Add regulator-boot-on parameters to vcc_sd.
Add startup-delay-us parameters to vcc_sdio.
This will improve the problem that in some SD cards are failing to boot up.
Signed-off-by: Yuan Tao <ty@wevs.org>
Abort the link-check based on the interface instead of the carrier
state. In cases where the interface is up but the carrier is down,
netifd won't case a dnsmasq reload, thus dhcp won't be active on thsi
interface.
Signed-off-by: David Bauer <mail@david-bauer.net>
The is no reason to catch the output by $() and then echo it again.
Remove the useless echos.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The legacy map version based on the IPv6 Interface Identifier in
draft-ietf-softwire-map-03 was typically used by uncommenting the LEGACY
variable in the map.sh file, which is not ideal. A proper configuration
option is needed instead.
The IPv6 Interface Identifier format described in the draft was
eventually changed in RFC7597, but is still used by some major ISPs,
including in Japan.
Signed-off-by: Remi NGUYEN VAN <remi.nguyenvan+openwrt@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
If not needed, disabling scp allows for a nice size reduction.
Dropbear executable size comparison:
153621 bytes (baseline)
133077 bytes (without scp)
In other words, we trim a total of 20544 bytes.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
ALLNET ALL-WAP02860AC is a dual-band wireless access point.
Specification
SoC: Qualcomm Atheros QCA9558
RAM: 128 MB DDR2
Flash: 16 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
5 GHz 3T3R QCA9880 Mini PCIe card
Ethernet: 1x 10/100/1000 Mbps AR8035-A, PoE capable (802.3at)
LEDS: 5x, which four are GPIO controlled
Buttons: 1x GPIO controlled
UART: 4 pin header near Mini PCIe card, starting count from white
triangle on PCB
1. VCC 3.3V, 2. GND, 3. TX, 4. RX
baud: 115200, parity: none, flow control: none
MAC addresses
Calibration data does not contain valid MAC addresses.
The calculated MAC addresses are chosen in accordance with OEM firmware.
Because of:
a) constrained environment (SNMP) when connecting through Telnet
or SSH,
b) hard-coded kernel and rootfs sizes,
c) checksum verification of kerenel and rootfs images in bootloder,
creating factory image accepted by OEM web interface is difficult,
therefore, to install OpenWrt on this device UART connection is needed.
The teardown is simple, unscrew four screws to disassemble the casing,
plus two screws to separate mainboard from the casing.
Before flashing, be sure to have a copy of factory firmware, in case You
wish to revert to original firmware.
Installation
1. Prepare TFTP server with OpenWrt initramfs-kernel image.
2. Connect to LAN port.
3. Connect to UART port.
4. Power on the device and when prompted to stop autoboot, hit any key.
5. Alter U-Boot environment with following commands:
setenv failsafe_boot bootm 0x9f0a0000
saveenv
6. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use
'setenv' to do that, then run following commands:
tftpboot 0x81000000 <openwrt_initramfs-kernel_image_name>
bootm 0x81000000
7. Wait about 1 minute for OpenWrt to boot.
8. Transfer OpenWrt sysupgrade image to /tmp directory and flash it
with:
sysupgrade -n /tmp/<openwrt_sysupgrade_image_name>
9. After flashing, the access point will reboot to OpenWrt. Wait few
minutes, until the Power LED stops blinking, then it's ready for
configuration.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[add MAC address comment to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The most recent patch added add lines in one block instead of in the
appropriate places to keep Makefiles in consistent style. Fix that.
Fixes: ff02e1561f ("pcre: add host variant of libpcre")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
34aed01ca865 mt76: mt7915: use ieee80211_free_txskb to free tx skbs
efc8669db5f9 mt76: mt7915: fix max_mpdu_size field for A-MSDU
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Dependencies are meant to express actual run-time dependencies and
strictly speaking, libselinux can be build and used on kernels without
SELinux (not in a very meaningful way, but never mind).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This commit adds a `selinux` variant to `procd` allowing to load an
SELinux policy at boot.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This driver is only used by ipq806x SoCs. Move it there and drop
dependency from ipq40xx since it's not used anywere.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[rebase on changes to previous patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
- Replace dwc3 phy patch with upstream version
- Rework the dts to use the upstream bindings
- Update changed config flags
- Rename module to reflect config name
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[fix qcom,tx-deamp_3_5db typo, refresh patches, rename kmod]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
The ssh symlink was still being created even when dbclient was disabled in the
build configuration. Fix this annoyance.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
8d9a62e4def7 mt76: mt7915: fix crash on tx rate report for invalid stations
825343467df4 mt76: fix double DMA unmap of the first buffer on 7615/7915
99804560372b mt76: mt7615: register ext_phy if DBDC is detected
93407be934b2 mt76: mt7615: move drv_own/fw_own in mt7615_mcu_ops
e7774de844e8 mt76: mt7663s: move drv_own/fw_own in mt7615_mcu_ops
a5602514ab03 mt76: mt7615: hold mt76 lock queueing wd in mt7615_queue_key_update
5c42061ce181 mt76: do not inject packets if MT76_STATE_PM is set
ae4757a0ae90 mt76: mt7615: reschedule runtime-pm receiving a tx interrupt
c4544d1e8a1a mt76: mt76s: fix oom in mt76s_tx_queue_skb_raw
dc73103874cc mt76: mt76s: move tx processing in a dedicated wq
c828c84cb134 mt76: mt7663s: move rx processing in txrx wq
2b34f2f6b0ef mt76: mt76s: move status processing in txrx wq
f957b050d848 mt76: mt76s: move tx/rx processing in 2 separate works
6fe964295bd9 mt76: mt76s: get rid of unused variable
43d6127d8851 mt76: mt7915: enable U-APSD on AP side
58774b605f1c mt76: set interrupt mask register to 0 before requesting irq
06f722d8046c mt76: mt7915: clean up and fix interrupt masking in the irq handler
2fbd6baac103 mt76: mt7615: only clear unmasked interrupts in irq tasklet
5ea8b6187da2 mt76: mt76x02: clean up and fix interrupt masking in the irq handler
f2e71f0c1b7e mt76: mt7615: do not do any work in napi poll after calling napi_complete_done()
1eb94624bb12 mt76: mt7915: do not do any work in napi poll after calling napi_complete_done()
5e0c587b9ac1 mt76: mt7915: clean up station stats polling and rate control update
9ab20dfbf7b1 mt76: mt7915: increase tx retry count
fa69dd96f9c0 mt76: mt7915: enable offloading of sequence number assignment
9816f9812adb mt76: move mt76_check_agg_ssn to driver tx_prepare calls
ad90170b0af9 mt76: mt7615: remove mtxq->agg_ssn assignment
335cd51be4c6 mt76: mt7915: simplify aggregation session check
21f7734cbb49 mt76: mt7915: add missing flags in WMM parameter settings
21182f90d947 mt76: mt7915: add Tx A-MSDU offloading support
27670514328f mt76: mt7615: use v1 MCU API on MT7615 to fix issues with adding/removing stations
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Not a large change from last time, but should fix at least one rare wave-2
crash. The htt-mgt-community builds are trimmed for supporting lots of
stations (typically 150+ stations per radio).
Tested on Netgear R7800.
Signed-off-by: Michael Yartys <michael.yartys@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Bump PKG_RELEASE for the affected packages as replacing "which" by
"command -v" represents a content change.
Fixes: 1fdf6b745c ("treewide: replace `which` with `command -v`")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fix shellcheck SC2230
> which is non-standard. Use builtin 'command -v' instead.
Using `command -v` is POSIX compliant while `which` is not. Also to
mention, `command -v` is a shell builtin whereas `which` is a separate
busybox applet.
Once applied to everything concerning OpenWrt we can disable the busybox
feature `which` and save 3.8kB.
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Paul Spooren <mail@aparcar.org>
[also replace cases in zram-swap]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
