fish/immortalwrt
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
dfc751a074
immortalwrt/target/linux/ipq40xx/image/Makefile
Leon M. George dd74723386 ipq40xx: add cpximg to flash Compex WPJ428 via bootloader 
Generate a cpximg that is compatible with the cpximg loader in Compex' u-boot.
The cpximg loader can be started either by holding the reset button during power
up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept an image
appropriate for the board revision that is etched on the board (e.g. 6A04).

The image can be pushed using tftp:
  tftp -v -m binary 192.168.1.1 -c put openwrt-ipq40xx-generic-compex_wpj428-squashfs-cpximg-6a04.bin

cpximg files can also be used with the sysupgrade utility in stock images.
(add SSH key in luci for root access)

In mkmylofw_32m, the calculation of the "partition size" has been preferred
to just padding the partition as this will result in less block transfers
during flashing (while the additional complexity is bearable).

Signed-off-by: Leon M. George <leon@georgemail.eu>
Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-11 09:00:53 +08:00

556 lines
17 KiB
Makefile
Raw Blame History

include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/image.mk
DEVICE_VARS += RAS_BOARD RAS_ROOTFS_SIZE RAS_VERSION \
WRGG_DEVNAME WRGG_SIGNATURE
define Device/Default
PROFILES := Default
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
KERNEL_INITRAMFS_PREFIX := $$(IMG_PREFIX)-$(1)-initramfs
KERNEL_PREFIX := $$(IMAGE_PREFIX)
KERNEL_LOADADDR := 0x80208000
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
IMAGE/sysupgrade.bin = sysupgrade-tar | append-metadata
IMAGE/sysupgrade.bin/squashfs :=
endef
define Device/FitImage
KERNEL_SUFFIX := -fit-uImage.itb
KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL_NAME := Image
endef
define Device/FitImageLzma
KERNEL_SUFFIX := -fit-uImage.itb
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL_NAME := Image
endef
define Device/FitzImage
KERNEL_SUFFIX := -fit-zImage.itb
KERNEL = kernel-bin | fit none $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL_NAME := zImage
endef
define Device/UbiFit
KERNEL_IN_UBI := 1
IMAGES := nand-factory.ubi nand-sysupgrade.bin
IMAGE/nand-factory.ubi := append-ubi
IMAGE/nand-sysupgrade.bin := sysupgrade-tar | append-metadata
endef
define Device/DniImage
KERNEL_SUFFIX := -fit-uImage.itb
KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL_NAME := Image
NETGEAR_BOARD_ID :=
NETGEAR_HW_ID :=
IMAGES := factory.img sysupgrade.bin
IMAGE/factory.img := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | netgear-dni
IMAGE/sysupgrade.bin := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | append-metadata
endef
DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
define Build/mkmylofw_32m
$(eval device_id=$(word 1,$(1)))
$(eval revision=$(word 2,$(1)))
let \
size="$$(stat -c%s $@)" \
pad="$(subst k,* 1024,$(BLOCKSIZE))" \
pad="(pad - (size % pad)) % pad" \
newsize='size + pad'; \
$(STAGING_DIR_HOST)/bin/mkmylofw \
-B WPE72 -i 0x11f6:$(device_id):0x11f6:$(device_id) -r $(revision) \
-s 0x2000000 -p0x180000:$$newsize:al:0x80208000:"OpenWrt":$@ \
$@.new
@mv $@.new $@
endef
define Build/SenaoFW
-$(STAGING_DIR_HOST)/bin/mksenaofw \
-n $(BOARD_NAME) -r $(VENDOR_ID) -p $(1) \
-c $(DATECODE) -w $(2) -x $(CW_VER) -t 0 \
-e $@ \
-o $@.new
@cp $@.new $@
endef
define Build/wrgg-image
mkwrggimg -i $@ \
-o $@.new \
-d "$(WRGG_DEVNAME)" \
-s "$(WRGG_SIGNATURE)" \
-v "" -m "" -B ""
mv $@.new $@
endef
define Device/8dev_jalapeno
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := 8devices
DEVICE_MODEL := Jalapeno
DEVICE_DTS := qcom-ipq4018-jalapeno
BLOCKSIZE := 128k
PAGESIZE := 2048
endef
TARGET_DEVICES += 8dev_jalapeno
define Device/alfa-network_ap120c-ac
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := ALFA Network
DEVICE_MODEL := AP120C-AC
DEVICE_DTS := qcom-ipq4018-ap120c-ac
DEVICE_PACKAGES := kmod-usb-acm \
kmod-tpm-i2c-atmel uboot-envtools
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
IMAGES := nand-factory.bin nand-sysupgrade.bin
IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
endef
TARGET_DEVICES += alfa-network_ap120c-ac
define Device/asus_map-ac2200
$(call Device/FitImageLzma)
DEVICE_VENDOR := ASUS
DEVICE_MODEL := Lyra (MAP-AC2200)
DEVICE_DTS := qcom-ipq4019-map-ac2200
IMAGES := sysupgrade.bin
DEVICE_PACKAGES := ath10k-firmware-qca9888 kmod-ath3k
endef
TARGET_DEVICES += asus_map-ac2200
define Device/asus_rt-ac58u
$(call Device/FitImageLzma)
DEVICE_VENDOR := ASUS
DEVICE_MODEL := RT-AC58U / RT-AC1300UHP
DEVICE_DTS := qcom-ipq4018-rt-ac58u
BLOCKSIZE := 128k
PAGESIZE := 2048
DTB_SIZE := 65536
IMAGE_SIZE := 20439364
FILESYSTEMS := squashfs
# Someone - in their infinite wisdom - decided to put the firmware
# version in front of the image name \03\00\00\04 => Version 3.0.0.4
# Since u-boot works with strings we either need another fixup step
# to add a version... or we are very careful not to add '\0' into that
# string and call it a day.... Yeah, we do the latter!
UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC58U')
KERNEL_INITRAMFS := $$(KERNEL) | uImage none
KERNEL_INITRAMFS_SUFFIX := -factory.trx
IMAGES := sysupgrade.bin
DEVICE_PACKAGES := -kmod-ath10k -ath10k-firmware-qca4019 \
kmod-ath10k-ct-smallbuffers ath10k-firmware-qca4019-ct kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += asus_rt-ac58u
define Device/asus_rt-acrh17
$(call Device/FitImageLzma)
DEVICE_VENDOR := ASUS
DEVICE_MODEL := RT-ACRH17
DEVICE_DTS := qcom-ipq4019-rt-acrh17
BLOCKSIZE := 128k
PAGESIZE := 2048
DTB_SIZE := 65536
IMAGE_SIZE := 20439364
FILESYSTEMS := squashfs
UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC82U')
KERNEL_INITRAMFS := $$(KERNEL) | uImage none
KERNEL_INITRAMFS_SUFFIX := -factory.trx
IMAGES := sysupgrade.bin
DEVICE_PACKAGES := ipq-wifi-asus_rt-acrh17 ath10k-firmware-qca9984 kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += asus_rt-acrh17
define Device/avm_fritzbox-4040
$(call Device/FitImageLzma)
DEVICE_VENDOR := AVM
DEVICE_MODEL := FRITZ!Box 4040
DEVICE_DTS := qcom-ipq4018-fritz4040
DEVICE_DTS := qcom-ipq4018-fritzbox-4040
BOARD_NAME := fritz4040
IMAGE_SIZE := 29056k
UBOOT_PATH := $(STAGING_DIR_IMAGE)/uboot-fritz4040.bin
UBOOT_PARTITION_SIZE := 524288
IMAGES = sysupgrade.bin
IMAGE/eva.bin := append-uboot | pad-to $$$$(UBOOT_PARTITION_SIZE) | append-kernel | append-rootfs | pad-rootfs
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
DEVICE_PACKAGES := fritz-tffs fritz-caldata
endef
TARGET_DEVICES += avm_fritzbox-4040
define Device/avm_fritzbox-7530
$(call Device/FitImageLzma)
DEVICE_VENDOR := AVM
DEVICE_MODEL := FRITZ!Box 7530
DEVICE_DTS := qcom-ipq4019-fritzbox-7530
DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand
IMAGES := sysupgrade.bin
endef
TARGET_DEVICES += avm_fritzbox-7530
define Device/avm_fritzrepeater-1200
$(call Device/FitImageLzma)
DEVICE_VENDOR := AVM
DEVICE_MODEL := FRITZ!Repeater 1200
DEVICE_DTS := qcom-ipq4019-fritzrepeater-1200
DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand ipq-wifi-avm_fritzrepeater-1200
IMAGES := sysupgrade.bin
endef
TARGET_DEVICES += avm_fritzrepeater-1200
define Device/avm_fritzrepeater-3000
$(call Device/FitImageLzma)
DEVICE_VENDOR := AVM
DEVICE_MODEL := FRITZ!Repeater 3000
DEVICE_DTS := qcom-ipq4019-fritzrepeater-3000
DEVICE_PACKAGES := ath10k-firmware-qca9984 fritz-caldata fritz-tffs-nand
IMAGES := sysupgrade.bin
endef
TARGET_DEVICES += avm_fritzrepeater-3000
define Device/compex_wpj428
$(call Device/FitImage)
DEVICE_VENDOR := Compex
DEVICE_MODEL := WPJ428
DEVICE_DTS := qcom-ipq4028-wpj428
DEVICE_DTS_CONFIG := config@4
BLOCKSIZE := 64k
IMAGE_SIZE := 31232k
KERNEL_SIZE := 4096k
IMAGES = sysupgrade.bin cpximg-6a04.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
IMAGE/cpximg-6a04.bin := append-kernel | append-rootfs | pad-rootfs | mkmylofw_32m 0x8A2 3
DEVICE_PACKAGES := kmod-gpio-beeper
endef
TARGET_DEVICES += compex_wpj428
define Device/engenius_eap1300
$(call Device/FitImage)
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := EAP1300
DEVICE_DTS := qcom-ipq4018-eap1300
DEVICE_DTS_CONFIG := config@4
BOARD_NAME := eap1300
KERNEL_SIZE := 5120k
IMAGE_SIZE := 25344k
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
endef
TARGET_DEVICES += engenius_eap1300
define Device/engenius_ens620ext
$(call Device/FitImage)
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := ENS620EXT
DEVICE_DTS := qcom-ipq4018-ens620ext
DEVICE_DTS_CONFIG := config@4
BLOCKSIZE := 64k
PAGESIZE := 256
BOARD_NAME := ENS620EXT
VENDOR_ID := 0x0101
PRODUCT_ID := 0x79
PRODUCT_ID_NEW := 0xA4
DATECODE := 190507
FW_VER := 3.1.2
FW_VER_NEW := 3.5.6
CW_VER := 1.8.99
IMAGE_SIZE := 21312k
KERNEL_SIZE := 5120k
FILESYSTEMS := squashfs
IMAGES := sysupgrade.bin factory_30.bin factory_35.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | append-metadata
IMAGE/factory_30.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | SenaoFW $$$$(PRODUCT_ID) $$$$(FW_VER)
IMAGE/factory_35.bin := qsdk-ipq-factory-nor | check-size $$$$(IMAGE_SIZE) | SenaoFW $$$$(PRODUCT_ID_NEW) $$$$(FW_VER_NEW)
endef
TARGET_DEVICES += engenius_ens620ext
define Device/glinet_gl-b1300
$(call Device/FitImage)
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-B1300
BOARD_NAME := gl-b1300
DEVICE_DTS := qcom-ipq4029-gl-b1300
BOARD_NAME := gl-b1300
KERNEL_SIZE := 4096k
IMAGE_SIZE := 26624k
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel |append-rootfs | pad-rootfs | append-metadata
endef
TARGET_DEVICES += glinet_gl-b1300
define Device/hugo_ac1200
$(call Device/FitImage)
DEVICE_VENDOR := Hugo
DEVICE_MODEL := AC1200
BOARD_NAME := hugo_ac1200
DEVICE_DTS := qcom-ipq4019-hugo-ac1200
KERNEL_SIZE := 4096k
IMAGE_SIZE := 31232k
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
DEVICE_PACKAGES := ipq-wifi-hugo_ac1200
endef
TARGET_DEVICES += hugo_ac1200
define Device/linksys_ea6350v3
# The Linksys EA6350v3 has a uboot bootloader that does not
# support either booting lzma kernel images nor booting UBI
# partitions. This uboot, however, supports raw kernel images and
# gzipped images.
#
# As for the time of writing this, the device will boot the kernel
# from a fixed address with a fixed length of 3MiB. Also, the
# device has a hard-coded kernel command line that requieres the
# rootfs and alt_rootfs to be in mtd11 and mtd13 respectively.
# Oh... and the kernel partition overlaps with the rootfs
# partition (the same for alt_kernel and alt_rootfs).
#
# If you are planing re-partitioning the device, you may want to
# keep those details in mind:
# 1. The kernel adresses you should honor are 0x00000000 and
# 0x02800000 respectively.
# 2. The kernel size (plus the dtb) cannot exceed 3.00MiB in size.
# 3. You can use 'zImage', but not a raw 'Image' packed with lzma.
# 4. The kernel command line from uboot is harcoded to boot with
# rootfs either in mtd11 or mtd13.
$(call Device/FitzImage)
DEVICE_VENDOR := Linksys
DEVICE_MODEL := EA6350
DEVICE_VARIANT := v3
DEVICE_DTS := qcom-ipq4018-ea6350v3
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 3072k
IMAGE_SIZE := 37888k
UBINIZE_OPTS := -E 5
IMAGES := factory.bin sysupgrade.bin
IMAGE/factory.bin := append-kernel | append-uImage-fakehdr filesystem | pad-to $$$${KERNEL_SIZE} | append-ubi | linksys-image type=EA6350v3
DEVICE_PACKAGES := uboot-envtools
endef
TARGET_DEVICES += linksys_ea6350v3
define Device/linksys_ea8300
$(call Device/FitzImage)
DEVICE_VENDOR := Linksys
DEVICE_MODEL := EA8300
DEVICE_DTS := qcom-ipq4019-ea8300
KERNEL_SIZE := 3072k
IMAGE_SIZE := 87040k
BLOCKSIZE := 128k
PAGESIZE := 2048
UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
IMAGES := sysupgrade.bin factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$${KERNEL_SIZE} | append-ubi | linksys-image type=EA8300
DEVICE_PACKAGES := uboot-envtools ath10k-firmware-qca9888 ipq-wifi-linksys_ea8300 kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += linksys_ea8300
define Device/meraki_mr33
$(call Device/FitImage)
DEVICE_VENDOR := Cisco Meraki
DEVICE_MODEL := MR33
DEVICE_DTS := qcom-ipq4029-mr33
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGES = sysupgrade.bin
DEVICE_PACKAGES := -swconfig ath10k-firmware-qca9887
endef
TARGET_DEVICES += meraki_mr33
define Device/mobipromo_cm520-79f
$(call Device/FitzImage)
$(call Device/UbiFit)
DEVICE_VENDOR := MobiPromo
DEVICE_MODEL := CM520-79F
DEVICE_DTS := qcom-ipq4019-cm520-79f
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := ipq-wifi-mobipromo_cm520-79f kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += mobipromo_cm520-79f
define Device/netgear_ex61x0v2
$(call Device/DniImage)
DEVICE_DTS_CONFIG := config@4
NETGEAR_BOARD_ID := EX6150v2series
NETGEAR_HW_ID := 29765285+16+0+128+2x2
endef
define Device/netgear_ex6100v2
$(call Device/netgear_ex61x0v2)
DEVICE_VENDOR := Netgear
DEVICE_MODEL := EX6100
DEVICE_VARIANT := v2
DEVICE_DTS := qcom-ipq4018-ex6100v2
endef
TARGET_DEVICES += netgear_ex6100v2
define Device/netgear_ex6150v2
$(call Device/netgear_ex61x0v2)
DEVICE_VENDOR := Netgear
DEVICE_MODEL := EX6150
DEVICE_VARIANT := v2
DEVICE_DTS := qcom-ipq4018-ex6150v2
endef
TARGET_DEVICES += netgear_ex6150v2
define Device/openmesh_a42
$(call Device/FitImageLzma)
DEVICE_VENDOR := OpenMesh
DEVICE_MODEL := A42
DEVICE_DTS := qcom-ipq4018-a42
DEVICE_DTS_CONFIG := config@om.a42
BLOCKSIZE := 64k
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
IMAGE_SIZE := 15616k
IMAGES = factory.bin sysupgrade.bin
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A42
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
DEVICE_PACKAGES := uboot-envtools
endef
TARGET_DEVICES += openmesh_a42
define Device/openmesh_a62
$(call Device/FitImageLzma)
DEVICE_VENDOR := OpenMesh
DEVICE_MODEL := A62
DEVICE_DTS := qcom-ipq4019-a62
DEVICE_DTS_CONFIG := config@om.a62
BLOCKSIZE := 64k
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
IMAGE_SIZE := 15552k
IMAGES = factory.bin sysupgrade.bin
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A62
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
DEVICE_PACKAGES := ath10k-firmware-qca9888 uboot-envtools
endef
TARGET_DEVICES += openmesh_a62
define Device/qcom_ap-dk01.1-c1
DEVICE_VENDOR := Qualcomm Atheros
DEVICE_MODEL := AP-DK01.1
DEVICE_VARIANT := C1
BOARD_NAME := ap-dk01.1-c1
DEVICE_DTS := qcom-ipq4019-ap.dk01.1-c1
KERNEL_INSTALL := 1
KERNEL_SIZE := 4096k
IMAGE_SIZE := 26624k
$(call Device/FitImage)
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$${KERNEL_SIZE} | append-rootfs | pad-rootfs | append-metadata
endef
TARGET_DEVICES += qcom_ap-dk01.1-c1
define Device/qcom_ap-dk04.1-c1
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Qualcomm Atheros
DEVICE_MODEL := AP-DK04.1
DEVICE_VARIANT := C1
DEVICE_DTS := qcom-ipq4019-ap.dk04.1-c1
KERNEL_INSTALL := 1
KERNEL_SIZE := 4048k
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := ap-dk04.1-c1
endef
TARGET_DEVICES += qcom_ap-dk04.1-c1
define Device/p2w_r619ac
$(call Device/FitzImage)
$(call Device/UbiFit)
DEVICE_VENDOR := P&W
DEVICE_MODEL := R619AC
DEVICE_DTS := qcom-ipq4019-r619ac
DEVICE_DTS_CONFIG := config@10
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGES += nand-factory.bin
IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
DEVICE_PACKAGES := ipq-wifi-p2w_r619ac
endef
TARGET_DEVICES += p2w_r619ac
define Device/p2w_r619ac-128m
$(call Device/FitzImage)
$(call Device/UbiFit)
DEVICE_VENDOR := P&W
DEVICE_MODEL := R619AC
DEVICE_VARIANT := 128M
DEVICE_DTS := qcom-ipq4019-r619ac-128m
DEVICE_DTS_CONFIG := config@10
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := ipq-wifi-p2w_r619ac
endef
TARGET_DEVICES += p2w_r619ac-128m
define Device/qxwlan_e2600ac-c1
$(call Device/FitImage)
DEVICE_VENDOR := Qxwlan
DEVICE_MODEL := E2600AC
DEVICE_VARIANT := C1
BOARD_NAME := e2600ac-c1
DEVICE_DTS := qcom-ipq4019-e2600ac-c1
KERNEL_SIZE := 4096k
IMAGE_SIZE := 31232k
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac
endef
TARGET_DEVICES += qxwlan_e2600ac-c1
define Device/qxwlan_e2600ac-c2
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Qxwlan
DEVICE_MODEL := E2600AC
DEVICE_VARIANT := C2
DEVICE_DTS := qcom-ipq4019-e2600ac-c2
KERNEL_INSTALL := 1
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac
endef
TARGET_DEVICES += qxwlan_e2600ac-c2
define Device/zyxel_nbg6617
$(call Device/FitImageLzma)
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := NBG6617
DEVICE_DTS := qcom-ipq4018-nbg6617
ROOTFS_SIZE := 24960k
RAS_BOARD := NBG6617
RAS_ROOTFS_SIZE := 19840k
RAS_VERSION := "$(VERSION_DIST) $(REVISION)"
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
IMAGES := sysupgrade.bin factory.bin
# The ZyXEL firmware allows flashing thru the web-gui only when the rootfs is
# at least as large as the one of the initial firmware image (not the current
# one on the device). This only applies to the Web-UI, the bootlaoder ignores
# this minimum-size. However, the larger image can be flashed both ways.
IMAGE/factory.bin := append-rootfs | pad-rootfs | pad-to 64k | check-size $$$$(ROOTFS_SIZE) | zyxel-ras-image separate-kernel
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | check-size $$$$(ROOTFS_SIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata
DEVICE_PACKAGES := uboot-envtools kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += zyxel_nbg6617
define Device/zyxel_wre6606
$(call Device/FitImage)
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := WRE6606
DEVICE_DTS := qcom-ipq4018-wre6606
DEVICE_DTS_CONFIG := config@4
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
DEVICE_PACKAGES := -kmod-ath10k -ath10k-firmware-qca4019 \
kmod-ath10k-ct-smallbuffers ath10k-firmware-qca4019-ct
endef
TARGET_DEVICES += zyxel_wre6606
$(eval $(call BuildImage))
Reference in New Issue View Git Blame Copy Permalink