We can now use the power LED for diag in more devices thanks to the latest
patches from the RPi foundation.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Use approach suggested by Adrian Schmutzler instead of introducing
another device variable.
Also revert the unnecessary white-space changes accidentally introduced
by the previous commit.
Fixed: c067b1e79b ("mediatek: move out-of-tree DTS files to dedicated dts folder")
Suggested-by: Adrian Schmutzler <mail@adrianschmutzler.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use dedicated dts folder like on ramips to store device tree source
files for boards not already supported in vanilla Linux.
Doing so instead of having them in files-* has several advantages:
* we don't need to duplicate them for several kernel versions
* changes to a device tree don't trigger a complete kernel rebuild
* the files are more obvious to find
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
No manual changes needed.
Build system: x86_64
Build-tested: bcm27xx/bcm2711
Signed-off-by: John Audia <graysky@archlinux.us>
GetABISuffix does not work for intra-package ABI version of provided symbols,
since ABIV_$(provided) is not set.
Fix ABI version by using $(ABIV_$(1)) directly
Signed-off-by: Felix Fietkau <nbd@nbd.name>
As github tarball doesn't include the files of submodules,
so switch to git source to fetch them.
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
If an external module uses exported symbols from another external
module, Kbuild needs to have full knowledge of all symbols to
avoid spitting out warnings about undefined symbols.
Use PKG_EXTMOD_SUBDIRS to point to the build directory which contains
the Module.symvers.
Pass KERNEL_MAKE_FLAGS to the external module build, to inject
KBUILD_EXTRA_SYMBOLS. KBUILD_EXTRA_SYMBOLS holds a space separated list
of Module.symvers, which list all exported symbols.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The USB ports if a FRIZZ!Box 7320 do not supply power to connected
devices.
Add the GPIOs enabling USB power as regulator, to enable USB power
supply as soon as the USB driver is loaded.
Fixes FS#3624
Signed-off-by: Mathias Kresin <dev@kresin.me>
When recursively deleting partitions, don't acquire the masters
partition lock twice. Otherwise the process endy up in a deadlocked
state.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
MediaTek MT7622
512MB DDR3 RAM
64M SPI-NOR Flash (Winbond W25Q512JV)
MediaTek MT7622 802.11bgn 4T4R WMAC
MediaTek MT7915 802.11ax 4T4R
Marvell AQR1112 100/1000/2500 NBase-T PHY
Holtek HT32F52241 LED controller
Reset Switch
UART
----
CPU UART0 at the pinout next to the Holtek MCU.
Pinout (first pin next to SoC / MCU)
0 3V3
1 RX
2 TX
3 GND
Settings are 115200 8N1.
Opening the case
----------------
Opening the case is not a nice task, as itis glued together. Insert a
flat knife between the front and back casing below the ethernet port.
Open up a gap this way and insert a flat scredriver, remove the knife.
Work your way around the casing by applying force to seperate the front
and back casing. This losens the glue and opens the plastic clips. Be
gentle, as these clips are very cheap and break quickly.
Installation
------------
1. Connect to the booted device at 192.168.1.20 using username/password
"ubnt".
2. Transfer the OpenWrt sysupgrade image to the device using SCP.
3. Check the mtd partition number for bs / kernel0 / kernel1
$ cat /proc/mtd
4. Set the bootselect flag to boot from kernel0
$ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6
5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1
$ dd if=openwrt.bin of=/dev/mtdblock8
$ dd if=openwrt.bin of=/dev/mtdblock9
6. Reboot the device. It should boot into OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add a driver for controlling the RGB LED via Ubiquitis own "LEDBAR" LED
controller based on the Holtek HT32F52241 MCU.
This driver is initially used by the Ubiquiti UniFi 6 LR, however
judging from FCC pictures the MCU is also found on the U6-Mesh as well
as the U6-Extender.
Signed-off-by: David Bauer <mail@david-bauer.net>
