If an external module uses exported symbols from another external
module, Kbuild needs to have full knowledge of all symbols to
avoid spitting out warnings about undefined symbols.
Use PKG_EXTMOD_SUBDIRS to point to the build directory which contains
the Module.symvers.
Pass KERNEL_MAKE_FLAGS to the external module build, to inject
KBUILD_EXTRA_SYMBOLS. KBUILD_EXTRA_SYMBOLS holds a space separated list
of Module.symvers, which list all exported symbols.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The USB ports if a FRIZZ!Box 7320 do not supply power to connected
devices.
Add the GPIOs enabling USB power as regulator, to enable USB power
supply as soon as the USB driver is loaded.
Fixes FS#3624
Signed-off-by: Mathias Kresin <dev@kresin.me>
When recursively deleting partitions, don't acquire the masters
partition lock twice. Otherwise the process endy up in a deadlocked
state.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
MediaTek MT7622
512MB DDR3 RAM
64M SPI-NOR Flash (Winbond W25Q512JV)
MediaTek MT7622 802.11bgn 4T4R WMAC
MediaTek MT7915 802.11ax 4T4R
Marvell AQR1112 100/1000/2500 NBase-T PHY
Holtek HT32F52241 LED controller
Reset Switch
UART
----
CPU UART0 at the pinout next to the Holtek MCU.
Pinout (first pin next to SoC / MCU)
0 3V3
1 RX
2 TX
3 GND
Settings are 115200 8N1.
Opening the case
----------------
Opening the case is not a nice task, as itis glued together. Insert a
flat knife between the front and back casing below the ethernet port.
Open up a gap this way and insert a flat scredriver, remove the knife.
Work your way around the casing by applying force to seperate the front
and back casing. This losens the glue and opens the plastic clips. Be
gentle, as these clips are very cheap and break quickly.
Installation
------------
1. Connect to the booted device at 192.168.1.20 using username/password
"ubnt".
2. Transfer the OpenWrt sysupgrade image to the device using SCP.
3. Check the mtd partition number for bs / kernel0 / kernel1
$ cat /proc/mtd
4. Set the bootselect flag to boot from kernel0
$ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6
5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1
$ dd if=openwrt.bin of=/dev/mtdblock8
$ dd if=openwrt.bin of=/dev/mtdblock9
6. Reboot the device. It should boot into OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add a driver for controlling the RGB LED via Ubiquitis own "LEDBAR" LED
controller based on the Holtek HT32F52241 MCU.
This driver is initially used by the Ubiquiti UniFi 6 LR, however
judging from FCC pictures the MCU is also found on the U6-Mesh as well
as the U6-Extender.
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes 4 security vulnerabilities/bugs:
- CVE-2021-2839 - SSLv2 vulnerability. Openssl 1.1.1 does not support
SSLv2, but the affected functions still exist. Considered just a bug.
- CVE-2021-2840 - calls EVP_CipherUpdate, EVP_EncryptUpdate and
EVP_DecryptUpdate may overflow the output length argument in some
cases where the input length is close to the maximum permissable
length for an integer on the platform. In such cases the return value
from the function call will be 1 (indicating success), but the output
length value will be negative.
- CVE-2021-2841 - The X509_issuer_and_serial_hash() function attempts to
create a unique hash value based on the issuer and serial number data
contained within an X509 certificate. However it was failing to
correctly handle any errors that may occur while parsing the issuer
field (which might occur if the issuer field is maliciously
constructed). This may subsequently result in a NULL pointer deref and
a crash leading to a potential denial of service attack.
- Fixed SRP_Calc_client_key so that it runs in constant time. This could
be exploited in a side channel attack to recover the password.
The 3 CVEs above are currently awaiting analysis.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Add m4 patch to avoid conflict with tools/autoconf-archive.
Add build parallel as it seems to work now.
Remove a bunch of uClibc-ng hacks as it is not in the tree anymore.
Format security patch was fixed upstream.
Refreshed other patches.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This patch has been added to 5.4, but not been copied to 5.10:
7495acb555 ("kernel: backport mtd commit converting partitions doc syntax")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This applies another patch from 5.4 to 5.10 as well:
de09355f74 ("kernel/hack-5.4: make UDP tunneling user-selectable")
UDP tunneling support isn't user-selectable, but it's required by WireGuard
which is, for the time being, an out-of-tree module. We currently work around
this issue by selecting an unrelated module which depends on UDP tunnelling
(VXLAN). This is inconvenient, as it implies this unrelated module needs to be
built-in when doing a monolithic build.
Fix this inconvenience by making UDP tunneling user-selectable in the kernel
configuration.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
File extension was truncated for
pending-5.4/770-11-net-ethernet-mtk_eth_soc-avoid-rearming-interrupt-if.pa
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reapply changes added to 5.4 but not copied to 5.10:
3da4acaa7b ("kernel: fix busy wait loop in mediatek PPE code")
The intention is for the loop to timeout if the body does not succeed.
The current logic calls time_is_before_jiffies(timeout) which is false
until after the timeout, so the loop body never executes.
time_is_after_jiffies(timeout) will return true until timeout is less
than jiffies, which is the intended behavior here.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Kernel has changed the of_get_phy_mode API in commit 0c65b2b90d13
("net: of_get_phy_mode: Change API to solve int/unit warnings").
This is already included in kernel 5.5, so fix the version switch
(though this will not actually matter for the versions we support).
Similar driver adjustments to account for the API change will
probably be necessary to various other local drivers.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
After the ABI version rework, packages need to be declared in the order of
their dependencies, so that dependent packages will use the right ABI version
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Let's switch to 5.10 now that mac80211 has been updated.
Runtime-tested on ipq806x (Netgear R7800).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Fixes: FS#2086
The logic for IS_TTY was broken, because it was testing stdin
instead of stdout.
MAKE_TERMOUT was introduced in GNU Make version 4.1 (05 Oct 2014),
so it should be available everywhere nowadays.
Signed-off-by: R. Diez <rdiezmail-openwrt@yahoo.com>
