Wallys DR531 is based on Qualcomm Atheros QCA9531 v2. Support for this
device was first introduced in e767980eb8 (ar71xx target).
Specifications:
- Qualcomm/Atheros QCA9531 v2
- 550/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR2)
- 8 MB of flash (SPI NOR)
- 2T2R 2.4 GHz Wi-Fi, with external PA (SE2576L), up to 30 dBm
- 2x MMCX connectors (optional IPEX/U.FL)
- mini PCIe connector (PCIe/USB buses and mini SIM slot)
- 7x LED, 1x button, 1x optional buzzer
- UART, JTAG and LED headers on PCB
Flash instruction (do it under U-Boot, using UART):
tftpb 0x80060000 openwrt-ath79-...-dr531-squashfs-sysupgrade.bin
erase 0x9f050000 +$filesize
cp.b $fileaddr 0x9f050000 $filesize
setenv bootcmd "bootm 0x9f050000"
saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The AP121FE is a slightly modified version of already supported AP121F
model (added to ar71xx in 0c6165d21a and to ath79 in 334bbc5198).
The differences in compare to AP121F:
- no micro SD card reader
- USB data lines are included in Type-A plug
- USB bus switched to device/peripheral mode (permanently, in bootstrap)
Other than that, specifications are the same:
- Atheros AR9331
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR1)
- 16 MB of flash (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz Wi-Fi, up to 15 dBm
- 1x IPEX/U.FL connector, internal PCB antenna
- 3x LED, 1x button, 1x switch
- 4-pin UART header on PCB (2 mm pitch)
- USB 2.0 Type-A plug (power and data)
Flash instruction (under U-Boot web recovery mode):
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with RJ45 port, press the reset button, power up device,
wait for first blink of all LEDs (indicates network setup), then keep
button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The ethernet setup/label MAC address for RT-AC51U and RT-AC54U are
the same, so move them into the shared DTSI.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The order of function and color in the labels in inverted for the
LAN LEDs. Fix it.
Fixes: 915966d861 ("ath79: Port PowerCloud Systems CAP324 support")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The LED color was missing in 01_leds.
Fixes: 745dee11ac ("ath79: add support for WD My Net Wi-Fi Range
Extender")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.
In ath79, we therefore requested to have in the DTS files so far,
and omit it in the DTSI files. However, essentially the syntax of
the parent ath79.dtsi file already determines the DTS version, so
putting it into the DTS files is just a useless repetition.
Consequently, this patch puts the dts-v1 statement into the parent
ath79.dtsi, which is (indirectly) included by all DTS files. All
other occurences are removed.
Since the dts-v1 statement needs to be before any other definitions,
this also moves the includes to make sure the ath79.dtsi or its
descendants are always included first.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ath79.dtsi uses ATH79_CLK_MDIO, so the include
<dt-bindings/clock/ath79-clk.h>
needs to be moved there.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
SPDX moved from GPL-2.0 to GPL-2.0-only and from GPL-2.0+ to
GPL-2.0-or-later. Reflect that in the SPDX license headers.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Move engenius_loader_okli image recipe in front of all Engenius
devices, so adding new device entries will not have them sorted
before the shared recipe.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
All modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x, lantiq/xrx200 and ath79/generic
Run-tested: ipq806x (R7800), lantiq (Easybox 904 xDSL)
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[add test on lantiq]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
First group the interfaces on the DSA switch into the
right LAN/WAN groups. Tested successfully on the
D-Link DIR-685 with the RTL8366RB DSA switch.
The RTL8366RB is DSA custom tagged and now handled
by the kernel tag parser. (Backported.)
The Vitesse switches are not capable of supporting
DSA per-port tagging. We suspect they must be handled
using some custom VLAN set-up.
Cc: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[sorted devices alphabetically]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The BCM5301x SoCs do have i2c. Since this is only
being used by the Meraki MR32, this will be packaged
as a module.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
These have made their way into -next. This patch
also includes the portion of the bcm53xx kernel
patch refreshes as the hunks in
302-ARM-dts-BCM5301X-Update-Northstar-pinctrl-binding.patch
moved slightly due to the added nodes.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The Meraki MR32 (BCM53016A1) uses the pwm to drive the
tricolor LED. The driver has been available in upstream
for a long time. Only the Device-Tree definition was
missing, but it has been queued recently.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The legacy ar71xx target is removed and multiple targets use DTS now, so
there is no need to point that out for ATH79 specifically.
Signed-off-by: Paul Spooren <mail@aparcar.org>
bluetooth on mt7622 needs a firmware to start. It can't be built-in or
it tries to load firmware before rootfs is mounted, and then fails.
build it as a kernel module to fix that.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
It turns out that 'echo -e' isn't portable; it doesn't work in the dash
builtin echo and Ubuntu users are complaining.
I can't even get octal (specified by POSIX) to work consistently because
those variants of 'echo' which *do* support -e don't seem to interpret
octalwithout it.
I could switch to /bin/echo but using -e with that isn't actually
portable *either* even though it works today.
For now just stick with bash, and use its builtin. We may end up using
something else entirely; perhaps perl.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This bug applied where mtd partition end address,
or erase start address, was not cleanly divisible by parent mtd erasesize.
This error would cause the bits following the end of the partition
to the next erasesize block boundary to be erased,
and this partition-overflow data to be written to the partition erase
address (missing additional partition offset address)
of the mtd (top) parent device.
Fixes: FS#2428
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[shorten commit title, add Fixes, fix kernel 4.19 as well]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link Archer C5 v4 is a dual band router with 5 GbE ports
Advertised as AC1200 for its 867Mbps (2×2) 5GHz band
and 300 Mbps (2×2) 2.4GHz band.
Specs:
- SoC: MediaTek MT7620A
- Ethernet: 5 GbE ports (Realtek RTL8367S)
- Wireless 2.4GHz: MediaTek MT7620A
- Wireless 5GHz: MediaTek MT7612E
- RAM: 64MiB
- ROM: 8MiB (GD25Q64CSIG)
- 1 USB 2.0 port
- 2 Buttons (WPS and reset)
- 8 LEDs
Flash instructions:
Currently one has to install OpenWrt only via the serial console
1. Rename the factory.bin to to test.bin
2. start a TFTP server from IP address 192.168.0.225 and serve the image named test.bin
3. connect your device to the LAN port
4. power up the router and press 4 on the console to stop the boot process.
5. enter the following commands on the router console
tftp 0x80060000 test.bin
erase tplink 0x20000 0x7a0000
cp.b 0x80060000 0x20000 0x7a0000
reset
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
All modifications made by update_kernel.sh/no manual intervention needed
Run-tested: ipq806x (R7800), ath79 (Archer C7v5), x86/64
No dmesg regressions, everything appears functional
Signed-off-by: John Audia <graysky@archlinux.us>
[add run test from PR]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for the Ubiquiti UniFi AP Pro to the ath79 target. The
device was previously supported on the now removed ar71xx target.
SoC Atheros AR9344
WiFi Atheros AR9344 & Atheros AR9280
ETH Atheros AR8327
RAM 128M DDR2
FLASH 16M SPI-NOR
Installation
------------
Follow the Ubiquiti TFTP recovery procedure for this device.
1. Hold down the reset button while connecting power for 10 seconds.
2. Transfer the factory image via TFTP to the AP (192.168.1.20)
3. Wait 2 minutes for the AP to write the firmware to flash. The device
will automatically reboot to OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
The tp-link safeloader devices typically contain a partition
"default-mac" which stores the MAC addresses. It is followed by other
partitions containing device info, like
{"default-mac", 0x610000, 0x00020},
{"pin", 0x610100, 0x00020},
{"product-info", 0x611100, 0x01000},
In DTS, we typically assign a 0x10000 sized partition for these,
which is mostly labelled "mac" or "info". In rarer cases, the
partitions have been enclosed in a larger "tplink" or "config"
partition.
However, when comparing different devices, the implementation appears
relatively arbitrary at the moment.
Thus, this PR aims at harmonizing these partitions by always using
the name "info" for the DTS partition containing "default-mac".
"info" is preferred over "mac" as we never just have "default-mac"
alone, but always some other device-info partitions as well.
While at it, this also establishes a similar partitioning for the
few devices where the "info" partitions are part of a bigger
unspecific "config" partition or similar.
Besides the harmonization itself, this also allows to merge a few
cases in 11-ath10k-caldata.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Router and Movie "keys" are actually switches for both devices
according to the manual. This has been properly implemented in ar71xx,
but overlooked when porting to ath79.
Fixes: 480bf28273 ("ath79: add support for Buffalo WZR-HP-AG300H")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The hardware of this device seems to be identical to WZR-HP-AG300H.
It was already implemented as a clone in ar71xx.
Specification:
- 680 MHz CPU (Qualcomm Atheros AR7161)
- 128 MiB RAM
- 32 MiB Flash
- WiFi 5 GHz a/n
- WiFi 2.4 GHz b/g/n
- 5x 1000Base-T Ethernet
- 1x USB 2.0
Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.11.1
- Go to “Administration” → “Firmware Upgrade”
- Upload the OpenWrt factory image
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link EAP225-Wall v2 is an AC1200 (802.11ac Wave-2) wall plate access
point. UART access and debricking require fine soldering.
The device was kindly provided for porting by Stijn Segers.
Device specifications:
* SoC: QCA9561 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR (GD25Q127CSIG)
* Wireless 2.4GHz (SoC): b/g/n, 2x2
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO
* Ethernet (SoC): 4× 100Mbps
* Eth0 (back): 802.3af/at PoE in
* Eth1, Eth2 (bottom)
* Eth3 (bottom): PoE out (can be toggled by GPIO)
* One status LED
* Two buttons (both work as failsafe)
* LED button, implemented as KEY_BRIGHTNESS_TOGGLE
* Reset button
Flashing instructions, requires recent firmware (tested on 1.20.0):
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface
Debricking:
* Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC)
* Bridge unpopulated resistors R162 (TXD) and R165 (RXD)
Do NOT bridge R164
* Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via sysupgrade or LuCI web interface
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From OEM ifconfig:
br0 Link encap:Ethernet HWaddr 50:...:04
eth0 Link encap:Ethernet HWaddr 50:...:04
wifi0 Link encap:UNSPEC HWaddr 50-...-04-...
wifi1 Link encap:UNSPEC HWaddr 50-...-05-...
Signed-off-by: Sander Vanheule <sander@svanheule.net>
[fix IMAGE_SIZE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The soft_config partition for these devices lays between 0xe000 and
0xf000 (as correctly detected by the RouterBoard platform driver),
before the bootloader2 partition which starts at 0x10000.
This commit correctly sorts the partitions, fixing the parsing error.
Fixes: FS#3314
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org>
This is the most popular choice in the linux kernel tree.
Within OpenWrt, this change will establish consistency with ath79
and ramips targets.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[extend commit message, include netgear_dm200, update base-files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
fdt_addr and kernel_addr variables are getting obsolete in the mainline
u-boot in favor of fdt_addr_r and kernel_addr_r.
By checking if the new variables exist, we can make sure that devices with newer
version of u-boot will work while not breaking support for the existing ones.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This imports the patch that adds bootargs-append support from IPQ40xx.
This way we can append additional boot arguments from DTS instead of only being able to overwrite them.
This way dual firmware devices can use the rootfs number that bootloader passes to decide from what to boot.
But we still need to append console info and ubi root info.
This is used by Edgecore ECW5410.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
IPQ806x series also has a GSBI1 with UART and I2C peripherals, so lets add the node for it.
Its needed for Edgecore ECW5410 which uses the UART from GSBI1 as second UART for Bluetooth.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Its needed for Edgecore ECW5410 which does not use QCA8337 switch,
but rather 2x AR8033 PHY-s directly connected to GMAC-s.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
The Buffalo devices in ath79 share their image generation code,
so let's create a shared Device definition for them.
Since most of them use BUFFALO_HWVER := 3, this is moved as
default to the shared definition as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Assign return value of kstrtoul to error variable instead of
conversion value.
Suggested-by: Birger Koblitz <git@birger-koblitz.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
