P-HS v4 2020-12-28 19:37:24 +01:00
qca9533_openmesh_om2p-v4.dts ath79: Add support for OpenMesh OM2P v4 2020-12-28 19:37:24 +01:00
qca9533_openmesh_om2p-v4.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_plasmacloud_pa300.dts ath79: Add support for Plasma Cloud PA300 2020-12-22 19:11:50 +01:00
qca9533_plasmacloud_pa300.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_plasmacloud_pa300e.dts ath79: Add support for Plasma Cloud PA300E 2020-12-22 19:11:50 +01:00
qca9533_qca_ap143-8m.dts ath79: qca: convert to nvmem-layout 2023-11-25 17:14:04 -08:00
qca9533_qca_ap143-16m.dts ath79: qca: convert to nvmem-layout 2023-11-25 17:14:04 -08:00
qca9533_qca_ap143.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_tplink_cpe210-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_cpe210-v3.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_cpe210.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_tplink_cpe220-v3.dts ath79: remove redundant nvmem definitions 2021-08-20 18:13:55 +02:00
qca9533_tplink_cpexxx.dtsi ath79: fix avoid_unnecessary_addr_size warnings 2024-01-05 16:17:57 +01:00
qca9533_tplink_tl-wa801nd-v3.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wa801nd-v4.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wa801nd.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_tplink_tl-wa850re-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_tplink_tl-wr802n-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wr802n-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wr802n.dtsi ath79: qca: remove mac-address-increment 2023-11-25 17:14:04 -08:00
qca9533_tplink_tl-wr810n-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wr841-v9.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wr841-v10.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wr841-v11.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wr841-v11.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_tplink_tl-wr841-v12.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wr841.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_tplink_tl-wr841hp-v3.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_tplink_tl-wr842n-v3.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_ubnt_aircube-isp.dts ath79: qca: convert to nvmem-layout 2023-11-25 17:14:04 -08:00
qca9533_yuncore_a930.dts ath79: qca: convert to nvmem-layout 2023-11-25 17:14:04 -08:00
qca9550_airtight_c-75.dts ath79: drop redundant label with new LED color/function format 2024-02-07 14:48:34 +01:00
qca9550_huawei_ap5030dn.dts ath79: add support for Huawei AP5030DN 2024-03-31 18:09:43 +02:00
qca9556_avm_fritz450e.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9556_avm_fritz1750e.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9556_avm_fritz-repeater.dtsi ath79: convert ath10k calibration data to NVMEM (built-in MAC) 2024-02-01 17:09:02 +01:00
qca9556_avm_fritzdvbc.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9556_mikrotik_routerboard-wap-g-5hact2hnd.dts ath79: add aliases to qca955x.dtsi for uart0/1 2024-03-08 17:35:01 +01:00
qca9557_8dev_rambutan.dts ath79: qca: convert to nvmem-layout 2023-11-25 17:14:04 -08:00
qca9557_araknis_an-500-ap-i-ac.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9557_buffalo_bhr-4grv2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9557_dlink_dap-2660-a1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9557_dongwon_dw02-412h-64m.dts ath79: improve support for Dongwon T&I DW02-412H 2022-02-01 14:54:16 +09:00
qca9557_dongwon_dw02-412h-128m.dts ath79: improve support for Dongwon T&I DW02-412H 2022-02-01 14:54:16 +09:00
qca9557_dongwon_dw02-412h.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9557_elecom_wab-s600-ps.dts ath79: add support for ELECOM WAB-S600-PS 2024-03-02 14:08:08 +01:00
qca9557_elecom_wab-s1167-ps.dts ath79: add support for ELECOM WAB-S1167-PS 2024-03-02 14:08:08 +01:00
qca9557_engenius_eap1200h.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9557_engenius_ecb1200.dts ath79: create common DTSI for ECB1200 and ECB1750 2020-12-22 19:11:50 +01:00
qca9557_engenius_enstationac-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9557_engenius_esr1200.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9557_extreme-networks_ws-ap3805i.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9557_iodata_wn-ac1167dgr.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9557_iodata_wn-ac1600dgr2.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9557_iodata_wn-ac1600dgr.dts ath79: convert ath10k calibration data to NVMEM (ASCII MAC) 2024-02-01 17:09:03 +01:00
qca9557_iodata_wn-ac-dgr.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9557_meraki_mr18.dts ath79: drop unnecessary &uart node from dtsi of QCA955x devices 2024-03-08 17:35:01 +01:00
qca9557_zyxel_nbg6616.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_allnet_all-wap02860ac.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_araknis_an-700-ap-i-ac.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_aruba_ap-115.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_belkin_f9j1108-v2.dts ath79: create shared DTSI/definition for Belkin F9J1108/F9K1115 v2 2020-12-14 16:57:21 +01:00
qca9558_belkin_f9k1115-v2.dts ath79: add support for the Belkin F9K1115 v2 (AC1750 DB Wi-Fi) 2020-12-14 16:59:49 +01:00
qca9558_belkin_f9x-v2.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_comfast_cf-e380ac-v2.dts ath79: add aliases to qca955x.dtsi for uart0/1 2024-03-08 17:35:01 +01:00
qca9558_comfast_cf-wr650ac-v1.dts ath79: convert ath10k calibration data to NVMEM (built-in MAC) 2024-02-01 17:09:02 +01:00
qca9558_comfast_cf-wr650ac-v2.dts ath79: convert ath10k calibration data to NVMEM (built-in MAC) 2024-02-01 17:09:02 +01:00
qca9558_comfast_cf-wr650ac.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_compex_wpj558-16m.dts ath79: qca: convert to nvmem-layout 2023-11-25 17:14:04 -08:00
qca9558_devolo_dvl1xxx.dtsi ath79: convert ath10k calibration data to NVMEM (binary MAC) 2024-02-01 17:09:02 +01:00
qca9558_devolo_dvl1200e.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_devolo_dvl1200i.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_devolo_dvl1750c.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_devolo_dvl1750e.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_devolo_dvl1750i.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_devolo_dvl1750x.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_dlink_dap-2680-a1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_dlink_dap-2695-a1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_dlink_dap-3662-a1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_dlink_dir-629-a1.dts ath79: add aliases to qca955x.dtsi for uart0/1 2024-03-08 17:35:01 +01:00
qca9558_domywifi_dw33d.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_elecom_wab-i1750-ps.dts ath79: register all ttys as Linux console for ELECOM WAB-I1750-PS 2024-03-24 21:10:59 +01:00
qca9558_engenius_dual_ap.dtsi ath79: add support for Senao Engenius ENS1750 2024-05-11 16:57:28 +02:00
qca9558_engenius_eap1750h.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_engenius_ecb1750.dts ath79: create common DTSI for ECB1200 and ECB1750 2020-12-22 19:11:50 +01:00
qca9558_engenius_ens1750.dts ath79: add support for Senao Engenius ENS1750 2024-05-11 16:57:28 +02:00
qca9558_engenius_epg5000.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_engenius_esr900.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_engenius_esr1750.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_engenius_ews660ap.dts ath79: add support for Senao Engenius ENS1750 2024-05-11 16:57:28 +02:00
qca9558_jjplus_jwap230.dts ath79: drop redundant label with new LED color/function format 2024-02-07 14:48:34 +01:00
qca9558_librerouter_librerouter-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_linksys_ea4500-v3.dts ath79: qca: convert to nvmem-layout 2023-11-25 17:14:04 -08:00
qca9558_mikrotik_routerboard-92x.dtsi ath79: add aliases to qca955x.dtsi for uart0/1 2024-03-08 17:35:01 +01:00
qca9558_mikrotik_routerboard-96x.dtsi ath79: add aliases to qca955x.dtsi for uart0/1 2024-03-08 17:35:01 +01:00
qca9558_mikrotik_routerboard-911g-5hpacd.dts ath79: support MikroTik RouterBOARD 911G-5HPacD 2024-01-07 01:19:56 +01:00
qca9558_mikrotik_routerboard-921gs-5hpacd-15s.dts ath79: support MikroTik RouterBOARD 911G-5HPacD 2024-01-07 01:19:56 +01:00
qca9558_mikrotik_routerboard-922uags-5hpacd.dts ath79: support MikroTik RouterBOARD 911G-5HPacD 2024-01-07 01:19:56 +01:00
qca9558_mikrotik_routerboard-962uigs-5hact2hnt.dts ath79: add support for MikroTik RouterBOARD 962UiGS-5HacT2HnT (hAP ac) 2022-04-16 16:59:29 +02:00
qca9558_netgear_ex7300.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_ocedo_koala.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_ocedo_ursus.dts ath79: convert ath10k calibration data to NVMEM (binary MAC) 2024-02-01 17:09:02 +01:00
qca9558_openmesh_a40.dts ath79: Add support for OpenMesh A40 2021-06-05 01:17:11 +02:00
qca9558_openmesh_a60.dts ath79: Add support for OpenMesh A60 2021-06-05 01:17:11 +02:00
qca9558_openmesh_a60.dtsi ath79: add aliases to qca955x.dtsi for uart0/1 2024-03-08 17:35:01 +01:00
qca9558_openmesh_mr900-v1.dts ath79: convert ath10k calibration data to NVMEM (binary MAC) 2024-02-01 17:09:02 +01:00
qca9558_openmesh_mr900-v2.dts ath79: convert ath10k calibration data to NVMEM (binary MAC) 2024-02-01 17:09:02 +01:00
qca9558_openmesh_mr1750-v1.dts ath79: Add support for OpenMesh MR1750 v1 2021-01-19 21:41:26 +01:00
qca9558_openmesh_mr1750-v2.dts ath79: Add support for OpenMesh MR1750 v2 2021-01-19 21:41:26 +01:00
qca9558_openmesh_mr.dtsi ath79: add aliases to qca955x.dtsi for uart0/1 2024-03-08 17:35:01 +01:00
qca9558_openmesh_om5p-ac-v1.dts ath79: add aliases to qca955x.dtsi for uart0/1 2024-03-08 17:35:01 +01:00
qca9558_openmesh_om5p-ac-v2.dts ath79: add aliases to qca955x.dtsi for uart0/1 2024-03-08 17:35:01 +01:00
qca9558_qxwlan_e558-v2-8m.dts ath79: add support for Qxwlan E558 v2 2020-10-17 20:17:59 +02:00
qca9558_qxwlan_e558-v2-16m.dts ath79: add support for Qxwlan E558 v2 2020-10-17 20:17:59 +02:00
qca9558_qxwlan_e558.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_sitecom_wlr-8100.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_sophos_ap15.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_sophos_ap55.dts ath79: add support for Sophos AP100/AP55 family 2022-04-16 16:59:29 +02:00
qca9558_sophos_ap55c.dts ath79: add support for Sophos AP100/AP55 family 2022-04-16 16:59:29 +02:00
qca9558_sophos_ap100.dts ath79: add support for Sophos AP100/AP55 family 2022-04-16 16:59:29 +02:00
qca9558_sophos_ap100c.dts ath79: add support for Sophos AP100/AP55 family 2022-04-16 16:59:29 +02:00
qca9558_sophos_ap.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_tplink_archer-c5-v1.dts ath79: convert ath10k calibration data to NVMEM (binary MAC) 2024-02-01 17:09:02 +01:00
qca9558_tplink_archer-c7-v1.dts ath79: qca: remove mac-address-increment 2023-11-25 17:14:04 -08:00
qca9558_tplink_archer-c7-v2.dts ath79: qca: remove mac-address-increment 2023-11-25 17:14:04 -08:00
qca9558_tplink_archer-c.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9558_tplink_archer-d7-v1.dts ath79: convert ath10k calibration data to NVMEM (binary MAC) 2024-02-01 17:09:02 +01:00
qca9558_tplink_archer-d7.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_tplink_archer-d7b-v1.dts ath79: convert ath10k calibration data to NVMEM (binary MAC) 2024-02-01 17:09:02 +01:00
qca9558_tplink_re350k-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_tplink_re355-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9558_tplink_re450-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9558_tplink_rex5x.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_tplink_tl-wdr4900-v2.dts ath79: qca: remove mac-address-increment 2023-11-25 17:14:04 -08:00
qca9558_tplink_tl-wdr7500-v3.dts ath79: convert ath10k calibration data to NVMEM (binary MAC) 2024-02-01 17:09:02 +01:00
qca9558_tplink_tl-wr941n-v7-cn.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_tplink_tl-wr1043nd-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9558_tplink_tl-wr1043nd-v3.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9558_tplink_tl-wr1043nd.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_tplink_tl-wr1045nd-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9558_trendnet_tew-823dru.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_ubnt_nanobeam-ac-xc.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_ubnt_powerbeam-5ac-500.dts ath79: qca: convert to nvmem-layout 2023-11-25 17:14:04 -08:00
qca9558_ubnt_rocket-5ac-lite.dts ath79: qca: convert to nvmem-layout 2023-11-25 17:14:04 -08:00
qca9558_watchguard_ap300.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_zyxel_emg2926_q10a.dts ath79: add Zyxel EMG2926-Q10A 2022-02-26 13:36:30 +01:00
qca9558_zyxel_nbg6716.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9561_avm_fritz4020.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9561_nec_wf1200cr.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9561_tplink_archer-c5x.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9561_tplink_archer-c6x.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9561_tplink_archer-c25-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9561_tplink_archer-c58-v1.dts ath79: convert ath10k pre-calibration data to NVMEM (binary MAC) 2024-02-01 17:09:02 +01:00
qca9561_tplink_archer-c59-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9561_tplink_archer-c59-v2.dts ath79: convert ath10k pre-calibration data to NVMEM (binary MAC) 2024-02-01 17:09:02 +01:00
qca9561_tplink_archer-c60-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9561_tplink_archer-c60-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9561_tplink_archer-c60-v3.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9561_tplink_eap225-wall-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9561_tplink_tl-wdr6500-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9561_xiaomi_mi-router-4q.dts ath79: qca: remove mac-address-increment 2023-11-25 17:14:04 -08:00
qca9563_asus_pl-ac56.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_asus_rp-ac66.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_comfast_cf-e375ac.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_compex_wpj563.dts ath79: qca: convert to nvmem-layout 2023-11-25 17:14:04 -08:00
qca9563_dlink_covr-c1200-a1.dts ath79: add support for D-Link COVR-C1200 A1 2024-03-09 20:00:11 +01:00
qca9563_dlink_covr-p2500-a1.dts ath79: split dtsi for D-Link COVR-P2500 2024-03-09 20:00:11 +01:00
qca9563_dlink_covr.dtsi ath79: split dtsi for D-Link COVR-P2500 2024-03-09 20:00:11 +01:00
qca9563_dlink_dap-1720-a1.dts ath79: add support for D-link DAP-1720 A1 2023-11-26 18:27:35 +01:00
qca9563_dlink_dir-8x9-a1.dtsi ath79: qca: convert to nvmem-layout 2023-11-25 17:14:04 -08:00
qca9563_dlink_dir-842-c1.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9563_dlink_dir-842-c2.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9563_dlink_dir-842-c3.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9563_dlink_dir-842-c.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_dlink_dir-859-a1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_dlink_dir-859-a3.dts ath79: drop redundant label with new LED color/function format 2024-02-07 14:48:34 +01:00
qca9563_dlink_dir-869-a1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_elecom_wrc-300ghbk2-i.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_elecom_wrc-1750ghbk2-i.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_elecom_wrc-ghbk2-i.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_glinet_gl-ar750s-nor-nand.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9563_glinet_gl-ar750s-nor.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9563_glinet_gl-ar750s.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_glinet_gl-x1200-nor-nand.dts ath79: add support for GL.iNet GL-X1200 2023-02-25 14:31:42 +01:00
qca9563_glinet_gl-x1200-nor.dts ath79: add support for GL.iNet GL-X1200 2023-02-25 14:31:42 +01:00
qca9563_glinet_gl-x1200.dtsi ath79: qca: convert to nvmem-layout 2023-11-25 17:14:04 -08:00
qca9563_nec_wg800hp.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_nec_wg1200cr.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_netgear_wndr4300-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_netgear_wndr4500-v3.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9563_netgear_wndr.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_phicomm_k2t.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_qxwlan_e1700ac-v2-8m.dts ath79: add support for Qxwlan E1700AC v2 2020-10-17 20:18:00 +02:00
qca9563_qxwlan_e1700ac-v2-16m.dts ath79: add support for Qxwlan E1700AC v2 2020-10-17 20:18:00 +02:00
qca9563_qxwlan_e1700ac.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_rosinson_wr818.dts ath79: qca: convert to nvmem-layout 2023-11-25 17:14:04 -08:00
qca9563_tplink_archer-a7-v5.dts ath79: convert ath10k calibration data to NVMEM (binary MAC) 2024-02-01 17:09:02 +01:00
qca9563_tplink_archer-c2-v3.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_archer-c6-v2-us.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_archer-c6-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_archer-c7-v4.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_archer-c7-v5.dts ath79: convert ath10k calibration data to NVMEM (binary MAC) 2024-02-01 17:09:02 +01:00
qca9563_tplink_archer-x6-v2.dtsi ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9563_tplink_archer-x7-v5.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_cpe710-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_deco-m4r-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_deco-s4-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_eap2x5-1port.dtsi ath79: fix mac address on eap2x5-1port devices 2024-01-23 10:41:20 +01:00
qca9563_tplink_eap225-outdoor-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_eap225-outdoor-v3.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_eap225-v1.dts ath79: drop redundant label with new LED color/function format 2024-02-07 14:48:34 +01:00
qca9563_tplink_eap225-v3.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_eap225-v4.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_eap245-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_eap245-v3.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_re450-v2.dts ath79: convert ath10k calibration data to NVMEM (binary MAC) 2024-02-01 17:09:02 +01:00
qca9563_tplink_re450-v3.dts ath79: convert ath10k calibration data to NVMEM (binary MAC) 2024-02-01 17:09:02 +01:00
qca9563_tplink_re450.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_re455-v1.dts ath79: convert ath10k calibration data to NVMEM (binary MAC) 2024-02-01 17:09:02 +01:00
qca9563_tplink_tl-wa1201-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_tl-wpa8630-v1.dts ath79: convert ath10k calibration data to NVMEM (binary MAC) 2024-02-01 17:09:02 +01:00
qca9563_tplink_tl-wpa8630.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_tl-wpa8630p-v2-int.dts ath79: convert ath10k pre-calibration data to NVMEM (binary MAC) 2024-02-01 17:09:02 +01:00
qca9563_tplink_tl-wpa8630p-v2.0-eu.dts ath79: convert ath10k pre-calibration data to NVMEM (binary MAC) 2024-02-01 17:09:02 +01:00
qca9563_tplink_tl-wpa8630p-v2.1-eu.dts ath79: convert ath10k pre-calibration data to NVMEM (binary MAC) 2024-02-01 17:09:02 +01:00
qca9563_tplink_tl-wr1043n-v5.dts ath79: qca: convert to nvmem-layout 2023-11-25 17:14:04 -08:00
qca9563_tplink_tl-wr1043n.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_tl-wr1043nd-v4.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_ubnt_uk-ultra.dts ath79: add support for UniFi UK-Ultra 2024-01-07 23:06:17 +01:00
qca9563_ubnt_unifiac-lite.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9563_ubnt_unifiac-lite.dtsi ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9563_ubnt_unifiac-lr.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9563_ubnt_unifiac-mesh-pro.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9563_ubnt_unifiac-mesh.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9563_ubnt_unifiac-pro.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9563_ubnt_unifiac-pro.dtsi ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9563_ubnt_unifiac.dtsi ath79: convert ath10k calibration data to NVMEM (built-in MAC) 2024-02-01 17:09:02 +01:00
qca9563_xiaomi_aiot-ac2350.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_yuncore_a782.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9563_yuncore_xd3200.dts ath79: convert ath10k calibration data to NVMEM (built-in MAC) 2024-02-01 17:09:02 +01:00
qca9563_yuncore_xd4200.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9563_yuncore_xd4200.dtsi ath79: convert ath10k calibration data to NVMEM (built-in MAC) 2024-02-01 17:09:02 +01:00
qca9563_zte_mf28x.dtsi ath79: refactor ZTE MF28x dts files 2023-05-06 20:59:46 +02:00
qca9563_zte_mf281.dts ath79: drop redundant label with new LED color/function format 2024-02-07 14:48:34 +01:00
qca9563_zte_mf282.dts ath79: drop redundant label with new LED color/function format 2024-02-07 14:48:34 +01:00
qca9563_zte_mf286.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_zte_mf286.dtsi ath79: refactor ZTE MF28x dts files 2023-05-06 20:59:46 +02:00
qca9563_zte_mf286a.dts ath79: support ZTE MF286A/R 2022-02-26 17:46:10 +01:00
qca9563_zte_mf286ar.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_zte_mf286r.dts ath79: support ZTE MF286A/R 2022-02-26 17:46:10 +01:00
qcn5502_asus_rt-ac59u-v2.dts ath79: add support for ASUS RT-AC59U / ZenWiFi CD6 2023-07-08 20:19:00 +02:00
qcn5502_asus_rt-ac59u.dts ath79: add support for ASUS RT-AC59U / ZenWiFi CD6 2023-07-08 20:19:00 +02:00
qcn5502_asus_rt-ac59u.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qcn5502_asus_zenwifi-cd6.dtsi ath79: add support for ASUS RT-AC59U / ZenWiFi CD6 2023-07-08 20:19:00 +02:00
qcn5502_asus_zenwifi-cd6n.dts ath79: add support for ASUS RT-AC59U / ZenWiFi CD6 2023-07-08 20:19:00 +02:00
qcn5502_asus_zenwifi-cd6r.dts ath79: add support for ASUS RT-AC59U / ZenWiFi CD6 2023-07-08 20:19:00 +02:00
qcn5502_asus.dtsi ath79: qcn: convert to nvmem-layout 2023-11-25 19:43:32 -08:00
qcn5502_netgear_ex7300-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qcn5502_tplink_archer-a9-v6.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
tp9343_tplink_tl-wa901nd-v4.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
tp9343_tplink_tl-wa901nd-v5.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
tp9343_tplink_tl-wa901nd.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
tp9343_tplink_tl-wr94x.dtsi ath79: add support for TP-Link TL-WA901ND v4 and v5 2020-05-18 13:35:38 +02:00
tp9343_tplink_tl-wr940n-v3.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
tp9343_tplink_tl-wr940n-v3.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
tp9343_tplink_tl-wr940n-v4.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
tp9343_tplink_tl-wr940n-v6.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
tp9343_tplink_tl-wr941hp-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
tp9343_tplink_tl-wr941nd-v6.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
tp9343_tplink_tl-wx.dtsi ath79: tp9343: convert to nvmem-layout 2023-11-25 19:43:35 -08:00