The TP-Link TL-MR3020 has a three-state mode slider which was previously
integrated as a button (EV_KEY). This led to spurious activations of
failsafe mode.
Set the type for the button to switch (EV_SW), to avoid unintended
activations of failsafe mode.
Related: commit 27f3f493de ("gpio-button-hotplug: unify polled and
interrupt code")
Signed-off-by: David Bauer <mail@david-bauer.net>
During porting support for this router to ath79 target
it was discovered that GPIO mapping was incorrect (GPIO11 active high).
Correct mapping for both V1 and V2 is GPIO12 active low.
Default configuration from GPL source for V2 explicitly states this, and
this was confirmed experimentally on ath79 by looking on
/sys/kernel/debug/gpio. Correctness of this was also validated for V1 by
cross-flashing vendor firmware for V1 on V2 hardware, in which reset
button also worked.
Fix it.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[slightly adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Since the wireless LED was used for boot and set up with a DT
trigger, the WiFi indication hasn't worked on ath79 at all.
In addition, a look into the manual revealed that the OEM
configuration is as follows:
LED 1 (green): power
LED 2 (green): configurable
LED 3 (red): wireless
So, let's just keep the WiFi trigger and convert the rest to its
"intended" use.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
zstd with its default settings (compression level -3) compresses better
than bzip2 -9 (which is the default setting), and is an order of magnitude
faster.
I made the following measurements for the most common compression tools
(all standard Debian Buster versions, default flags unless noted
otherwise), using the debug information of a large x86-64 kernel with
ALL_KMODS:
* kernel-debug.tar: 376M
* kernel-debug.tar.gz: 101M, compressed in ~12s
* kernel-debug.tar.bz2: 91M, compressed in ~15s
* kernel-debug.tar.xz: 57M, compressed in ~101s
* kernel-debug.tar.zst: 86M, compressed in ~1s
With zstd, there is still some room for improvement by increasing the
compression, but the slight increase in compression ratio
(22.83% -> 19.46%) does not justify the significant increase in
compression time (about 5 times on my machine) in my opinion.
Note that multithreaded compression (-T argument) does not affect
reproducibility with zstd.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
GPS time without date was previously used to set system date:
Tue Oct 10 11:48:21 2000 user.info kernel: [ 108.786639] ugps: system time differs from GPS time by more than 5 seconds. Using 2000-10-10T10:48:21 UTC as the new time
Tue Oct 10 11:49:27 2000 user.info kernel: [ 174.794699] ugps: system time differs from GPS time by more than 5 seconds. Using 2020-05-26T10:49:27 UTC as the new time
Fix this by ignoring incomplete dates and wait for complete time
information before adjusting system date/time.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The -O option for the tplink-v1-header was missing for the TP-Link
TL-WR902AC v1, while safeloader and MTDPARTS where set up with a
single firmware partition.
This led to bootloops after using sysupgrade.
Fixes: FS#3118
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Also ensure that the error message is actually printed to stderr and that
the rule generation is aborted if an interface cannot be resolved.
Ref: https://github.com/openwrt/luci/issues/3975
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The clean target tries to remove what looks like a bogus 'rbcfg',
probably carried over copy-pasta. Remove the name of the generated
executable ('fbtest') instead.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Fixes: 8099f4e0d3 ("fbtest utility ")
Add a local hack to prevent the Broadcom WPA authenticator process from
inheriting the lock descriptor 1000 used to prevent concurrent executions
of the init script.
Without this fix, repeated invocations of /etc/init.d/network, e.g. for
obtaining the enabled state, would hang forever.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Support for 64 bits has been remove on latest master of raspberry/firmware.
Update to latest commit with 64 bit support since we don't support
installing 32 bit packages on 64 bit targets.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
