Booting from non-MMC devices on Rockchip targets without this
change results in a boot failure:
Model: FriendlyElec NanoPi R5S
Net: eth0: ethernet@fe2a0000
Hit any key to stop autoboot: 0
** Booting bootflow 'nvme#0.blk#1.bootdev.part_1' with script
** No partition table - mmc 0 **
** No partition table - mmc 0 **
Couldn't find partition mmc 0:1
Can't set block device
Wrong Image Type for bootm command
ERROR -91: Protocol wrong type for socket: can't get kernel image!
Boot failed (err=1)
This change fixes the default boot script for Rockchip targets to
support booting from non-MMC devices such as NVMe or USB drives.
Some targets with only a boot rom (e.g. NanoPi R5S) may require u-boot
to be installed on the eMMC or a MicroSD card in order to boot from
non-MMC devices.
Fixes: #14420
Reviewed-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: Justin Klaassen <justin@tidylabs.app>
(cherry picked from commit 4d49ce1bde)
XHCI bus numbers are assigned dynamically, it may varies among boards,
match the device irq name with regexp, drop the hardcoded name.
Signed-off-by: Furong Xu <xfr@outlook.com>
(cherry picked from commit 314af7018a)
The expected name by the binding at this position is "msg" and the SoC's
manual also calls the interrupt in question "msg", so fix the rk356x dtsi
to use the correct name.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
All devices in the rockchip target have appended image-metadata. Enforce
the presence of this metadata to avoid flashing incomplete images.
This is the de-facto standard for almost all OpenWrt targets.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 54e52fdacb)
Hardware
--------
RockChip RK3399 ARM64 (6 cores)
4GB LPDDR3 RAM
1x 1000 Base-T
1 GPIO LED (status)
HDMI 2.0
3.5mm TRRS AV jack
Micro-SD slot
16GB eMMC
1x USB 3.0 Port
2x USB 2.0 Port
1x USB Type-C Port
1x M.2 PCI-E Port
AP6356S (BCM4356) SDIO WiFi & Bluetooth adapter
--------
Note: AP6356S is not supported yet due to the lack of firmware and NVRAM
Signed-off-by: Lu jicong <jiconglu58@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 4689114669)
Hardware
--------
RockChip RK3568 ARM64 (4 cores)
2/4/8GB LPDDR4 RAM
2x 1000 Base-T
Bluetooth 5.0
Dual-band Wi-Fi6
2 LEDs (POWER / USER)
32/64/128GB eMMC on-board
Micro-SD Slot
M.2 Slot
SATA 3.0 interfaces
HDMI 2.0
Headphone
2x USB 2.0 Port
USB 3.0 Port
DC 12V
Installation
------------
Uncompress the ImmortalWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 4194e38ac5)
Without it the WAN port won't be initialized properly.
Fixes: 8f578c15b3 ("rockchip: add NanoPi R2C support")
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit d312f12b1a)
The OrangePi R1 Plus LTS is a minor variant of OrangePi R1 Plus with
the on-board NIC chip changed from rtl8211e to yt8531c, and otherwise
identical to OrangePi R1 Plus.
Tested-by: Volkan Yetik <no3iverson@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 32d5921b8b)
[Removed patches for kernel 6.1]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Orange Pi R1 Plus is a Rockchip RK3328 based SBC by Xunlong.
This device is similar to the NanoPi R2S, and has a 16MB
SPI NOR (mx25l12805d). The reset button is changed to
directly reset the power supply, another detail is that
both network ports have independent MAC addresses.
Note: booting from SPI is currently unsupported, you have to install
the image on a SD card.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit ab641efe69)
[Removed patches for kernel 6.1]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
This set the CONFIG_FRAME_WARN option depending on some target settings.
It will use the default from the upstream kernel and not the hard coded
value of 1024 now.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 16a20512d8)
This board was designed as a clone of NanoPi R4S. However, it didn't
follow the spec and changed the power-supply system massively, and
because of it there's no way to soft reset this board currently.
For reboot, you must cut off the power and reengage it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
This allows loading modules with large memory requirements, recently needed
while testing on armvirt/32. Past forum discussions [1] and bug reports [2]
also raised this and the ipq806x target already set it in response [3].
Given this increases kernel image size by only ~1KB, is generally useful on
multi-platform kernels, and enabled by default on upstream arm32 Linux, add
it to the generic config.
The setting has similar utility on arm64, is a requirement for KASLR, and
already enabled on most OpenWrt aarch64 targets, so pull this into the
top-level generic config.
[1]: https://forum.openwrt.org/t/vmap-allocation-for-size-442368-failed-use-vmalloc-size-to-increase-size/34545/7
[2]: https://github.com/openwrt/openwrt/issues/8282
[3]: f81e148eb6 ("ipq806x: update 4.19 kernel config").
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
(cherry picked from commit c2d194a34e)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
