Patches weren't refreshed when r8168 was updated to v8.054.00 in a85e18b53f.
Fixes: a85e18b53f ("kernel: r8168: update to v8.054.00")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 6490c88c75)
Mark the package as nonshared to build it in the target specific build
step 1 of the build bots instead of the architecture generic build step 2.
In the build step 2 it may be left out if we build it using a different
target.
Fixes: #16857
Link: https://github.com/openwrt/openwrt/pull/16859
Signed-off-by: Robert Marko <robimarko@gmail.com>
Partial, single-target update extracted from https://github.com/openwrt/openwrt/commit/d264d3a6
The previous `mac-address-increment` is deprecated, and in particular on
this target means that the kernel is unable to read the MAC address,
causing the system to boot with a new random MAC address each time.
Fixes: https://github.com/openwrt/openwrt/issues/13992
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[rafal.boni@gmail.com: single-target-specific backport from larger change]
Signed-off-by: Rafal Boni <rafal.boni@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16858
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifying GPIO_ACTIVE_HIGH on the GPIO for the voltage regulator doesn't
suffice. The regulator itself requires enable-active-high to be set.
Fixes: #16292
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Link: https://github.com/openwrt/openwrt/pull/16839
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix in commit 25eead21c5 ("ath79: fix 5GHz on QCA9886 variant of ZTE MF286")
was incomplete. A user of such variant popped up, and in the boot log
after installation, we discovered that QCA9886 expects different
pre-calibration data size, than the older QCA9880 variant:
ath10k_pci 0000:00:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000
ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
ath10k_pci 0000:00:00.0: firmware ver 10.4b-ct-9888-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 59e741e7
ath10k_pci 0000:00:00.0: invalid calibration data length in nvmem-cell 'pre-calibration': 2116 != 12064
ath10k_pci 0000:00:00.0: Loading BDF type 0
ath10k_pci 0000:00:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0056,subsystem-vendor=0000,subsystem-device=0000 from ath10k/QCA9888/hw2.0/board-2.bin
ath10k_pci 0000:00:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9888/hw2.0
ath10k_pci 0000:00:00.0: failed to fetch board file: -12
ath10k_pci 0000:00:00.0: could not probe fw (-12)
Explicitly define a pre-calibration nvmem-cell for this variant, and use
it instead of the calibration one, which is shorter.
Fixes: 25eead21c5 ("ath79: fix 5GHz on QCA9886 variant of ZTE MF286")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit fc236f3b3c)
Link: https://github.com/openwrt/openwrt/pull/16810
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Partial, single-target update extracted from https://github.com/openwrt/openwrt/commit/d264d3a6
The previous `mac-address-increment` is deprecated, and in particular on
this target means that the kernel is unable to read the MAC address,
causing the system to boot with a new random MAC address each time.
Fixes: https://github.com/openwrt/openwrt/issues/15238
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[rafal.boni@gmail.com: single-target-specific backport from larger change]
Signed-off-by: Rafal Boni <rafal.boni@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16774
Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit ec8f647d16, as with the
current kernel version, the change actually causes the same bug it once
may have fixed -- that is, the leds are now again reversed.
I suspect this was due to a switch to a newer kernel version between when
the patch was submitted and now reversing the order of the interfaces, so
that eth0 / the LAN interface is also the interface used for PoE, and eth1
/ the WAN interface is the non-PoE interface.
Signed-off-by: Rafal Boni <rafal.boni@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16779
(cherry picked from commit b5e1544f4d)
Signed-off-by: Rafal Boni <rafal.boni@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16822
Signed-off-by: Robert Marko <robimarko@gmail.com>
It should be debounce-interval, as with the others.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16802
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch adds support for the MikroTik RouterBOARD 750 r2, marketed as
hEX lite, a small indoor router with 5x 10/100 Mbps Ethernet ports, one
with PoE in. The device was already supported by the ar71xx target.
Specifications:
- SoC: Qualcomm Atheros QCA9533
- Flash: 16 MB SPI NOR
- RAM: 64 MB
- Ethernet: 4x 10/100 Mbps LAN, 1x 10/100 Mbps WAN (PoE in)
- LEDs: 5x Ethernet port activity (green), 1x user (green)
- Buttons: 1x reset
See https://mikrotik.com/product/RB750r2 for more details.
Not working:
- Serial port (already not working in ar71xx)
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Only the
"Internet" port will ask for an initramfs image. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
(cherry picked from commit 8486c677b8)
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Link: https://github.com/openwrt/openwrt/pull/13477
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix unexpected syntax error cuased by sed replacement.
Fixes: a3403720e3 ("rockchip: fix usb power for ariaboard photonicat")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit fe693f3429)
Add support for W25N01JW, W25N02JWZEIF, W25N512GW, W25N02KWZEIR and W25N01GWZEIG.
Add support for W25N04KV.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 13aa1fad5d)
From the upstream repo:
Instead of assuming only one register is used, track all 16 regs
individually.
This avoids need for the 'PREV_PAYLOAD' hack and also avoids the need to
clear out old flags:
When we see that register 'x' will be written to, that register state is
reset automatically.
Existing dissector decodes
ip saddr 1.2.3.4 meta l4proto tcp
... as
-s 6.0.0.0 -p tcp
iptables-nft -s 1.2.3.4 -p tcp is decoded correctly because the expressions
are ordered like:
meta l4proto tcp ip saddr 1.2.3.4
|
... and 'meta l4proto' did clear the PAYLOAD flag.
The simpler fix is:
ctx->flags &= ~NFT_XT_CTX_PAYLOAD;
in nft_parse_cmp(), but that breaks dissection of '1-42', because
the second compare ('cmp lte 42') will not find the
payload expression anymore.
This commit fixes#11169 and openwrt/packages#22727, and potentially anyone that uses iptables-nft legacy support.
Signed-off-by: Rodrigo B. de Sousa Martins <rodrigo.sousa.577@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16504
[Added patch header]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 44b1993f76)
It seems that some Xiaomi AX3000T boards changed to using Winbond W25N01KV
SPI-NAND which is not supported in OpenWrt 23.05 but only in main.
So, backport the support for Winbond W25N01KV from Linux 6.12 to 23.05
as well.
Link: https://github.com/openwrt/openwrt/pull/16669
Signed-off-by: Robert Marko <robimarko@gmail.com>
b66b9a1 wireless-regdb: update regulatory database based on preceding changes
5097b4a wireless-regdb: Update regulatory info for Tanzania (TZ) for 2024
29633a6 wireless-regdb: Update regulatory info for Pakistan (PK) for 2024
b44edb2 wireless-regdb: Update regulatory info for Serbia (RS) for 2024
dbfae47 Revert "wireless-regdb: Update regulatory info for Serbia (SR) for 2024"
8e3d27c wireless-regdb: Correct regulatory rules of 6GHz frequency for Türkiye (TR)
8760bc3 wireless-regdb: Update regulatory info for Honduras (HN) for 2023
3ba2c53 wireless-regdb: Update regulatory info for Israel (IL) for 2021
83c175c wireless-regdb: Update regulatory info for Kuwait (KW) for 2022
388c80c wireless-regdb: Update regulatory info for Serbia (SR) for 2024
bf55ed4 wireless-regdb: Add .b4-config
3afe172 wireless-regdb: Update .gitignore
3b34761 wireless-regdb: Correct regulatory rules for China (CN)
003c282 wireless-regdb: Update regulatory info for Philippines (PH) on 6GHz
21fcb86 wireless-regdb: Update regulatory info for Guatemala (GT) for 2020
158f105 wireless-regdb: Update regulatory info for Bahrain (BH) for 2024
218d146 wireless-regdb: Add regulatory info for Namibia (NA) for 2023
aad0c26 wireless-regdb: Update regulatory info for Togo (TG) for 2022
983f551 wireless-regdb: Update regulatory info for El Salvador (SV) on 6GHz
58575b4 wireless-regdb: Update regulatory info for Peru (PE) on 6GHz
bad3985 wireless-regdb: Update regulatory info for New Zealand (NZ) for 2022
c7d1083 wireless-regdb: Update regulatory info for Qatar (QA) on 6GHz
Signed-off-by: Itay Shoshani <itai.sho@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16678
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit a6de2d7784)
Upstream commit 9ba0cae3cac07c21c583f9ff194f74043f90d29c made FSL_IFC
visible and selectable, which means that in order for MTD_NAND_FSL_IFC
to work, it needs these two extra CONFIG options.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16717
Signed-off-by: Robert Marko <robimarko@gmail.com>
This allows the llvm toolchain to be executed on different host.
Also add it to strip list.
Fixes: 0ac0840088 ("sdk: ship llvm toolchain")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 9bd9e0a19a)
This commit adds support for netis N6 WiFi 6 router.
Specification
-------------
- SoC : MediaTek MT7621AT, MIPS, 880 MHz
- RAM : 256 MiB
- Flash : NAND 128 MiB (ESMT PSU1GA30DT)
- WLAN : MT7905DAN + MT7975DN
- 2.4 GHz : b/g/n/ax, 574 Mbps, MIMO 2x2
- 5 GHz : a/n/ac/ax, 1201 Mbps, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x5 (1x WAN, 4x LAN)
- USB : 1x 3.0
- UART : 3.3V, 115200n8
- Buttons : 1x Reset
1x WPS
- LEDs : 1x Power (green)
1x System (green)
1x WAN (green)
1x WiFi 2.4 GHz (green), controlled by phy
1x WiFi 5 GHz (green), controlled by phy
1x WPS (green)
1x USB (green)
5x ethernet leds (green), controlled by switch
- Power : 12 VDC, 1.5 A
Installation
------------
1. Update the router using stock firmware web interface and OpenWrt
factory.bin image.
Recovery and return to stock
----------------------------
1. Assign your PC a static IP 192.168.1.2 and connect to the router using
the ethernet cable;
2. Power off the router;
3. Press Reset button, power on the router and wait until ethernet led
start blinking;
4. Release the button;
5. Open http://192.168.1.1/ (N6 System Recovery Mode) in your browser;
6. Upload OpenWrt factory.bin (or stock firmware *.bin) image and proceed
with upgrade.
MAC addresses
-------------
+---------+-------------------+
| | MAC example |
+---------+-------------------+
| LAN | dc:xx:xx:49:xx:04 |
| WAN | dc:xx:xx:49:xx:05 |
| WLAN 2g | dc:xx:xx:19:xx:06 |
| WLAN 5g | dc:xx:xx:79:xx:06 |
+---------+-------------------+
The WLAN MAC prototype was found in 'Factory', 0x4
The LAN MAC was found in 'Factory', 0x7ef20
The WAN MAC was found in 'Factory', 0x7ef26
Known issue
-----------
2.4 GHz WLAN doesn't start with mt76 driver.
Probable reason:
Original Netis N6 EEPROM contains wrong MT_EE_WIFI_CONF value (0xd2).
Other routers with the same WLAN hardware (e.g., Routerich AX1800)
have MT_EE_WIFI_CONF = 0x92.
Workaround (already included in this commit):
Extract EEPROM to a file at the first time boot and change
MT_EE_WIFI_CONF (offset 0x190) value from 0xd2 to 0x92. See
/etc/hotplug.d/firmware/11-mt76-caldata for details.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16322
(cherry picked from commit f368e2d5ec)
[ Fix merging onflicts in mt7621.mk, 10_fix_wifi_mac, platform.sh ]
[ Change ðphy4 -> &mdio in dts file ]
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16436
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
...conversion.
Commit 20736013e9 ("kernel: backport nvmem v6.6 fixes and v6.7 changes")
has caused dthe device to no longer correctly read MAC address from its
onboard 24c64 EEPROM, because "at24" driver doesn't support legacy
nvmem-cell bindings [1] - and there was an explicit config option added
to mandate that behaviour in the following patch:
820-v6.7-0002-nvmem-add-explicit-config-option-to-read-old-syntax-.patch
But some of the devices, MR33 and MR74 included, weren't converted with
that as well.
Convert the definition to use proper fixed-layout binding to fix it.
The offending change was introduced between v23.05.0 and v23.05.1, and
found by bisection:
git bisect start
# status: waiting for both good and bad commits
# good: [bd4f415efa] OpenWrt v23.05.0: adjust config defaults
git bisect good bd4f415efa
# status: waiting for bad commit, 1 good commit known
# bad: [a58a86693f] OpenWrt v23.05.1: adjust config defaults
git bisect bad a58a86693f
# good: [3d0a78add2] qualcommax: only build initramfs if CONFIG_TARGET_ROOTFS_INITRAMFS is set
git bisect good 3d0a78add2
# bad: [21e5db97c4] build: add CycloneDX SBOM JSON support
git bisect bad 21e5db97c4
# good: [89184b15cf] mediatek: add build for MT7981 RFB
git bisect good 89184b15cf
# bad: [41f27bbb6d] bcm53xx: add the latest fix version of brcm_nvram
git bisect bad 41f27bbb6d
# good: [b649b0bf71] kernel: nvmem: fix "fixed-layout" & support "mac-base"
git bisect good b649b0bf71
# bad: [20736013e9] kernel: backport nvmem v6.6 fixes and v6.7 changes
git bisect bad 20736013e9
# good: [066971615f] kernel: backport v6.6 nvmem changes
git bisect good 066971615f
# first bad commit: [20736013e9] kernel: backport nvmem v6.6 fixes and v6.7 changes
Link: [1] https://github.com/openwrt/openwrt/issues/15393#issuecomment-2212300849
Fixes: 20736013e9 ("kernel: backport nvmem v6.6 fixes and v6.7 changes")
Fixes: https://github.com/openwrt/openwrt/issues/15393
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit ccbffad1ad0ce444bc2497098a1d3d3a086a5f44)
[replace mac-address-increment with #nvmem-cell-cells]
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16624
Signed-off-by: Robert Marko <robimarko@gmail.com>
There are cases where an unavailable port is not an error, making
this error message a false-positive. The kernel log is flooded with
the messages like:
OF: graph: no port node found in /soc@0/bus@42000000/i2c@42530000/usb-typec@50
Silence this message by making it a debug message.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 17ea41eabb)
er is missing from platform_copy_config() and octeon_move_config(), so
config is lost on every sysupgrade.
(cherry-picked from commit 77037b09f3)
Signed-off-by: Jakob Haufe <sur5r@sur5r.net>
Link: https://github.com/openwrt/openwrt/pull/16518
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently, bzip2 is built with a dynamically linked library on which all
of the bzip2 tools depend on.
However, when trying to use the staging dir bzip2 during building on
Fedora 40 the following error appers:
staging_dir/host/bin/bzip2: error while loading shared libraries: libbz2.so.1.0: cannot open shared object file: No such file or directory
Looking into it, the binary is dynamically linked:
$ ldd staging_dir/host/bin/bzip2
linux-vdso.so.1 (0x00007f5ebd9ff000)
libbz2.so.1.0 => not found
libc.so.6 => /lib64/libc.so.6 (0x00007f5ebd7f5000)
/lib64/ld-linux-x86-64.so.2 (0x00007f5ebda01000)
libbz2.so.1.0 is installed into staging_dir/lib but that directory is not
evaluated for the required libraries and Fedora only ships:
/usr/lib64/libbz2.so.1
/usr/lib64/libbz2.so.1.0.8
Thus it cannot find the libbz2 that bzip2 is linked against and thus
trying to use bzip2 will fail and stop compilation as it is used for
bzip2 compressed tarballs.
So, to avoid OpenWrt compiled bzip2 to even attempt to load a required
library from the host we can just static compile libbz2 and bzip2.
Link: https://github.com/openwrt/openwrt/pull/16520
Signed-off-by: Robert Marko <robimarko@gmail.com>
The rss variant should conflict with the default.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/16460
(cherry picked from b83c7448d3)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
