fish/immortalwrt
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
7dbac3433f
immortalwrt/target/linux/ath79/dts
History
Michael Pratt 6de9287abd ath79: add support for Senao Engenius EAP1750H 
FCC ID: A8J-EAP1750H

Engenius EAP1750H is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+

**Specification:**

  - QCA9558 SOC
  - QCA9880 WLAN	PCI card, 5 GHz, 3x3, 26dBm
  - AR8035-A PHY	RGMII GbE with PoE+ IN
  - 40 MHz clock
  - 16 MB FLASH		MX25L12845EMI-10G
  - 2x 64 MB RAM	NT5TU32M16FG
  - UART at J10		populated
  - 4 internal antenna plates (5 dbi, omni-directional)
  - 5 LEDs, 1 button (power, eth0, 2G, 5G, WPS) (reset)

**MAC addresses:**

  MAC addresses are labeled as ETH, 2.4G, and 5GHz
  Only one Vendor MAC address in flash

  eth0 ETH  *:fb art 0x0
  phy1 2.4G *:fc ---
  phy0 5GHz *:fd ---

**Serial Access:**

  the RX line on the board for UART is shorted to ground by resistor R176
  therefore it must be removed to use the console
  but it is not necessary to remove to view boot log

  optionally, R175 can be replaced with a solder bridge short

  the resistors R175 and R176 are next to the UART RX pin at J10

**Installation:**

  2 ways to flash factory.bin from OEM:

  Method 1: Firmware upgrade page:

    OEM webpage at 192.168.1.1
    username and password "admin"
    Navigate to "Firmware Upgrade" page from left pane
    Click Browse and select the factory.bin image
    Upload and verify checksum
    Click Continue to confirm and wait 3 minutes

  Method 2: Serial to load Failsafe webpage:

    After connecting to serial console and rebooting...
    Interrupt uboot with any key pressed rapidly
    execute `run failsafe_boot` OR `bootm 0x9fd70000`
    wait a minute
    connect to ethernet and navigate to
    "192.168.1.1/index.htm"
    Select the factory.bin image and upload
    wait about 3 minutes

**Return to OEM:**

  If you have a serial cable, see Serial Failsafe instructions
  otherwise, uboot-env can be used to make uboot load the failsafe image

  ssh into openwrt and run
  `fw_setenv rootfs_checksum 0`
  reboot, wait 3 minutes
  connect to ethernet and navigate to 192.168.1.1/index.htm
  select OEM firmware image from Engenius and click upgrade

**TFTP recovery:**

  Requires serial console, reset button does nothing

  rename initramfs to 'vmlinux-art-ramdisk'
  make available on TFTP server at 192.168.1.101
  power board, interrupt boot
  execute tftpboot and bootm 0x81000000

  NOTE: TFTP is not reliable due to bugged bootloader
  set MTU to 600 and try many times
  if your TFTP server supports setting block size
  higher block size is better.

**Format of OEM firmware image:**

  The OEM software of EAP1750H is a heavily modified version
  of Openwrt Kamikaze. One of the many modifications
  is to the sysupgrade program. Image verification is performed
  simply by the successful ungzip and untar of the supplied file
  and name check and header verification of the resulting contents.
  To form a factory.bin that is accepted by OEM Openwrt build,
  the kernel and rootfs must have specific names...

    openwrt-ar71xx-generic-eap1750h-uImage-lzma.bin
    openwrt-ar71xx-generic-eap1750h-root.squashfs

  and begin with the respective headers (uImage, squashfs).
  Then the files must be tarballed and gzipped.
  The resulting binary is actually a tar.gz file in disguise.
  This can be verified by using binwalk on the OEM firmware images,
  ungzipping then untaring.

  Newer EnGenius software requires more checks but their script
  includes a way to skip them, otherwise the tar must include
  a text file with the version and md5sums in a deprecated format.

  The OEM upgrade script is at /etc/fwupgrade.sh.

  OKLI kernel loader is required because the OEM software
  expects the kernel to be no greater than 1536k
  and the factory.bin upgrade procedure would otherwise
  overwrite part of the kernel when writing rootfs.

Note on PLL-data cells:

  The default PLL register values will not work
  because of the external AR8035 switch between
  the SOC and the ethernet port.

  For QCA955x series, the PLL registers for eth0 and eth1
  can be see in the DTSI as 0x28 and 0x48 respectively.
  Therefore the PLL registers can be read from uboot
  for each link speed after attempting tftpboot
  or another network action using that link speed
  with `md 0x18050028 1` and `md 0x18050048 1`.

  The clock delay required for RGMII can be applied
  at the PHY side, using the at803x driver `phy-mode`.
  Therefore the PLL registers for GMAC0
  do not need the bits for delay on the MAC side.
  This is possible due to fixes in at803x driver
  since Linux 5.1 and 5.3

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2022-11-27 13:18:29 +01:00
..
ar724x_senao_loader-4k.dtsi ath79: add Senao 'failsafe' sysupgrade procedure 2021-04-08 09:20:59 +02:00
ar724x_senao_loader-64k.dtsi ath79: add Senao 'failsafe' sysupgrade procedure 2021-04-08 09:20:59 +02:00
ar724x_ubnt_xm_outdoor.dtsi ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar724x_ubnt_xm.dtsi ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar724x.dtsi ath79: move reference clock node to SoC dtsi 2022-11-09 22:55:33 +01:00
ar934x_ruckus_zf73xx.dtsi ath79: support Ruckus ZoneFlex 7372 2022-09-11 01:36:25 +02:00
ar934x_senao_loader.dtsi ath79: add Senao 'failsafe' sysupgrade procedure 2021-04-08 09:20:59 +02:00
ar934x.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar1022_iodata_wn-ag300dgr.dts ath79: enable UART in SoC DTSI files 2021-02-24 02:53:53 +01:00
ar1022_sitecom_wlr-7100.dts ath79: enable UART in SoC DTSI files 2021-02-24 02:53:53 +01:00
ar7100_mikrotik_routerboard-4xx.dtsi ath79: cleanup mikrotik routerboot partitions 2022-04-15 07:11:18 +02:00
ar7100.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar7161_adtran_bsap1800-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7161_adtran_bsap1840.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7161_adtran_bsap1880.dtsi ath79: bsap18x0: specify FIS directory location in dts 2022-06-24 17:10:24 +02:00
ar7161_aruba_ap-105.dts ath79: move reference clock node to SoC dtsi 2022-11-09 22:55:33 +01:00
ar7161_buffalo_wzr-600dhp.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7161_buffalo_wzr-hp-ag300h.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7161_buffalo_wzr-hp-ag300h.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar7161_dlink_dir-825-b1.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar7161_jjplus_ja76pf2.dts ath79: move reference clock node to SoC dtsi 2022-11-09 22:55:33 +01:00
ar7161_meraki_mr16.dts ath79: move reference clock node to SoC dtsi 2022-11-09 22:55:33 +01:00
ar7161_mikrotik_routerboard-493g.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7161_netgear_wndap360.dts ath79: move reference clock node to SoC dtsi 2022-11-09 22:55:33 +01:00
ar7161_netgear_wndr3700-v2.dts ath79: WNDR3700/3800/MAC: utilize nvmem for caldata fetching 2021-11-06 22:18:45 +01:00
ar7161_netgear_wndr3700.dts ath79: WNDR3700/3800/MAC: utilize nvmem for caldata fetching 2021-11-06 22:18:45 +01:00
ar7161_netgear_wndr3800.dts ath79: WNDR3700/3800/MAC: utilize nvmem for caldata fetching 2021-11-06 22:18:45 +01:00
ar7161_netgear_wndr3800ch.dts ath79: WNDR3700/3800/MAC: utilize nvmem for caldata fetching 2021-11-06 22:18:45 +01:00
ar7161_netgear_wndr.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar7161_netgear_wndrmac-v1.dts ath79: WNDR3700/3800/MAC: utilize nvmem for caldata fetching 2021-11-06 22:18:45 +01:00
ar7161_netgear_wndrmac-v2.dts ath79: WNDR3700/3800/MAC: utilize nvmem for caldata fetching 2021-11-06 22:18:45 +01:00
ar7161_siemens_ws-ap3610.dts ath79: move reference clock node to SoC dtsi 2022-11-09 22:55:33 +01:00
ar7161_trendnet_tew-673gru.dts ath79: move reference clock node to SoC dtsi 2022-11-09 22:55:33 +01:00
ar7161_ubnt_routerstation-pro.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7161_ubnt_routerstation.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7161_ubnt_routerstation.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar7240_buffalo_whr-g301n.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar7240_dlink_dir-615-e4.dts ath79: enable UART in SoC DTSI files 2021-02-24 02:53:53 +01:00
ar7240_engenius_enh202-v1.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar7240_netgear_wnr612-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_netgear_wnr612-v2.dtsi ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar7240_netgear_wnr1000-v2.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar7240_on_n150r.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_openmesh_om2p-v1.dts ath79: Add support for OpenMesh OM2P v1 2022-01-16 21:42:19 +01:00
ar7240_ruckus_zf7025.dts ath79: support Ruckus ZoneFlex 7025 2022-11-13 22:36:06 +01:00
ar7240_tplink_tl-wa701nd-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wa730re-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wa801nd-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wa830re-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wa901nd-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wa.dtsi ath79: remove redundant nvmem definitions 2021-08-20 18:13:55 +02:00
ar7240_tplink_tl-wr740n-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wr740n-v3.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wr741-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wr743nd-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wr841-v5.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wr941-v4.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wr.dtsi ath79: remove redundant nvmem definitions 2021-08-20 18:13:55 +02:00
ar7240_tplink.dtsi ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar7240_ubnt_bullet-m-ar7240.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar7241_netgear_wnr2000-v3.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar7241_netgear_wnr2200-8m.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
ar7241_netgear_wnr2200-16m.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
ar7241_netgear_wnr2200.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar7241_tplink_tl-mr3x20.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar7241_tplink_tl-mr3220-v1.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar7241_tplink_tl-mr3420-v1.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar7241_tplink_tl-wr841-v7.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar7241_tplink_tl-wr842n-v1.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar7241_tplink.dtsi ath79: fix MAC address assignment for TP-Link ar7241 devices 2022-11-12 17:10:12 +01:00
ar7241_ubnt_airrouter.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar7241_ubnt_bullet-m-ar7241.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7241_ubnt_nanobridge-m.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7241_ubnt_nanostation-loco-m.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7241_ubnt_nanostation-m.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7241_ubnt_picostation-m.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7241_ubnt_powerbridge-m.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7241_ubnt_rocket-m.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7241_ubnt_unifi-ap-lr.dts ath79: add variant UniFi AP LR 2022-08-06 20:15:30 +02:00
ar7241_ubnt_unifi-ap-outdoor-plus.dts ath79: fix label MAC address for Ubiquiti UniFi AP Outdoor+ 2022-03-30 17:48:30 +02:00
ar7241_ubnt_unifi-ap.dts ath79: rename references of UniFi to UniFi AP 2022-08-06 20:15:30 +02:00
ar7241_ubnt_unifi-ap.dtsi ath79: rename references of UniFi to UniFi AP 2022-08-06 20:15:30 +02:00
ar7241_ubnt_unifi.dtsi ath79: move reference clock node to SoC dtsi 2022-11-09 22:55:33 +01:00
ar7241.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar7242_avm_fritz300e.dts ath79: enable UART in SoC DTSI files 2021-02-24 02:53:53 +01:00
ar7242_buffalo_bhr-4grv.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar7242_buffalo_wzr-bhr.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar7242_buffalo_wzr-hp-g302h-a1a0.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar7242_buffalo_wzr-hp-g450h.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar7242_engenius_eap350-v1.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar7242_engenius_ecb350-v1.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar7242_meraki_mr12.dts ath79: move reference clock node to SoC dtsi 2022-11-09 22:55:33 +01:00
ar7242_tplink_tl-wr2543-v1.dts ath79: calibrate TP-LINK TL-WR2543ND with nvmem 2022-11-27 13:18:29 +01:00
ar7242_ubnt_edgeswitch-5xp.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar7242_ubnt_edgeswitch-8xp.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
ar7242_ubnt_sw.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar7242.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar9132_buffalo_wzr-hp-g300nh-rb.dts ath79: Add support for Buffalo WZR-HP-G300NH 2021-03-22 09:23:10 +01:00
ar9132_buffalo_wzr-hp-g300nh-s.dts ath79: Add support for Buffalo WZR-HP-G300NH 2021-03-22 09:23:10 +01:00
ar9132_buffalo_wzr-hp-g300nh.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar9132_tplink_tl-wa901nd-v2.dts ath79: move reference clock node to SoC dtsi 2022-11-09 22:55:33 +01:00
ar9132_tplink_tl-wr941-v2.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9132_tplink_tl-wr1043nd-v1.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar9132.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar9330_dlink_dir-505.dts ath79: enable UART in SoC DTSI files 2021-02-24 02:53:53 +01:00
ar9330_glinet_gl-ar150.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9330_openmesh_om2p-lc.dts ath79: Add support for OpenMesh OM2P-LC 2020-12-30 23:32:07 +01:00
ar9330_openmesh_om2p-v2.dts ath79: Add support for OpenMesh OM2P v2 2020-12-30 23:32:07 +01:00
ar9330_openmesh_om2p.dtsi ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9330_pqi_air-pen.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9330_ziking_cpe46b.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9330.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar9331_8dev_carambola2.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9331_alfa-network_ap121f.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar9331_alfa-network_ap121f.dtsi ath79: utilize ath9k 'nvmem-cells' on ALFA Network boards 2022-02-27 15:09:36 +01:00
ar9331_alfa-network_ap121fe.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar9331_arduino_yun.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar9331_embeddedwireless_dorin.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9331_etactica_eg200.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9331_glinet_64xx.dtsi ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
ar9331_glinet_6408.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
ar9331_glinet_6416.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
ar9331_glinet_gl-mifi.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9331_glinet_gl-usb150.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9331_hak5_lan-turtle.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar9331_hak5_lan-turtle.dtsi ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9331_hak5_packet-squirrel.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar9331_hak5_wifi-pineapple-nano.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9331_hiwifi_hc6361.dts ath79: port HiWiFi HC6361 from ar71xx 2022-04-16 01:27:09 +00:00
ar9331_onion_omega.dts ath79: add support for onion omega 2021-08-26 15:07:18 +02:00
ar9331_pisen_ts-d084.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9331_pisen_wmm003n.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9331_teltonika_rut230-v1.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9331_tplink_tl-mr10u.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9331_tplink_tl-mr3020-v1.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar9331_tplink_tl-mr3040-v2.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar9331_tplink_tl-wr703n_tl-mr10u.dtsi ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9331_tplink_tl-wr703n.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9331_tplink_tl-wr710n-8m.dtsi ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
ar9331_tplink_tl-wr710n-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9331_tplink_tl-wr710n-v2.1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9331_tplink_tl-wr710n.dtsi ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
ar9331_tplink_tl-wr740n-v4.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9331_tplink_tl-wr740n-v5.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9331_tplink_tl-wr741nd-v4.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9331_tplink_tl-wr741nd-v4.dtsi ath79: fix MAC address assigment for TP-Link TL-WR740N/TL-WR741ND v4 2022-11-20 16:30:27 +01:00
ar9331.dtsi ath79: add missing clock name strings in SoC dtsi 2022-11-09 22:55:33 +01:00
ar9341_engenius_eap300-v2.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9341_engenius_ens202ext-v1.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9341_openmesh_om2p-hs-v1.dts ath79: add support for OpenMesh OM2P-HS v1 2020-12-29 00:03:26 +01:00
ar9341_openmesh_om2p-hs-v2.dts ath79: add support for OpenMesh OM2P-HS v2 2020-12-29 00:03:26 +01:00
ar9341_openmesh_om2p-hs-v3.dts ath79: add support for OpenMesh OM2P-HS v3 2020-12-29 00:03:26 +01:00
ar9341_openmesh_om2p-hs.dtsi ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9341_pcs_cr3000.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9341_pisen_wmb001n.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9341_tplink_tl-mr3420-v2.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar9341_tplink_tl-wa850re-v1.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar9341_tplink_tl-wa860re-v1.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar9341_tplink_tl-wa901nd-v3.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar9341_tplink_tl-wa.dtsi ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9341_tplink_tl-wr841-v8.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
ar9341_tplink_tl-wr842n-v2.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar9341_tplink_tl-wr941nd-v5.dts ath79: add support for TP-Link TL-WR941ND v5 2022-09-11 22:00:22 +02:00
ar9341_tplink.dtsi ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
ar9341.dtsi ath79: do not set inherited phy-mode/status properties again 2020-01-31 13:42:12 +01:00
ar9342_iodata_etg3-r.dts ath79: enable UART in SoC DTSI files 2021-02-24 02:53:53 +01:00
ar9342_mikrotik_routerboard-912uag-2hpnd.dts ath79: fix reference clock for RouterBoard 912UAG 2022-10-23 01:45:52 +02:00
ar9342_ruckus_zf7321.dts ath79: support Ruckus ZoneFlex 7321 2022-09-11 01:36:25 +02:00
ar9342_ubnt_aircube-ac.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
ar9342_ubnt_bullet-ac.dts ath79: Add support for Ubiquiti Bullet AC 2021-01-15 18:32:38 +01:00
ar9342_ubnt_bullet-m-xw.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
ar9342_ubnt_lap-120.dts ath79: create DTSI files for ubnt WA 1-/2-port devices 2020-11-03 18:34:10 +01:00
ar9342_ubnt_litebeam-ac-gen2.dts ath79: remove redundant setup of wmac for ubnt WA devices 2020-11-03 18:34:10 +01:00
ar9342_ubnt_nanobeam-ac-gen2.dts ath79: Add support for Ubiquiti NanoBeam AC Gen2 2020-11-18 21:13:46 +01:00
ar9342_ubnt_nanobeam-ac.dts ath79: Add support for Ubiquiti NanoBeam AC Gen2 2020-11-18 21:13:46 +01:00
ar9342_ubnt_nanobeam-m5-xw.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
ar9342_ubnt_nanostation-ac-loco.dts ath79: remove redundant setup of wmac for ubnt WA devices 2020-11-03 18:34:10 +01:00
ar9342_ubnt_nanostation-ac.dts ath79: remove redundant setup of wmac for ubnt WA devices 2020-11-03 18:34:10 +01:00
ar9342_ubnt_nanostation-loco-m-xw.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
ar9342_ubnt_nanostation-m-xw.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
ar9342_ubnt_powerbeam-5ac-gen2.dts ath79: create DTSI files for ubnt WA 1-/2-port devices 2020-11-03 18:34:10 +01:00
ar9342_ubnt_powerbeam-m2-xw.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
ar9342_ubnt_powerbeam-m5-xw.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
ar9342_ubnt_wa_1port.dtsi ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
ar9342_ubnt_wa_2port.dtsi ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
ar9342_ubnt_wa.dtsi ath9k: OF: qca,disable-(2|5)ghz => ieee80211-freq-limit 2021-10-30 16:32:59 +02:00
ar9342_ubnt_xw.dtsi ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9342_zyxel_nwa11xx.dtsi ath79: add support for ZyXEL NWA1121-NI 2022-08-21 00:09:53 +02:00
ar9342_zyxel_nwa1100-nh.dts ath79: add support for ZyXEL NWA1100-NH 2022-08-21 00:09:53 +02:00
ar9342_zyxel_nwa1121-ni.dts ath79: add support for ZyXEL NWA1121-NI 2022-08-21 00:09:53 +02:00
ar9342_zyxel_nwa1123-ac.dts ath79: add support for ZyXEL NWA1123-AC 2022-08-21 00:09:53 +02:00
ar9342_zyxel_nwa1123-ni.dts ath79: add support for ZyXEL NWA1123-NI 2022-08-21 00:09:53 +02:00
ar9344_aerohive_hiveap-121.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9344_alfa-network_n5q.dts ath79: utilize ath9k 'nvmem-cells' on ALFA Network boards 2022-02-27 15:09:36 +01:00
ar9344_araknis_an-300-ap-i-n.dts ath79: add support for Araknis AN-300-AP-I-N 2022-03-13 19:54:57 +01:00
ar9344_atheros_db120.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar9344_comfast_cf-e120a-v3.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9344_compex_wpj344-16m.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
ar9344_devolo_dlan_wifi.dtsi ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9344_devolo_dlan-pro-1200plus-ac.dts ath79: add support for Devolo dLAN pro 1200+ WiFi ac 2021-06-06 18:56:45 +02:00
ar9344_devolo_magic-2-wifi.dts ath79: add support for Devolo dLAN pro 1200+ WiFi ac 2021-06-06 18:56:45 +02:00
ar9344_dlink_dir-8x5.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar9344_dlink_dir-825-c1.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar9344_dlink_dir-835-a1.dts ath79: enable UART in SoC DTSI files 2021-02-24 02:53:53 +01:00
ar9344_embeddedwireless_balin.dts ath79: add Embedded Wireless Balin Platform 2021-12-03 12:30:08 +01:00
ar9344_engenius_eap600.dts ath79: rename an engenius DTSI to generic senao name 2022-09-11 21:54:00 +02:00
ar9344_engenius_ecb600.dts ath79: rename an engenius DTSI to generic senao name 2022-09-11 21:54:00 +02:00
ar9344_enterasys_ws-ap3705i.dts ath79: drop cs-gpios property 2021-05-01 13:17:57 +02:00
ar9344_mercury_mw4530r-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_mikrotik_routerboard-16m-nor.dtsi ath79: mikrotik: add rw soft_config to extra devices 2022-06-29 12:34:49 +02:00
ar9344_mikrotik_routerboard-lhg-5nd.dts ath79: add support for Mikrotik LHG 5 2022-02-07 00:03:27 +01:00
ar9344_mikrotik_routerboard-sxt-5n.dtsi ath79: cleanup mikrotik routerboot partitions 2022-04-15 07:11:18 +02:00
ar9344_mikrotik_routerboard-sxt-5nd-r2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_netgear_pgzng1.dts ath79: add support for Netgear PGZNG1 2022-06-19 12:31:02 +02:00
ar9344_netgear_r6100.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar9344_netgear_wndr3700-v4.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_netgear_wndr4300.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_netgear_wndr4300sw.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_netgear_wndr4300tn.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_netgear_wndr_usb.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar9344_netgear_wndr_wan.dtsi ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar9344_netgear_wndr.dtsi ath79: calibrate nand netgear wndrxxxx with nvmem 2022-11-20 16:13:48 +01:00
ar9344_ocedo_raccoon.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
ar9344_openmesh_mr600-v1.dts ath79: Add support for OpenMesh MR600 v1 2021-01-19 15:39:36 +01:00
ar9344_openmesh_mr600-v2.dts ath79: Add support for OpenMesh MR600 v2 2021-01-19 15:39:36 +01:00
ar9344_openmesh_mr600.dtsi ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
ar9344_openmesh_om5p-an.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
ar9344_openmesh_om5p.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9344_pcs_cap324.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
ar9344_pcs_cr5000.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar9344_qihoo_c301.dts ath79: enable UART in SoC DTSI files 2021-02-24 02:53:53 +01:00
ar9344_qxwlan_e750a-v4-8m.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9344_qxwlan_e750a-v4-16m.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9344_qxwlan_e750g-v8-8m.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
ar9344_qxwlan_e750g-v8-16m.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
ar9344_qxwlan_e750x.dtsi ath79: enable UART in SoC DTSI files 2021-02-24 02:53:53 +01:00
ar9344_ruckus_zf7372.dts ath79: support Ruckus ZoneFlex 7372 2022-09-11 01:36:25 +02:00
ar9344_samsung_wam250.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9344_senao_ap-dual.dtsi ath79: fix RGMII delay for ar9344 Senao APs 2022-09-11 21:54:00 +02:00
ar9344_teltonika_rut9xx.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar9344_teltonika_rut955-h7v3c0.dts ath79: remove redundant nvmem definitions 2021-08-20 18:13:55 +02:00
ar9344_teltonika_rut955.dts ath79: remove redundant nvmem definitions 2021-08-20 18:13:55 +02:00
ar9344_tplink_cpe210-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_cpe220-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_cpe510-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_cpe510-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_cpe510-v3.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_cpe610-v1.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar9344_tplink_cpe610-v2.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar9344_tplink_cpe_1port.dtsi ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar9344_tplink_cpe_2port.dtsi ath79: remove redundant nvmem definitions 2021-08-20 18:13:55 +02:00
ar9344_tplink_cpe.dtsi ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9344_tplink_tl-wdr3500-v1.dts ath79: calibrate all ar9344 tl-WDRxxxx with nvmem 2022-11-18 20:27:52 +01:00
ar9344_tplink_tl-wdr3600-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_tl-wdr4300-v1-il.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_tl-wdr4300-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_tl-wdr4300.dtsi ath79: calibrate all ar9344 tl-WDRxxxx with nvmem 2022-11-18 20:27:52 +01:00
ar9344_tplink_tl-wdr4310-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_tl-wdrxxxx.dtsi ath79: calibrate all ar9344 tl-WDRxxxx with nvmem 2022-11-18 20:27:52 +01:00
ar9344_tplink_tl-wr841hp-v2.dts ath79: add support for TP-Link TL-WR841HP v2 2022-02-07 00:03:27 +01:00
ar9344_tplink_wbs210-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_wbs210-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_wbs510-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_wbs510-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_ubnt_unifi-ap-pro.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9344_watchguard_ap100.dts ath79: add support for Senao Watchguard AP100 2022-09-11 21:54:00 +02:00
ar9344_watchguard_ap200.dts ath79: add support for Senao WatchGuard AP200 2022-09-11 21:54:00 +02:00
ar9344_wd_mynet-n600.dts ath79: add support for WD My Net N600 2021-12-11 00:50:02 +01:00
ar9344_wd_mynet-n750.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar9344_wd_mynet-nxxx.dtsi ath79: add support for WD My Net N600 2021-12-11 00:50:02 +01:00
ar9344_wd_mynet-wifi-rangeextender.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
ar9344_winchannel_wb2000.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar9344_zbtlink_zbt-wd323.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
ar9344.dtsi ath79: specify device-type for PCI controllers 2021-02-20 01:26:14 +01:00
ath79.dtsi ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca953x_dlink_dap-2xxx.dtsi ath79: D-Link DAP-2xxx (QCA953x): convert ath9k caldata to nvmem 2022-06-18 11:57:21 +02:00
qca953x_tplink_tl-wr810n.dtsi ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca953x.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca955x_dlink_dap-2xxx.dtsi ath79: D-Link DAP-2xxx (QCA955x): convert ath9k caldata to nvmem 2022-06-18 11:54:40 +02:00
qca955x_engenius_ecb1xxx.dtsi ath79: enable UART in SoC DTSI files 2021-02-24 02:53:53 +01:00
qca955x_senao_loader.dtsi ath79: use nvmem-cells for radio calibration of EAP1200H 2022-11-27 13:18:29 +01:00
qca955x_ubnt_xc.dtsi ath79: enable UART in SoC DTSI files 2021-02-24 02:53:53 +01:00
qca955x_zyxel_nbg6x16.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca955x.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca956x.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9531_8dev_lima.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9531_alfa-network_n2q.dts ath79: reduce 'nvmem-cells' definitions on ALFA Network QCA9531 boards 2022-02-27 15:09:36 +01:00
qca9531_alfa-network_pi-wifi4.dts ath79: reduce 'nvmem-cells' definitions on ALFA Network QCA9531 boards 2022-02-27 15:09:36 +01:00
qca9531_alfa-network_r36a.dts ath79: reduce 'nvmem-cells' definitions on ALFA Network QCA9531 boards 2022-02-27 15:09:36 +01:00
qca9531_alfa-network_r36a.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9531_alfa-network_tube-2hq.dts ath79: add support for ALFA Network Tube-2HQ 2022-02-27 16:54:54 +01:00
qca9531_asus_rp-ac51.dts ath79: add support for ASUS RP-AC51 2022-06-30 00:23:42 +02:00
qca9531_comfast_cf-e5.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9531_comfast_cf-e130n-v2.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9531_comfast_cf-e313ac.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9531_comfast_cf-e314n-v2.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9531_comfast_cf-e560ac.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9531_comfast_cf-ew72.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9531_comfast_cf-wr752ac-v1.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9531_compex_wpj531-16m.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9531_dlink_dch-g020-a1.dts ath79: fix various dts warnings 2021-12-11 00:50:02 +01:00
qca9531_engenius_ews511ap.dts ath79: enable UART in SoC DTSI files 2021-02-24 02:53:53 +01:00
qca9531_glinet_gl-ar300m16.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9531_glinet_gl-ar300m-lite.dts ath79: add USB power control for GL-AR300M series 2022-04-30 23:56:47 +02:00
qca9531_glinet_gl-ar300m-nand.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9531_glinet_gl-ar300m-nor.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9531_glinet_gl-ar300m.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9531_glinet_gl-ar750.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9531_glinet_gl-e750.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9531_glinet_gl-x300b.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9531_glinet_gl-x750.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9531_glinet_gl-xe300.dts ath79: improve support for GL.iNet GL-XE300 2022-03-17 21:55:10 +01:00
qca9531_joyit_jt-or750i.dts ath79: fix JT-OR750i switch LED assignment 2021-07-28 14:25:53 +02:00
qca9531_letv_lba-047-ch.dts ath79: add support for Letv LBA-047-CH 2021-11-01 00:15:09 +01:00
qca9531_mikrotik_routerboard-951ui-2nd.dts ath79: add support for MikroTik hAP (RB951Ui-2nD) 2022-05-21 13:54:08 +02:00
qca9531_qxwlan_e600g-v2-8m.dts ath79: add support for Qxwlan E600G v2 / E600GAC v2 2020-11-12 17:18:26 +01:00
qca9531_qxwlan_e600g-v2-16m.dts ath79: add support for Qxwlan E600G v2 / E600GAC v2 2020-11-12 17:18:26 +01:00
qca9531_qxwlan_e600g.dtsi ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9531_qxwlan_e600gac-v2-8m.dts ath79: add support for Qxwlan E600G v2 / E600GAC v2 2020-11-12 17:18:26 +01:00
qca9531_qxwlan_e600gac-v2-16m.dts ath79: add support for Qxwlan E600G v2 / E600GAC v2 2020-11-12 17:18:26 +01:00
qca9531_telco_t1.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9531_teltonika_rut300.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9531_tplink_archer-d50-v1.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9531_tplink_tl-mr3420-v3.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9531_tplink_tl-mr6400-v1.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9531_tplink_tl-wr810n-v1.dts ath79: fix USB power on TP-Link TL-WR810N v1 2021-02-26 13:57:02 +01:00
qca9531_tplink_tl-wr902ac-v1.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9531_wallys_dr531.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9531_yuncore_a770.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9533_comfast_cf-e110n-v2.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9533_dlink_dap-13xx.dtsi ath79: enable UART in SoC DTSI files 2021-02-24 02:53:53 +01:00
qca9533_dlink_dap-1330-a1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_dlink_dap-1365-a1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_dlink_dap-2230-a1.dts ath79: D-Link DAP-2xxx (QCA953x): move art partition to DTSI 2022-06-18 11:57:21 +02:00
qca9533_dlink_dap-3320-a1.dts ath79: D-Link DAP-2xxx (QCA953x): move art partition to DTSI 2022-06-18 11:57:21 +02:00
qca9533_mikrotik_routerboard-16m.dtsi ath79: cleanup mikrotik routerboot partitions 2022-04-15 07:11:18 +02:00
qca9533_mikrotik_routerboard-95x.dtsi ath79: add support for MikroTik RouterBOARD hAP ac lite 2022-05-21 13:54:02 +02:00
qca9533_mikrotik_routerboard-952ui-5ac2nd.dts ath79: add support for MikroTik RouterBOARD hAP ac lite 2022-05-21 13:54:02 +02:00
qca9533_mikrotik_routerboard-lhg-2nd.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_mikrotik_routerboard-lhg-hb.dtsi ath79: enable UART in SoC DTSI files 2021-02-24 02:53:53 +01:00
qca9533_mikrotik_routerboard-map-2nd.dts ath79: add support for RouterBOARD mAP 2022-06-29 12:36:04 +02:00
qca9533_mikrotik_routerboard-mapl-2nd.dts ath79: add support for MikroTik RouterBOARD mAP lite 2022-03-08 18:33:42 +01:00
qca9533_mikrotik_routerboard-wap-2nd.dts ath79: add support for MikroTik RouterBOARD wAP-2nD (wAP) 2022-04-18 07:24:09 +02:00
qca9533_mikrotik_routerboard-wapr-2nd.dts ath79: mikrotik: enable USB module on RouterBoard wAPR-2nD 2021-11-20 21:08:21 +01:00
qca9533_openmesh_om2p-hs-v4.dts ath79: Add support for OpenMesh OM2P-HS v4 2020-12-28 19:37:24 +01:00
qca9533_openmesh_om2p-v4.dts ath79: Add support for OpenMesh OM2P v4 2020-12-28 19:37:24 +01:00
qca9533_openmesh_om2p-v4.dtsi ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9533_plasmacloud_pa300.dts ath79: Add support for Plasma Cloud PA300 2020-12-22 19:11:50 +01:00
qca9533_plasmacloud_pa300.dtsi ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9533_plasmacloud_pa300e.dts ath79: Add support for Plasma Cloud PA300E 2020-12-22 19:11:50 +01:00
qca9533_qca_ap143-8m.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9533_qca_ap143-16m.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9533_qca_ap143.dtsi ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9533_tplink_cpe210-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_cpe210-v3.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_cpe210.dtsi ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9533_tplink_cpe220-v3.dts ath79: remove redundant nvmem definitions 2021-08-20 18:13:55 +02:00
qca9533_tplink_cpexxx.dtsi ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9533_tplink_tl-wa801nd-v3.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wa801nd-v4.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wa801nd.dtsi ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9533_tplink_tl-wa850re-v2.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9533_tplink_tl-wr802n-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wr802n-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wr802n.dtsi ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9533_tplink_tl-wr810n-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wr841-v9.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wr841-v10.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wr841-v11.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wr841-v11.dtsi ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9533_tplink_tl-wr841-v12.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wr841.dtsi ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9533_tplink_tl-wr841hp-v3.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9533_tplink_tl-wr842n-v3.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9533_ubnt_aircube-isp.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9533_yuncore_a930.dts ath79: add support for Yuncore A930 2022-04-15 07:11:18 +02:00
qca9550_airtight_c-75.dts ath79: Add LED labels for Airtight C-75 2022-03-13 12:39:58 +09:00
qca9556_avm_fritz450e.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9556_avm_fritz1750e.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9556_avm_fritz-repeater.dtsi ath79: enable UART in SoC DTSI files 2021-02-24 02:53:53 +01:00
qca9556_avm_fritzdvbc.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9556_mikrotik_routerboard-wap-g-5hact2hnd.dts ath79: cleanup mikrotik routerboot partitions 2022-04-15 07:11:18 +02:00
qca9557_8dev_rambutan.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9557_araknis_an-500-ap-i-ac.dts ath79: add support for Araknis AN-500-AP-I-AC 2022-03-13 19:54:57 +01:00
qca9557_buffalo_bhr-4grv2.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9557_dlink_dap-2660-a1.dts ath79: D-Link DAP-2660 A1: convert ath10k caldata to nvmem 2022-06-18 11:57:21 +02:00
qca9557_dongwon_dw02-412h-64m.dts ath79: improve support for Dongwon T&I DW02-412H 2022-02-01 14:54:16 +09:00
qca9557_dongwon_dw02-412h-128m.dts ath79: improve support for Dongwon T&I DW02-412H 2022-02-01 14:54:16 +09:00
qca9557_dongwon_dw02-412h.dtsi ath79: improve support for Dongwon T&I DW02-412H 2022-02-01 14:54:16 +09:00
qca9557_engenius_eap1200h.dts ath79: use nvmem-cells for radio calibration of EAP1200H 2022-11-27 13:18:29 +01:00
qca9557_engenius_ecb1200.dts ath79: create common DTSI for ECB1200 and ECB1750 2020-12-22 19:11:50 +01:00
qca9557_engenius_enstationac-v1.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9557_extreme-networks_ws-ap3805i.dts ath79: fix model name of Extreme Networks WS-AP3805i 2022-10-08 01:34:28 +02:00
qca9557_iodata_wn-ac1167dgr.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9557_iodata_wn-ac1600dgr2.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9557_iodata_wn-ac1600dgr.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9557_iodata_wn-ac-dgr.dtsi ath79: enable UART in SoC DTSI files 2021-02-24 02:53:53 +01:00
qca9557_zyxel_nbg6616.dts ath79: drop num-cs for SPI controller 2020-12-04 15:50:24 +01:00
qca9558_allnet_all-wap02860ac.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9558_araknis_an-700-ap-i-ac.dts ath79: add support for Araknis AN-700-AP-I-AC 2022-03-13 19:54:58 +01:00
qca9558_belkin_f9j1108-v2.dts ath79: create shared DTSI/definition for Belkin F9J1108/F9K1115 v2 2020-12-14 16:57:21 +01:00
qca9558_belkin_f9k1115-v2.dts ath79: add support for the Belkin F9K1115 v2 (AC1750 DB Wi-Fi) 2020-12-14 16:59:49 +01:00
qca9558_belkin_f9x-v2.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9558_comfast_cf-wr650ac-v1.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9558_comfast_cf-wr650ac-v2.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9558_comfast_cf-wr650ac.dtsi ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9558_compex_wpj558-16m.dts ath79: add support for Compex WPJ558 (16M) 2021-08-25 01:42:17 +02:00
qca9558_devolo_dvl1xxx.dtsi ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9558_devolo_dvl1200e.dts ath79: remove redundant nvmem definitions 2021-08-20 18:13:55 +02:00
qca9558_devolo_dvl1200i.dts ath79: move device specific nodes to DTS files for Devolo 1xxx 2020-11-24 14:40:55 +01:00
qca9558_devolo_dvl1750c.dts ath79: move device specific nodes to DTS files for Devolo 1xxx 2020-11-24 14:40:55 +01:00
qca9558_devolo_dvl1750e.dts ath79: remove redundant nvmem definitions 2021-08-20 18:13:55 +02:00
qca9558_devolo_dvl1750i.dts ath79: move device specific nodes to DTS files for Devolo 1xxx 2020-11-24 14:40:55 +01:00
qca9558_devolo_dvl1750x.dts ath79: move device specific nodes to DTS files for Devolo 1xxx 2020-11-24 14:40:55 +01:00
qca9558_dlink_dap-2680-a1.dts ath79: D-Link DAP-2680 A1: convert ath10k caldata to nvmem 2022-06-18 11:57:19 +02:00
qca9558_dlink_dap-2695-a1.dts ath79: D-Link DAP-2695 A1: convert ath10k caldata to nvmem 2022-06-18 11:57:21 +02:00
qca9558_dlink_dap-3662-a1.dts ath79: D-Link DAP-3662 A1: convert ath10k caldata to nvmem 2022-06-18 11:57:21 +02:00
qca9558_domywifi_dw33d.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9558_engenius_eap1750h.dts ath79: add support for Senao Engenius EAP1750H 2022-11-27 13:18:29 +01:00
qca9558_engenius_ecb1750.dts ath79: create common DTSI for ECB1200 and ECB1750 2020-12-22 19:11:50 +01:00
qca9558_engenius_epg5000.dts ath79: enable UART in SoC DTSI files 2021-02-24 02:53:53 +01:00
qca9558_jjplus_jwap230.dts ath79: add support for jjPlus JWAP230 2021-12-11 00:50:02 +01:00
qca9558_librerouter_librerouter-v1.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9558_linksys_ea4500-v3.dts ath79: add support for Linksys EA4500 v3 2022-10-30 23:14:45 +01:00
qca9558_mikrotik_routerboard-92x.dtsi ath79: cleanup mikrotik routerboot partitions 2022-04-15 07:11:18 +02:00
qca9558_mikrotik_routerboard-96x.dtsi ath79: mikrotik: add rw soft_config to extra devices 2022-06-29 12:34:49 +02:00
qca9558_mikrotik_routerboard-921gs-5hpacd-15s.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9558_mikrotik_routerboard-922uags-5hpacd.dts ath79: mikrotik: enable SFP on RB921GS-5HPacD (mANTBox 15s) 2021-10-31 21:24:47 +01:00
qca9558_mikrotik_routerboard-962uigs-5hact2hnt.dts ath79: add support for MikroTik RouterBOARD 962UiGS-5HacT2HnT (hAP ac) 2022-04-16 16:59:29 +02:00
qca9558_netgear_ex6400.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9558_netgear_ex7300.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9558_netgear_ex7300.dtsi ath79: move reference clock node to SoC dtsi 2022-11-09 22:55:33 +01:00
qca9558_ocedo_koala.dts ath79: move reference clock node to SoC dtsi 2022-11-09 22:55:33 +01:00
qca9558_ocedo_ursus.dts ath79: move reference clock node to SoC dtsi 2022-11-09 22:55:33 +01:00
qca9558_openmesh_a40.dts ath79: Add support for OpenMesh A40 2021-06-05 01:17:11 +02:00
qca9558_openmesh_a60.dts ath79: Add support for OpenMesh A60 2021-06-05 01:17:11 +02:00
qca9558_openmesh_a60.dtsi ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9558_openmesh_mr900-v1.dts ath79: remove redundant nvmem definitions 2021-08-20 18:13:55 +02:00
qca9558_openmesh_mr900-v2.dts ath79: remove redundant nvmem definitions 2021-08-20 18:13:55 +02:00
qca9558_openmesh_mr1750-v1.dts ath79: Add support for OpenMesh MR1750 v1 2021-01-19 21:41:26 +01:00
qca9558_openmesh_mr1750-v2.dts ath79: Add support for OpenMesh MR1750 v2 2021-01-19 21:41:26 +01:00
qca9558_openmesh_mr.dtsi ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9558_openmesh_om5p-ac-v1.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9558_openmesh_om5p-ac-v2.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9558_qxwlan_e558-v2-8m.dts ath79: add support for Qxwlan E558 v2 2020-10-17 20:17:59 +02:00
qca9558_qxwlan_e558-v2-16m.dts ath79: add support for Qxwlan E558 v2 2020-10-17 20:17:59 +02:00
qca9558_qxwlan_e558.dtsi ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9558_sitecom_wlr-8100.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9558_sophos_ap15.dts ath79: add support for Sophos AP15 2022-08-06 20:33:59 +02:00
qca9558_sophos_ap55.dts ath79: add support for Sophos AP100/AP55 family 2022-04-16 16:59:29 +02:00
qca9558_sophos_ap55c.dts ath79: add support for Sophos AP100/AP55 family 2022-04-16 16:59:29 +02:00
qca9558_sophos_ap100.dts ath79: add support for Sophos AP100/AP55 family 2022-04-16 16:59:29 +02:00
qca9558_sophos_ap100c.dts ath79: add support for Sophos AP100/AP55 family 2022-04-16 16:59:29 +02:00
qca9558_sophos_ap.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9558_tplink_archer-c5-v1.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9558_tplink_archer-c7-v1.dts ath79: convert TP-Link Archer C7v1/2 Wifis to nvmem-cells 2021-11-28 01:13:08 +01:00
qca9558_tplink_archer-c7-v2.dts ath79: convert TP-Link Archer C7v1/2 Wifis to nvmem-cells 2021-11-28 01:13:08 +01:00
qca9558_tplink_archer-c.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9558_tplink_archer-d7-v1.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9558_tplink_archer-d7.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9558_tplink_archer-d7b-v1.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9558_tplink_re350k-v1.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9558_tplink_re355-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9558_tplink_re450-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9558_tplink_rex5x.dtsi ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9558_tplink_tl-wdr4900-v2.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9558_tplink_tl-wdr7500-v3.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9558_tplink_tl-wr941n-v7-cn.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9558_tplink_tl-wr1043nd-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9558_tplink_tl-wr1043nd-v3.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9558_tplink_tl-wr1043nd.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9558_tplink_tl-wr1045nd-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9558_trendnet_tew-823dru.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9558_ubnt_nanobeam-ac-xc.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9558_ubnt_powerbeam-5ac-500.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9558_ubnt_rocket-5ac-lite.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9558_watchguard_ap300.dts ath79: add support for Senao WatchGuard AP300 2022-09-11 21:54:00 +02:00
qca9558_zyxel_emg2926_q10a.dts ath79: add Zyxel EMG2926-Q10A 2022-02-26 13:36:30 +01:00
qca9558_zyxel_nbg6716.dts ath79: drop num-cs for SPI controller 2020-12-04 15:50:24 +01:00
qca9561_avm_fritz4020.dts ath79: enable UART in SoC DTSI files 2021-02-24 02:53:53 +01:00
qca9561_nec_wf1200cr.dts ath79: add support for NEC Aterm WF1200CR 2021-06-06 21:21:51 +02:00
qca9561_tplink_archer-c5x.dtsi ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9561_tplink_archer-c6x.dtsi ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9561_tplink_archer-c25-v1.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9561_tplink_archer-c58-v1.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9561_tplink_archer-c59-v1.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9561_tplink_archer-c59-v2.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9561_tplink_archer-c60-v1.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9561_tplink_archer-c60-v2.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9561_tplink_archer-c60-v3.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9561_tplink_eap225-wall-v2.dts ath79: TP-Link EAP225-Wall v2: use pre-calibration nvmem-cell 2022-06-18 19:30:44 +02:00
qca9561_xiaomi_mi-router-4q.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
qca9563_asus_pl-ac56.dts ath79: add support for ASUS PL-AC56 2022-06-30 00:16:59 +02:00
qca9563_asus_rp-ac66.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9563_comfast_cf-e375ac.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9563_compex_wpj563.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9563_dlink_dir-842-c1.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9563_dlink_dir-842-c2.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9563_dlink_dir-842-c3.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9563_dlink_dir-842-c.dtsi ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9563_dlink_dir-859-a1.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9563_elecom_wrc-300ghbk2-i.dts ath79: use NVMEM for wlan caldata on ELECOM devices 2022-10-19 22:58:12 +02:00
qca9563_elecom_wrc-1750ghbk2-i.dts ath79: use NVMEM for wlan caldata on ELECOM devices 2022-10-19 22:58:12 +02:00
qca9563_elecom_wrc-ghbk2-i.dtsi ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9563_glinet_gl-ar750s-nor-nand.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9563_glinet_gl-ar750s-nor.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9563_glinet_gl-ar750s.dtsi ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9563_nec_wg800hp.dts ath79: enable UART in SoC DTSI files 2021-02-24 02:53:53 +01:00
qca9563_nec_wg1200cr.dts ath79: enable UART in SoC DTSI files 2021-02-24 02:53:53 +01:00
qca9563_netgear_wndr4300-v2.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9563_netgear_wndr4500-v3.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9563_netgear_wndr.dtsi ath79: calibrate nand netgear wndrxxxx with nvmem 2022-11-20 16:13:48 +01:00
qca9563_phicomm_k2t.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9563_qxwlan_e1700ac-v2-8m.dts ath79: add support for Qxwlan E1700AC v2 2020-10-17 20:18:00 +02:00
qca9563_qxwlan_e1700ac-v2-16m.dts ath79: add support for Qxwlan E1700AC v2 2020-10-17 20:18:00 +02:00
qca9563_qxwlan_e1700ac.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9563_rosinson_wr818.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9563_tplink_archer-a7-v5.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9563_tplink_archer-c2-v3.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9563_tplink_archer-c6-v2-us.dts ath79: tplink-archer-c6-v2-us: fix inverted LED colors 2022-07-12 09:25:43 +02:00
qca9563_tplink_archer-c6-v2.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9563_tplink_archer-c7-v4.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9563_tplink_archer-c7-v5.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9563_tplink_archer-x6-v2.dtsi ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9563_tplink_archer-x7-v5.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9563_tplink_cpe710-v1.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9563_tplink_deco-m4r-v1.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9563_tplink_deco-s4-v2.dts ath79: add support for TP-Link Deco S4 2022-09-11 21:54:00 +02:00
qca9563_tplink_eap2x5-1port.dtsi ath79: move ethernet phy node for TP-Link EAP devices 2022-06-16 21:39:32 +02:00
qca9563_tplink_eap225-outdoor-v1.dts ath79: TP-Link EAP225-Outdoor v1: use pre-calibration nvmem-cell 2022-06-18 19:30:44 +02:00
qca9563_tplink_eap225-outdoor-v3.dts ath79: support for TP-Link EAP225-Outdoor v3 2022-06-22 17:47:11 +02:00
qca9563_tplink_eap225-v1.dts ath79: move ethernet phy node for TP-Link EAP devices 2022-06-16 21:39:32 +02:00
qca9563_tplink_eap225-v3.dts ath79: TP-Link EAP225 v3: use pre-calibration nvmem-cell 2022-06-18 19:30:44 +02:00
qca9563_tplink_eap225-v4.dts ath79: support for TP-Link EAP225 v4 2022-06-28 10:58:16 +02:00
qca9563_tplink_eap245-v1.dts ath79: move ethernet phy node for TP-Link EAP devices 2022-06-16 21:39:32 +02:00
qca9563_tplink_eap245-v3.dts ath79: TP-Link EAP245 v3: use pre-calibration nvmem-cell 2022-06-18 09:36:21 +02:00
qca9563_tplink_re450-v2.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9563_tplink_re450-v3.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9563_tplink_re450.dtsi ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9563_tplink_re455-v1.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9563_tplink_tl-wa1201-v2.dts ath79: add support for TP-Link TL-WA1201 v2 2021-09-05 23:52:35 +02:00
qca9563_tplink_tl-wpa8630-v1.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9563_tplink_tl-wpa8630.dtsi ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9563_tplink_tl-wpa8630p-v2-int.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9563_tplink_tl-wpa8630p-v2.0-eu.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9563_tplink_tl-wpa8630p-v2.1-eu.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9563_tplink_tl-wr1043n-v5.dts ath79: convert remaining mtd-mac-address cases to nvmem 2021-08-18 23:46:02 +02:00
qca9563_tplink_tl-wr1043n.dtsi ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9563_tplink_tl-wr1043nd-v4.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9563_ubnt_unifiac-lite.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9563_ubnt_unifiac-lite.dtsi ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9563_ubnt_unifiac-lr.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9563_ubnt_unifiac-mesh-pro.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9563_ubnt_unifiac-mesh.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9563_ubnt_unifiac-pro.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9563_ubnt_unifiac-pro.dtsi ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9563_ubnt_unifiac.dtsi ath79: remove redundant nvmem definitions 2021-08-20 18:13:55 +02:00
qca9563_xiaomi_aiot-ac2350.dts ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9563_yuncore_a782.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9563_yuncore_xd3200.dts ath79: add support for Yuncore XD3200 2022-04-15 07:11:18 +02:00
qca9563_yuncore_xd4200.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9563_yuncore_xd4200.dtsi ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9563_zte_mf281.dts ath79: add support for ZTE MF281 2022-09-08 13:57:18 +02:00
qca9563_zte_mf286.dts ath79: support ZTE MF286A/R 2022-02-26 17:46:10 +01:00
qca9563_zte_mf286.dtsi ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9563_zte_mf286a.dts ath79: support ZTE MF286A/R 2022-02-26 17:46:10 +01:00
qca9563_zte_mf286ar.dtsi ath79: support ZTE MF286A/R 2022-02-26 17:46:10 +01:00
qca9563_zte_mf286r.dts ath79: support ZTE MF286A/R 2022-02-26 17:46:10 +01:00
qcn5502_netgear_ex7300-v2.dts ath79: move reference clock node to SoC dtsi 2022-11-09 22:55:33 +01:00
qcn5502_tplink_archer-a9-v6.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
tp9343_tplink_tl-wa901nd-v4.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
tp9343_tplink_tl-wa901nd-v5.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
tp9343_tplink_tl-wa901nd.dtsi ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
tp9343_tplink_tl-wr94x.dtsi ath79: add support for TP-Link TL-WA901ND v4 and v5 2020-05-18 13:35:38 +02:00
tp9343_tplink_tl-wr940n-v3.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
tp9343_tplink_tl-wr940n-v3.dtsi ath79: remove redundant nvmem definitions 2021-08-20 18:13:55 +02:00
tp9343_tplink_tl-wr940n-v4.dts ath79: remove redundant nvmem definitions 2021-08-20 18:13:55 +02:00
tp9343_tplink_tl-wr940n-v6.dts ath79: remove redundant nvmem definitions 2021-08-20 18:13:55 +02:00
tp9343_tplink_tl-wr941hp-v1.dts ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
tp9343_tplink_tl-wr941nd-v6.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
tp9343_tplink_tl-wx.dtsi ath79: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00