An opensource OpenWrt variant for mainland China users.
687ad2a014
About the device
----------------
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M
FLASH: 8MB
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
GbE: 2x (RTL8211F)
BTN: - WPS
- Reset
- Router/Repeater/AP (3-way slide-switch)
LED: - WPS (blue)
- 3-segment Wifi signal representation (blue)
- WiFi (blue)
- WAN (blue)
- LAN (blue)
- Power (blue)
UART: UART is present as Pads with through-holes on the PCB. They are
located next to the reset button and are labelled Vcc/TX/RX/GND as
appropriate. Use 3.3V, 57600-8N1.
Installation
------------
Using the webcmd interface
--------------------------
Warning: Do not update to the latest Wavlink firmware (version
20201201) as this removes the webcmd console and you will need to
use the serial port instead.
You will need to have built uboot/sqauashfs image for this device,
and you will need to provide an HTTP service where the image can
be downloaded from that is accessible by the device.
You cannot use the device manufacturers firmware upgrade interface
as it rejects the OpenWrt image.
1. Log into the device's admin portal. This is necessary to
authenticate you as a user in order to be able to access the
webcmd interface.
2. Navigate to http://<device-ip>/webcmd.shtml - you can access
the console directly through this page, or you may wish to
launch the installed `telnetd` and use telnet instead.
* Using telnet is recommended since it provides a more
convenient shell interface that the web form.
* Launch telnetd from the form with the command `telnetd`.
* Check the port that telnetd is running on using
`netstat -antp|grep telnetd`, it is likely to be 2323.
* Connect to the target using `telnet`. The username should
be `admin2860`, and the password is your admin password.
3. On the target use `curl` to download the image.
e.g. `curl -L -O http://<some-other-lan-ip>/openwrt-ramips-mt7620-\
wavlink_wl-wn579x3-squashfs-sysupgrade.bin`.
Check the hash using `md5sum`.
4. Use the mtd_write command to flash the image.
* The flash partition should be mtd4, but check
/sys/class/mtd/mtd4/name first. The partition should be
called 'Kernel'.
* To flash use the following command:
`mtd_write -r -e /dev/mtd<n> write <image-file> /dev/mtd<n>`
Where mtd<n> is the Kernel partition, and <image-file> is
the OpenWrt image previously downloaded.
* The command above will erase, flash and then reboot the
device. Once it reboots it will be running OpenWrt.
Connect via ssh to the device at 192.168.1.1 on the LAN port.
The WAN port will be configured via DHCP.
Using the serial port
---------------------
The device uses uboot like many other MT7260a based boards. To
use this interface, you will need to connect to the serial
interface, and provide a TFTP server. At boot follow the
bootloader menu and select option 2 to erase/flash the image.
Provide the address and filename details for the tftp server.
The bootloader will do the rest.
Once the image is flashed, the board will boot into OpenWrt. The
console is available over the serial port.
Signed-off-by: Ben Gainey <ba.gainey@googlemail.com>
|
||
|---|---|---|
| config | ||
| include | ||
| LICENSES | ||
| package | ||
| scripts | ||
| target | ||
| toolchain | ||
| tools | ||
| .gitattributes | ||
| .gitignore | ||
| BSDmakefile | ||
| Config.in | ||
| CONTRIBUTED.md | ||
| COPYING | ||
| feeds.conf.default | ||
| Makefile | ||
| README.md | ||
| rules.mk | ||
PROJECT IMMORTALWRT
The Core Source Code of ImmortalWrt
Welcome to our Telegram Group: @ctcgfw_openwrt_discuss.
How to make it
Minimum requirements
Linux with case sensitive
2G DDR2 RAM
2 CPU Cores (AMD64, 1.4Ghz)
25G disk space left
Has access to both ChinaNet & Internet
Install the necessary packages (for Ubuntu user)
sudo apt-get update -y
sudo apt-get full-upgrade -y
sudo apt-get install -y build-essential asciidoc binutils bzip2 gawk gettext git libncurses5-dev libz-dev patch unzip zlib1g-dev lib32gcc1 libc6-dev-i386 subversion flex uglifyjs git-core gcc-multilib g++-multilib p7zip p7zip-full msmtp libssl-dev texinfo libreadline-dev libglib2.0-dev xmlto qemu-utils upx libelf-dev autoconf automake libtool autopoint ccache curl wget vim nano python python3 python-pip python3-pip python-ply python3-ply haveged lrzsz device-tree-compiler scons antlr3 gperf intltool rsync
For mainland China & Ubuntu(16.04+) user, you may run the following command to setup quickly:
sudo bash -c "bash <(curl -s https://build-scripts.project-openwrt.eu.org/init_build_environment.sh)"
Clone the source
git clone -b openwrt-18.06-k5.4 --single-branch https://github.com/immortalwrt/immortalwrt && cd immortalwrt
./scripts/feeds update -a && ./scripts/feeds install -a
Configure your firmware
make menuconfig
Make it
make -j$(nproc) V=s
Tips
You'd better not use root to make it, or you may be not able to use.
Default login address: 192.168.1.1, username is root and password is password.