immortalwrt/target/linux/ath79/image
Sven Eckelmann 9fe5be7f08 ath79: Add support for OpenMesh OM5P-AC v1
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
  - eth0
    + AR8035 ethernet PHY (RGMII)
    + 10/100/1000 Mbps Ethernet
    + 802.3af POE
    + used as LAN interface
  - eth1
    + AR8035 ethernet PHY (SGMII)
    + 10/100/1000 Mbps Ethernet
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-01-13 12:39:17 +08:00
..
bin ath79: update upsteam 2019-12-02 05:55:49 -08:00
lzma-loader ath79: lzma-loader: allow setting custom kernel magic 2021-04-08 23:11:52 +08:00
common-buffalo.mk ath79: use common device definition for Buffalo devices 2020-09-17 11:47:27 +08:00
common-mikrotik.mk treewide: call check-size before append-metadata 2021-07-11 12:13:31 +08:00
common-netgear.mk treewide: call check-size before append-metadata 2021-07-11 12:13:31 +08:00
common-senao.mk ath79: add recipe for common setup with loader-okli-compile 2021-10-09 00:04:10 +08:00
common-tp-link.mk treewide: call check-size before append-metadata 2021-07-11 12:13:31 +08:00
common-yuncore.mk ath79: update upsteam 2019-12-02 05:55:49 -08:00
generic-tp-link.mk ath79: add support for TP-Link CPE710-v1 2021-09-27 23:56:37 +08:00
generic-ubnt.mk ath79: add support for Ubiquiti PowerBeam M2 (XW) 2021-08-23 12:04:27 +08:00
generic.mk ath79: Add support for OpenMesh OM5P-AC v1 2022-01-13 12:39:17 +08:00
Makefile ath79: append/prepad okli kernel support 2022-01-09 16:10:34 +08:00
mikrotik.mk ath79: mikrotik: enable SFP on RB921GS-5HPacD (mANTBox 15s) 2021-11-02 00:08:49 +08:00
nand.mk ath79: add support for Netgear R6100 2021-12-22 11:24:08 +08:00
tiny-netgear.mk ath79: netgear: trim down uImage customisations 2020-11-28 18:53:21 +08:00
tiny-tp-link.mk ath79: sync with upstream source 2020-09-06 19:53:51 +08:00
tiny.mk treewide: call check-size before append-metadata 2021-07-11 12:13:31 +08:00