* ramips: increase HiWiFi HC5962 kernel partition to 4M
Increase kernel partition because 2M is insufficient for 4.19
Because the partition changes, previous version of OpenWrt cannot upgrade to this version
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: use all reserved space for HiWiFi HC5962
Idea was from ad6c6361f9 ("ath79: enable all space on Netgear ar9344-based WNDR routers")
These stock partitons: "backup", "hw_panic", "overly", firmware_backup", "opt"
do not contain any device-specific data and can be used for /overlay, resulting in
121M space
Users should erase those partitions with command `mtd erase <partition name>` prior to
upgrading to this version
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Co-authored-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add xiaomi_miwifi-r3 support
Specification:
- CPU: 580 MHz
- Flash size: 128 MiB NAND
- RAM size: 128 MiB DDR2
- Wireless No1: SoC-integrated: MT7620A 2x2 MIMO 802.11b/g/n (2.4 GHz)
- Wireless No2: On-board chip: MT7612E 2x2 MIMO 802.11a/n/ac (5 GHz)
- Switch: MT7620 built-in 10/100 switch w/ vlan support
- USB: 2.0 x1
Flash instructions:
1. access ssh via https://wiki.openwrt.org/toh/xiaomi/mir3
2. in ssh:
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set uart_en=1
nvram commit
mtd write lede-ramips-mt7620-miwifi-r3-squashfs-kernel1.bin kernel1
mtd write lede-ramips-mt7620-miwifi-r3-squashfs-rootfs0.bin rootfs0
reboot
If you want to revert back to stock fw while on LEDE:
insert usb stick (FAT/FAT32) with stock fw renamed to miwifi.bin
fw_setenv flag_last_success 0
power off the device
hold the reset button and power on the device, keep holding the reset button until yellow led starts blinking.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: add mt7620-nand driver for NAND flash
This add the mt7620-nand driver
and enable nand ubifs for subtarget mt7620
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Co-authored-by: Chen Minqiang <ptpt52@gmail.com>
Specification:
- CPU: 580 MHz
- Flash size: 128 MiB NAND
- RAM size: 128 MiB DDR2
- Wireless No1: SoC-integrated: MT7620A 2x2 MIMO 802.11b/g/n (2.4 GHz)
- Wireless No2: On-board chip: MT7612E 2x2 MIMO 802.11a/n/ac (5 GHz)
- Switch: MT7620 built-in 10/100 switch w/ vlan support
- USB: 2.0 x1
Flash instructions:
1. access ssh via https://wiki.openwrt.org/toh/xiaomi/mir3
2. in ssh:
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set uart_en=1
nvram commit
mtd write lede-ramips-mt7620-miwifi-r3-squashfs-kernel1.bin kernel1
mtd write lede-ramips-mt7620-miwifi-r3-squashfs-rootfs0.bin rootfs0
reboot
If you want to revert back to stock fw while on LEDE:
insert usb stick (FAT/FAT32) with stock fw renamed to miwifi.bin
fw_setenv flag_last_success 0
power off the device
hold the reset button and power on the device, keep holding the reset button until yellow led starts blinking.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Increase kernel partition because 2M is insufficient for 4.19
Because the partition changes, previous version of OpenWrt cannot upgrade to this version
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Specifications:
* SoC: MT7621AT
* RAM: 128MB
* Flash: 16MB NOR SPI flash
* WiFi: MT7615N (2.4GHz) and MT7615N (5Ghz)
* LAN: 5x1000M
* Firmware layout is Uboot with extra 96 bytes in header
* Base PCB is AP-MTKH7-0002
* LEDs Power Green,Power Orange,Internet Green,Internet Orange
* LEDs "2.4G" Green & "5G" Green connected directly to wifi module
* Buttons Reset,WPS,WIFI
Flash instruction:
Upload image via emergency recovery mode via Windows "not working with Linux"
Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable.
Give it ~30 seconds, to boot the recovery mode GUI
Connect your client computer to LAN1 of the device
Set your client IP address manually to 192.168.0.2 / 255.255.255.0.
Call the recovery page for the device at http://192.168.0.1
Use the provided emergency web GUI to upload and flash a new firmware to the device
MAC addresses:
lan factory 0xe000 *:55 (label)
wan factory 0xe006 *:58
2.4 GHz factory 0x0004 *:56
5.0 GHz factory 0x8004 *:57
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
This commit sync ramips source code from openwrt master.
1. ramips: gsw_mt7621: disable PORT 5 MAC RX/TX flow control by default
2. ramips: allow to set switchdev by board in ramips_set_preinit_iface
3. kernel: fix typos in KernelPackage description
* generic: support mtd-mac-address-ascii
It supports formats of both 001122334455 and 00:11:22:33:44:55
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* ramips: add JDCloud
Co-authored-by: Yousong Zhou <yszhou4tech@gmail.com>
SoC: MT7621AT
RAM: 256MB
Flash: 16M SPI
Ethernet: 5x GE ports
WiFi: 2.4G: MT7615N
5G: MT7615N
Flash instruction:
1.Modify the file to linux.bin
2.Set up FTP service
3.Computer settings fixed IP: 192.168.179.50 255.255.255.0
4.Turn on the power and press and hold the reset button until the indicator light is on for about 5 seconds.
Signed-off-by: Zhenjian Zhang <itdesk.zhang@gmail.com>
