The ide-drive option was renamed to ide-hd in qemu 6.0.
With this change qemu is starting again on Debian 12.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 497012ab4e)
U-Boot with enabled secure-boot will not boot images with the
@-character used for hash node-names.
Use the existing separation character configurable for each device.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 2b133ab19c)
Hardware
--------
CPU: Mediatek MT7981
RAM: 512M DDR4
FLASH: 256M NAND
ETH: MaxLinear GPY211 (2.5GbE N Base-T)
WiFi: Mediatek MT7981 (2.4GHz 2T2R:2 5GHz 3T3R:2 802.11ax)
BTN: 1x Reset
LED: 1x Multi-Color
UART Console
------------
Available below the rubber cover next to the ethernet port.
Settings: 115200 8N1
Layout:
<12V> <LAN> GND-RX-TX-VCC
Logic-Level is 3V3. Don't connect VCC to your UART adapter!
Installation Web-UI
-------------------
Upload the Factory image using the devices Web-Interface.
As the device uses a dual-image partition layout, OpenWrt can only
installed on Slot A. This requires the current active image prior
flashing the device to be on Slot B.
In case this is not the case, OpenWrt will boot only one time, returning
to the ZyXEL firmware the second boot.
If this happens, first install a ZyXEL firmware upgrade of any version
and install OpenWrt after that.
Installation TFTP / Recovery
----------------------------
This installation routine is especially useful in case of a bricked
device.
Attach to the UART console header of the device. Interrupt the boot
procedure by pressing Enter.
The bootloader has a reduced command-set available from CLI, but more
commands can be executed by abusing the atns command.
Boot a OpenWrt initramfs image available on a TFTP server at
192.168.1.66. Rename the image to nwa50axpro-openwrt-initramfs.bin.
$ atnf nwa50axpro-openwrt-initramfs.bin
$ atna 192.168.1.88
$ atns "192.168.1.66; tftpboot; setenv fdt_high 0xffffffffffffffff;
bootm"
Upon booting, set the booted image to the correct slot:
$ zyxel-bootconfig /dev/mtd9 get-status
$ zyxel-bootconfig /dev/mtd9 set-image-status 0 valid
$ zyxel-bootconfig /dev/mtd9 set-active-image 0
Copy the OpenWrt sysupgrade image to the device using scp.
Write the sysupgrade image to NAND using sysupgrade.
$ sysupgrade -n image.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit f0445746f6)
Instead of loading the whole image into the memory when generating the
sha256 sum, we load the file in chunks and update the hash incrementally
to avoid MemoryError in python. Also remove a stray empty line.
Fixes: #13056
Signed-off-by: Adones Pitogo <pitogo.adones@gmail.com>
(mention empty line removal, adds Fixes from PR)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit bdb4b78210)
DT overlays do not need relocation in order to be applied, so drop
defining the load address for dtbos.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit cff3786bd5)
These fields are used for EAX12 and EX6250v2 series, and perhaps other
devices. Compatibility is preserved with the WAX202 and WAX206.
In addition, adds the related vars to DEVICE_VARS so that the variables
work correctly with multiple devices.
References in GPL source:
https://www.downloads.netgear.com/files/GPL/EAX12_EAX11v2_EAX15v2_GPL_V1.0.3.34_src.tar.gz
* tools/imgencoder/src/gj_enc.c
Contains code that generates the encrypted image.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
(cherry picked from commit 0a1ebccc87)
This improves compatibility with the elder stock firmwares of the
following devices, which have not yet been merged into OpenWrt:
- Beeline SmartBox Pro
- Beeline SmartBox Turbo+
- WiFire S1500.NBN
Without this, OpenWrt factory image installation may fail.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
(cherry picked from commit 35a4418d39)
The armvirt target has been renamed to 'armsr' (Arm SystemReady)
after inclusion of EFI support.
Change references (including subtargets) accordingly.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit 36bf9d8610)
The use case for this is to set the kernel partition as the
EFI system partition. Versions of U-Boot with the
EFI boot manager (eficonfig and efidebug commands) will
store their boot order data on the ESP.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit 701d774f54)
Instead of generating full config nodes incl. kernel, generate minimal
config nodes for device tree overlays to be applied to the main config.
In this way, multiple device tree overlays can be applied more easily.
While at it change filenames to upstream style, ie. use dtso and dtbo
suffix for device tree overlays.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 6b01d40bfe)
Allow passing in an optional offset (PARTOFFSET) for the first partition.
If not specified this will default to 256K (512 blocks) as it has before.
For example if you want to start partition data at a 16M offset instead
of 256K, specify 'PARTOFFSET=16M'.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Partial clone is much faster without clipping history
Signed-off-by: Glen Huang <me@glenhuang.com>
[also apply to include/download.mk]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Apparently, Sercomm sets 2 padding bytes instead of 1 (ramips).
The HW version is a bit different than the one used for ramips.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Allow passing Sercomm PID from file.
Until now, Sercomm PID could only be passed as an array of hex bytes.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
There is no CONFIG_BINARY_DIR, it's CONFIG_BINARY_FOLDER.
While at it, don't parse the shell compatible .config, eval it.
Signed-off-by: Andre Heider <a.heider@gmail.com>
If CONFIG_BINARY_FOLDER is set in .config, use that instead of "bin" as
the bindir.
That allows to set that config and easily run e.g.
`./scripts/qemustart armvirt 32`.
Signed-off-by: Andre Heider <a.heider@gmail.com>
It's possible to have prebuilt tools already extracted. Add option to
just refresh the timestamps.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Host tools path may be a symbolic link. Use -H with find to follow path
links passed from command line to find command.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Allign dl_github_archieve.py to 8252511dc0
change. On supported system the sigid bit is applied to files and tar
archieve that on tar creation. This cause unreproducible tar for these
system and these bit should be dropped to produce reproducible tar.
Add the missing option following the command options used in other
scripts.
Fixes: 75ab064d2b ("build: download code from github using archive API")
Suggested-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The redundant character '0x0a' after the 192 bytes '0x00' padding broke
the factory image. We need to remove it to make things work again.
Fixes: e6769d11f3 scripts: fix missing character '0' issue in linksys image
Tested-by: Tony Butler <spudz76@gmail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The -w|--whitelist and -D|--download-dir arguments pass an additional value,
properly evaluate that.
Also allow to pass the download directory without -D|--download-dir, just as
the usage describes.
Finally fix spitting out the wrong error messages about those args.
Signed-off-by: Andre Heider <a.heider@gmail.com>
