The mpc85xx-generic subtarget supports the QorIQ SoCs of the p1010
family. Rename the subtarget to reflect this affiliation as it's the
case with the other mpc85xx subtargets.
Signed-off-by: David Bauer <mail@david-bauer.net>
The property "ralink,port-map" has been obsolete long before
this device was added, and the device is a one-port anyway.
Just remove it.
Fixes: 5ef79af4f8 ("ramips: add support for Ravpower WD03")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
31e99fe3da which introduced this code was unfortunately untested.
This commit fixes a number of issues and works around the fact that in
this particular scheme, the LZO payload may be padded at the end which
will trigger a harmless lzo decompression error.
This commit also disambiguates the debug printks.
Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Fixes: 31e99fe3da ("generic: platform/mikrotik: support LZOR encoding")
The bcm6345-periph-intc driver only targets a single CPU at a time, even
if the notional affinity is wider. Let's inform the core code about this.
This patch gets rid of the kernel message:
"genirq: irq_chip bcm6345-periph-intc did not update eff. affinity mask
of irq 52"
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
In file included from ./arch/mips/include/asm/io.h:34,
from ./arch/mips/include/asm/mmiowb.h:5,
from ./include/linux/spinlock.h:60,
from ./include/linux/irq.h:14,
from drivers/irqchip/irq-bcm6345-ext.c:10:
drivers/irqchip/irq-bcm6345-ext.c: In function 'bcm6345_ext_intc_of_init':
./arch/mips/include/asm/mach-bcm63xx/ioremap.h:48:9: warning: 'base' may be used uninitialized in this function [-Wmaybe-uninitialized]
return is_bcm63xx_internal_registers((unsigned long)addr);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/irqchip/irq-bcm6345-ext.c:255:16: note: 'base' was declared here
void __iomem *base;
^~~~
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
drivers/irqchip/irq-bcm6345-periph.c: In function 'bcm6345_periph_irq_handle':
drivers/irqchip/irq-bcm6345-periph.c:55:21: warning: 'block' may be used uninitialized in this function [-Wmaybe-uninitialized]
struct intc_block *block;
^~~~~
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Increase SPI frequency to 33.333 MHz. It's maximum frequency supported
by SPI Flash memory chip without Fast read opcode.
Tested on TP-Link TL-WR1043ND V2.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
While "ok" is recognized in DT parsing, only "okay" is actually
mentioned as valid value. Replace it accordingly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
While "ok" is recognized in DT parsing, only "okay" is actually
mentioned as valid value. Replace it accordingly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
While "ok" is recognized in DT parsing, only "okay" is actually
mentioned as valid value. Replace it accordingly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit removes the target-specific diag.sh script. This way, the
generic one is used for the target, which uses DT-aliases to specify the
LEDs used.
Though generic diag.sh allows to use different LEDs to indicate different
states, this patch just moves the old assignment and does not try to
"improve" the assignment by using additional colors.
However, individual proposals to do so are welcome.
For the few cases where status_led2 was used in old diag.sh, only the
primary LED was migrated.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
An e-mail response from MikroTik contained a minimal overview
on hardware option bits which mentioned a currently unknown bit.
While not being too detailed what it does, add it for documentation purposes.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Most work was done in commit 021c893658 ("ramips: fix size-cells on spi
nodes"), but a few more DTS files using the old reg style have been added
since then. This commit fixes them.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Certain SFP modules (most notably Nokia GPON ones) first check
connectivity on 1000base-x, and switch to 2500base-x afterwards. This
is considered a quirk so the phylink switches the interface to
2500base-x as well.
However, after power-cycling the uDPU device, network interface/SFP module
will not work correctly until the module is re-seated. This patch
resolves this issue by forcing the interface to be brought up in
2500base-x mode by default.
Signed-off-by: Jakov Petrina <jakov.petrina@sartura.hr>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Out of all devices currently supported based on AR9331 chipset,
this one had the 'serial0' alias missing. Add it to fix setting of
/dev/console and login shell on the onboard UART.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
As the node is already defined and labeled in SoC DTSI file, we can refer to it
outside of root node and reduce redundancy.
While at it, remove unused pcf8563 label.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Change "0" to "0x0" for consistency. This is an extension of commit 34abfb6e91
("ramips: convert mediatek,mtd-eeprom from decimal to hex notation").
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Fixes a build error seen when applying the kernel patches.
Applying patch generic/435-mtd-add-routerbootpart-parser-config.patch
patching file drivers/mtd/parsers/Kconfig
Hunk #1 FAILED at 160.
1 out of 1 hunk FAILED -- rejects in file drivers/mtd/parsers/Kconfig
patching file drivers/mtd/parsers/Makefile
Hunk #1 FAILED at 10.
1 out of 1 hunk FAILED -- rejects in file drivers/mtd/parsers/Makefile
This was missed as 5.4 is currently set as testing kernel
while the main kernel being used is 4.19
Fixes: 2976e423dc ("generic: routerboot partition build bits")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
As evidenced here[1] the device MAC address can be stored at a random
offset in the hard_config partition. Rely on sysfs to update the MAC
address correctly.
Adjust config so that WAN is base MAC and LAN is base MAC +1 to better
match label and vendor OS.
[1] https://github.com/openwrt/openwrt/pull/2850#issuecomment-610809021
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
As evidenced here[1] the device MAC address can be stored at a random
offset in the hard_config partition. Rely on sysfs to update the MAC
address correctly.
To match sticker and vendor OS behavior, WAN MAC is set to the device
base MAC and LAN MAC is incremented from that.
Note: this will trigger a harmless kernel message during boot:
ag71xx 19000000.eth: invalid MAC address, using random address
There is no clean workaround to prevent this message from being emitted.
[1] https://github.com/openwrt/openwrt/pull/2850#issuecomment-610809021
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Some newer MikroTik RouterBOARD devices use a new encoding scheme
for their WLAN calibration data. This patch provides support for
decoding this new scheme.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
This driver exposes the data encoded in the "hard_config" flash segment
of MikroTik RouterBOARDs devices. It presents the data in a sysfs folder
named "hard_config". The WLAN calibration data is available on demand via
the 'wlan_data' sysfs file in that folder.
This driver permanently allocates a chunk of RAM as large as the
"hard_config" MTD partition (typically 4KB), although it is technically
possible to operate entirely from the MTD device without using a local
buffer (except when requesting WLAN calibration data), at the cost of a
performance penalty.
This driver does not reuse any of the existing code previously found in
routerboot.c.
This driver has been successfully tested on BE (ath79) and LE (ipq40xx
and ramips) hardware.
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Tested-by: Baptiste Jonglez <git@bitsofnetworks.org>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
Tested-by: Christopher Hill <ch6574@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
This driver provides an OF MTD parser to properly assign the RouterBoot
partitions on the flash. This parser builds from the "fixed-partitions"
one (see ofpart.c), but it can handle dynamic partitions as found on
routerboot devices.
The parent node must contain the following:
compatible = "mikrotik,routerboot-partitions";
#address-cells = <1>;
#size-cells = <1>;
Children routerbootpart DTS nodes are defined as follows:
For fixed partitions
node-name@unit-address {
reg = <prop-encoded-array>;
label = <string>;
read-only;
lock;
};
All properties but reg are optional.
For dynamic partitions:
node-name {
size = <prop-encoded-array>;
label = <string>;
read-only;
lock;
};
size property is mandatory unless the next partition is a fixed one or
a "well-known" one (matched from the strings defined below) in which case
it can be omitted or set to 0; other properties are optional.
By default dynamic partitions are appended after the preceding one, except
for "well-known" ones which are automatically located on flash.
Well-known partitions (matched via label or node-name):
- "hard_config"
- "soft_config"
- "dtb_config"
This parser requires the DTS to list partitions in ascending order as
expected on the MTD device.
This parser has been successfully tested on BE (ath79) and LE (ipq40xx
and ramips) hardware.
Tested-by: Baptiste Jonglez <git@bitsofnetworks.org>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
Tested-by: Christopher Hill <ch6574@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
ar8229 and ar8236 don't allow unknown unicast/multicast frames and
broadcast frames to be flooded to cpu port. This isn't desired behavior
for swconfig as we treat it as a standalone switch.
Current code doesn't enable unicast frame flooding for ar8229 and uses
wrong setup for ar8236. This commit fixes both of them by enabling port
0 flooding for all unknown frames.
Fixes: FS#2848
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Like for Ubiquiti PowerBeam 5AC Gen2, the highest RSSI LED can
be exploited to indicate boot/failsafe/upgrade for the NanoBeam AC
and Nanostation AC as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 80a094aaf3)
If you want to use the Raspberry Pi UART, "console=serial0,115200" needs
to be removed from the kernel cmdline. This is done by editing
/boot/cmdline.txt. However, this file is not currently backed up during
sysupgrade, so this effectively breaks HATs that require the use of the
UART every sysupgrade.
Backup this file during sysupgrade, and restore it before rebooting.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This board was previously supported in ar71xx as 'RUT9XX'. The
difference between that and the other RUT955 board already supported in
ath79 is that instead of the SPI shift registers driving the LEDs and
digital outputs that model got an I2C GPIO expander instead.
To support LEDs during early boot and interrupt-driven digital inputs,
I2C support as well as support for PCA953x has to be built-in and
cannot be kernel modules, hence select those symbols for ath79/generic.
Specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344)
- built-in 4G/3G module (example: Quectel EC-25EU)
- internal microSD slot (spi-mmc, buggy and disabled for now)
- RS232 on D-Sub9 port (Cypress ACM via USB, /dev/ttyACM0)
- RS422/RS485 (AR934x high speed UART, /dev/ttyATH1)
- analog 0-24V input (MCP3221)
- various digital inputs and outputs incl. a relay
- 11x LED (4 are driven by AR9344, 7 by PCA9539)
- 2x miniSIM slot (can be swapped via GPIO)
- 2x RP-SMA/F (Wi-Fi), 3x SMA/F (2x WWAN, GPS)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- debugging UART available on PCB edge connector
Serial console (/dev/ttyS0) pinout:
- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side
Flash instruction:
Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.06.051" firmware and U-Boot "3.0.1".
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Split device-tree of Teltonika RUT955 into a generic RUT9xx part and
a part specific to that version of RUT955 already supported.
Also harmonize GPIO and LED names with what is used by the vendor
firmware and assign RS485 DTR signal.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds some still-missing board names for old TP-Link devices
to ath79 SUPPORTED_DEVICES.
Fixes: FS#3017
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit a1693bf626.
The rt288x and rt3883 devices in question don't have switches.
Only keep the merged case for rt305x.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch removes support for swconfig and switches to dsa driver.
swconfig and switch drivers are removed. DSA driver is enabled and
configuration is adjusted.
In kirkwood only two devices have switches: Linksys EA3500 and EA4500.
WAN MAC configuration in 02_network is required because otherwise WAN
would have the same MAC address as lan interfaces. In swconfig solution
the WAN address was assigned in u-Boot to eth1. Now, as eth1 is disabled
and wan is part of the switch, we have to set it manually.
Compile tested: EA3500, EA4500
Run tested: EA4500
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[minor commit title/message adjustments, remove swconfig package
for devices]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
According to a user in OpenWrt forum, on RouterOS the MAC addresses are
ether1(WAN) = MAC
ether2(LAN2) = MAC+1
ether3(LAN3) = MAC+2
etc.
Fix the MAC addresses in OpenWrt.
Ref: https://forum.openwrt.org/t/few-dumb-question-about-mt7530-rb750gr3-dsa/61608
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[remove label_mac in 02_network]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Like for Ubiquiti PowerBeam 5AC Gen2, the highest RSSI LED can
be exploited to indicate boot/failsafe/upgrade for the NanoBeam AC
and Nanostation AC as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In rt3883 subtarget, several devices add swconfig to their DEVICE_PACKAGES.
This is redundant as the package is already provided via DEFAULT_PACKAGES.
Remove the redundant inclusions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
These definitions are not required since swconfig is selected for
the target anyway and kmod-swconfig is pulled as dependency by
kmod-switch-rtl8366rb.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Commit 8f6334eb94 ("ramips: explicitly disable built-in switch when needed")
did not fix rt288x and rt3883 devices. This patch deals with them.
While at it, consolidate duplicate cases in interface setup.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Three of the I-O DATA devices with NAND flash share a lot of
variables. Create a common definition for them to reduce duplicate
code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This fixes following compile error:
```
CC drivers/net/ethernet/mediatek/mtk_eth_soc.o
drivers/net/ethernet/mediatek/mtk_eth_soc.c:70:5: error: conflicting types for 'mtk_m32'
u32 mtk_m32(struct mtk_eth *eth, u32 mask, u32 set, unsigned reg)
^~~~~~~
In file included from drivers/net/ethernet/mediatek/mtk_eth_soc.c:25:
drivers/net/ethernet/mediatek/mtk_eth_soc.h:964:6: note: previous declaration of 'mtk_m32' was here
void mtk_m32(struct mtk_eth *eth, u32 clear, u32 set, unsigned reg);
^~~~~~~
```
which caused by 5.4.34 mainlining of mtk_m32 function.
Fixes: faf668be35 ("kernel: bump 5.4 to 5.4.34")
Signed-off-by: Yong-hyu, Ban <perillamint@quendi.moe>
The official sysupgrade images for I-O DATA devices manufactured by
MSTC (MitraStar Technology Corp.) cannot be booted normally and the
kernel panics after switching to kernel 5.4.
This commit fixes the issue by using lzma-loader.
Note:
These devices use Z-LOADER to read the kernel from NAND flash and boot
it. Z-LOADER cannot load and start plain lzma-loader, so additional
lzma-compression is needed.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Co-developed-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Tested-by: Yanase Yuki <dev@zpc.sakura.ne.jp> [wn-ax2033gr]
In several Japanese routers with MT7621 SoC, the official sysupgrade
image cannot be booted properly after switching to kernel 5.4.
This commit fixes the issue by using lzma-loader.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This device has trouble extracting big kernel from flash,
and supports LZMA compressed kernels only.
Using OpenWrt kernel loader saves us 64 KB compared to the dictionary
size limiting workaround.
Factory image sizes (commit: 5f126c541a) with "CONFIG_ALL_KMODS=y":
- original ("-d23", default): 4784188 bytes, LZMA ERROR 1
- with "-d19": 4915260, LZMA ERROR 1
- with "-d18": 4915260, diff to original: +128 KB
- with "-d17": 4980796, diff to original: +192 KB
- with this patch: 4849724, diff to original: +64 KB
To save some CPU cycle, use minimal compression ("-a0") for the LZMA
compressed uImage.
The most robust solution would use a different loader,
which reads the compressed kernel directly from the flash.
See the thread at [0] for more details!
[0] http://lists.infradead.org/pipermail/openwrt-devel/2020-April/022926.html
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
[fixed identation]
Signed-off-by: David Bauer <mail@david-bauer.net>
These boards suffer from a sudden inability to establish a link on the
SGMII. Enable the workaround to fix the link when it dies.
Signed-off-by: David Bauer <mail@david-bauer.net>
ath79 does not support kernels prior to 4.19 anymore.
Remove legacy code for those kernels from the ag71xx driver.
Signed-off-by: David Bauer <mail@david-bauer.net>
This parser was added with the target, but no device seems to use it
currently, as all partitions are specified in the device-tree.
Signed-off-by: David Bauer <mail@david-bauer.net>
Upstream commit dda9f4b9ca ("f2fs: fix to skip verifying block address
for non-regular inode").
On 4.14, attempting to perform operations on a non-regular inode
residing on an f2fs filesystem, such rm-ing a device node, would fail
and lead to a warning / call trace in dmesg. This fix was already
applied to other kernels upstream - including 4.19, from which the patch
was taken.
More info at https://bugzilla.kernel.org/show_bug.cgi?id=202495.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
This fixes a bunch of cosmetic issues with GL.iNet GL-MV1000:
- apply alphabetic sorting in multiple files
- use armada-3720 prefix for DTS like for other devices
- fix vendor capitalization for model in DTSes
- remove trivial comment in DTS files
- use DEVICE_VENDOR/DEVICE_MODEL
- remove redundant SUPPORTED_DEVICES
- use SOC instead of DEVICE_DTS
- remove empty line at EOF
Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
kmod-usb-dwc2 and kmod-usb-ledtrig-usbport are not target default packages, and
Belkin F7C027 does not have a USB port anyway. Just drop it.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Currently SUPPORTED_DEVICES only contains the old device string. Fix it by
removing the first assignment.
Fixes: c2334ad60d ("ramips/mt76x8: Synchronize Makefiles with DTS compatible")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This service file has been misplaced from the very beginning.
Fixes: dcc34574ef ("oxnas: bring in new oxnas target")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
SFP cage of this device is connected via a AT8031 phy to port 5 of the switch.
This phy act as a RGMII-to-SerDes converter.
Also a I2C clock gate needs to be enabled in order to access the SFP module via I2C bus.
SFP cage also has module detect pin which is connected to I2C gpio expander.
With this patch the kernel/PHYLINK now can detect, readout and use the SFP module/port.
NOTE: SFP cage / AT8033 PHY only support 1000base-X encoding!
This means that some SGMII modules can work and only at forced 1GBit/full-duplex!
Signed-off-by: René van Dorst <opensource@vdorst.com>
This patch is needed for clause 37 1000Base-X encoding used in many SFP modules.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: René van Dorst <opensource@vdorst.com>
Commit 0543eb1110 ("imx6: 5.4: add missing kernel perf monitor
symbol") has added missing kernel config symbol FSL_IMX8_DDR_PMU which
is exposed only when building perf, so add it back.
Fixes: 8d9b36270b ("imx6: refresh kernel config")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The fritz 7312 does not support 1000 gbit. Advertising it makes it
worse. Some NIC will change to 1000 gibt and turn off and on again for
ever.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Some boards using a QCA9556 or QCA9558 had their machine compatible
binding incorrectly set to qca,qca9557.
Signed-off-by: David Bauer <mail@david-bauer.net>
There are at least 3 different chips in the Scorpion series of SoCs.
Rename the common DTSI to better reflect it's purpose for the whole
series.
Also rename the compatible bindings from qca,ar9557 and qca,qca9557
to qca,qca9550.
Signed-off-by: David Bauer <mail@david-bauer.net>
Between 4.19 and 5.4, mtd parsers have been moved to "parsers"
subdirectory. Like for myloader.c in the previous patch,
this patch moves tplinkpart.c to the kernel patches, so the
code and the kernel includes are at the same location and
the path can be adjusted per kernel.
While at it, remove some outdated kernel version switches from
the C code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Between 4.19 and 5.4, mtd parsers have been moved to "parsers"
subdirectory. Based on this, the selection of myloader.o in OpenWrt
was also moved to that subdirectory, while the Kconfig and our local
myloader.c file remained in /drivers/mtd.
This resulted in linking errors like the following (on ath25@5.4):
make[8]: *** No rule to make target 'drivers/mtd/parsers/myloader.o', ...
needed by 'drivers/mtd/parsers/built-in.a'. Stop.
make[7]: *** [scripts/Makefile.build:500: drivers/mtd/parsers] Error 2
make[6]: *** [scripts/Makefile.build:500: drivers/mtd] Error 2
Since myloader.c is not too big, this patch moves it to the kernel patches,
allowing to adjust the path for kernel 5.4 and keeping Makefiles and
file paths better in sync.
Other patches have been refreshed accordingly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The bootloader does not always initialize the MDIO pins before booting
Linux. E.g. on version "U-Boot 2012.07 [Chaos Calmer 15.05.1,r35193] (Jul
25 2017 - 11:36:26)" this is the case when booting automatically without
activating the U-Boot console.
Without this change, the kernel boot will complain about missing PHYs:
libphy: ipq40xx_mdio: probed
ar40xx c000000.ess-switch: Probe failed - Missing PHYs!
libphy: Fixed MDIO Bus: probed
With this change it will work as expected:
libphy: ipq40xx_mdio: probed
ESS reset ok!
ESS reset ok!
libphy: Fixed MDIO Bus: probed
Ref: GH-2835
Tested-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit description from Fredrik, subject facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
mt7621 and mt76x8 subtargets have been moved to kernel 5.4 and their
DTS(I) files are incompatible to kernel 4.14.
Remove the corresponding kernel config files to signal that more
boldly and to prevent accidentally patching the wrong kernel when
pulling in older config patches.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
