An opensource OpenWrt variant for mainland China users.
6a16156857
AirTight Networks (later renamed to Mojo Networks) C-75 is a dual-band
access point, also sold by WatchGuard under name AP320.
Specification
SoC: Qualcomm Atheros QCA9550
RAM: 128 MiB DDR2
Flash: 2x 16 MiB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
5 GHz 3T3R QCA9890 oversized Mini PCIe card
Ethernet: 2x 10/100/1000 Mbps QCA8334
port labeled LAN1 is PoE capable (802.3at)
USB: 1x 2.0
LEDs: 7x which two are GPIO controlled, four switch controlled, one
controlled by wireless driver
Buttons: 1x GPIO controlled
Serial: RJ-45 port, Cisco pinout
baud: 115200, parity: none, flow control: none
JTAG: Yes, pins marked J1 on PCB
Installation
1. Prepare TFTP server with OpenWrt initramfs-kernel image.
2. Connect to one of LAN ports.
3. Connect to serial port.
4. Power on the device and when prompted to stop autoboot, hit any key.
5. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use
'setenv' to do that, then run following commands:
tftpboot 0x81000000 <openwrt_initramfs-kernel_image_name>
bootm 0x81000000
6. Wait about 1 minute for OpenWrt to boot.
7. Transfer OpenWrt sysupgrade image to /tmp directory and flash it
with:
sysupgrade -n /tmp/<openwrt_sysupgrade_image_name>
8. After flashing, the access point will reboot to OpenWrt. Wait few
minutes, until the Power LED stops blinking, then it's ready for
configuration.
Known issues
Green power LED does not work.
Additional information
The U-Boot fails to initialise ethernet ports correctly when a UART
adapter is attached to UART pins (marked J3 on PCB).
Cc: Vladimir Georgievsky <vladimir.georgievsky@yahoo.com>
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
|
||
|---|---|---|
| config | ||
| include | ||
| package | ||
| scripts | ||
| target | ||
| toolchain | ||
| tools | ||
| .gitattributes | ||
| .gitignore | ||
| BSDmakefile | ||
| Config.in | ||
| CONTRIBUTED.md | ||
| feeds.conf.default | ||
| LICENSE | ||
| Makefile | ||
| README.md | ||
| rules.mk | ||
PROJECT OPENWRT
The Source Code of OpenWrt-Lean Modified by CTCGFW
Welcome to our Telegram Group: @ctcgfw_openwrt_discuss.
How to make it
Minimum requirements
Linux with case sensitive
2G DDR2 RAM
2 CPU Cores (AMD64, 1.4Ghz)
25G disk space left
Has access to both ChinaNet & Internet
Install the necessary packages (for Ubuntu user)
sudo apt-get update -y
sudo apt-get full-upgrade -y
sudo apt-get install -y build-essential asciidoc binutils bzip2 gawk gettext git libncurses5-dev libz-dev patch unzip zlib1g-dev lib32gcc1 libc6-dev-i386 subversion flex uglifyjs git-core gcc-multilib g++-multilib p7zip p7zip-full msmtp libssl-dev texinfo libreadline-dev libglib2.0-dev xmlto qemu-utils upx libelf-dev autoconf automake libtool autopoint ccache curl wget vim nano python python3 python-pip python3-pip python-ply python3-ply haveged lrzsz device-tree-compiler scons antlr3 gperf intltool rsync
For mainland China & Ubuntu(16.04+) user, you may run the following command to setup quickly:
sudo bash -c "bash <(curl -s https://build-scripts.project-openwrt.eu.org/init_build_environment.sh)"
Clone the source
git clone -b openwrt-18.06-k5.4 --single-branch https://github.com/project-openwrt/openwrt && cd openwrt
./scripts/feeds update -a && ./scripts/feeds install -a
Configure your firmware
make menuconfig
Make it
make -j1 V=s
Tips
You'd better not use root to make it, or you may be not able to use.
Default login address: 192.168.1.1, username is root and password is password.