fish/immortalwrt
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
46f4d99cf6
immortalwrt/target/linux/ramips/dts
History
Jonathan Sturges 46f4d99cf6 ramips: add support for Amped Wireless ALLY router and extender 
Amped Wireless ALLY is a whole-home WiFi kit, with a router (model
ALLY-R1900K) and an Extender (model ALLY-00X19K).  Both are devices are
11ac and based on MediaTek MT7621AT and MT7615N chips.  The units are
nearly identical, except the Extender lacks a USB port and has a single
Ethernet port.

Specification:
- SoC: MediaTek MT7621AT (2C/4T) @ 880MHz
- RAM: 128MB DDR3 (Nanya NT5CC64M16GP-DI)
- FLASH: 128MB NAND (Winbond W29N01GVSIAA)
- WiFi: 2.4/5 GHz 4T4R
  - 2.4GHz MediaTek MT7615N bgn
  - 5GHz MediaTek MT7615N nac
- Switch: SoC integrated Gigabit Switch
- USB: 1x USB3 (Router only)
- BTN: Reset, WPS
- LED: single RGB
- UART:  through-hole on PCB.
   J1: pin1 (square pad, towards rear)=3.3V, pin2=RX,
   pin3=GND, pin4=TX.  Settings: 57600/8N1.

Note regarding dual system partitions
-------------------------------------

The vendor firmware and boot loader use a dual partition scheme.  The boot
partition is decided by the bootImage U-boot environment variable: 0 for
the 1st partition, 1 for the 2nd.

OpenWrt does not support this scheme and will always use the first OS
partition.  It will set bootImage to 0 during installation, making sure
the first partition is selected by the boot loader.

Also, because we can't be sure which partition is active to begin with, a
2-step flash process is used.  We first flash an initramfs image, then
follow with a regular sysupgrade.

Installation:

Router (ALLY-R1900K)
1) Install the flashable initramfs image via the OEM web-interface.
  (Alternatively, you can use the TFTP recovery method below.)
  You can use WiFi or Ethernet.
  The direct URL is:  http://192.168.3.1/07_06_00_firmware.html
  a. No login is needed, and you'll be in their setup wizard.
  b. You might get a warning about not being connected to the Internet.
  c. Towards the bottom of the page will be a section entitled "Or
  Manually Upgrade Firmware from a File:" where you can manually choose
  and upload a firmware file.
  d: Click "Choose File", select the OpenWRT "initramfs" image and click
  "Upload."
2) The Router will flash the OpenWrt initramfs image and reboot.  After
  booting, LuCI will be available on 192.168.1.1.
3) Log into LuCI as root; there is no password.
4) Optional (but recommended) is to backup the OEM firmware before
  continuing; see process below.
5) Complete the Installation by flashing a full OpenWRT image.  Note:
  you may use the sysupgrade command line tool in lieu of the UI if
  you prefer.
  a.  Choose System -> Backup/Flash Firmware.
  b.  Click "Flash Image..." under "Flash new firmware image"
  c.  Click "Browse..." and then select the sysupgrade file.
  d.  Click Upload to upload the sysupgrade file.
  e.  Important:  uncheck "Keep settings and retain the current
      configuration" for this initial installation.
  f.  Click "Continue" to flash the firmware.
  g.  The device will reboot and OpenWRT is installed.

Extender (ALLY-00X19K)
1) This device requires a TFTP recovery procedure to do an initial load
  of OpenWRT.  Start by configuring a computer as a TFTP client:
  a. Install a TFTP client (server not necessary)
  b. Configure an Ethernet interface to 192.168.1.x/24; don't use .1 or .6
  c. Connect the Ethernet to the sole Ethernet port on the X19K.
2) Put the ALLY Extender in TFTP recovery mode.
  a. Do this by pressing and holding the reset button on the bottom while
  connecting the power.
  b. As soon as the LED lights up green (roughly 2-3 seconds), release
  the button.
3) Start the TFTP transfer of the Initramfs image from your setup machine.
For example, from Linux:
tftp -v -m binary 192.168.1.6 69 -c put initramfs.bin
4) The Extender will flash the OpenWrt initramfs image and reboot.  After
booting, LuCI will be available on 192.168.1.1.
5) Log into LuCI as root; there is no password.
6) Optional (but recommended) is to backup the OEM firmware before
  continuing; see process below.
7) Complete the Installation by flashing a full OpenWRT image.  Note: you
may use the sysupgrade command line tool in lieu of the UI if you prefer.
  a.  Choose System -> Backup/Flash Firmware.
  b.  Click "Flash Image..." under "Flash new firmware image"
  c.  Click "Browse..." and then select the sysupgrade file.
  d.  Click Upload to upload the sysupgrade file.
  e.  Important:  uncheck "Keep settings and retain the current
      configuration" for this initial installation.
  f.  Click "Continue" to flash the firmware.
  g.  The device will reboot and OpenWRT is installed.

Backup the OEM Firmware:
-----------------------

There isn't any downloadable firmware for the ALLY devices on the Amped
Wireless web site. Reverting back to the OEM firmware is not possible
unless we have a backup of the original OEM firmware.

The OEM firmware may be stored on either /dev/mtd3 ("firmware") or
/dev/mtd6 ("oem").  We can't be sure which was overwritten with the
initramfs image, so backup both partitions to be safe.

  1) Once logged into LuCI, navigate to System -> Backup/Flash Firmware.
  2) Under "Save mtdblock contents," first select "firmware" and click
  "Save mtdblock" to download the image.
  3) Repeat the process, but select "oem" from the pull-down menu.

Revert to the OEM Firmware:
--------------------------
* U-boot TFTP:
  Follow the TFTP recovery steps for the Extender, and use the
  backup image.

* OpenWrt "Flash Firmware" interface:
  Upload the backup image and select "Force update"
  before continuing.

Signed-off-by: Jonathan Sturges <jsturges@redhat.com>
2021-06-06 23:25:05 +08:00
..
mt7620a_aigale_ai-br100.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_alfa-network_ac1200rm.dts ramips: replace full-text licenses by SPDX identifier 2021-02-06 12:12:04 +08:00
mt7620a_alfa-network_r36m-e4g.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_alfa-network_tube-e4g.dts ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
mt7620a_asus_rp-n53.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_asus_rt-ac5x.dtsi ramips: remove model name from LED labels 2020-11-21 19:29:29 +08:00
mt7620a_asus_rt-ac51u.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_asus_rt-ac54u.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_bdcom_wap2100-sk.dts ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
mt7620a_buffalo_whr-300hp2.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_buffalo_whr-600d.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_buffalo_whr-1166d.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_cameo_810.dtsi treewide: add space before SPDX identifier 2020-11-28 19:03:27 +08:00
mt7620a_dlink_dch-m225.dts ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
mt7620a_dlink_dir-510l.dts ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
mt7620a_dlink_dir-810l.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_dlink_dwr-118-a1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_dlink_dwr-118-a2.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_dlink_dwr-960.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_dovado_tiny-ac.dts ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
mt7620a_edimax_br-6478ac-v2.dts ramips: replace full-text licenses by SPDX identifier 2021-02-06 12:12:04 +08:00
mt7620a_edimax_ew-747x.dtsi kernel: mtdsplit_uimage: replace "edimax, uimage" parser 2021-01-23 12:19:11 +08:00
mt7620a_edimax_ew-7476rpc.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_edimax_ew-7478ac.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_edimax_ew-7478apc.dts kernel: mtdsplit_uimage: replace "edimax, uimage" parser 2021-01-23 12:19:11 +08:00
mt7620a_engenius_esr600.dts ramips: do not enable unused GPIO controllers 2020-12-18 11:39:28 +08:00
mt7620a_fon_fon2601.dts kernel: mtdsplit_uimage: replace "fonfxc" and "sge" parsers 2021-01-23 12:14:20 +08:00
mt7620a_glinet_gl-mt300a.dts ramips: do not enable unused GPIO controllers 2020-12-18 11:39:28 +08:00
mt7620a_glinet_gl-mt300n.dts ramips: do not enable unused GPIO controllers 2020-12-18 11:39:28 +08:00
mt7620a_glinet_gl-mt750.dts ramips: do not enable unused GPIO controllers 2020-12-18 11:39:28 +08:00
mt7620a_head-weblink_hdrm200.dts ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
mt7620a_hiwifi_hc5x61.dtsi ramips: increase SPI frequency for HIWIFI HC5x61 devices 2021-03-23 11:16:06 +08:00
mt7620a_hiwifi_hc5661.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_hiwifi_hc5761.dts ramips: improve GPIO pin control for HC5x61 2021-03-20 11:23:11 +08:00
mt7620a_hiwifi_hc5861.dts ramips: improve GPIO pin control for HC5x61 2021-03-20 11:23:11 +08:00
mt7620a_hnet_c108.dts ramips: replace full-text licenses by SPDX identifier 2021-02-06 12:12:04 +08:00
mt7620a_iodata_wn-ac733gr3.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_iodata_wn-ac1167gr.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_iptime_a104ns.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_iptime_a1004ns.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_iptime.dtsi ramips: sync upstream source code 2020-04-19 12:29:05 +08:00
mt7620a_kimax_u25awf-h1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_lava_lr-25g001.dts ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
mt7620a_lb-link_bl-w1200.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_lenovo_newifi-y1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_lenovo_newifi-y1.dtsi ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
mt7620a_lenovo_newifi-y1s.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_linksys_e1700.dts ramips: replace full-text licenses by SPDX identifier 2021-02-06 12:12:04 +08:00
mt7620a_microduino_microwrt.dts ramips: do not enable unused GPIO controllers 2020-12-18 11:39:28 +08:00
mt7620a_netgear_ex3x00_ex61xx.dtsi ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
mt7620a_netgear_ex2700_wn3000rp-v3.dtsi ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_netgear_ex2700.dts ramips: replace full-text licenses by SPDX identifier 2021-02-06 12:12:04 +08:00
mt7620a_netgear_ex3700.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_netgear_ex6120.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_netgear_ex6130.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_netgear_wn3000rp-v3.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_netis_wf2770.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_ohyeah_oy-0001.dts ramips: do not enable unused GPIO controllers 2020-12-18 11:39:28 +08:00
mt7620a_phicomm_k2g.dts ramips: create shared DTSI for MT7620 Phicomm K2x series devices 2021-03-23 11:16:57 +08:00
mt7620a_phicomm_k2x.dtsi ramips: create shared DTSI for MT7620 Phicomm K2x series devices 2021-03-23 11:16:57 +08:00
mt7620a_phicomm_psg1208.dts ramips: increase SPI frequency for Phicomm series devices 2021-03-23 11:16:28 +08:00
mt7620a_phicomm_psg1218a.dts ramips: create shared DTSI for MT7620 Phicomm K2x series devices 2021-03-23 11:16:57 +08:00
mt7620a_phicomm_psg1218b.dts ramips: create shared DTSI for MT7620 Phicomm K2x series devices 2021-03-23 11:16:57 +08:00
mt7620a_planex_cs-qr10.dts ramips: do not enable unused GPIO controllers 2020-12-18 11:39:28 +08:00
mt7620a_planex_db-wrt01.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_planex_mzk-750dhp.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_planex_mzk-ex300np.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_planex_mzk-ex750np.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_ralink_mt7620a-evb.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_ralink_mt7620a-mt7530-evb.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_ralink_mt7620a-mt7610e-evb.dts ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
mt7620a_ralink_mt7620a-v22sg-evb.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_sanlinking_d240.dts ramips: replace full-text licenses by SPDX identifier 2021-02-06 12:12:04 +08:00
mt7620a_sercomm_na930.dts ramips: do not enable unused GPIO controllers 2020-12-18 11:39:28 +08:00
mt7620a_tplink_archer-c2-v1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_tplink_archer-c5-v4.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_tplink_archer-c20-v1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_tplink_archer-c20i.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_tplink_archer-c50-v1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_tplink_archer-mr200.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_tplink_archer.dtsi ramips: increase SPI frequency for MT7620 Archer 2020-07-23 22:47:48 +08:00
mt7620a_tplink_re2x0-v1.dtsi ramips: sync upstream source code (#3805) 2020-03-15 19:14:19 +08:00
mt7620a_tplink_re200-v1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_tplink_re210-v1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_trendnet_tew-810dr.dts treewide: add space before SPDX identifier 2020-11-28 19:03:27 +08:00
mt7620a_xiaomi_miwifi-mini.dts ramips: do not enable unused GPIO controllers 2020-12-18 11:39:28 +08:00
mt7620a_xiaomi_miwifi-r3.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_youku_yk1.dts Merge Mainline 2021-05-13 23:01:12 +08:00
mt7620a_yukai_bocco.dts ramips: do not enable unused GPIO controllers 2020-12-18 11:39:28 +08:00
mt7620a_zbtlink_zbt-ape522ii.dts ramips: do not enable unused GPIO controllers 2020-12-18 11:39:28 +08:00
mt7620a_zbtlink_zbt-we826-16m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_zbtlink_zbt-we826-32m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_zbtlink_zbt-we826-e.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_zbtlink_zbt-we826.dtsi ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
mt7620a_zbtlink_zbt-we1026-5g-16m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_zbtlink_zbt-we1026-5g.dtsi ramips: remove model name from LED labels 2020-11-21 19:29:29 +08:00
mt7620a_zbtlink_zbt-we1026-h-32m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a_zbtlink_zbt-we1026-h.dtsi ramips: remove model name from LED labels 2020-11-21 19:29:29 +08:00
mt7620a_zbtlink_zbt-we1026.dtsi ramips: add basic support for kernel 5.4 2020-04-16 10:00:29 +08:00
mt7620a_zte_q7.dts ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
mt7620a_zyxel_keenetic-viva.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620a.dtsi ramips: gpio-ralink: use ngpios, not ralink,num-gpios 2021-04-15 23:15:49 +08:00
mt7620n_asus_rt-n12p.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620n_asus_rt-n14u.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620n_buffalo_wmr-300.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620n_comfast_cf-wr800n.dts ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
mt7620n_dlink_dwr-116-a1.dts ramips: do not enable unused GPIO controllers 2020-12-18 11:39:28 +08:00
mt7620n_dlink_dwr-921-c1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620n_dlink_dwr-922-e2.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620n_elecom_wrh-300cr.dts ramips: do not enable unused GPIO controllers 2020-12-18 11:39:28 +08:00
mt7620n_hootoo_ht-tm05.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620n_kimax_u35wf.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620n_kingston_mlw221.dts ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
mt7620n_kingston_mlwg2.dts ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
mt7620n_netgear_jwnr2010-v5.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620n_netgear_n300.dtsi ramips: sync official source code 2020-09-12 15:01:12 +08:00
mt7620n_nexx_wt3020-4m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620n_nexx_wt3020-8m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620n_nexx_wt3020.dtsi ramips: do not enable unused GPIO controllers 2020-12-18 11:39:28 +08:00
mt7620n_ravpower_rp-wd03.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620n_sunvalley_filehub.dtsi kernel: mtdsplit_uimage: replace "openwrt, okli" parser 2021-01-23 12:17:18 +08:00
mt7620n_vonets_var11n-300.dts ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
mt7620n_wrtnode_wrtnode.dts ramips: do not enable unused GPIO controllers 2020-12-18 11:39:28 +08:00
mt7620n_zbtlink_zbt-cpe102.dts ramips: do not enable unused GPIO controllers 2020-12-18 11:39:28 +08:00
mt7620n_zbtlink_zbt-wa05.dts ramips: do not enable unused GPIO controllers 2020-12-18 11:39:28 +08:00
mt7620n_zbtlink_zbt-we2026.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620n_zbtlink_zbt-wr8305rt.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620n_zyxel_keenetic-omni-ii.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620n_zyxel_keenetic-omni.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7620n.dtsi ramips: gpio-ralink: use ngpios, not ralink,num-gpios 2021-04-15 23:15:49 +08:00
mt7621_adslr_g7.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_afoundry_ew1200.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_alfa-network_quad-e4g.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_ampedwireless_ally-00x19k.dts ramips: add support for Amped Wireless ALLY router and extender 2021-06-06 23:25:05 +08:00
mt7621_ampedwireless_ally-r1900k.dts ramips: add support for Amped Wireless ALLY router and extender 2021-06-06 23:25:05 +08:00
mt7621_ampedwireless_ally.dtsi ramips: add support for Amped Wireless ALLY router and extender 2021-06-06 23:25:05 +08:00
mt7621_asiarf_ap7621-001.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_asiarf_ap7621-nv1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_asiarf_ap7621.dtsi ramips: remove model name from LED labels 2020-11-21 19:29:29 +08:00
mt7621_asus_rt-ac57u.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_asus_rt-ac65p.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_asus_rt-ac85p.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_asus_rt-acx5p.dtsi ramips: remove model name from LED labels 2020-11-21 19:29:29 +08:00
mt7621_asus_rt-n56u-b1.dts ramips: add support for ASUS RT-N56U B1 2020-12-05 17:09:15 +08:00
mt7621_buffalo_wsr-600dhp.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_buffalo_wsr-1166dhp.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_buffalo_wsr-2533dhpl.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_cudy_wr1300.dts ramips: add support for Cudy WR1300 2021-02-10 12:05:09 +08:00
mt7621_cudy_wr2100.dts ramips: add support for Cudy WR2100 2021-05-27 23:24:56 +08:00
mt7621_d-team_newifi-d2.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_d-team_pbr-m1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_dlink_dir-8xx-a1.dtsi ramips: add support for D-Link DIR-882 R1 2020-12-25 19:20:22 +08:00
mt7621_dlink_dir-8xx-r1.dtsi ramips: add support for D-Link DIR-882 R1 2020-12-25 19:20:22 +08:00
mt7621_dlink_dir-8xx-x1.dtsi ramips: add support for D-Link DIR-882 R1 2020-12-25 19:20:22 +08:00
mt7621_dlink_dir-860l-b1.dts ramips: overwrite reset gpio properties in DIR-860L DTS 2021-02-24 12:24:45 +08:00
mt7621_dlink_dir-867-a1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_dlink_dir-878-a1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_dlink_dir-882-a1.dts ramips: add support for D-Link DIR-882 R1 2020-12-25 19:20:22 +08:00
mt7621_dlink_dir-882-r1.dts ramips: add support for D-Link DIR-882 R1 2020-12-25 19:20:22 +08:00
mt7621_dlink_dir-882-x1.dtsi ramips: add support for D-Link DIR-882 R1 2020-12-25 19:20:22 +08:00
mt7621_dlink_dir-1960-a1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_dlink_dir-2640-a1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_dlink_dir-2660-a1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_dlink_dir-xx60-a1.dtsi kernel: mtdsplit_uimage: replace "fonfxc" and "sge" parsers 2021-01-23 12:14:20 +08:00
mt7621_edimax_ra21s.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_edimax_re23s.dts kernel: mtdsplit_uimage: replace "edimax, uimage" parser 2021-01-23 12:19:11 +08:00
mt7621_edimax_rg21s.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_edimax_rx21s.dtsi ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_elecom_wrc-1167ghbk2-s.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_elecom_wrc-1167gs2-b.dts ramips: add support for ELECOM WRC-1167GS2-B 2020-12-25 19:22:31 +08:00
mt7621_elecom_wrc-1167gst2.dts ramips: add support for ELECOM WRC-1167GST2 2020-12-25 19:22:34 +08:00
mt7621_elecom_wrc-1750gs.dts ramips: mt7621: create DTSI for ELECOM WRC GS devices with 2 PCI 2020-12-25 19:22:26 +08:00
mt7621_elecom_wrc-1750gst2.dts ramips: add support for ELECOM WRC-1750GST2 2021-03-23 11:20:58 +08:00
mt7621_elecom_wrc-1750gsv.dts ramips: mt7621: create DTSI for ELECOM WRC GS devices with 2 PCI 2020-12-25 19:22:26 +08:00
mt7621_elecom_wrc-1900gst.dts ramips: mt7621: create DTSI for ELECOM WRC GS devices with 2 PCI 2020-12-25 19:22:26 +08:00
mt7621_elecom_wrc-2533gst2.dts ramips: mt7621: create DTSI for ELECOM WRC GS devices with 2 PCI 2020-12-25 19:22:26 +08:00
mt7621_elecom_wrc-2533gst.dts ramips: mt7621: create DTSI for ELECOM WRC GS devices with 2 PCI 2020-12-25 19:22:26 +08:00
mt7621_elecom_wrc-gs-1pci.dtsi ramips: add support for ELECOM WRC-1167GS2-B 2020-12-25 19:22:31 +08:00
mt7621_elecom_wrc-gs-2pci.dtsi ramips: mt7621: create DTSI for ELECOM WRC GS devices with 2 PCI 2020-12-25 19:22:26 +08:00
mt7621_elecom_wrc-gs.dtsi ramips: add support for ELECOM WRC-1167GS2-B 2020-12-25 19:22:31 +08:00
mt7621_firefly_firewrt.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_gehua_ghl-r-001.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_glinet_gl-mt1300.dts ramips: remove obsolete mx25l25635f compatible hack 2021-02-24 12:25:52 +08:00
mt7621_gnubee_gb-pc1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_gnubee_gb-pc2.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_hiwifi_hc5962.dts treewide: use more descriptive names for concatenated partitions 2020-12-28 11:20:45 +08:00
mt7621_iodata_wn-ax1167gr2.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_iodata_wn-ax1167gr.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_iodata_wn-ax2033gr.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_iodata_wn-dx1167r.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_iodata_wn-dx1200gr.dts ramips: add support for I-O DATA WN-DX1200GR 2021-02-08 12:06:16 +08:00
mt7621_iodata_wn-gx300gr.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_iodata_wn-xx-xr.dtsi ramips: remove model name from LED labels 2020-11-21 19:29:29 +08:00
mt7621_iodata_wnpr2600g.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_iptime_a6ns-m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_iptime_a8004t.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_jcg_jhr-ac876m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_jcg_q20.dts ramips: jcg q20: improve support with upstream review 2021-05-24 23:40:10 +08:00
mt7621_jcg_y2.dts ramips: add support for JCG Y2 2020-12-18 20:24:12 +08:00
mt7621_jdcloud_re-sp-01b.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_lenovo_newifi-d1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_linksys_e5600.dts ramips: add support for Linksys E5600 2021-06-06 23:20:49 +08:00
mt7621_linksys_ea7xxx.dtsi ramips: remove model name from LED labels 2020-11-21 19:29:29 +08:00
mt7621_linksys_ea7300-v1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_linksys_ea7500-v2.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_linksys_re6500.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_mediatek_ap-mt7621a-v60.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_mediatek_mt7621-eval-board.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_mikrotik_routerboard-7xx.dtsi ramips: sync official source code 2020-09-12 15:01:12 +08:00
mt7621_mikrotik_routerboard-750gr3.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_mikrotik_routerboard-760igs.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_mikrotik_routerboard-m11g.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_mikrotik_routerboard-m33g.dts ramips: enable additional UART on MikroTik RouterBOARD M33G 2021-06-06 23:17:31 +08:00
mt7621_mikrotik.dtsi ramips: sync official source code 2020-09-12 15:01:12 +08:00
mt7621_motorola_mr2600.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_mqmaker_witi.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_mtc_wr1201.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_netgear_ex6150.dts ramips: overwrite reset gpio properties in EX6150 DTS 2021-02-20 12:27:20 +08:00
mt7621_netgear_r6220.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_netgear_r6260.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_netgear_r6350.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_netgear_r6700-v2.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_netgear_r6800.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_netgear_r6850.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_netgear_sercomm_ayx.dtsi ramips: remove model name from LED labels 2020-11-21 19:29:29 +08:00
mt7621_netgear_sercomm_bzv.dtsi ramips: use mt proprietary driver for Netgear R6800 2021-02-13 16:27:43 +08:00
mt7621_netgear_sercomm_chj.dtsi ramips: remove model name from LED labels 2020-11-21 19:29:29 +08:00
mt7621_netgear_wac104.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_netgear_wac124.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_netgear_wndr3700-v5.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_netis_wf2881.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_phicomm_k2p.dts ramips: increase SPI frequency for Phicomm series devices 2021-03-23 11:16:28 +08:00
mt7621_planex_vr500.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_samknows_whitebox-v8.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_storylink_sap-g3200u3.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_telco-electronics_x1.dts ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
mt7621_thunder_timecloud.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_totolink_a7000r.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_tplink_archer-a6-v3.dts ramips: add support for TP-Link Archer A6 v3 2021-05-27 23:19:34 +08:00
mt7621_tplink_archer-c6u-v1.dts ramips: add support for TP-Link Archer C6U v1 (EU) 2021-05-27 23:23:17 +08:00
mt7621_tplink_eap235-wall-v1.dts ramips: mt7621: add TP-Link EAP235-Wall support 2021-02-20 12:18:08 +08:00
mt7621_tplink_re350-v1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_tplink_re500-v1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_tplink_re650-v1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_tplink_rexx0-v1.dtsi ramips: remove model name from LED labels 2020-11-21 19:29:29 +08:00
mt7621_ubnt_edgerouter-x-sfp.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_ubnt_edgerouter-x.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_ubnt_edgerouter-x.dtsi ramips: sync official source code 2020-09-12 15:01:12 +08:00
mt7621_ubnt_unifi-nanohd.dts ramips: remove obsolete mx25l25635f compatible hack 2021-02-19 23:57:16 +08:00
mt7621_unielec_u7621-01-16m.dts ramips: add support for UniElec U7621-01 2021-02-06 12:11:36 +08:00
mt7621_unielec_u7621-01.dtsi ramips: add support for UniElec U7621-01 2021-02-06 12:11:36 +08:00
mt7621_unielec_u7621-06-16m.dts ramips: replace full-text licenses by SPDX identifier 2021-02-06 12:12:04 +08:00
mt7621_unielec_u7621-06-64m.dts ramips: replace full-text licenses by SPDX identifier 2021-02-06 12:12:04 +08:00
mt7621_unielec_u7621-06.dtsi ramips: replace full-text licenses by SPDX identifier 2021-02-06 12:12:04 +08:00
mt7621_wavlink_wl-wn531a6.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_wevo_11acnas.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_wevo_w2914ns-v2.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_wevo_w2914ns-v2.dtsi ramips: sync official source code 2020-09-12 15:01:12 +08:00
mt7621_winstars_ws-wn583a6.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_xiaomi_mi-router-ac2100.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_xiaomi_mir3g-v2.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_xiaomi_mir3g.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_xiaomi_mir3p.dts ramips: fix LEDs status for XiaoMi R3P 2021-01-09 21:10:45 +08:00
mt7621_xiaomi_mir4.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_xiaomi_redmi-router-ac2100.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_xiaomi_router-ac2100.dtsi target/ramips: sync with recently changes from Lean 2020-07-19 20:16:32 +08:00
mt7621_xiaoyu_xy-c5.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_xzwifi_creativebox-v1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_youhua_wr1200js.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_youku_yk-l2.dts ramips: remove redundant status for USB controllers 2020-12-08 11:38:11 +08:00
mt7621_zbtlink_zbt-we1326.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_zbtlink_zbt-we3526.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_zbtlink_zbt-wg108.dts ramips: add support for zbt-wg108 2020-12-19 18:00:54 +08:00
mt7621_zbtlink_zbt-wg2626.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_zbtlink_zbt-wg3526-16m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_zbtlink_zbt-wg3526-32m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_zbtlink_zbt-wg3526.dtsi ramips: remove model name from LED labels 2020-11-21 19:29:29 +08:00
mt7621_zio_freezio.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621_zyxel_nr7101.dts ramips: use standard naming scheme for Zyxel NR7101 LED nodes 2021-05-11 01:03:08 +08:00
mt7621_zyxel_wap6805.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7621.dtsi ramips: move aliases to the top in SoC DTSI files 2021-02-23 12:18:25 +08:00
mt7628an_alfa-network_awusfree1.dts ramips: replace full-text licenses by SPDX identifier 2021-02-06 12:12:04 +08:00
mt7628an_asus_rt-n1x.dtsi ramips: remove model name from LED labels 2020-11-21 19:29:29 +08:00
mt7628an_asus_rt-n10p-v3.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_asus_rt-n11p-b1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_asus_rt-n12-vp-b1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_buffalo_wcr-1166ds.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_cudy_wr1000.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_d-team_pbr-d1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_duzun_dm06.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_elecom_wrc-1167fs.dts ramips: add support for ELECOM WRC-1167FS 2021-02-12 12:11:22 +08:00
mt7628an_glinet_gl-mt300n-v2.dts ramips: remove redundant status for USB controllers 2020-12-08 11:38:11 +08:00
mt7628an_glinet_microuter-n300.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_glinet_vixmini_microuter.dtsi ramips: remove model name from LED labels 2020-11-21 19:29:29 +08:00
mt7628an_glinet_vixmini.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_hak5_wifi-pineapple-mk7.dts ramips: add support for the Hak5 WiFi Pineapple Mark 7 2020-11-21 18:00:13 +08:00
mt7628an_hilink_hlk-7628n.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_hilink_hlk-7688a.dts ramips: add support for Hi-Link HLK-7688A 2021-05-28 15:29:28 +08:00
mt7628an_hiwifi_hc5x61a.dtsi ramips: add basic support for kernel 5.4 2020-04-16 10:00:29 +08:00
mt7628an_hiwifi_hc5661a.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_hiwifi_hc5761a.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_hiwifi_hc5861b.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_iptime_a3.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_iptime_a604m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_iptime.dtsi ramips: add basic support for kernel 5.4 2020-04-16 10:00:29 +08:00
mt7628an_jotale_js76x8-8m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_jotale_js76x8-16m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_jotale_js76x8-32m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_jotale_js76x8.dtsi ramips: remove model name from LED labels 2020-11-21 19:29:29 +08:00
mt7628an_mediatek_linkit-smart-7688.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_mediatek_mt7628an-eval-board.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_mercury_mac1200r-v2.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_netgear_r6xxx.dtsi ramips: remove model name from LED labels 2020-11-21 19:29:29 +08:00
mt7628an_netgear_r6020.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_netgear_r6080.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_netgear_r6120.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_onion_omega2.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_onion_omega2.dtsi ramips: remove model name from LED labels 2020-11-21 19:29:29 +08:00
mt7628an_onion_omega2p.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_rakwireless_rak633.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_ravpower_rp-wd009.dts ramips: remove redundant status for USB controllers 2020-12-08 11:38:11 +08:00
mt7628an_skylab_skw92a.dts ramips: remove redundant status for USB controllers 2020-12-08 11:38:11 +08:00
mt7628an_tama_w06.dts ramips: remove redundant status for USB controllers 2020-12-08 11:38:11 +08:00
mt7628an_totolink_a3.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_totolink_lr1200.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_tplink_8m-split-uboot.dtsi ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-08 11:37:42 +08:00
mt7628an_tplink_8m.dtsi ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-08 11:37:42 +08:00
mt7628an_tplink_archer-c20-v4.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-08 11:37:42 +08:00
mt7628an_tplink_archer-c20-v5.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-08 11:37:42 +08:00
mt7628an_tplink_archer-c50-v3.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-08 11:37:42 +08:00
mt7628an_tplink_archer-c50-v4.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-08 11:37:42 +08:00
mt7628an_tplink_re200-v2.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_tplink_re200-v3.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_tplink_re200-v4.dts ramips: add support for TP-Link RE200 v4 2020-10-20 11:30:49 +08:00
mt7628an_tplink_re200.dtsi ramips: remove model name from LED labels 2020-11-21 19:29:29 +08:00
mt7628an_tplink_re220-v2.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_tplink_re305-v1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_tplink_tl-mr3020-v3.dts ramips: remove redundant status for USB controllers 2020-12-08 11:38:11 +08:00
mt7628an_tplink_tl-mr3420-v5.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-08 11:37:42 +08:00
mt7628an_tplink_tl-mr6400-v4.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-08 11:37:42 +08:00
mt7628an_tplink_tl-wa801nd-v5.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-08 11:37:42 +08:00
mt7628an_tplink_tl-wr802n-v4.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-08 11:37:42 +08:00
mt7628an_tplink_tl-wr840n-v4.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-08 11:37:42 +08:00
mt7628an_tplink_tl-wr840n-v5.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_tplink_tl-wr841n-v13.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-08 11:37:42 +08:00
mt7628an_tplink_tl-wr841n-v14.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_tplink_tl-wr842n-v5.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-08 11:37:42 +08:00
mt7628an_tplink_tl-wr850n-v2.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-08 11:37:42 +08:00
mt7628an_tplink_tl-wr902ac-v3.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-08 11:37:42 +08:00
mt7628an_unielec_u7628-01-16m.dts ramips: replace full-text licenses by SPDX identifier 2021-02-06 12:12:04 +08:00
mt7628an_unielec_u7628-01.dtsi ramips: replace full-text licenses by SPDX identifier 2021-02-06 12:12:04 +08:00
mt7628an_vocore_vocore2-lite.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_vocore_vocore2.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_vocore_vocore2.dtsi ramips: add basic support for kernel 5.4 2020-04-16 10:00:29 +08:00
mt7628an_wavlink_wl-wn570ha1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_wavlink_wl-wn575a3.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_wavlink_wl-wn577a2.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_wavlink_wl-wn578a2.dts ramips: add support for Wavlink WL-WN578A2 2021-05-28 15:29:39 +08:00
mt7628an_widora_neo-16m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_widora_neo-32m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_widora_neo.dtsi ramips: remove model name from LED labels 2020-11-21 19:29:29 +08:00
mt7628an_wiznet_wizfi630s.dts treewide: add space before SPDX identifier 2020-11-28 19:03:27 +08:00
mt7628an_wrtnode_wrtnode2.dtsi ramips: dts: use generic node name for flash 2020-05-10 11:01:51 +08:00
mt7628an_wrtnode_wrtnode2p.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_wrtnode_wrtnode2r.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_xiaomi_mi-router-4c.dts treewide: add space before SPDX identifier 2020-11-28 19:03:27 +08:00
mt7628an_xiaomi_mir4a-100m.dts treewide: add space before SPDX identifier 2020-11-28 19:03:27 +08:00
mt7628an_xiaomi_miwifi-nano.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_zbtlink_zbt-we1226.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
mt7628an_zyxel_keenetic-extra-ii.dts ramips: remove redundant status for USB controllers 2020-12-08 11:38:11 +08:00
mt7628an.dtsi ramips: move aliases to the top in SoC DTSI files 2021-02-23 12:18:25 +08:00
rt2880_airlink101_ar670w.dts ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
rt2880_airlink101_ar725w.dts ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
rt2880_asus_rt-n15.dts ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
rt2880_belkin_f5d8235-v1.dts ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
rt2880_buffalo_wli-tx4-ag300n.dts ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
rt2880_buffalo_wzr-agl300nh.dts ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
rt2880_dlink_dap-1522-a1.dts ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
rt2880_ralink_v11st-fe.dts ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
rt2880.dtsi ramips: gpio-ralink: use ngpios, not ralink,num-gpios 2021-04-15 23:15:49 +08:00
rt3050_8devices_carambola.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3050_allnet_all0256n-4m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3050_allnet_all0256n-8m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3050_allnet_all0256n.dtsi ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
rt3050_alphanetworks_asl26555-8m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3050_alphanetworks_asl26555-16m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3050_alphanetworks_asl26555.dtsi ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
rt3050_arcwireless_freestation5.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3050_asus_rt-g32-b1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3050_asus_rt-n10-plus.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3050_asus_wl-330n3g.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3050_asus_wl-330n.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3050_dlink_dcs-930.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3050_dlink_dir-300-b1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3050_dlink_dir-600-b1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3050_dlink_dir-615-d.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3050_dlink_dir-620-a1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3050_edimax_3g-6200n.dts kernel: mtdsplit_uimage: replace "edimax, uimage" parser 2021-01-23 12:19:11 +08:00
rt3050_edimax_3g-6200nl.dts kernel: mtdsplit_uimage: replace "edimax, uimage" parser 2021-01-23 12:19:11 +08:00
rt3050_huawei_d105.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3050_jcg_jhr-n805r.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3050_netcore_nw718.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3050_sparklan_wcr-150gn.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3050_teltonika_rut5xx.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3050_tenda_w150m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3050_trendnet_tew-638apb-v2.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3050.dtsi ramips: gpio-ralink: use ngpios, not ralink,num-gpios 2021-04-15 23:15:49 +08:00
rt3052_accton_wr6202.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_alfa-network_w502u.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_argus_atp-52b.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_asiarf_awapn2403.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_asus_rt-n13u.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_aximcom_mr-102n.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_aztech_hw550-3g.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_belkin_f5d8235-v2.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_buffalo_whr-g300n.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_dlink_dap-1350.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_engenius_esr-9753.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_fon_fonera-20n.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_hauppauge_broadway.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_huawei_hg255d.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_jcg_jhr-n825r.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_jcg_jhr-n926r.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_mofinetwork_mofi3500-3gn.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_netgear_wnce2001.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_nexaira_bc2.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_omnima_miniembwifi.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_petatel_psr-680w.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_planex_mzk-w300nh2.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_planex_mzk-wdpr.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_poray_ip2202.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_prolink_pwh2004.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_ralink_v22rw-2x2.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_sitecom_wl-351.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_skyline_sl-r7205.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_tenda_3g300m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_tenda_w306r-v2.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_unbranded_wr512-3gn-4m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_unbranded_wr512-3gn-8m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_unbranded_wr512-3gn.dtsi ramips: remove model name from LED labels 2020-11-21 19:29:29 +08:00
rt3052_unbranded_xdx-rn502j.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_upvel_ur-326n4g.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_upvel_ur-336un.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_zyxel_keenetic.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3052_zyxel_nbg-419n.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3352_allnet_all5002.dts ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
rt3352_dlink_dir-615-h1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3352_dlink_dir-620-d1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3352_zte_mf283plus.dts ramips: add support for ZTE MF283+ 2021-02-27 12:06:37 +08:00
rt3352_zyxel_nbg-419n-v2.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3352.dtsi ramips: gpio-ralink: use ngpios, not ralink,num-gpios 2021-04-15 23:15:49 +08:00
rt3662_asus_rt-n56u.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3662_dlink_dir-645.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3662_edimax_br-6475nd.dts kernel: mtdsplit_uimage: replace "edimax, uimage" parser 2021-01-23 12:19:11 +08:00
rt3662_loewe_wmdr-143n.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3662_omnima_hpm.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3662_samsung_cy-swr1100.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3883_belkin_f9k110x.dtsi ramips: do not enable unused GPIO controllers 2020-12-18 11:39:28 +08:00
rt3883_belkin_f9k1109v1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3883_sitecom_wlr-6000.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3883_trendnet_tew-691gr.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3883_trendnet_tew-692gr.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt3883.dtsi ramips: gpio-ralink: use ngpios, not ralink,num-gpios 2021-04-15 23:15:49 +08:00
rt5350_7links_px-4885-4m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt5350_7links_px-4885-8m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt5350_7links_px-4885.dtsi ramips: remove model name from LED labels 2020-11-21 19:29:29 +08:00
rt5350_airlive_air3gii.dts ramips: drop redundant status for gpio/gpio0 2020-12-05 17:19:39 +08:00
rt5350_allnet_all5003.dts ramips: remove redundant status for USB controllers 2020-12-08 11:38:11 +08:00
rt5350_asiarf_awm002-evb-4m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt5350_asiarf_awm002-evb-8m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt5350_asiarf_awm002-evb.dtsi ramips: remove redundant status for USB controllers 2020-12-08 11:38:11 +08:00
rt5350_belkin_f7c027.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt5350_dlink_dcs-930l-b1.dts ramips: remove redundant status for USB controllers 2020-12-08 11:38:11 +08:00
rt5350_dlink_dir-300-b7.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt5350_dlink_dir-320-b1.dts ramips: remove redundant status for USB controllers 2020-12-08 11:38:11 +08:00
rt5350_dlink_dir-610-a1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt5350_dlink_dwr-512-b.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt5350_easyacc_wizard-8800.dts ramips: do not enable unused GPIO controllers 2020-12-18 11:39:28 +08:00
rt5350_hame_mpr-a1.dts ramips: do not enable unused GPIO controllers 2020-12-18 11:39:28 +08:00
rt5350_hame_mpr-a2.dts ramips: remove redundant status for USB controllers 2020-12-08 11:38:11 +08:00
rt5350_hilink_hlk-rm04.dts ramips: remove redundant status for USB controllers 2020-12-08 11:38:11 +08:00
rt5350_hootoo_ht-tm02.dts ramips: remove redundant status for USB controllers 2020-12-08 11:38:11 +08:00
rt5350_intenso_memory2move.dts ramips: remove redundant status for USB controllers 2020-12-08 11:38:11 +08:00
rt5350_nexx_wt1520-4m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt5350_nexx_wt1520-8m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt5350_nexx_wt1520.dtsi ramips: remove redundant status for USB controllers 2020-12-08 11:38:11 +08:00
rt5350_nixcore_x1-8m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt5350_nixcore_x1-16m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt5350_nixcore_x1.dtsi ramips: remove redundant status for USB controllers 2020-12-08 11:38:11 +08:00
rt5350_olimex_rt5350f-olinuxino-evb.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt5350_olimex_rt5350f-olinuxino.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt5350_olimex_rt5350f-olinuxino.dtsi ramips: drop redundant definitions of serial0 in aliases 2021-02-23 12:15:12 +08:00
rt5350_omnima_miniembplug.dts ramips: remove redundant status for USB controllers 2020-12-08 11:38:11 +08:00
rt5350_planex_mzk-dp150n.dts ramips: do not enable unused GPIO controllers 2020-12-18 11:39:28 +08:00
rt5350_poray_m3.dts ramips: remove redundant status for USB controllers 2020-12-08 11:38:11 +08:00
rt5350_poray_m4-4m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt5350_poray_m4-8m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt5350_poray_m4.dtsi ramips: remove redundant status for USB controllers 2020-12-08 11:38:11 +08:00
rt5350_poray_x5.dts ramips: remove redundant status for USB controllers 2020-12-08 11:38:11 +08:00
rt5350_poray_x8.dts ramips: remove redundant status for USB controllers 2020-12-08 11:38:11 +08:00
rt5350_tenda_3g150b.dts ramips: do not enable unused GPIO controllers 2020-12-18 11:39:28 +08:00
rt5350_trendnet_tew-714tru.dts ramips: remove redundant status for USB controllers 2020-12-08 11:38:11 +08:00
rt5350_unbranded_a5-v11.dts ramips: do not enable unused GPIO controllers 2020-12-18 11:39:28 +08:00
rt5350_vocore_vocore-8m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt5350_vocore_vocore-16m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt5350_vocore_vocore.dtsi ramips: remove redundant status for USB controllers 2020-12-08 11:38:11 +08:00
rt5350_wansview_ncs601w.dts ramips: remove redundant status for USB controllers 2020-12-08 11:38:11 +08:00
rt5350_wiznet_wizfi630a.dts ramips: do not enable unused GPIO controllers 2020-12-18 11:39:28 +08:00
rt5350_zorlik_zl5900v2.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt5350_zyxel_keenetic-lite-b.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt5350_zyxel_keenetic-start.dts ramips: move dts-v1 statement to top-level DTSI files 2020-11-28 19:03:05 +08:00
rt5350.dtsi ramips: gpio-ralink: use ngpios, not ralink,num-gpios 2021-04-15 23:15:49 +08:00