a49f023eb7
RAISECOM MSG1500 X.00 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router.
Apart from the general model, there are two ISP customized models:
China Mobile and China Telecom.
Specifications:
- SoC: Mediatek MT7621AT
- RAM: 256MiB DDR3
- Flash: 128MiB NAND
- Ethernet: 5 * 10/100/1000Mbps: 4 * LAN + 1 * WAN
- Switch: MediaTek MT7530 (SoC)
- WLAN: 1 * MT7615DN Dual-Band 2.4GHz 2T2R (400Mbps) 5GHz 2T2R (867Mbps)
- USB: 1 * USB 2.0 port
- Button: 1 * RESET button, 1 * WPS button, 1 * WIFI button
- LED: blue color: POWER, WAN, WPS, 2.4G, 5G, LAN1, LAN2, LAN3, LAN4, USB
- UART: 1 * serial port header (4-pin)
- Power: DC 12V, 1A
- Switch: 1 * POWER switch
MAC addresses as verified by vendor firmware:
use address source
LAN C8:XX:XX:3A:XX:E7 Config "protest_lan_mac" ascii (label)
WAN C8:XX:XX:3A:XX:EA Config "protest_wan_mac" ascii
5G C8:XX:XX:3A:XX:E8 Factory "0x4" hex
2.4G CA:XX:XX:4A:XX:E8 [not on flash]
The increment of the 4th byte for the 2.4g address appears to vary.
Reported cases:
5g 2.4g increment
C8:XX:XX:90:XX:C3 CA:XX:XX:C0:XX:C3 0x30
C8:XX:XX:3A:XX:08 CA:XX:XX:4A:XX:08 0x10
C8:XX:XX:3A:XX:E8 CA:XX:XX:4A:XX:E8 0x10
Since increment is inconsistent and there is no obvious pattern
in swapping bytes, and the 2.4g address has local bit set anyway,
it seems safer to use the LAN address with flipped byte here in
order to prevent collisions between OpenWrt devices and OEM devices
for this interface. This way we at least use an address as base
that is definitely owned by the device at hand.
Notes:
1. The vendor firmware allows you to connect to the router by telnet.
(known version 1.0.0 can open telnet.)
There is no official binary firmware available.
Backup the important partitions data:
"Bootloader", "Config", "Factory", and "firmware".
Note that with the vendor firmware the memory is detected only 128MiB
and the last 512KiB in NAND flash is not used.
2. The POWER LED is default on after press POWER switch.
The WAN and LAN1 - 4 LEDs are wired to ethernet switch.
The WPS LED is controlled by MT7615DN's GPIO.
Currently there is no proper way to configure it.
3. At the time of adding support the wireless config needs to be set up
by editing the wireless config file:
* Setting the country code is mandatory, otherwise the router loses
connectivity at the next reboot. This is mandatory and can be done
from luci. After setting the country code the router boots correctly.
A reset with the reset button will fix the issue and the user has to
reconfigure.
* This is minor since the 5g interface does not come up online although
it is not set as disabled. 2 options here:
1- Either run the "wifi" command. Can be added from LuCI in system -
startup - local startup and just add wifi above "exit 0".
2- Or add the serialize option in the wireless config file as shown
below. This one would work and bring both interfaces automatically
at every boot:
config wifi-device 'radio0'
option serialize '1'
config wifi-device 'radio1'
option serialize '1'
Flash instructions using initramfs image:
1. Press POWER switch to power down if the router is running.
2. Connect PC to one of LAN ports, and set
static IP address to "10.10.10.2", netmask to "255.255.255.0",
and gateway to "10.10.10.1" manually on the PC.
3. Push and hold the WIFI button, and then power up the router.
After about 10s (or you can call the recovery page, see "4" below)
you can release the WIFI button.
There is no clear indication when the router
is entering or has entered into "RAISECOM Router Recovery Mode".
4. Call the recovery page for the router at "http://10.10.10.1".
Keep an eye on the "WARNING!! tip" of the recovery page.
Click "Choose File" to select initramfs image, then click "Upload".
5. If image is uploaded successfully, you will see the page display
"Device is upgrading the firmware... %".
Keep an eye on the "WARNING!! tip" of the recovery page.
When the page display "Upgrade Successfully",
you can set IP address as "automatically obtain".
6. After the rebooting (PC should automatically obtain an IP address),
open the SSH connection, then download the sysupgrade image
to the router and perform sysupgrade with it.
Flash back to vendor firmware:
See "Flash instructions 1 - 5" above.
The only difference is that in step 4
you should select the vendor firmware which you backup.
Signed-off-by: Liangkuan Yang <ylk951207@gmail.com>
(cherry picked from commit bc7d36ba3a)
1816 lines
50 KiB
Makefile
1816 lines
50 KiB
Makefile
#
|
|
# MT7621 Profiles
|
|
#
|
|
|
|
include ./common-tp-link.mk
|
|
|
|
DEFAULT_SOC := mt7621
|
|
|
|
KERNEL_DTB += -d21
|
|
DEVICE_VARS += ELECOM_HWNAME LINKSYS_HWNAME
|
|
|
|
define Build/elecom-wrc-gs-factory
|
|
$(eval product=$(word 1,$(1)))
|
|
$(eval version=$(word 2,$(1)))
|
|
$(eval hash_opt=$(word 3,$(1)))
|
|
$(STAGING_DIR_HOST)/bin/mkhash md5 $(hash_opt) $@ >> $@
|
|
( \
|
|
echo -n "ELECOM $(product) v$(version)" | \
|
|
dd bs=32 count=1 conv=sync; \
|
|
dd if=$@; \
|
|
) > $@.new
|
|
mv $@.new $@
|
|
endef
|
|
|
|
define Build/gemtek-trailer
|
|
printf "%s%08X" ".GEMTEK." "$$(cksum $@ | cut -d ' ' -f1)" >> $@
|
|
endef
|
|
|
|
define Build/h3c-blank-header
|
|
dd if=/dev/zero of=$@.blank bs=160 count=1
|
|
cat $@ >> $@.blank
|
|
mv $@.blank $@
|
|
endef
|
|
|
|
define Build/iodata-factory
|
|
$(eval fw_size=$(word 1,$(1)))
|
|
$(eval fw_type=$(word 2,$(1)))
|
|
$(eval product=$(word 3,$(1)))
|
|
$(eval factory_bin=$(word 4,$(1)))
|
|
if [ -e $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) -a "$$(stat -c%s $@)" -lt "$(fw_size)" ]; then \
|
|
$(CP) $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) $(factory_bin); \
|
|
$(STAGING_DIR_HOST)/bin/mksenaofw \
|
|
-r 0x30a -p $(product) -t $(fw_type) \
|
|
-e $(factory_bin) -o $(factory_bin).new; \
|
|
mv $(factory_bin).new $(factory_bin); \
|
|
$(CP) $(factory_bin) $(BIN_DIR)/; \
|
|
else \
|
|
echo "WARNING: initramfs kernel image too big, cannot generate factory image" >&2; \
|
|
fi
|
|
endef
|
|
|
|
define Build/iodata-mstc-header
|
|
( \
|
|
data_size_crc="$$(dd if=$@ ibs=64 skip=1 2>/dev/null | gzip -c | \
|
|
tail -c 8 | od -An -tx8 --endian little | tr -d ' \n')"; \
|
|
echo -ne "$$(echo $$data_size_crc | sed 's/../\\x&/g')" | \
|
|
dd of=$@ bs=8 count=1 seek=7 conv=notrunc 2>/dev/null; \
|
|
)
|
|
dd if=/dev/zero of=$@ bs=4 count=1 seek=1 conv=notrunc 2>/dev/null
|
|
( \
|
|
header_crc="$$(dd if=$@ bs=64 count=1 2>/dev/null | gzip -c | \
|
|
tail -c 8 | od -An -N4 -tx4 --endian little | tr -d ' \n')"; \
|
|
echo -ne "$$(echo $$header_crc | sed 's/../\\x&/g')" | \
|
|
dd of=$@ bs=4 count=1 seek=1 conv=notrunc 2>/dev/null; \
|
|
)
|
|
endef
|
|
|
|
define Build/ubnt-erx-factory-image
|
|
if [ -e $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) -a "$$(stat -c%s $@)" -lt "$(KERNEL_SIZE)" ]; then \
|
|
echo '21001:7' > $(1).compat; \
|
|
$(TAR) -cf $(1) --transform='s/^.*/compat/' $(1).compat; \
|
|
\
|
|
$(TAR) -rf $(1) --transform='s/^.*/vmlinux.tmp/' $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE); \
|
|
mkhash md5 $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) > $(1).md5; \
|
|
$(TAR) -rf $(1) --transform='s/^.*/vmlinux.tmp.md5/' $(1).md5; \
|
|
\
|
|
echo "dummy" > $(1).rootfs; \
|
|
$(TAR) -rf $(1) --transform='s/^.*/squashfs.tmp/' $(1).rootfs; \
|
|
\
|
|
mkhash md5 $(1).rootfs > $(1).md5; \
|
|
$(TAR) -rf $(1) --transform='s/^.*/squashfs.tmp.md5/' $(1).md5; \
|
|
\
|
|
echo '$(BOARD) $(VERSION_CODE) $(VERSION_NUMBER)' > $(1).version; \
|
|
$(TAR) -rf $(1) --transform='s/^.*/version.tmp/' $(1).version; \
|
|
\
|
|
$(CP) $(1) $(BIN_DIR)/; \
|
|
else \
|
|
echo "WARNING: initramfs kernel image too big, cannot generate factory image" >&2; \
|
|
fi
|
|
endef
|
|
|
|
define Build/zytrx-header
|
|
$(eval board=$(word 1,$(1)))
|
|
$(eval version=$(word 2,$(1)))
|
|
$(STAGING_DIR_HOST)/bin/zytrx -B '$(board)' -v '$(version)' -i $@ -o $@.new
|
|
mv $@.new $@
|
|
endef
|
|
|
|
define Device/dsa-migration
|
|
DEVICE_COMPAT_VERSION := 1.1
|
|
DEVICE_COMPAT_MESSAGE := Config cannot be migrated from swconfig to DSA
|
|
endef
|
|
|
|
define Device/adslr_g7
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := ADSLR
|
|
DEVICE_MODEL := G7
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += adslr_g7
|
|
|
|
define Device/afoundry_ew1200
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := AFOUNDRY
|
|
DEVICE_MODEL := EW1200
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-mt76x2 kmod-mt7603 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += ew1200
|
|
endef
|
|
TARGET_DEVICES += afoundry_ew1200
|
|
|
|
define Device/alfa-network_quad-e4g
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := ALFA Network
|
|
DEVICE_MODEL := Quad-E4G
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-usb3 uboot-envtools \
|
|
-wpad-openssl
|
|
SUPPORTED_DEVICES += quad-e4g
|
|
endef
|
|
TARGET_DEVICES += alfa-network_quad-e4g
|
|
|
|
define Device/ampedwireless_ally_common
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := Amped Wireless
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware uboot-envtools
|
|
IMAGE_SIZE := 32768k
|
|
KERNEL_SIZE := 4096k
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
UBINIZE_OPTS := -E 5
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | uImage lzma -n 'flashable-initramfs' |\
|
|
edimax-header -s CSYS -m RN68 -f 0x001c0000 -S 0x01100000
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
|
|
define Device/ampedwireless_ally-r1900k
|
|
$(Device/ampedwireless_ally_common)
|
|
DEVICE_MODEL := ALLY-R1900K
|
|
DEVICE_PACKAGES += kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += ampedwireless_ally-r1900k
|
|
|
|
define Device/ampedwireless_ally-00x19k
|
|
$(Device/ampedwireless_ally_common)
|
|
DEVICE_MODEL := ALLY-00X19K
|
|
endef
|
|
TARGET_DEVICES += ampedwireless_ally-00x19k
|
|
|
|
define Device/asiarf_ap7621-001
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16000k
|
|
DEVICE_VENDOR := AsiaRF
|
|
DEVICE_MODEL := AP7621-001
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 -wpad-openssl
|
|
endef
|
|
TARGET_DEVICES += asiarf_ap7621-001
|
|
|
|
define Device/asiarf_ap7621-nv1
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16000k
|
|
DEVICE_VENDOR := AsiaRF
|
|
DEVICE_MODEL := AP7621-NV1
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 -wpad-openssl
|
|
endef
|
|
TARGET_DEVICES += asiarf_ap7621-nv1
|
|
|
|
define Device/asus_rt-ac57u
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := RT-AC57U
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += asus_rt-ac57u
|
|
|
|
define Device/asus_rt-ac65p
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := RT-AC65P
|
|
IMAGE_SIZE := 51200k
|
|
UBINIZE_OPTS := -E 5
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-mt7615e kmod-mt7615-firmware uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += asus_rt-ac65p
|
|
|
|
define Device/asus_rt-ac85p
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := RT-AC85P
|
|
IMAGE_SIZE := 51200k
|
|
UBINIZE_OPTS := -E 5
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-mt7615e kmod-mt7615-firmware uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += asus_rt-ac85p
|
|
|
|
define Device/asus_rt-n56u-b1
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := RT-N56U
|
|
DEVICE_VARIANT := B1
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += asus_rt-n56u-b1
|
|
|
|
define Device/buffalo_wsr-1166dhp
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE/sysupgrade.bin := trx | pad-rootfs | append-metadata
|
|
IMAGE_SIZE := 15936k
|
|
DEVICE_VENDOR := Buffalo
|
|
DEVICE_MODEL := WSR-1166DHP
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
|
|
SUPPORTED_DEVICES += wsr-1166
|
|
endef
|
|
TARGET_DEVICES += buffalo_wsr-1166dhp
|
|
|
|
define Device/buffalo_wsr-2533dhpl
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 7936k
|
|
DEVICE_VENDOR := Buffalo
|
|
DEVICE_MODEL := WSR-2533DHPL
|
|
DEVICE_ALT0_VENDOR := Buffalo
|
|
DEVICE_ALT0_MODEL := WSR-2533DHP
|
|
IMAGE/sysupgrade.bin := trx | pad-rootfs | append-metadata
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
DEFAULT := n
|
|
endef
|
|
TARGET_DEVICES += buffalo_wsr-2533dhpl
|
|
|
|
define Device/buffalo_wsr-600dhp
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Buffalo
|
|
DEVICE_MODEL := WSR-600DHP
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-rt2800-pci
|
|
SUPPORTED_DEVICES += wsr-600
|
|
endef
|
|
TARGET_DEVICES += buffalo_wsr-600dhp
|
|
|
|
define Device/cudy_wr1300
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 15872k
|
|
DEVICE_VENDOR := Cudy
|
|
DEVICE_MODEL := WR1300
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += cudy_wr1300
|
|
|
|
define Device/cudy_wr2100
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := Cudy
|
|
DEVICE_MODEL := WR2100
|
|
IMAGE_SIZE := 15872k
|
|
UIMAGE_NAME := R11
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += cudy_wr2100
|
|
|
|
define Device/dlink_dir-8xx-a1
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16000k
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
KERNEL_INITRAMFS := $$(KERNEL) | uimage-padhdr 96
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | uimage-padhdr 96 |\
|
|
pad-rootfs | append-metadata | check-size
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | uimage-padhdr 96 |\
|
|
check-size
|
|
endef
|
|
|
|
define Device/dlink_dir-8xx-r1
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
KERNEL_INITRAMFS := $$(KERNEL)
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs |\
|
|
pad-rootfs | append-metadata | check-size
|
|
endef
|
|
|
|
define Device/dlink_dir-xx60-a1
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 40960k
|
|
UBINIZE_OPTS := -E 5
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
KERNEL := $$(KERNEL) | uimage-padhdr 96
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
endef
|
|
|
|
define Device/dlink_dir-1960-a1
|
|
$(Device/dlink_dir-xx60-a1)
|
|
DEVICE_MODEL := DIR-1960
|
|
DEVICE_VARIANT := A1
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-1960-a1
|
|
|
|
define Device/dlink_dir-2640-a1
|
|
$(Device/dlink_dir-xx60-a1)
|
|
DEVICE_MODEL := DIR-2640
|
|
DEVICE_VARIANT := A1
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-2640-a1
|
|
|
|
define Device/dlink_dir-2660-a1
|
|
$(Device/dlink_dir-xx60-a1)
|
|
DEVICE_MODEL := DIR-2660
|
|
DEVICE_VARIANT := A1
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-2660-a1
|
|
|
|
define Device/dlink_dir-860l-b1
|
|
$(Device/dsa-migration)
|
|
$(Device/seama)
|
|
BLOCKSIZE := 64k
|
|
SEAMA_SIGNATURE := wrgac13_dlink.2013gui_dir860lb
|
|
LOADER_TYPE := bin
|
|
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | relocate-kernel | \
|
|
lzma -a0 | uImage lzma
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DIR-860L
|
|
DEVICE_VARIANT := B1
|
|
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += dir-860l-b1
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-860l-b1
|
|
|
|
define Device/dlink_dir-867-a1
|
|
$(Device/dlink_dir-8xx-a1)
|
|
DEVICE_MODEL := DIR-867
|
|
DEVICE_VARIANT := A1
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-867-a1
|
|
|
|
define Device/dlink_dir-878-a1
|
|
$(Device/dlink_dir-8xx-a1)
|
|
DEVICE_MODEL := DIR-878
|
|
DEVICE_VARIANT := A1
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-878-a1
|
|
|
|
define Device/dlink_dir-882-a1
|
|
$(Device/dlink_dir-8xx-a1)
|
|
DEVICE_MODEL := DIR-882
|
|
DEVICE_VARIANT := A1
|
|
DEVICE_PACKAGES += kmod-usb3 kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-882-a1
|
|
|
|
define Device/dlink_dir-882-r1
|
|
$(Device/dlink_dir-8xx-r1)
|
|
DEVICE_MODEL := DIR-882
|
|
DEVICE_VARIANT := R1
|
|
DEVICE_PACKAGES += kmod-usb3 kmod-usb-ledtrig-usbport
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | check-size | \
|
|
sign-dlink-ru 57c5375741c30ca9ebcb36713db4ba51 \
|
|
ab0dff19af8842cdb70a86b4b68d23f7
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-882-r1
|
|
|
|
define Device/d-team_newifi-d2
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := Newifi
|
|
DEVICE_MODEL := D2
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += d-team_newifi-d2
|
|
|
|
define Device/d-team_pbr-m1
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := PandoraBox
|
|
DEVICE_MODEL := PBR-M1
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-mt7603 kmod-mt76x2 kmod-sdhci-mt7620 \
|
|
kmod-usb3 kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += pbr-m1
|
|
endef
|
|
TARGET_DEVICES += d-team_pbr-m1
|
|
|
|
define Device/edimax_ra21s
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Edimax
|
|
DEVICE_MODEL := RA21S
|
|
DEVICE_ALT0_VENDOR := Edimax
|
|
DEVICE_ALT0_MODEL := Gemini RA21S
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
|
elx-header 02020040 8844A2D168B45A2D
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += edimax_ra21s
|
|
|
|
define Device/edimax_re23s
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 15680k
|
|
DEVICE_VENDOR := Edimax
|
|
DEVICE_MODEL := RE23S
|
|
DEVICE_ALT0_VENDOR := Edimax
|
|
DEVICE_ALT0_MODEL := Gemini RE23S
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | \
|
|
edimax-header -s CSYS -m RN76 -f 0x70000 -S 0x01100000 | pad-rootfs | \
|
|
append-metadata | check-size
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | \
|
|
edimax-header -s CSYS -m RN76 -f 0x70000 -S 0x01100000 | pad-rootfs | \
|
|
check-size
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += edimax_re23s
|
|
|
|
define Device/edimax_rg21s
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Edimax
|
|
DEVICE_MODEL := Gemini AC2600 RG21S
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
|
elx-header 02020038 8844A2D168B45A2D
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += edimax_rg21s
|
|
|
|
define Device/elecom_wrc-1167ghbk2-s
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 15488k
|
|
DEVICE_VENDOR := ELECOM
|
|
DEVICE_MODEL := WRC-1167GHBK2-S
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
|
elecom-wrc-gs-factory WRC-1167GHBK2-S 0.00
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-1167ghbk2-s
|
|
|
|
define Device/elecom_wrc-gs
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := ELECOM
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
|
elecom-wrc-gs-factory $$$$(ELECOM_HWNAME) 0.00 -N | \
|
|
append-string MT7621_ELECOM_$$$$(ELECOM_HWNAME)
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
|
|
define Device/elecom_wrc-1167gs2-b
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 11264k
|
|
DEVICE_MODEL := WRC-1167GS2-B
|
|
ELECOM_HWNAME := WRC-1167GS2
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-1167gs2-b
|
|
|
|
define Device/elecom_wrc-1167gst2
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 24576k
|
|
DEVICE_MODEL := WRC-1167GST2
|
|
ELECOM_HWNAME := WRC-1167GST2
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-1167gst2
|
|
|
|
define Device/elecom_wrc-1750gs
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 11264k
|
|
DEVICE_MODEL := WRC-1750GS
|
|
ELECOM_HWNAME := WRC-1750GS
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-1750gs
|
|
|
|
define Device/elecom_wrc-1750gst2
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 24576k
|
|
DEVICE_MODEL := WRC-1750GST2
|
|
ELECOM_HWNAME := WRC-1750GST2
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-1750gst2
|
|
|
|
define Device/elecom_wrc-1750gsv
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 11264k
|
|
DEVICE_MODEL := WRC-1750GSV
|
|
ELECOM_HWNAME := WRC-1750GSV
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-1750gsv
|
|
|
|
define Device/elecom_wrc-1900gst
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 11264k
|
|
DEVICE_MODEL := WRC-1900GST
|
|
ELECOM_HWNAME := WRC-1900GST
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-1900gst
|
|
|
|
define Device/elecom_wrc-2533ghbk-i
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := ELECOM
|
|
DEVICE_MODEL := WRC-2533GHBK-I
|
|
IMAGE_SIZE := 9856k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
|
elx-header 0107002d 8844A2D168B45A2D | \
|
|
elecom-product-header WRC-2533GHBK-I
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-2533ghbk-i
|
|
|
|
define Device/elecom_wrc-2533gst
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 11264k
|
|
DEVICE_MODEL := WRC-2533GST
|
|
ELECOM_HWNAME := WRC-2533GST
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-2533gst
|
|
|
|
define Device/elecom_wrc-2533gst2
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 24576k
|
|
DEVICE_MODEL := WRC-2533GST2
|
|
ELECOM_HWNAME := WRC-2533GST2
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-2533gst2
|
|
|
|
define Device/firefly_firewrt
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Firefly
|
|
DEVICE_MODEL := FireWRT
|
|
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += firewrt
|
|
endef
|
|
TARGET_DEVICES += firefly_firewrt
|
|
|
|
define Device/gehua_ghl-r-001
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := GeHua
|
|
DEVICE_MODEL := GHL-R-001
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += gehua_ghl-r-001
|
|
|
|
define Device/glinet_gl-mt1300
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-MT1300
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-mt1300
|
|
|
|
define Device/gnubee_gb-pc1
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := GnuBee
|
|
DEVICE_MODEL := Personal Cloud One
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-usb3 kmod-sdhci-mt7620 -wpad-openssl
|
|
IMAGE_SIZE := 32448k
|
|
endef
|
|
TARGET_DEVICES += gnubee_gb-pc1
|
|
|
|
define Device/gnubee_gb-pc2
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := GnuBee
|
|
DEVICE_MODEL := Personal Cloud Two
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-usb3 kmod-sdhci-mt7620 -wpad-openssl
|
|
IMAGE_SIZE := 32448k
|
|
endef
|
|
TARGET_DEVICES += gnubee_gb-pc2
|
|
|
|
define Device/h3c_tx180x
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 8192k
|
|
IMAGE_SIZE := 120832k
|
|
UBINIZE_OPTS := -E 5
|
|
KERNEL_LOADADDR := 0x82000000
|
|
KERNEL_INITRAMFS := kernel-bin | relocate-kernel 0x80001000 | lzma | \
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
KERNEL := $$(KERNEL_INITRAMFS) | h3c-blank-header
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
DEVICE_VENDOR := H3C
|
|
DEVICE_PACKAGES := kmod-mt7915e uboot-envtools
|
|
endef
|
|
|
|
define Device/h3c_tx1800-plus
|
|
$(Device/h3c_tx180x)
|
|
DEVICE_MODEL := TX1800 Plus
|
|
endef
|
|
TARGET_DEVICES += h3c_tx1800-plus
|
|
|
|
define Device/h3c_tx1801-plus
|
|
$(Device/h3c_tx180x)
|
|
DEVICE_MODEL := TX1801 Plus
|
|
endef
|
|
TARGET_DEVICES += h3c_tx1801-plus
|
|
|
|
define Device/h3c_tx1806
|
|
$(Device/h3c_tx180x)
|
|
DEVICE_MODEL := TX1806
|
|
endef
|
|
TARGET_DEVICES += h3c_tx1806
|
|
|
|
define Device/hiwifi_hc5962
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGE_SIZE := 32768k
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
DEVICE_VENDOR := HiWiFi
|
|
DEVICE_MODEL := HC5962
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += hiwifi_hc5962
|
|
|
|
define Device/iodata_wn-ax1167gr
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 15552k
|
|
KERNEL_INITRAMFS := $$(KERNEL) | \
|
|
iodata-factory 7864320 4 0x1055 $(KDIR)/tmp/$$(KERNEL_INITRAMFS_PREFIX)-factory.bin
|
|
DEVICE_VENDOR := I-O DATA
|
|
DEVICE_MODEL := WN-AX1167GR
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-ax1167gr
|
|
|
|
define Device/iodata_nand
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := I-O DATA
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
UBINIZE_OPTS := -E 5
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 51200k
|
|
LOADER_TYPE := bin
|
|
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | lzma | uImage lzma
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
|
|
# The OEM webinterface expects an kernel with initramfs which has the uImage
|
|
# header field ih_name.
|
|
# We don't want to set the header name field for the kernel include in the
|
|
# sysupgrade image as well, as this image shouldn't be accepted by the OEM
|
|
# webinterface. It will soft-brick the board.
|
|
|
|
define Device/iodata_wn-ax1167gr2
|
|
$(Device/iodata_nand)
|
|
DEVICE_MODEL := WN-AX1167GR2
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
|
|
uImage lzma -M 0x434f4d42 -n '3.10(XBC.1)b10' | iodata-mstc-header
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-ax1167gr2
|
|
|
|
define Device/iodata_wn-ax2033gr
|
|
$(Device/iodata_nand)
|
|
DEVICE_MODEL := WN-AX2033GR
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
|
|
uImage lzma -M 0x434f4d42 -n '3.10(VST.1)C10' | iodata-mstc-header
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-ax2033gr
|
|
|
|
define Device/iodata_wn-dx1167r
|
|
$(Device/iodata_nand)
|
|
DEVICE_MODEL := WN-DX1167R
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
|
|
uImage lzma -M 0x434f4d43 -n '3.10(XIK.1)b10' | iodata-mstc-header
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-dx1167r
|
|
|
|
define Device/iodata_wn-dx1200gr
|
|
$(Device/iodata_nand)
|
|
DEVICE_MODEL := WN-DX1200GR
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
|
|
uImage lzma -M 0x434f4d43 -n '3.10(XIQ.0)b20' | iodata-mstc-header
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-dx1200gr
|
|
|
|
define Device/iodata_wn-gx300gr
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 7616k
|
|
DEVICE_VENDOR := I-O DATA
|
|
DEVICE_MODEL := WN-GX300GR
|
|
DEVICE_PACKAGES := kmod-mt7603
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-gx300gr
|
|
|
|
define Device/iodata_wnpr2600g
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := I-O DATA
|
|
DEVICE_MODEL := WNPR2600G
|
|
IMAGE_SIZE := 13952k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
|
elx-header 0104003a 8844A2D168B45A2D
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += iodata_wnpr2600g
|
|
|
|
define Device/iptime_a6ns-m
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16128k
|
|
UIMAGE_NAME := a6nm
|
|
DEVICE_VENDOR := ipTIME
|
|
DEVICE_MODEL := A6ns-M
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += iptime_a6ns-m
|
|
|
|
define Device/iptime_a8004t
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16128k
|
|
UIMAGE_NAME := a8004t
|
|
DEVICE_VENDOR := ipTIME
|
|
DEVICE_MODEL := A8004T
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += iptime_a8004t
|
|
|
|
define Device/jcg_jhr-ac876m
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | jcg-header 89.1
|
|
JCG_MAXSIZE := 16064k
|
|
DEVICE_VENDOR := JCG
|
|
DEVICE_MODEL := JHR-AC876M
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += jcg_jhr-ac876m
|
|
|
|
define Device/jcg_q20
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
UBINIZE_OPTS := -E 5
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 91136k
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
DEVICE_VENDOR := JCG
|
|
DEVICE_MODEL := Q20
|
|
DEVICE_PACKAGES := kmod-mt7915e uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += jcg_q20
|
|
|
|
define Device/jcg_y2
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | jcg-header 95.1
|
|
JCG_MAXSIZE := 16064k
|
|
DEVICE_VENDOR := JCG
|
|
DEVICE_MODEL := Y2
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += jcg_y2
|
|
|
|
define Device/jdcloud_re-sp-01b
|
|
IMAGE_SIZE := 27328k
|
|
DEVICE_VENDOR := JDCloud
|
|
DEVICE_MODEL := RE-SP-01B
|
|
DEVICE_PACKAGES := kmod-fs-ext4 kmod-mt7603 kmod-mt7615e \
|
|
kmod-mt7615-firmware kmod-sdhci-mt7620 kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += jdcloud_re-sp-01b
|
|
|
|
define Device/lenovo_newifi-d1
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := Newifi
|
|
DEVICE_MODEL := D1
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 kmod-sdhci-mt7620 \
|
|
kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += newifi-d1
|
|
endef
|
|
TARGET_DEVICES += lenovo_newifi-d1
|
|
|
|
define Device/linksys_e5600
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 26624k
|
|
DEVICE_VENDOR := Linksys
|
|
DEVICE_MODEL := E5600
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
|
uboot-envtools
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | check-size | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
|
|
append-ubi | check-size | gemtek-trailer
|
|
endef
|
|
TARGET_DEVICES += linksys_e5600
|
|
|
|
define Device/linksys_ea7xxx
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 36864k
|
|
DEVICE_VENDOR := Linksys
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-mt7615e kmod-mt7615-firmware \
|
|
uboot-envtools
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGES := sysupgrade.bin factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata | check-size
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
|
|
append-ubi | check-size | linksys-image type=$$$$(LINKSYS_HWNAME)
|
|
endef
|
|
|
|
define Device/linksys_ea7300-v1
|
|
$(Device/linksys_ea7xxx)
|
|
DEVICE_MODEL := EA7300
|
|
DEVICE_VARIANT := v1
|
|
LINKSYS_HWNAME := EA7300
|
|
endef
|
|
TARGET_DEVICES += linksys_ea7300-v1
|
|
|
|
define Device/linksys_ea7300-v2
|
|
$(Device/linksys_ea7xxx)
|
|
DEVICE_MODEL := EA7300
|
|
DEVICE_VARIANT := v2
|
|
LINKSYS_HWNAME := EA7300v2
|
|
DEVICE_PACKAGES += kmod-mt7603
|
|
endef
|
|
TARGET_DEVICES += linksys_ea7300-v2
|
|
|
|
define Device/linksys_ea7500-v2
|
|
$(Device/linksys_ea7xxx)
|
|
DEVICE_MODEL := EA7500
|
|
DEVICE_VARIANT := v2
|
|
LINKSYS_HWNAME := EA7500v2
|
|
endef
|
|
TARGET_DEVICES += linksys_ea7500-v2
|
|
|
|
define Device/linksys_ea8100-v1
|
|
$(Device/linksys_ea7xxx)
|
|
DEVICE_MODEL := EA8100
|
|
DEVICE_VARIANT := v1
|
|
LINKSYS_HWNAME := EA8100
|
|
endef
|
|
TARGET_DEVICES += linksys_ea8100-v1
|
|
|
|
define Device/linksys_re6500
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 7872k
|
|
DEVICE_VENDOR := Linksys
|
|
DEVICE_MODEL := RE6500
|
|
DEVICE_PACKAGES := kmod-mt76x2
|
|
SUPPORTED_DEVICES += re6500
|
|
endef
|
|
TARGET_DEVICES += linksys_re6500
|
|
|
|
define Device/mediatek_ap-mt7621a-v60
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 7872k
|
|
DEVICE_VENDOR := Mediatek
|
|
DEVICE_MODEL := AP-MT7621A-V60 EVB
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-sdhci-mt7620 kmod-sound-mt7620 -wpad-openssl
|
|
endef
|
|
TARGET_DEVICES += mediatek_ap-mt7621a-v60
|
|
|
|
define Device/mediatek_mt7621-eval-board
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 64k
|
|
IMAGE_SIZE := 15104k
|
|
DEVICE_VENDOR := MediaTek
|
|
DEVICE_MODEL := MT7621 EVB
|
|
DEVICE_PACKAGES := -wpad-openssl
|
|
SUPPORTED_DEVICES += mt7621
|
|
endef
|
|
TARGET_DEVICES += mediatek_mt7621-eval-board
|
|
|
|
define Device/MikroTik
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := MikroTik
|
|
BLOCKSIZE := 64k
|
|
IMAGE_SIZE := 16128k
|
|
DEVICE_PACKAGES := kmod-usb3
|
|
KERNEL_NAME := vmlinuz
|
|
KERNEL := kernel-bin | append-dtb-elf
|
|
IMAGE/sysupgrade.bin := append-kernel | kernel2minor -s 1024 | \
|
|
pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | append-metadata | \
|
|
check-size
|
|
endef
|
|
|
|
define Device/mikrotik_routerboard-750gr3
|
|
$(Device/MikroTik)
|
|
DEVICE_MODEL := RouterBOARD 750Gr3
|
|
DEVICE_PACKAGES += -wpad-openssl
|
|
SUPPORTED_DEVICES += mikrotik,rb750gr3
|
|
endef
|
|
TARGET_DEVICES += mikrotik_routerboard-750gr3
|
|
|
|
define Device/mikrotik_routerboard-760igs
|
|
$(Device/MikroTik)
|
|
DEVICE_MODEL := RouterBOARD 760iGS
|
|
DEVICE_PACKAGES += kmod-sfp -wpad-openssl
|
|
endef
|
|
TARGET_DEVICES += mikrotik_routerboard-760igs
|
|
|
|
define Device/mikrotik_routerboard-m11g
|
|
$(Device/MikroTik)
|
|
DEVICE_MODEL := RouterBOARD M11G
|
|
DEVICE_PACKAGES := -wpad-openssl
|
|
SUPPORTED_DEVICES += mikrotik,rbm11g
|
|
endef
|
|
TARGET_DEVICES += mikrotik_routerboard-m11g
|
|
|
|
define Device/mikrotik_routerboard-m33g
|
|
$(Device/MikroTik)
|
|
DEVICE_MODEL := RouterBOARD M33G
|
|
DEVICE_PACKAGES := -wpad-openssl
|
|
SUPPORTED_DEVICES += mikrotik,rbm33g
|
|
endef
|
|
TARGET_DEVICES += mikrotik_routerboard-m33g
|
|
|
|
define Device/mqmaker_witi
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := MQmaker
|
|
DEVICE_MODEL := WiTi
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-mt76x2 kmod-sdhci-mt7620 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += witi mqmaker,witi-256m mqmaker,witi-512m
|
|
endef
|
|
TARGET_DEVICES += mqmaker_witi
|
|
|
|
define Device/mtc_wr1201
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16000k
|
|
DEVICE_VENDOR := MTC
|
|
DEVICE_MODEL := Wireless Router WR1201
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | uImage lzma -n 'WR1201_8_128'
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += mtc_wr1201
|
|
|
|
define Device/netgear_ex6150
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := NETGEAR
|
|
DEVICE_MODEL := EX6150
|
|
DEVICE_PACKAGES := kmod-mt76x2
|
|
NETGEAR_BOARD_ID := U12H318T00_NETGEAR
|
|
IMAGE_SIZE := 14848k
|
|
IMAGES += factory.chk
|
|
IMAGE/factory.chk := $$(sysupgrade_bin) | check-size | netgear-chk
|
|
endef
|
|
TARGET_DEVICES += netgear_ex6150
|
|
|
|
define Device/netgear_sercomm_nand
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGES += factory.img kernel.bin rootfs.bin
|
|
IMAGE/factory.img := pad-extra 2048k | append-kernel | pad-to 6144k | \
|
|
append-ubi | pad-to $$$$(BLOCKSIZE) | sercom-footer | pad-to 128 | \
|
|
zip $$$$(SERCOMM_HWNAME).bin | sercom-seal
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/kernel.bin := append-kernel
|
|
IMAGE/rootfs.bin := append-ubi | check-size
|
|
DEVICE_VENDOR := NETGEAR
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-usb3 kmod-usb-ledtrig-usbport
|
|
endef
|
|
|
|
define Device/netgear_r6220
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R6220
|
|
SERCOMM_HWNAME := R6220
|
|
SERCOMM_HWID := AYA
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x0086
|
|
IMAGE_SIZE := 28672k
|
|
DEVICE_PACKAGES += kmod-mt76x2
|
|
SUPPORTED_DEVICES += r6220
|
|
endef
|
|
TARGET_DEVICES += netgear_r6220
|
|
|
|
|
|
define Device/netgear_r6260
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R6260
|
|
SERCOMM_HWNAME := R6260
|
|
SERCOMM_HWID := CHJ
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x0052
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_r6260
|
|
|
|
define Device/netgear_r6350
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R6350
|
|
SERCOMM_HWNAME := R6350
|
|
SERCOMM_HWID := CHJ
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x0052
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_r6350
|
|
|
|
define Device/netgear_r6700-v2
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R6700
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_ALT0_VENDOR := NETGEAR
|
|
DEVICE_ALT0_MODEL := Nighthawk AC2400
|
|
DEVICE_ALT0_VARIANT := v1
|
|
SERCOMM_HWNAME := R6950
|
|
SERCOMM_HWID := BZV
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x1032
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_r6700-v2
|
|
|
|
define Device/netgear_r6800
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R6800
|
|
SERCOMM_HWNAME := R6950
|
|
SERCOMM_HWID := BZV
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x0062
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_r6800
|
|
|
|
define Device/netgear_r6850
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R6850
|
|
SERCOMM_HWNAME := R6850
|
|
SERCOMM_HWID := CHJ
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x0052
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_r6850
|
|
|
|
define Device/netgear_r6900-v2
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R6900
|
|
DEVICE_VARIANT := v2
|
|
SERCOMM_HWNAME := R6950
|
|
SERCOMM_HWID := BZV
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x1032
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_r6900-v2
|
|
|
|
define Device/netgear_r7200
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R7200
|
|
SERCOMM_HWNAME := R6950
|
|
SERCOMM_HWID := BZV
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x1032
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_r7200
|
|
|
|
define Device/netgear_wac104
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := WAC104
|
|
SERCOMM_HWNAME := WAC104
|
|
SERCOMM_HWID := CAY
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x0006
|
|
IMAGE_SIZE := 28672k
|
|
DEVICE_PACKAGES += kmod-mt76x2
|
|
endef
|
|
TARGET_DEVICES += netgear_wac104
|
|
|
|
define Device/netgear_wac124
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := WAC124
|
|
SERCOMM_HWNAME := WAC124
|
|
SERCOMM_HWID := CTL
|
|
SERCOMM_HWVER := A003
|
|
SERCOMM_SWVER := 0x0402
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_wac124
|
|
|
|
define Device/netgear_wndr3700-v5
|
|
$(Device/dsa-migration)
|
|
$(Device/netgear_sercomm_nor)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 15232k
|
|
DEVICE_MODEL := WNDR3700
|
|
DEVICE_VARIANT := v5
|
|
SERCOMM_HWNAME := WNDR3700v5
|
|
SERCOMM_HWID := AYB
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x1054
|
|
SERCOMM_PAD := 320k
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += wndr3700v5
|
|
endef
|
|
TARGET_DEVICES += netgear_wndr3700-v5
|
|
|
|
define Device/netis_wf2881
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
FILESYSTEMS := squashfs
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 129280k
|
|
UBINIZE_OPTS := -E 5
|
|
UIMAGE_NAME := WF2881_0.0.00
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | netis-tail WF2881 | uImage lzma
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
DEVICE_VENDOR := NETIS
|
|
DEVICE_MODEL := WF2881
|
|
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += netis_wf2881
|
|
|
|
define Device/phicomm_k2p
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 15744k
|
|
DEVICE_VENDOR := Phicomm
|
|
DEVICE_MODEL := K2P
|
|
DEVICE_ALT0_VENDOR := Phicomm
|
|
DEVICE_ALT0_MODEL := KE 2P
|
|
SUPPORTED_DEVICES += k2p
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += phicomm_k2p
|
|
|
|
define Device/planex_vr500
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 65216k
|
|
DEVICE_VENDOR := Planex
|
|
DEVICE_MODEL := VR500
|
|
DEVICE_PACKAGES := kmod-usb3 -wpad-openssl
|
|
SUPPORTED_DEVICES += vr500
|
|
endef
|
|
TARGET_DEVICES += planex_vr500
|
|
|
|
define Device/raisecom_msg1500-x-00
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 129280k
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
DEVICE_VENDOR := RAISECOM
|
|
DEVICE_MODEL := MSG1500
|
|
DEVICE_VARIANT := X.00
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += raisecom_msg1500-x-00
|
|
|
|
define Device/samknows_whitebox-v8
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := SamKnows
|
|
DEVICE_MODEL := Whitebox 8
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport uboot-envtools
|
|
SUPPORTED_DEVICES += sk-wb8
|
|
endef
|
|
TARGET_DEVICES += samknows_whitebox-v8
|
|
|
|
define Device/sercomm_na502
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
IMAGE_SIZE := 20480k
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
UBINIZE_OPTS := -E 5
|
|
KERNEL_SIZE := 4096k
|
|
DEVICE_VENDOR := SERCOMM
|
|
DEVICE_MODEL := NA502
|
|
DEVICE_PACKAGES := kmod-mt76x2 kmod-mt7603 kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += sercomm_na502
|
|
|
|
define Device/storylink_sap-g3200u3
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 7872k
|
|
DEVICE_VENDOR := STORYLiNK
|
|
DEVICE_MODEL := SAP-G3200U3
|
|
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += sap-g3200u3
|
|
endef
|
|
TARGET_DEVICES += storylink_sap-g3200u3
|
|
|
|
define Device/telco-electronics_x1
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Telco Electronics
|
|
DEVICE_MODEL := X1
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-mt76
|
|
endef
|
|
TARGET_DEVICES += telco-electronics_x1
|
|
|
|
define Device/thunder_timecloud
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Thunder
|
|
DEVICE_MODEL := Timecloud
|
|
DEVICE_PACKAGES := kmod-usb3 -wpad-openssl
|
|
SUPPORTED_DEVICES += timecloud
|
|
endef
|
|
TARGET_DEVICES += thunder_timecloud
|
|
|
|
define Device/totolink_a7000r
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
UIMAGE_NAME := C8340R1C-9999
|
|
DEVICE_VENDOR := TOTOLINK
|
|
DEVICE_MODEL := A7000R
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += totolink_a7000r
|
|
|
|
define Device/totolink_x5000r
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
UIMAGE_NAME := C8343R-9999
|
|
DEVICE_VENDOR := TOTOLINK
|
|
DEVICE_MODEL := X5000R
|
|
DEVICE_PACKAGES := kmod-mt7915e
|
|
endef
|
|
TARGET_DEVICES += totolink_x5000r
|
|
|
|
define Device/tplink_archer-a6-v3
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := Archer A6
|
|
DEVICE_VARIANT := V3
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e \
|
|
kmod-mt7663-firmware-ap
|
|
TPLINK_BOARD_ID := ARCHER-A6-V3
|
|
KERNEL := $(KERNEL_DTB) | uImage lzma
|
|
IMAGE_SIZE := 15744k
|
|
endef
|
|
TARGET_DEVICES += tplink_archer-a6-v3
|
|
|
|
define Device/tplink_archer-c6u-v1
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := Archer C6U
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-mt7603 \
|
|
kmod-mt7615e kmod-mt7663-firmware-ap \
|
|
kmod-usb3 kmod-usb-ledtrig-usbport
|
|
KERNEL := $(KERNEL_DTB) | uImage lzma
|
|
TPLINK_BOARD_ID := ARCHER-C6U-V1
|
|
IMAGE_SIZE := 15744k
|
|
endef
|
|
TARGET_DEVICES += tplink_archer-c6u-v1
|
|
|
|
define Device/tplink_eap235-wall-v1
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := EAP235-Wall
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap
|
|
TPLINK_BOARD_ID := EAP235-WALL-V1
|
|
IMAGE_SIZE := 13440k
|
|
IMAGE/factory.bin := append-rootfs | tplink-safeloader factory | \
|
|
pad-extra 128
|
|
endef
|
|
TARGET_DEVICES += tplink_eap235-wall-v1
|
|
|
|
define Device/tplink_re350-v1
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := RE350
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
|
|
TPLINK_BOARD_ID := RE350-V1
|
|
IMAGE_SIZE := 6016k
|
|
SUPPORTED_DEVICES += re350-v1
|
|
endef
|
|
TARGET_DEVICES += tplink_re350-v1
|
|
|
|
define Device/tplink_re500-v1
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := RE500
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
TPLINK_BOARD_ID := RE500-V1
|
|
IMAGE_SIZE := 14208k
|
|
endef
|
|
TARGET_DEVICES += tplink_re500-v1
|
|
|
|
define Device/tplink_re650-v1
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := RE650
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
|
|
TPLINK_BOARD_ID := RE650-V1
|
|
IMAGE_SIZE := 14208k
|
|
endef
|
|
TARGET_DEVICES += tplink_re650-v1
|
|
|
|
define Device/ubnt_edgerouter_common
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := Ubiquiti
|
|
IMAGE_SIZE := 256768k
|
|
FILESYSTEMS := squashfs
|
|
KERNEL_SIZE := 3145728
|
|
KERNEL_INITRAMFS := $$(KERNEL) | \
|
|
ubnt-erx-factory-image $(KDIR)/tmp/$$(KERNEL_INITRAMFS_PREFIX)-factory.tar
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
DEVICE_PACKAGES += -wpad-openssl
|
|
endef
|
|
|
|
define Device/ubnt_edgerouter-x
|
|
$(Device/ubnt_edgerouter_common)
|
|
DEVICE_MODEL := EdgeRouter X
|
|
SUPPORTED_DEVICES += ubnt-erx ubiquiti,edgerouterx
|
|
endef
|
|
TARGET_DEVICES += ubnt_edgerouter-x
|
|
|
|
define Device/ubnt_edgerouter-x-sfp
|
|
$(Device/ubnt_edgerouter_common)
|
|
DEVICE_MODEL := EdgeRouter X SFP
|
|
DEVICE_PACKAGES += kmod-i2c-algo-pca kmod-gpio-pca953x kmod-sfp
|
|
SUPPORTED_DEVICES += ubnt-erx-sfp ubiquiti,edgerouterx-sfp
|
|
endef
|
|
TARGET_DEVICES += ubnt_edgerouter-x-sfp
|
|
|
|
define Device/ubnt_unifi-6-lite
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := Ubiquiti
|
|
DEVICE_MODEL := UniFi 6 Lite
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7915e
|
|
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
IMAGE_SIZE := 15424k
|
|
endef
|
|
TARGET_DEVICES += ubnt_unifi-6-lite
|
|
|
|
define Device/ubnt_unifi-nanohd
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := Ubiquiti
|
|
DEVICE_MODEL := UniFi nanoHD
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware
|
|
IMAGE_SIZE := 15552k
|
|
endef
|
|
TARGET_DEVICES += ubnt_unifi-nanohd
|
|
|
|
define Device/unielec_u7621-01-16m
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := UniElec
|
|
DEVICE_MODEL := U7621-01
|
|
DEVICE_VARIANT := 16M
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += unielec_u7621-01-16m
|
|
|
|
define Device/unielec_u7621-06-16m
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := UniElec
|
|
DEVICE_MODEL := U7621-06
|
|
DEVICE_VARIANT := 16M
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-usb3 -wpad-openssl
|
|
SUPPORTED_DEVICES += u7621-06-256M-16M unielec,u7621-06-256m-16m
|
|
endef
|
|
TARGET_DEVICES += unielec_u7621-06-16m
|
|
|
|
define Device/unielec_u7621-06-64m
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 65216k
|
|
DEVICE_VENDOR := UniElec
|
|
DEVICE_MODEL := U7621-06
|
|
DEVICE_VARIANT := 64M
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-usb3 -wpad-openssl
|
|
SUPPORTED_DEVICES += unielec,u7621-06-512m-64m
|
|
endef
|
|
TARGET_DEVICES += unielec_u7621-06-64m
|
|
|
|
define Device/wavlink_wl-wn531a6
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := Wavlink
|
|
DEVICE_MODEL := WL-WN531A6
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware kmod-usb3
|
|
IMAGE_SIZE := 15040k
|
|
endef
|
|
TARGET_DEVICES += wavlink_wl-wn531a6
|
|
|
|
define Device/wevo_11acnas
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
UIMAGE_NAME := 11AC-NAS-Router(0.0.0)
|
|
DEVICE_VENDOR := WeVO
|
|
DEVICE_MODEL := 11AC NAS Router
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += 11acnas
|
|
endef
|
|
TARGET_DEVICES += wevo_11acnas
|
|
|
|
define Device/wevo_w2914ns-v2
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
UIMAGE_NAME := W2914NS-V2(0.0.0)
|
|
DEVICE_VENDOR := WeVO
|
|
DEVICE_MODEL := W2914NS
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += w2914nsv2
|
|
endef
|
|
TARGET_DEVICES += wevo_w2914ns-v2
|
|
|
|
define Device/winstars_ws-wn583a6
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 7872k
|
|
DEVICE_VENDOR := Winstars
|
|
DEVICE_MODEL := WS-WN583A6
|
|
DEVICE_ALT0_VENDOR := Gemeita
|
|
DEVICE_ALT0_MODEL := AC2100
|
|
KERNEL_INITRAMFS_SUFFIX := -WN583A6$$(KERNEL_SUFFIX)
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += winstars_ws-wn583a6
|
|
|
|
define Device/xiaomi_nand_separate
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := Xiaomi
|
|
DEVICE_PACKAGES := uboot-envtools
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGES += kernel1.bin rootfs0.bin
|
|
IMAGE/kernel1.bin := append-kernel
|
|
IMAGE/rootfs0.bin := append-ubi | check-size
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
|
|
define Device/xiaomi_mi-router-3g
|
|
$(Device/xiaomi_nand_separate)
|
|
DEVICE_MODEL := Mi Router 3G
|
|
IMAGE_SIZE := 124416k
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += R3G mir3g xiaomi,mir3g
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-3g
|
|
|
|
define Device/xiaomi_mi-router-3g-v2
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 14848k
|
|
DEVICE_VENDOR := Xiaomi
|
|
DEVICE_MODEL := Mi Router 3G
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
|
|
SUPPORTED_DEVICES += xiaomi,mir3g-v2
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-3g-v2
|
|
|
|
define Device/xiaomi_mi-router-3-pro
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE:= 4096k
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGE_SIZE := 255488k
|
|
DEVICE_VENDOR := Xiaomi
|
|
DEVICE_MODEL := Mi Router 3 Pro
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport uboot-envtools
|
|
SUPPORTED_DEVICES += xiaomi,mir3p
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-3-pro
|
|
|
|
define Device/xiaomi_mi-router-4
|
|
$(Device/xiaomi_nand_separate)
|
|
DEVICE_MODEL := Mi Router 4
|
|
IMAGE_SIZE := 124416k
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt76x2
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-4
|
|
|
|
define Device/xiaomi_mi-router-4a-gigabit
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 14848k
|
|
DEVICE_VENDOR := Xiaomi
|
|
DEVICE_MODEL := Mi Router 4A
|
|
DEVICE_VARIANT := Gigabit Edition
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-4a-gigabit
|
|
|
|
define Device/xiaomi_mi-router-4a-gigabit-v2
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 14784k
|
|
DEVICE_VENDOR := Xiaomi
|
|
DEVICE_MODEL := Mi Router 4A
|
|
DEVICE_VARIANT := Gigabit Edition v2
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-4a-gigabit-v2
|
|
|
|
define Device/xiaomi_mi-router-ac2100
|
|
$(Device/xiaomi_nand_separate)
|
|
DEVICE_MODEL := Mi Router AC2100
|
|
IMAGE_SIZE := 120320k
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-ac2100
|
|
|
|
define Device/xiaomi_mi-router-cr660x
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := Xiaomi
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGE_SIZE := 128512k
|
|
IMAGES += firmware.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/firmware.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
DEVICE_PACKAGES += kmod-mt7915e uboot-envtools
|
|
endef
|
|
|
|
define Device/xiaomi_mi-router-cr6606
|
|
$(Device/xiaomi_mi-router-cr660x)
|
|
DEVICE_MODEL := Mi Router CR6606
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-cr6606
|
|
|
|
define Device/xiaomi_mi-router-cr6608
|
|
$(Device/xiaomi_mi-router-cr660x)
|
|
DEVICE_MODEL := Mi Router CR6608
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-cr6608
|
|
|
|
define Device/xiaomi_mi-router-cr6609
|
|
$(Device/xiaomi_mi-router-cr660x)
|
|
DEVICE_MODEL := Mi Router CR6609
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-cr6609
|
|
|
|
define Device/xiaomi_redmi-router-ac2100
|
|
$(Device/xiaomi_nand_separate)
|
|
DEVICE_MODEL := Redmi Router AC2100
|
|
IMAGE_SIZE := 120320k
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += xiaomi_redmi-router-ac2100
|
|
|
|
define Device/xiaoyu_xy-c5
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := XiaoYu
|
|
DEVICE_MODEL := XY-C5
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-usb3 -wpad-openssl
|
|
endef
|
|
TARGET_DEVICES += xiaoyu_xy-c5
|
|
|
|
define Device/xzwifi_creativebox-v1
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := CreativeBox
|
|
DEVICE_MODEL := v1
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-mt7603 kmod-mt76x2 kmod-sdhci-mt7620 \
|
|
kmod-usb3 -wpad-openssl
|
|
endef
|
|
TARGET_DEVICES += xzwifi_creativebox-v1
|
|
|
|
define Device/youhua_wr1200js
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := YouHua
|
|
DEVICE_MODEL := WR1200JS
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += youhua_wr1200js
|
|
|
|
define Device/youku_yk-l2
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Youku
|
|
DEVICE_MODEL := YK-L2
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-sdhci-mt7620 \
|
|
kmod-usb3 kmod-usb-ledtrig-usbport
|
|
UIMAGE_MAGIC := 0x12291000
|
|
UIMAGE_NAME := 400000000000000000003000
|
|
endef
|
|
TARGET_DEVICES += youku_yk-l2
|
|
|
|
define Device/yuncore_ax820
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 15808k
|
|
DEVICE_VENDOR := YunCore
|
|
DEVICE_MODEL := AX820
|
|
DEVICE_PACKAGES := kmod-mt7915e
|
|
endef
|
|
TARGET_DEVICES += yuncore_ax820
|
|
|
|
define Device/zbtlink_zbt-we1326
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Zbtlink
|
|
DEVICE_MODEL := ZBT-WE1326
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 kmod-sdhci-mt7620
|
|
SUPPORTED_DEVICES += zbt-we1326
|
|
endef
|
|
TARGET_DEVICES += zbtlink_zbt-we1326
|
|
|
|
define Device/zbtlink_zbt-we3526
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Zbtlink
|
|
DEVICE_MODEL := ZBT-WE3526
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += zbtlink_zbt-we3526
|
|
|
|
define Device/zbtlink_zbt-wg2626
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Zbtlink
|
|
DEVICE_MODEL := ZBT-WG2626
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += zbt-wg2626
|
|
endef
|
|
TARGET_DEVICES += zbtlink_zbt-wg2626
|
|
|
|
define Device/zbtlink_zbt-wg3526-16m
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Zbtlink
|
|
DEVICE_MODEL := ZBT-WG3526
|
|
DEVICE_VARIANT := 16M
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 \
|
|
kmod-usb3 kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += zbt-wg3526 zbt-wg3526-16M
|
|
endef
|
|
TARGET_DEVICES += zbtlink_zbt-wg3526-16m
|
|
|
|
define Device/zbtlink_zbt-wg3526-32m
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := Zbtlink
|
|
DEVICE_MODEL := ZBT-WG3526
|
|
DEVICE_VARIANT := 32M
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 \
|
|
kmod-usb3 kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += ac1200pro zbt-wg3526-32M
|
|
endef
|
|
TARGET_DEVICES += zbtlink_zbt-wg3526-32m
|
|
|
|
define Device/zio_freezio
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := ZIO
|
|
DEVICE_MODEL := FREEZIO
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += zio_freezio
|
|
|
|
define Device/zyxel_nr7101
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
UBINIZE_OPTS := -E 5
|
|
DEVICE_VENDOR := ZyXEL
|
|
DEVICE_MODEL := NR7101
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-usb3 uboot-envtools kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
|
|
KERNEL := $(KERNEL_DTB) | uImage lzma | zytrx-header $$(DEVICE_MODEL) $$(VERSION_DIST)-$$(REVISION)
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | uImage lzma | zytrx-header $$(DEVICE_MODEL) 9.99(ABUV.9)$$(VERSION_DIST)-recovery
|
|
KERNEL_INITRAMFS_SUFFIX := -recovery.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
TARGET_DEVICES += zyxel_nr7101
|
|
|
|
define Device/zyxel_wap6805
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := ZyXEL
|
|
DEVICE_MODEL := WAP6805
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7621-qtn-rgmii
|
|
KERNEL := $(KERNEL_DTB) | uImage lzma | uimage-padhdr 160
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
TARGET_DEVICES += zyxel_wap6805
|