ramips: add support for TP-Link Archer C5 v4
TP-Link Archer C5 v4 is a dual band router with 5 GbE ports Advertised as AC1200 for its 867Mbps (2×2) 5GHz band and 300 Mbps (2×2) 2.4GHz band. Specs: - SoC: MediaTek MT7620A - Ethernet: 5 GbE ports (Realtek RTL8367S) - Wireless 2.4GHz: MediaTek MT7620A - Wireless 5GHz: MediaTek MT7612E - RAM: 64MiB - ROM: 8MiB (GD25Q64CSIG) - 1 USB 2.0 port - 2 Buttons (WPS and reset) - 8 LEDs Flash instructions: Currently one has to install OpenWrt only via the serial console 1. Rename the factory.bin to to test.bin 2. start a TFTP server from IP address 192.168.0.225 and serve the image named test.bin 3. connect your device to the LAN port 4. power up the router and press 4 on the console to stop the boot process. 5. enter the following commands on the router console tftp 0x80060000 test.bin erase tplink 0x20000 0x7a0000 cp.b 0x80060000 0x20000 0x7a0000 reset Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
This commit is contained in:
Deng Qingfang
CN_SZTL
parent
f22581a84b
commit
7a74dab129
205
target/linux/ramips/dts/mt7620a_tplink_archer-c5-v4.dts
Normal file
205
target/linux/ramips/dts/mt7620a_tplink_archer-c5-v4.dts
Normal file
@ -0,0 +1,205 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include "mt7620a.dtsi"
|
||||
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
|
||||
/ {
|
||||
compatible = "tplink,archer-c5-v4", "ralink,mt7620a-soc";
|
||||
model = "TP-Link Archer C5 v4";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power;
|
||||
led-failsafe = &led_power;
|
||||
led-running = &led_power;
|
||||
led-upgrade = &led_power;
|
||||
label-mac-device = ðernet;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200";
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power: power {
|
||||
label = "archer-c5-v4:green:power";
|
||||
gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wlan2g {
|
||||
label = "archer-c5-v4:green:wlan2g";
|
||||
gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wlan5g {
|
||||
label = "archer-c5-v4:green:wlan5g";
|
||||
gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
wan {
|
||||
label = "archer-c5-v4:green:wan";
|
||||
gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wan_orange {
|
||||
label = "archer-c5-v4:orange:wan";
|
||||
gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
lan {
|
||||
label = "archer-c5-v4:green:lan";
|
||||
gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
usb {
|
||||
label = "archer-c5-v4:green:usb";
|
||||
gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
|
||||
trigger-sources = <&ohci_port1>, <&ehci_port1>;
|
||||
linux,default-trigger = "usbport";
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "archer-c5-v4:green:wps";
|
||||
gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
rfkill {
|
||||
label = "rfkill";
|
||||
gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RFKILL>;
|
||||
};
|
||||
};
|
||||
|
||||
rtl8367s {
|
||||
compatible = "realtek,rtl8367b";
|
||||
cpu_port = <7>;
|
||||
realtek,extif2 = <1 0 1 1 1 1 1 1 2>;
|
||||
mii-bus = <&mdio0>;
|
||||
phy_id = <29>;
|
||||
};
|
||||
};
|
||||
|
||||
&gpio2 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <80000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@20000 {
|
||||
compatible = "tplink,firmware";
|
||||
label = "firmware";
|
||||
reg = <0x20000 0x7a0000>;
|
||||
};
|
||||
|
||||
partition@7c0000 {
|
||||
label = "config";
|
||||
reg = <0x7c0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
rom: partition@7d0000 {
|
||||
label = "rom";
|
||||
reg = <0x7d0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@7e0000 {
|
||||
label = "romfile";
|
||||
reg = <0x7e0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
radio: partition@7f0000 {
|
||||
label = "radio";
|
||||
reg = <0x7f0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
state_default: pinctrl0 {
|
||||
gpio {
|
||||
ralink,group = "i2c", "uartf", "ephy", "rgmii2";
|
||||
ralink,function = "gpio";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ðernet {
|
||||
pinctrl-names = "default";
|
||||
mtd-mac-address = <&rom 0xf100>;
|
||||
pinctrl-0 = <&rgmii1_pins &mdio_pins>;
|
||||
|
||||
port@5 {
|
||||
status = "okay";
|
||||
mediatek,fixed-link = <1000 1 1 1>;
|
||||
phy-mode = "rgmii";
|
||||
};
|
||||
|
||||
mdio0: mdio-bus {
|
||||
status = "okay";
|
||||
reset-gpios = <&gpio2 20 GPIO_ACTIVE_LOW>;
|
||||
reset-delay-us = <10000>;
|
||||
};
|
||||
};
|
||||
|
||||
&ehci {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ohci {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wmac {
|
||||
ralink,mtd-eeprom = <&radio 0>;
|
||||
mtd-mac-address = <&rom 0xf100>;
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
wifi@0,0 {
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
mediatek,mtd-eeprom = <&radio 0x8000>;
|
||||
ieee80211-freq-limit = <5000000 6000000>;
|
||||
mtd-mac-address = <&rom 0xf100>;
|
||||
mtd-mac-address-increment = <2>;
|
||||
};
|
||||
};
|
||||
@ -1003,6 +1003,19 @@ define Device/tplink_archer-c2-v1
|
||||
endef
|
||||
TARGET_DEVICES += tplink_archer-c2-v1
|
||||
|
||||
define Device/tplink_archer-c5-v4
|
||||
$(Device/Archer)
|
||||
TPLINK_FLASHLAYOUT := 8Mmtk
|
||||
TPLINK_HWID := 0x04DA857C
|
||||
TPLINK_HWREV := 0x0C000600
|
||||
TPLINK_HWREVADD := 0x04000000
|
||||
IMAGES += factory.bin
|
||||
DEVICE_MODEL := Archer C5
|
||||
DEVICE_VARIANT := v4
|
||||
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-usb-ledtrig-usbport kmod-mt76x2 kmod-switch-rtl8367b
|
||||
endef
|
||||
TARGET_DEVICES += tplink_archer-c5-v4
|
||||
|
||||
define Device/tplink_archer-c50-v1
|
||||
$(Device/tplink-v2)
|
||||
SOC := mt7620a
|
||||
|
||||
@ -194,6 +194,11 @@ tplink,archer-c20i)
|
||||
ucidef_set_led_switch "lan" "lan" "$boardname:blue:lan" "switch0" "0x1e"
|
||||
ucidef_set_led_switch "wan" "wan" "$boardname:blue:wan" "switch0" "0x01"
|
||||
;;
|
||||
tplink,archer-c5-v4)
|
||||
ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch1" "0x0f"
|
||||
ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch1" "0x10"
|
||||
ucidef_set_led_netdev "wlan2g" "wlan2g" "$boardname:green:wlan2g" "wlan1"
|
||||
;;
|
||||
tplink,archer-c50-v1)
|
||||
ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x1e"
|
||||
ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x01"
|
||||
|
||||
@ -207,6 +207,10 @@ ramips_setup_interfaces()
|
||||
ucidef_add_switch "switch0" \
|
||||
"1:lan:3" "2:lan:4" "3:lan:1" "4:lan:2" "0:wan" "6@eth0"
|
||||
;;
|
||||
tplink,archer-c5-v4)
|
||||
ucidef_add_switch "switch1" \
|
||||
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "4:wan" "7@eth0"
|
||||
;;
|
||||
tplink,archer-mr200)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0:lan" "1:lan" "2:lan" "3:lan" "6t@eth0"
|
||||
|
||||
Loading…
Reference in New Issue
Block a user