An opensource OpenWrt variant for mainland China users.
d90624d341
Hardware -------- MediaTek MT7622 512MB DDR3 RAM 64M SPI-NOR Flash (Winbond W25Q512JV) MediaTek MT7622 802.11bgn 4T4R WMAC MediaTek MT7915 802.11ax 4T4R Marvell AQR1112 100/1000/2500 NBase-T PHY Holtek HT32F52241 LED controller Reset Switch UART ---- CPU UART0 at the pinout next to the Holtek MCU. Pinout (first pin next to SoC / MCU) 0 3V3 1 RX 2 TX 3 GND Settings are 115200 8N1. Opening the case ---------------- Opening the case is not a nice task, as itis glued together. Insert a flat knife between the front and back casing below the ethernet port. Open up a gap this way and insert a flat scredriver, remove the knife. Work your way around the casing by applying force to seperate the front and back casing. This losens the glue and opens the plastic clips. Be gentle, as these clips are very cheap and break quickly. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Transfer the OpenWrt sysupgrade image to the device using SCP. 3. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 4. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6 5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock8 $ dd if=openwrt.bin of=/dev/mtdblock9 6. Reboot the device. It should boot into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net> |
||
|---|---|---|
| config | ||
| include | ||
| LICENSES | ||
| package | ||
| scripts | ||
| target | ||
| toolchain | ||
| tools | ||
| .gitattributes | ||
| .gitignore | ||
| BSDmakefile | ||
| Config.in | ||
| CONTRIBUTED.md | ||
| COPYING | ||
| feeds.conf.default | ||
| Makefile | ||
| README.md | ||
| rules.mk | ||
PROJECT IMMORTALWRT
The Core Source Code of ImmortalWrt
Welcome to our Telegram Group: @ctcgfw_openwrt_discuss.
How to make it
Minimum requirements
Linux with case sensitive
2G DDR2 RAM
2 CPU Cores (AMD64, 1.4Ghz)
25G disk space left
Has access to both ChinaNet & Internet
Install the necessary packages (for Ubuntu user)
sudo apt-get update -y
sudo apt-get full-upgrade -y
sudo apt-get install -y build-essential asciidoc binutils bzip2 gawk gettext git libncurses5-dev libz-dev patch unzip zlib1g-dev lib32gcc1 libc6-dev-i386 subversion flex uglifyjs git-core gcc-multilib g++-multilib p7zip p7zip-full msmtp libssl-dev texinfo libreadline-dev libglib2.0-dev xmlto qemu-utils upx libelf-dev autoconf automake libtool autopoint ccache curl wget vim nano python python3 python-pip python3-pip python-ply python3-ply haveged lrzsz device-tree-compiler scons antlr3 gperf intltool rsync
For mainland China & Ubuntu(16.04+) user, you may run the following command to setup quickly:
sudo bash -c "bash <(curl -s https://build-scripts.project-openwrt.eu.org/init_build_environment.sh)"
Clone the source
git clone -b openwrt-18.06-k5.4 --single-branch https://github.com/immortalwrt/immortalwrt && cd immortalwrt
./scripts/feeds update -a && ./scripts/feeds install -a
Configure your firmware
make menuconfig
Make it
make -j$(nproc) V=s
Tips
You'd better not use root to make it, or you may be not able to use.
Default login address: 192.168.1.1, username is root and password is password.